Search

This study presents the influence of initial deflection angle (IDA) on the tribological properties of gray cast iron (GCI) rings with curve distributed pits in the radial direction (CDPRD). The thermal behavior of pits textured GCI rings with different initial deflection angles (0°, 30°, 45°, 60°, 75°) and fixed deflexional angle of adjacent pits (DAAP, 10°) were researched, through APDL programming. A pin-on-disc wear test rig was used to reveal the anti-wear performance of samples under dry sliding, at a rotating speed of 200 rpm, with a normal load of 70 N. An electronic balance and an optical microscope (OM) were used to obtain their wear losses and worn surfaces, respectively. The results show that: comparing with the smooth GCI ring, there are evident high temperature regions between two adjacent pits groups, called “temperature barrier and separation effect”. Among all textured samples, the von Mise’s stress of IDA45 is the most stable, and its temperature is almost the lowest. The friction coefficient curve and the wear loss of IDA45 are also the lowest, and much lower than the loss of smooth GCI ring, indicating the excellent anti-wear performance. This work can provide a valuable reference for the surface design of journal bearings.

This study presents the influence of Zr/ZrN coatings on the tribological performance of pits textured grey cast iron parts under dry sliding. A laser marking system and a physical vapor deposition equipment were applied to manufacture pits textured grey cast iron rings combined with Zr/ZrN coatings. A pin-on-disc wear test rig was used to reveal the wear behavior of samples under dry wear condition, at a rotating speed of 200 r/min, with a normal load of 70 N. The wear losses and the worn surfaces of all rings were obtained by an electronic balance and a three-dimensional surface profilometer, respectively. The results show that Zr/ZrN coatings can significantly increase the surface roughness and surface hardness of grey cast iron rings. As a result, Zr/ZrN coatings increase the friction coefficients of all coated GCI rings, and reduce the wear losses of some ones. In this work, when surface texturing combines with Zr/ZrN coatings, the final tribological properties of coated grey cast iron rings may be either improved or deteriorated, depending on surface characteristics, texturing parameters and loads. Compared with the uncoated smooth grey cast iron ring, Zr/ZrN coatings cannot effectively improve the wear behavior of pits textured samples. Among all coated grey cast iron rings, when the diameter of the pit is 0.8 mm, and the distance between pits is 1.25 mm, the pits textured grey cast iron ring can provide the optimal anti-wear performance. This work would provide a valuable reference for the surface design of journal bearings and roller bearings.

Laser metal deposition (LMD) is a common manufacturing technique of laser additive manufacturing (LAM) which belongs to coaxial powder feeding method. The LMDed SS304 specimens are fabricated by the same combination of the process parameters so that they have the similar properties. The microstructure is similar to that of the selective laser melted (SLMed) specimen. The grain sizes of the LMDed specimen are compared with those of the specimens manufactured by the traditional method and SLM. Through the calculation of Ni and Cr equivalents in the LMDed SS304 specimen and the analytical results of electron backscattered diffraction (EBSD) and energy dispersive spectroscope (EDS), the phase compositions of the LMDed SS304 specimen are evaluated. The hardness of the LMDed specimen is compared with that of the conventionally manufactured wrought SS304 and SLMed specimens. And due to the differences of the grain size and phase composition on the different directions, the hardness of the LMDed specimen is anisotropic. The static tensile properties (ultimate tensile strength (UTS), yield strength (σ0.2) and elongation (EL)) and fatigue strength (FS) of the LMDed specimen are compared with those of the specimens made by the traditional method and SLM. The S N curve is established by the multiple experiments. Scanning electron microscopy (SEM) is applied to observe the fracture morphology of the static tension and tension-compression fatigue tests. And EDS is applied to analyze the chemical compositions of the particles on the fracture surface. As expected, LMD has the higher static tensile properties and fatigue strength than those of the specimen manufactured by the traditional method.

© 2018 Risheng Long et al. Inspired by the nonsmooth surface of the head of the dung beetle, grey cast iron (GCI) samples with pit textured surfaces were designed and fabricated, based on pin-on-disc friction tester. Using a tribology wear testing rig and APDL programming, the tribological behavior of smooth and textured samples was investigated and reported, both experimentally and numerically. The results show that pits can significantly change the thermal stress and temperature distribution on the surface, which will result in either positive or negative effects on the wear resistance of GCI samples, depending on the parameters. When diameter of the pit (DOP) equals 0.8 mm and distance between pits (DBP) is 1.0 mm, the pit textured surface provided the best wear resistance among all samples tested.

© Copyright 2017 Shaoni Sun et al. To investigate the influence of surface features, in the form of pits, on the wear resistance of grey cast iron (GCI), a finite element model of the pin-on-disc friction system, with pits distributed in a curved radial d irection, was developed using APDL programming and the tribological behavior of textured surfaces was studied. The influence of relative rotation direction between the disc and the pin on the thermal behavior of the friction system under dry wear conditions was researched. GCI and C30E steel samples with pit textured surfaces were manufactured using laser marking equipment and tested using a tribology wear testing rig. The mass losses were measured and the worn surfaces were characterized. The influence of different rotation directions on the tribological behavior of the pit textured surfaces was also investigated. The simulation and test results revealed that rotation direction was a crucial parameter in determining the tribological behavior of surfaces with these features, regardless of the material. Under the conditions tested, when the pin rotated anticlockwise, the samples showed better friction and wear behavior than when the pin rotated clockwise. These results can provide important guidance for the optimization of the design of heavy-load brake systems and other similar applications.