Search

Introduction: Titanium (Ti) is widely accepted as a biomaterial for orthopaedic and dental implants, primarily due to its capacity to integrate directly into the bone and its superior corrosion resistance. It has been suggested that titanium–zirconium alloy (TiZr), with 13–17% of zirconium, has better mechanical properties than pure Ti, but there are very few published studies assessing the suitability of TiZr for high-load- bearing implants. This study aimed to compare the mechanical properties and microstructures of TiZr and commercially pure titanium (Ti). Methodology: Pure Ti and TiZr alloy discs were prepared and subjected to characterisation by nanoindentation, electron dispersive spectroscopy (EDS), X-ray diffraction (XRD), and electron backscatter diffraction (EBSD). Results: The TiZr alloy was found to have significantly lower elastic modulus value (p < 0.0001) and greater hardness than Ti (p < 0.05). The EDS results confirmed the presence of Zr (13–17%) in the TiZr alloy, with XRD and EBSD images showing microstructure with the alpha phase similar to commercially available Ti. Conclusion: The lower elastic modulus, higher hardness, presence of alpha phase, and the finer grain size of the TiZr alloy make it more suitable for high-load-bearing implants compared to commercially available Ti and is likely to encourage a positive biological response.

The underlying causes of maxillary bone loss during lactation remain poorly understood. We evaluated the impact of lactation on physiological and mechanically-induced alveolar bone remodeling. Nulliparous non-lactating (N-LAC) and 21-day lactating (LAC) mice underwent mechanically-induced bone remodeling by orthodontic tooth movement (OTM). Micro-computed tomography (microCT) was performed in the maxilla, femur and vertebra. Tartrate-resistant-acid phosphatase (TRAP) and Masson's trichrome labelling was performed in the maxillary bone and gene expression was determined in the periodontal ligament. The effect of prolactin on osteoclast (OCL) and osteoblast (OBL) differentiation was also investigated in N-LAC and LAC mice. Lactation increased alveolar bone loss in the maxilla, femur and vertebra, while OTM was enhanced. The number of OCL and OBL was higher in the maxilla of LAC mice. OTM increased OCL in both groups; while OBL was increased only in N-LAC but not in LAC mice, in which cell numbers were already elevated. The alveolar bone loss during lactation was associated with increased expression of receptor activator of nuclear factor-KappaB (RANK), RANK ligand (RANKL), and osteoprotegerin (OPG) in the maxilla. OTM induced the same responses in N-LAC mice, whereas it had no further effect in LAC mice. Lactation enhanced differentiation of OCL and OBL from bone marrow cells, and prolactin recapitulated OCL differentiation in N-LAC mice. Thus, lactation increases physiological maxillary bone remodeling and OTM, and both require activation of RANK/RANKL/OPG system. These findings expand our knowledge of lactation-induced osteopenia and have possible impact on clinical practice regarding orthodontic treatments and dental implants in lactating women.

Background Keratin has shown promising outcomes as a biomaterial due to its inherent bioactivity, biocompatibility and regenerative effects. The effect of keratin on repair and regeneration of dental tissues has never been studied before. Current therapies to treat pulp tissues involve its replacement with inert, synthetic materials that do not have a proper biological function, leading to failure and tooth loss. This study aimed to develop a biocompatible keratin hydrogel (KH) suitable for pulp therapies. Methods Keratins extracted from sheep wool were isolated, quantified and reconstituted to form KH. Different concentrations of keratin gel suitable for dental application were characterized by rheological analysis. The optimized gel based on flow characteristics was studied further for microstructure including porosity, percentage swelling ratio and contact angle measurements, using analytical tools such as scanning electron microscopy (SEM), micro-computed tomography and goniometer. To assess both biocompatibility and pulpal response, KH was implanted into rat upper molar teeth following partial pulpotomy. After 28 days, the tissue sections were analyzed by histological and immunohistochemical methods to identify dentin matrix protein 1 (DMP-1) formation and compared with control (Ca(OH)2-treated) teeth. Results The results of the study demonstrated a viscous and injectable, porous, dimensionally stable, hydrophilic and biocompatible gel that allowed pulp healing to occur by a reparative response, with widespread DMP-1 expression. Conclusions The findings of this study indicate that keratins can be developed as a biomaterial source for alternate biological treatment options for pulp therapies.

The choice of implant surface has a significant influence on osseointegration. Modification of TiZr surface by anodization is reported to have the potential to modulate the osteoblast cell behaviour favouring more rapid bone formation. The aim of this study is to investigate the effect of anodizing the surface of TiZr discs with respect to osseointegration after four weeks implantation in sheep femurs. Titanium (Ti) and TiZr discs were anodized in an electrolyte containing dl-α-glycerophosphate and calcium acetate at 300 V. The surface characteristics were analyzed by scanning electron microscopy, electron dispersive spectroscopy, atomic force microscopy and goniometry. Forty implant discs with thickness of 1.5 and 10 mm diameter (10 of each-titanium, titanium–zirconium, anodized titanium and anodized titanium–zirconium) were placed in the femoral condyles of 10 sheep. Histomorphometric and histologic analysis were performed 4 weeks after implantation. The anodized implants displayed hydrophilic, porous, nano-to-micrometer scale roughened surfaces. Energy dispersive spectroscopy analysis revealed calcium and phosphorous incorporation into the surface of both titanium and titanium–zirconium after anodization. Histologically there was new bone apposition on all implanted discs, slightly more pronounced on anodised discs. The percentage bone-to-implant contact measurements of anodized implants were higher than machined/unmodified implants but there was no significant difference between the two groups with anodized surfaces (P > 0.05, n = 10). The present histomorphometric and histological findings confirm that surface modification of titanium–zirconium by anodization is similar to anodised titanium enhances early osseointegration compared to machined implant surfaces.