Search

Background Tension band wiring (TBW) is the standard method for treating transverse olecranon fractures, but high rates of complications and reoperations have been reported. Plate fixation (PF) with locking screws has been introduced as an alternative method that may retain the fracture reduction better with a higher load to failure. Methods Twenty paired cadaveric elbows were used. All soft tissues except for the triceps tendon were removed. A standardized transverse fracture was created, and each pair was allocated randomly to TBW or PF with locking screws. The triceps tendon was mounted to the materials testing machine with the elbow in 90° of flexion. Construct stiffness was compared 3 times. Then, the elbows underwent a chair lift-off test by loading the triceps tendon to 300 N for 500 cycles. Finally, a load-to-failure test was performed, and failure mechanism was recorded. Results The construct stiffness of PF was higher in the first of 3 measurements. No difference was observed in the cyclic test or in load to failure. Hardware failure was the failure mechanism in 8 of 10 TBW constructs, and all failures occurred directly under the twists of the metal wire. Hardware failure was the cause of failure in only 1 elbow in the PF group (P Conclusion There was no difference in fracture displacement following fixation with TBW and PF with locking screws in transverse olecranon fractures. However, assessment of the mode of hardware failure identified the metal cerclage twist as the weakest link in the TBW construct.

Background Clinical studies suggest that an adjunctive cerclage in intramedullary nailing of subtrochanteric fractures improves the outcome. Despite this, to what extent various cerclage configurations influences the fixation strength, remains undocumented. We tested the hypothesis that the stability of subtrochanteric fractures with a posteromedial wedge treated with long cephalomedullary nail varies with cerclage configuration. Methods 40 composite femurs with a subtrochanteric osteotomy including a posteromedial-wedge were locked by cephalomedullary nailing (T2 recon, Stryker) and divided into 4 groups. In Group-A no cerclage was applied. The Group-B received a lateral tension-band (cerclage cable with crimp, Depuy-Synthes). Without any fixation, the wedge-component was removed in these groups. The Group-C was fixed with a cerclage encircling the wedge-component, while in the Group-D a novel figure-of-8 cerclage stabilised the wedge-component. Each femur was tested quasi-static in a material-testing-machine for stiffness calculation, first horizontally to simulate seated-position and then vertically to simulate standing-position. Finally, cyclic testing was performed in the upright-posture to measure deformation over time. Findings In Group-D the mean stiffness in the sitting-position was 6.4, 5.8 and 3.1 times higher than the Groups-A, B and C, respectively, and correspondingly 2.0, 2.1 and 1.7 times higher in the standing-position (p

Stable fixation promotes union in the common femoral neck fractures, but high non-union rates due to fixation failure remain with traditional fixations. To enhance stability, a plate interlocking pins, but without further fixation to femur has been developed. To our knowledge, no comparison to other conventional fixation methods has been performed. We tested the hypothesis that the novel implant biomechanically leads to a more stable femoral neck fixation.Fifty synthetic femurs with a cervical wedge osteotomy were allocated to intervention with three hook-pins interlocked in a plate (Hansson Pinloc® System) or standard fixations with a two-hole Dynamic Hip Screw® plate with an anti-rotational screw, three cannulated screws (ASNIS® III) or two screws (Olmed® or Cannulated Hip Screws®). Quasi-static non-destructive torsion around the neck, anteroposterior bending and vertical compression were tested to detect stiffness. The specimen's deformation was evaluated after cyclic compression simulating weight-bearing. Local deformation of implant channels was measured. Fixation failure was defined by fissure formation.Compared to the conventional implants all together, the interlocked pins enhanced mean stiffness 130% in torsion and 33% in bending (P 0.001), while compressive stability was increased by a reduced deformation of 62% in average of the global test specimen and 95% decreased local implant channel deformation after cycling (P 0.001). In comparisons with each of the standard fixations the interlocking pins revealed no signs of adverse effects.The novel femoral neck interlocking plate allowed dynamic compression and improved multi-directional stability compared to the traditional fixations.