Search

[EN] The development of new piston geometries has shown great potential to achieve the low levels of soot emissions required by regulation. Thus, the present paper aims to characterize the influence of a new piston design over combustion process. It is characterized by the introduction of protrusions around the periphery of the bowl, evenly spaced. The performance of this geometry is compared to other geometries that have been extensively analyzed in literature, under similar operating conditions. To achieve this objective, a single cylinder optical compression ignition engine was used with full-quartz pistons rep resenting three bowl geometries: re-entrant, stepped lip and wave-stepped lip. Two optical techniques (OH* chemiluminescence and Natural Luminosity-NL) were applied for identifying the near stoichiometric zones and the differences in the combustion evolution. The flame movement was analyzed by applying the combustion image velocimetry (CIV) algorithms. In addition, an in-cylinder pressure analysis was performed for each piston at 4.5 bar and 7.5 bar IMEP and the differences in terms of Rate of Heat Release were highlighted. A more intense reverse flow was clearly identified when using wave protrusions inside the bowl. The stepped lip and wave-stepped lip bowl present faster late cycle oxidation with much near-stoichiometric zones than re-entrant piston, The authors gratefully acknowledge General Motors Propulsion Systems-Torino S. r.I. for support the project. Daniel Lerida for his laboratory work on the engine maintenance, operation, and control. This work was partially funded by Generalitat Valenciana through the Programa Santiago Grisolia (GRISOLIAP/2018/142) program.

Enhancing mixture preparation upstream of the premixed autoignition zone is a solution to reduce soot emission formation in compression ignition engines. With this aim, in recent years, Ducted Fuel Injection (DFI) concept has been developed: DFI is based on the idea of injecting the fuel spray through a small cylindrical pipe within the combustion chamber at a certain distance from the nozzle injector hole. Recent research studies have highlighted the high potential of this innovative concept for soot mitigation in both constant volume vessel and engine-like operating conditions. However, the mechanisms driving the soot reduction have not yet been fully understood. The aim of this research work is to further investigate the DFI concept, evaluating its impact on the spray characteristics, on the air/fuel mixing and, therefore, on the soot formation phenomena. Firstly, an experimental activity was carried out by means of a constant volume vessel test bench with optical accesses to compare the spray evolution and sizing with and without duct adoption, over a wide range of vessel thermodynamic conditions and injection pressures. After that, a simulation setup was defined in the commercially available 3D-CFD software CONVERGE reproducing the experimental test bench, calibrating and validating the spray model. Firstly, the spray model was calibrated and validated considering the same non-reacting conditions exploited in the experimental analysis. Then, the calibrated spray model was used as a virtual tool to investigate the air entrainment process. As a results, the DFI adoption increases the air entrainment in the near-nozzle region caused by the high velocity spray that generates a pumping effect at the duct inlet. Moreover, mixing process is also enhanced by the turbulence distribution at the duct exit resulting in a narrower distribution of equivalence ratio at the ignition. As a consequence of the more effective air entrainment and improved turbulent mixing, DFI remarkably mitigates soot emissions, with a reduction up to 80% with respect to free spray configuration in all tested operating conditions.

In this paper, an integrated and automated methodology for the coupling between 1D- and 3D-CFD simulation codes is presented, which has been developed to support the design and calibration of new diesel engines. The aim of the proposed methodology is to couple 1D engine models, which may be available in the early stage engine development phases, with 3D predictive combustion simulations, in order to obtain reliable estimates of engine performance and emissions for newly designed automotive diesel engines. The coupling procedure features simulations performed in 1D-CFD by means of GT-SUITE and in 3D-CFD by means of Converge, executed within a specifically designed calculation methodology. An assessment of the coupling procedure has been performed by comparing its results with experimental data acquired on an automotive diesel engine, considering different working points, including both part load and full load conditions. Different multiple injection schedules have been evaluated for part-load operation, including pre and post injections. The proposed methodology, featuring detailed 3D chemistry modeling, was proven to be capable assessing pollutant formation properly, specifically to estimate NOx concentrations. Soot formation trends were also well-matched for most of the explored working points. The proposed procedure can therefore be considered as a suitable methodology to support the design and calibration of new diesel engines, due to its ability to provide reliable engine performance and emissions estimations from the early stage of a new engine development.

Nowadays, injection rate shaping and multi-pilot events can help to improve fuel efficiency, combustion noise and pollutant emissions in diesel engine, providing high flexibility in the shape of the injection that allows combustion process control. Different strategies can be used in order to obtain the required flexibility in the rate, such as very close pilot injections with almost zero Dwell Time or boot shaped injections with optional pilot injections. Modern Common-Rail Fuel Injection Systems (FIS) should be able to provide these innovative patterns to control the combustion phases intensity for optimal tradeoff between fuel consumption and emission levels.In this work, a 1D-CFD model in GT-SUITE of a solenoid ballistic Common-Rail injector was firstly refined respect to the previous work [1] and then it was validated against an extensive experimental dataset of single injections, standard double pilot and multi-pilot injection patterns (up to 4 pilot events) with almost zero dwell time between two consecutive injection events. The experimental hydraulic test data used to validate the one-dimensional model were obtained by means of the UniPG Injection Analyzer based on the Zeuch's method.The comparison between the experimental and simulated volumetric injection rates showed a more than satisfactory accuracy of the model in predicting the actual behavior of the ballistic injector for all the injection patterns tested, even for relatively complex injector command strategies, characterized by reduced Dwell Time values between consecutive injection events.

This paper investigates the potential of coated pistons in reducing fuel consumption and pollutant emissions of a 1.6 l automotive diesel engine. After a literary review on the state-of-the-art of the materials used as Thermal Barrier Coatings for automotive engine applications, anodized aluminum has been selected as the most promising one. In particular, it presents very low thermal conductivity and heat capacity which ensure a high “wall temperature swing” property. Afterwards, a numerical analysis by utilizing a one-dimensional Computational Fluid Dynamics engine simulation code has been carried out to investigate the potential of the anodized aluminum as piston Thermal Barrier Coating. The simulations have highlighted the potential of achieving up to about 1% in Indicated Specific Fuel Consumption and 6% in heat transfer reduction. To confirm the simulation results, the coated piston technology has been experimentally evaluated on a prototype engine and compared to the baseline aluminum pistons. Despite the promising potential for Indicated Specific Fuel Consumption reduction highlighted by the numerical simulation, the experimental campaign has indicated a slight worsening of the engine efficiency (up to 2% at lower load and speed) due to the slowdown of the combustion process. The primary cause of these inefficiencies is attributed to the roughness of the coating.

[EN] This article describes the main results of an investigation about counter-bore injector nozzle impact on the combustion process in a modern Euro 6 diesel engine. First, hydraulic and spray visualization tests have been performed, showing a potential advantage of such nozzle design in fuel-air mixing efficiency. Then, combustion performance has been assessed on a GM-designed 1.6-L four-cylinder engine. The engine has been installed on a dynamometric test bench and instrumented with an AVL cylinder pressure transducer for heat release rate analysis, as well as HORIBA MEXA gas analyzer for exhaust emissions and AVL 415 Smoke Meter. Engine efficiency and emissions have been analyzed on four different part-load steady-state points, representative of New European Driving Cycle and Worldwide harmonized Light duty Test Cycle certification cycles, and covering engine speeds from 1250 to 2000 r/min and brake mean effective pressure between 0.2 and 1.4 MPa. Results of indicated analysis show that counter-bore nozzles have significant differences in terms of pilot injection combustion at low load points, which in turn lead to a better ignition and shorter combustion of the main injection. In addition, an improvement of diffusive combustion is observed as load increases. Because of both, fuel consumption is reduced by approximately 1% with respect to a standard nozzle. Finally, an appreciable decrease in engine exhaust emissions has been recorded, especially in terms of particulate matter and hydrocarbon emissions. This reduction has been linked to the improvement of fuel-air mixing promoted by the counter-bore nozzle previously observed., The authors would like to thank General Motors Global Propulsion Systems-Torino S.r.l. for sponsoring the current work. Part of the equipment was purchased with the help of Generalitat Valenciana in project IDIFEDER2018 with title "Equipamiento de diagnostico optico de alta velocidad para estudiar procesos de inyeccion''.

The paper describes the results achieved in developing a new diesel combustion system for passenger car application that, while capable of high power density, delivers excellent fuel economy through a combination of mechanical and thermodynamic efficiencies improvement. The project stemmed from the idea that, by leveraging the high fuel injection pressure of last generation common rail systems, it is possible to reduce the engine peak firing pressure (pfp) with great benefits on reciprocating and rotating components light-weighting and friction for high-speed light-duty engines, while keeping the power density at competitive levels. To this aim, an advanced injection system concept capable of injection pressure greater than 2500 bar was coupled to a prototype engine featuring newly developed combustion system. Then, the matching among these features have been thoroughly experimentally examined. The results confirmed the benefits of the employment of high fuel injection pressures as a way to reduce the pfp, combining competitive performance and excellent fuel efficiency with emissions and Noise Vibration Harshness (NVH) requirements of last generation diesel engines for passenger car applications. In particular, the paper discusses the engine power and efficiency sensitivities to the boundary conditions of the charging/exhaust systems, the fuel injection pressure and the mechanical base engine design (with particular reference to the pfp). Eventually, a balanced set of targets for the entire system based on such results are carried out.

The paper describes the challenges and results achieved in developing a new high-speed Diesel combustion system capable of exceeding the imaginative threshold of 100 kW/l. High-performance, state-of-art prototype components from automotive diesel technology were provided in order to set-up a single-cylinder research engine demonstrator. Key design parameters were identified in terms boost, engine speed, fuel injection pressure and injector nozzle flow rates. In this regard, an advanced piezo injection system capable of 3000 bar of maximum injection pressure was selected, coupled to a robust base engine featuring ?-shaped combustion bowl and low swirl intake ports. The matching among the above-described elements has been thoroughly examined and experimentally parameterized. The tests confirmed the benefits of the employment of very high fuel injection pressures as a way to decouple the trade-off between an excellent power rating and emissions / NVH / CO2 at part load, whose combination truly defines the leading edge of modern diesel engines for automotive application. The paper also discusses the system sensitivity to the boundary conditions, of the charging and exhaust systems, and develops a balanced set of targets for the entire system based on thermo-structural, fluid-dynamics and efficiency considerations. This would represent, in the authors' view, the 'recipe' for the next generation of premium diesel engines for automotive application

Development trends in modern Common Rail Fuel Injection System (FIS) show dramatically increasing capabilities in terms of optimization of the fuel injection pattern through a constantly increasing number of injection events per engine cycle along with a modulation and shaping of the injection rate. In order to fully exploit the potential of the abovementioned fuel injection pattern optimization, numerical simulation can play a fundamental role by allowing the creation of a kind of a virtual injection rate generator for the assessment of the corresponding engine outputs in terms of combustion characteristics such as burn rate, emission formation and combustion noise (CN). This paper is focused on the analysis of the effects of digitalization of pilot events in the injection pattern on Brake Specific Fuel Consumption (BSFC), CN and emissions for a EURO 6 passenger car 4-cylinder diesel engine. The numerical evaluation was performed considering steady-state conditions for 3 key points representative of typical operating conditions in the low-medium load range. The optimization process was carried out through numerical simulation, by means of a suitable target function aiming to minimize BSFC and CN while not exceeding the target NOx emissions level. By means of a previously developed fuel injection system model, possible different injection patterns with high number of pilot injections were evaluated thus obtaining a kind of virtual injection rate generator, the outcomes of which were then used as input for a DIPulse combustion model in order to predict BSFC, combustion noise and emissions. Through numerical optimization of pilot injection pattern digitalization, potential for achieving significant reductions in BSFC and CN for low load engine points while not exceeding the target NOx emissions level, was demonstrated.

One of the key technologies for the improvement of the diesel engine thermal efficiency is the reduction of the engine heat transfer through the thermal insulation of the combustion chamber. This paper presents a numerical investigation on the effects of the combustion chamber insulation on the heat transfer, thermal efficiency and exhaust temperatures of a 1.6 l passenger car, turbo-charged diesel engine. First, the complete insulation of the engine components, like pistons, liner, firedeck and valves, has been simulated. This analysis has showed that the piston is the component with the greatest potential for the in-cylinder heat transfer reduction and for Brake Specific Fuel Consumption (BSFC) reduction, followed by firedeck, liner and valves. Afterwards, the study has been focused on the impact of different piston Thermal Barrier Coatings (TBCs) on heat transfer, performance and wall temperatures. This analysis has been performed using a 1-D engine simulation code coupled with a lumped mass thermal model, representing the engine structure. A time-periodic wall conduction model has been used to calculate the wall temperature swings along the combustion chamber surface and within the engine cycle. Two different TBC materials, Yttria-Partially Stabilized Zirconia (Y-PSZ) and anodized aluminum, and different layer thicknesses have been simulated.

For a pilot–main injection strategy in a single-cylinder light-duty diesel engine, the dwell between the pilot- and main-injection events can significantly impact combustion noise. As the solenoid energizing dwell decreases below 200 μs, combustion noise decreases by approximately 3 dB and then increases again at shorter dwells. A zero-dimensional thermodynamic model has been developed to capture the combustion noise reduction mechanism; heat release (HR) profiles are the primary simulation input and approximating them as top-hat shapes preserves the noise reduction effect. A decomposition of the terms of the underlying thermodynamic equation reveals that the direct influence of HR on the temporal variation of cylinder pressure is primarily responsible for the trend in combustion noise. Fourier analyses reveal the mechanism responsible for the reduction in combustion noise as a destructive interference in the frequency range between approximately 1 kHz and 3 kHz. This interference is dependent on the timing of increases in cylinder pressure during pilot HR relative to those during main HR. The mechanism by which combustion noise is attenuated is fundamentally different from the traditional noise reduction that occurs with the use of long-dwell pilot injections, for which noise is reduced primarily by shortening the ignition delay of the main injection. Band-pass filtering of measured cylinder pressure traces provides evidence of this noise reduction mechanism in the real engine. When this close-coupled pilot noise reduction mechanism is active, metrics derived from cylinder pressure such as the location of 50% HR, peak HR rates, and peak rates of pressure rise cannot be used reliably to predict trends in combustion noise. The quantity and peak value of the pilot HR affect the combustion noise reduction mechanism, and maximum noise reduction is achieved when the height and steepness of the pilot HR profile are similar to the initial rise of the main HR event. A variation of the initial rise rate of the main HR event reveals trends in combustion noise that are the opposite of what would happen in the absence of a close-coupled pilot. The noise reduction mechanism shown in this work may be a powerful tool to improve the tradeoffs among fuel efficiency, pollutant emissions, and combustion noise.