Search

Inhaled drugs are routinely used for the treatment of respiratory-supported patients. To date, pressurized metered dose inhalers and nebulizers are the two platforms routinely employed in the clinical setting. The scarce utilization of the dry powder inhaler (DPI) platform is partly due to the lack of in vivo data that proves optimal delivery and drug efficacy are achievable. Additionally, fitting a DPI in-line to the respiratory circuit is not as straightforward as with the other aerosol delivery platforms. Importantly, there is a common misconception that the warm and humidified inspiratory air in respiratory supports, even for a short exposure, will deteriorate powder formulation compromising its delivery and efficacy. However, some recent studies have dispelled this myth, showing successful delivery of dry powders through the humidified circuit of respiratory supports. Compared with other aerosol delivery devices, the use of DPIs during respiratory supports possesses unique advantages such as rapid delivery and high dose. In this review, we presented in vitro studies showing various setups employing commercial DPIs and effects of ventilator parameters on the aerosol delivery. Inclusion of novel DPIs was also made to illustrate characteristics of an ideal inhaler that would give high lung dose with low powder deposition loss in tracheal tubes and respiratory circuits. Clinical trials are urgently needed to confirm the benefits of administration of dry powders in ventilated patients, thus enabling translation of powder delivery into practice.

Novel inhalable and controlled release powder formulations of ciprofloxacin nanocrystals inside liposomes (CNL) were recently developed. In the present study, the storage stability of CNL powders consisting of lyoprotectant (i.e. sucrose or lactose), lipids, ciprofloxacin ( CIP ), and magnesium stearate or isoleucine was investigated. These powders were produced by spray drying, collected in a dry box at < 15% relative humidity (RH), then stored at room temperature and either 4 or 20 %RH. Liposomal integrity, CIP encapsulation efficiency (EE), in vitro drug release (IVR), aerosol performance, and solid-state properties were examined over six months. Sucrose CNL powder exhibited consistent liposomal integrity, aerosol performance, and controlled release of CIP over six months of storage at 4 %RH. However, storage of the powder at 20 %RH for the same period caused sucrose crystallization and consequently a significant drop in EE and aerosol performance (p-values 50). Lactose CNL maintained superior aerosol performance over the six months irrespective of the storage RH. However, liposomal instability occurred at both RHs within the first month of storage with a significant drop in EE and an increase in liposome size (p-values

Spray drying is a rapid method for converting a liquid feed into dried particles for inhalation aerosols. Lactose is a major inhalation excipient used in spray-dried (SD) formulations. However, SD powders produced from solutions are usually amorphous hence unstable to moisture. This problem can potentially be minimized by spray drying a suspension (instead of solution) containing crystalline lactose particles and dissolved drugs. In the present study, the suspension formulation containing dissolved budesonide (BUD) or rifampicin (RIF) and suspended lactose crystals in isopropanol alcohol (IPA) were produced. For comparison, powders were also produced from solution formulations containing the same proportions of drug and lactose dissolved in 50:50 IPA/water as controls. These SD powders were stored at 25 °C/60% RH and 40 °C/75% RH for six months. The particulate properties and in vitro dispersion performance were examined at various storage time points. All powders obtained from spray drying of solutions recrystallized after one week of storage at 25 °C/60% RH. In contrast, SD BUD-lactose obtained from suspension did not change until after three-months of storage when the particle size increased gradually with morphology change and yet the crystallinity remained the same as determined by X-ray powder diffraction. For the SD RIF-lactose obtained from suspension, both particulate properties and in vitro powder dispersion performance showed no significant difference before and after storage at both storage conditions. To conclude, this is the first study to show that SD powder formulations obtained from suspensions containing lactose crystals demonstrated superior storage stability performance, which is desirable for inhaled powders.

Lactose is widely used as an approved excipient for dry powder inhaler (DPI) products. Spray drying technique is a rapid method for converting a liquid feed into inhalable dried particles. However, spray-dried (SD) lactose powders produced from solutions are mostly amorphous and particularly unstable when exposed to moisture. In the present study, we explored the use of spray drying suspensions containing crystalline lactose particles in an organic solvent, and investigated the physicochemical properties of the resulting powders. The solution formulation was spray dried as a control. Two conditioned crystalline lactose samples were used for suspension formulations: Lactohale (LH) 300 lactose and jet-milled (JM) lactose micronized from LH300. The suspension formulations each contained 12 mg/ml suspended crystalline lactose particles (either LH300 or JM lactose) in isopropyl alcohol. The solution formulation contained 60 mg/ml lactose in water. The SD powders were stored under 25 °C/60% RH and 40 °C/75% RH for 3 months. The particulate properties and in vitro dispersion performance were examined at various time points. The SD lactose obtained from solution recrystallized and was no longer dispersible after 1-day storage at both storage conditions. The suspension SD JM lactose powder showed deterioration in the particulate properties and dispersibility over time, but more gradually. In contrast, the SD LH300 powder was stable, with its particulate properties and dispersion performance (FPF: ~12%) remaining the same after 3-months storage at 25 °C/60% RH. The SD LH300 stored at 40 °C/75% RH showed no change in particulate properties, but the FPF decreased over 3 months. Overall, SD lactose powders obtained from suspension demonstrated superior stability performance compared to SD lactose obtained from solution.

Soft mist inhalers (SMIs) generate aerosols with a smaller particle size than pressurized metered-dose inhalers (pMDIs). However, the whole-span particle size distribution (PSD) of SMIs and the optimal delivery method of SMIs during mechanical ventilation have not been fully investigated. This study aimed to measure the PSD of the SMI alone and the SMI coupled to an inhalation aid (eg, a spacer, a valved holding chamber), as well as the delivery efficiency of SMI in different actuation timings and circuit positions during mechanical ventilation. As a suitable comparison, the pMDI was chosen for the same measurement.SMIs (2.5 μg/actuation of tiotropium) were compared with pMDIs (100 μg/actuation of salbutamol). A microorifice uniform deposit impactor was utilized for the particle sizing of drug aerosols generated by inhalers alone, inhalers with a spacer, and inhalers with a valved holding chamber. To optimize the delivery efficiency of both inhalers during mechanical ventilation, the operating parameters included the circuit positions and actuation timings in the ventilator circuit. Particle sizes and inhaled doses were measured with an optical particle sizer and filters used to collect and quantify the drug, respectively.The SMI generated a smaller mass medium aerodynamic diameter (MMAD) than that from the pMDI. The extrafine-particle fraction (EFPF,1 μm) of the SMI was significantly higher than that of the pMDI. With the use of either inhalation aid, the MMAD of both inhalers decreased, and both inhalers with inhalation aid showed significant increases in EFPF. During mechanical ventilation, the optimum way to deliver the SMI and pMDI was at 15 cm from the Y-piece and actuated at the end of expiration and the onset of inspiration, respectively.The SMI with an inhalation aid showed marginal improvement on the PSD. The inhaler type, actuation timing, and position within the circuit also played important roles in delivery efficiency during mechanical ventilation.