Search

Input parallel output parallel (IPOP) DC/DC system is widely utilized in many occasions like data center and hybrid electric vehicle (HEV). However, the efficiency characteristics of different converters usually differs from each other, and the conventional control strategy has difficult to realize efficient conversion of overall power of the system. To address this issue, Buck converter is taken as the module and whose efficiency model under current continuous conduction mode (CCM) is presented. Meantime, parameter identification method based on least square (LS) algorithm is proposed as well. In order to realize the efficiency optimization of the whole parallel system, the constraint conditions of each module are analyzed, and the current distribution calculation method based on sequential quadratic programming (SQP) algorithm for the parallel system is introduced. On this basis, a control strategy of proportional current distribution (PCD) is proposed, which not only ensures that the parallel system can always run as efficiently as possible under different loads, but also realizes the flexible switching between the current-sharing mode and current distribution mode. Finally, the simulation and experimental results prove that the proposed method can achieve 4.46% higher efficiency than conventional method within the given power range of each converter, and realize the efficiency optimization of the IPOP DC/DC system to the greatest extent.

To solve motor heating and life shortening of parallel switched reluctance generator (SRG) induced by uneven output currents due to different external characteristics, we generally adopt current sharing control (CSC) to make each parallel generator undertake large load currents on average to improve the reliability of parallel power generation system. However, the method usually causes additional loss of power because it does not consider the efficiency characteristics of each parallel generator. Therefore, with the efficiency expression for the parallel system of SRG established and analysed, the control strategy based on differential evolution (DE) algorithm is proposed as a mechanism by which to enhance generating capacity and reliability of multi-machine power generation from the perspective of efficiency optimisation. We re-adjust the reference current of each parallel generator to transform the working point of each generator and implement the efficiency optimisation of parallel system. The performance of the proposed control method is evaluated in detail by the simulation and experiment, and comparison with traditional CSC is carried out as well.

In this paper, an improved online particle swarm optimization (PSO) is proposed to optimize the traditional search controller for improving the operating efficiency of the permanent magnet synchronous motor (PMSM). This algorithm combines the advantages of the attraction and repulsion PSO and the distributed PSO that can help the search controller to find the optimal d - axis air gap current quickly and accurately under non-stationary operating conditions, thereby minimizing the air gap flux and then improving the motor efficiency. To verify the effectiveness and stability of this proposed algorithm, the operating efficiency of PMSM as using this proposed algorithm is compared with that of traditional search controller under non-stationary operating conditions. The results show that the proposed algorithm can improve the operating efficiency of PMSM by 6.03% on average under non-stationary operation conditions. This indicates that the search controller based on the improved PSO has a better adaptation to the variation of external operating conditions, and can improve the operation efficiency of PMSM under non-stationary condition.

Global maximum power point tracking (GMPPT) refers to the extraction of the maximum power from photovoltaic (PV) modules in real time under changing ambient conditions. Due to the installation of PV systems in densely built-up areas, partial shading scenarios are commonplace. Commercially established GMPPTs suffer from low tracking speeds and inefficiency. A novel GMPPT algorithm is proposed here based on the rectangular power comparison (RPC), which exploits the fundamental relationship between the shading factor, the bypass diode voltage and the global maximum power point. The entire theoretical formulation of RPC is presented systematically for the first time. This method boasts of increased conversion speeds owing to the precomputation of the module voltage versus the shading factor correlations using the regression of diode model from the experimentally obtained bypass diode characteristics. The proposed method is simple to implement with the computational complexity of order $n$ , which represents the number of uniquely shaded PV modules in a series string. The proposed approach addresses the much-needed intersection problem between the distributed and centralized PV systems and therefore targets PV strings which are most common in residential and small to medium scale commercial PV installations world over. The proposed approach is validated with the in-house developed prototype hardware set-up and software control implementation giving a 99% tracking efficiency with a recorded tracking time of 10 ms. The experimental results show 50 times improvement in speed and 95% increase in power gain as compared to the other popular existing methods namely scanning based GMPPT and local MPPT methods respectively, with negligible computational burden and less than 0.5% added cost to the conventional PV energy conversion system.

The equivalent resistance of the battery will change during charging in practical applications, so it is difficult to design a wireless power transfer (WPT) system with accurate constant current (CC) and constant voltage (CV) output characteristics. In addition, the WPT system efficiency is also affected by the change of equivalent resistance. Therefore, this paper studies the charging control and efficiency optimization strategy for the WPT system with dynamic loads. The WPT system with a structure of double-sided LCC compensation topology and containing controllable rectifier circuit at the secondary side is established, and the working process of full-bridge controllable rectifier circuit is analyzed. Then the output characteristics of the WPT system are analyzed. The expressions of the optimal transmission efficiency and the optimal equivalent impedance of the full-bridge rectifier are derived. The relationships between the equivalent impedance of the capacitor-filtered full-bridge controllable rectifier circuit and the phase shift angle, the charging current and the phase shift angle are also obtained. In this paper, the CC and CV charging strategies based on phase shift control of controllable rectifier circuit and efficiency optimization strategy based on dynamic equivalent impedance matching are proposed, which can improve the WPT system transmission efficiency while realizing CC and CV charging. Finally, the effectiveness of the proposed control strategy is verified by simulation and experiment. The WPT system realizes CC charging mode and CV charging mode in turn when the load resistance changes from $5~\Omega $ to $30~\Omega $ , and the overall efficiency is up to 90.71% at the transmission distance of 15cm.

Compensation is key to an inductive power transfer (IPT) system in terms of voltage transfer function and efficiency optimization. Basic compensation is simple, but not suitable, for the achievement of variable load-independent voltage-gains without changing the design of the loosely-coupled transformer (LCT). On the other hand, higher-order compensation circuits enable greater design freedom to achieve variable load-independent voltage-gains while keeping the LCT unchanged, but it requires a variety of compensation components, especially the inductive components, which incur significant copper and core losses. This paper proposes a comprehensive design of the series/series-parallel (S/SP) IPT system. The design methodology for variable load-independent voltage-gains is studied to keep the LCT unchanged and achieve zero phase angle input over the whole load range. Design consideration includes the effect of misalignment issue on the voltage-gain and, thus, a design criteria can be derived to ensure an acceptable sensitivity to the misalignment when taking efficiency optimization. The experimental results are presented for verification.

The paper presents a theoretical analysis of advanced gas-turbine cycles. Specifically, three cycles are investigated, that is the intercooled, the reheat, and the intercooled and reheat cycles. The internal irreversibilities, which characterise the compression and expansion processes, are taken into account through the polytropic efficiencies of the compressors and turbines. New analytical formulations for the overall and intermediate pressure-ratios which maximise the net work of the three aforementioned cycles are proposed along with an order relation between these optimum pressure-ratios. Moreover, the thermal efficiency of these cycles is also analysed providing, among other findings, the ranges of the intermediate pressure-ratios returning a benefit in the thermal efficiency in comparison with the simple cycle. Finally, for the sole intercooled and reheat cycle, a novel analytical expression for the maximum point of the thermal efficiency is given. It is also shown that, for the intercooled and reheat cycle, there is a unique value of the overall pressure-ratio which simultaneously maximises the net work and the thermal efficiency. To give some quantitative information, consider a maximum to minimum cycle-temperature ratio equal to 1573/300 and a compressor (resp. turbine) polytropic-efficiency equal to 0.8 (resp. 0.88). The net work and the thermal efficiency are maximised by a set of overall pressure-ratios obeying an order relation. The simple, the reheat, the intercooled, and the intercooled and reheat cycles reach the maximum net-work (resp. thermal efficiency) for increasing values of the overall pressure-ratio, that is 8.550 (resp. 18.260), 14.950 (resp. 25.039), 20.846 (resp. 39.984), and 73.109 (resp. 73.109). The reheat cycle achieves a 34.899% (resp. 6.077%) gain in the net work (resp. thermal efficiency), while the intercooled cycle returns a 31.477% (resp. 15.970%) increment. The maximum net-work of the intercooled and reheat cycle exactly doubles that of the simple cycle. Finally, the maximum thermal efficiency of the intercooled and reheat cycle yields a 24.966% improvement in comparison with the simple one.

The efficiency of asynchronous motor is higher near the rated working point, but it will decrease significantly under light load. A hybrid search method is proposed to optimize the efficiency of asynchronous motor drive by current source at the light load operating condition. The approximate optimal flux is obtained according to the loss model method and the convergence speed is determined by the golden section method. Hybrid optimization control method has the advantages of fast response and global optimization of efficiency without relying on motor parameters. It not only shortens the search time but also effectively reduces the system loss. The control system stability is higher and the optimization performance has been significantly improved. The simulation results show that the hybrid search method has the advantages of fast optimization speed and good robustness. Especially under the condition of light load, the motor efficiency can be obviously improved.

This paper proposes a triple phase shift modulation with an optimization technique that aims at maximizing the efficiency of the Dual Active Bridge (DAB) converter. The DAB converter finds application in smart dc power systems, including the electrification of the powertrain of vehicles and vehicles-togrid applications, where loss minimization is crucial. In this paper, favorable modulation parameters are found first, by aiming at minimum rms currents and zero voltage switching (ZVS) for the converter switches. Then, on the basis of the closed-form analytical description of the converter behavior over the determined favorable modulation patterns, efficiency improvement trajectories in the modulation planes are identified. It is shown that such trajectories lead to optimal efficiency operation, which can be exploited to implement fast closedloop efficiency optimization methods. The reported results are verified experimentally on a 1.5 kW prototype, showing that the proposed approach allows to achieve the best-efficiency operation of the converter.

Optimizing the natural frequency is crucial for dc-to-load efficient wireless power transfer (WPT) applications on high voltage (HV) power transmission lines. However, a comprehensive optimization approach with the coupling factor and the losses on power electronics both taken into consideration is still in absence. By modeling losses dissipated on various parts, including the class-D inverter, the rectifier, and the resonant loops, a numerical approach is proposed in this paper to evaluate the optimal natural frequency for maximum dc-to-end efficiency. As the system efficiency is also affected by the operating frequency, which is resilient for practical operation, practical operating strategies are applied to determine the working parameters. Furthermore, considering that the HV WPT systems may work with various coupling factors, optimal natural frequencies for various coupling factors are analyzed and compared. Several groups of experiments are conducted to verify the effectiveness of the proposed numerical approach. Experimental results show that the approach can effectively predict the optimal natural frequency. When compared with the cases where the natural frequency is 100 or 600 kHz, an efficiency enhancement of about 20% can be achieved using the optimized natural frequency. When compared with the cases where the natural frequency is optimal for maximum $Q$ value, an efficiency of 9% can still be achieved for loosely coupled occasions.

Bidirectional wireless power transmission (BD-WPT) systems are applicable to occasions that need bidirectional energy flows, such as vehicle-to-grid technology. The traditional BD-WPT systems work at a fixed frequency and the optimal transmission efficiency of the systems is fixed. Combining the frequency characteristics of AC resistance, the mathematical model of variable frequency BD-WPT system is built in this paper. Then, the characteristics of transmission efficiency and the characteristics of maximum active power are analyzed based on the model. In order to make the BD-WPT system have higher transmission efficiency, a BD-WPT system with variable structural parameters and the corresponding segmented power-efficiency coordinated control strategy are proposed in this paper. According to different reference power on the secondary side, the BD-WPT system can work in different resonant frequency segments by controlling the switching of corresponding relays in the capacitor arrays on the primary and secondary sides and changing working frequency of the H-bridge converters on the primary and secondary sides. By using the proposed control strategy, the transmission power, and direction, can be tunable segmentally while maintaining high transmission efficiency. The proposed concept is verified to be effective through experiment.

This paper proposes an efficiency optimization method for the permanent magnet synchronous motor (PMSM) based powertrain by using field-circuit coupled finite-element method (FEM) for electric vehicle or hybrid electric vehicle applications. In this paper, an alterable flux-weakening (FW) angle is employed in the armature current control strategy for the FW operation. The optimal FW angle for each certain operating condition can be obtained through the pre-selection, which improves the system efficiency compared to conventional FW methods. Then, the lookup table (LUT) for optimal armature current control commands is obtained. Through using this optimal LUT in the drive system, the system efficiency can be significantly improved for the entire operation range. The time-stepping FEM is used to simulate the PMSM system, which integrates the electromagnetic field analysis of the motor prototype and the control algorithm of the drive system. A 2-D transient FEM model is built for a 15 kW PMSM in ANSYS Maxwell, and a vector control circuit model is set up in ANSYS Simplorer. Experiments are carried out on the 15 kW PMSM prototype to verify the accuracy of the simulation results and the effectiveness of the proposed design method.

In the agricultural and work machine sectors, hydromechanical transmission competes with traditional mechanical transmission. However, the double energy conversion taking place in hydrostatic transmission lowers the efficiency of the entire transmission. Thus, the dimensioning of hydromechanical transmission must not only meet the functional requirements of speed and power to be transmitted, but must also identify the particular combination of layout and the components that leads to the maximum efficiency. In this study, a general answer to this problem will be given. The design is transformed into a mathematical programming problem, whose goal is the optimisation of both the configuration and internal components of the transmission. The structure of the transmissions is described by means of graph theory, and the resolution of the optimisation problem is obtained by means of a ‘direct search’ algorithm based on the swarm method.

This paper presents experimental studies on the optimization of two-phase fluid flow in an airlift pump. Airlift pumps, also known as mammoth pumps, are devices applied for vertical transport of liquids with the use of gas. Their operating principle involves the existence of a density gradient. This paper reports the results of experimental studies into the hydrodynamic effects of the airlift pump. The studies involved optical imaging of two-phase gas-liquid flow in a riser pipe. The visualization was performed with high-speed visualization techniques. The studies used a transparent model of airlift pump with a rectangular cross-section of the riser. The assessment of the airlift pump operation is based on the image grey-level analysis to provide the identification of two-phase flow regimes. The scope of the study also involved the determination of void fraction and pressure drops. The tests were carried out in a channel with dimensions 35 &times, 20 &times, 2045 mm with the gas flux range 0.2&ndash, 15.0 m3/h. For the assessment of the two-phase flow pattern Probability Density Function (PDF) was applied. On the basis of the obtained results, a new method for selecting the optimum operating regime of airlift pump was derived. This method provides the finding of stability and efficiency of liquid transport. It can also be applied to determine the correlation between the total lifting efficiency and the required gas flux for proper operation of the airlift pump.

Radio waves carry both energy and information simultaneously. Nevertheless, Radio-Frequency (RF) transmission of these quantities have traditionally been treated separately. Currently, we are experiencing a paradigm shift in wireless network design, namely unifying wireless transmission of information and power so as to make the best use of the RF spectrum and radiations as well as the network infrastructure for the dual purpose of communicating and energizing. In this paper, we review and discuss recent progress on laying the foundations of the envisioned dual purpose networks by establishing a signal theory and design for Wireless Information and Power Transmission (WIPT) and identifying the fundamental tradeoff between conveying information and power wirelessly. We start with an overview of WIPT challenges and technologies, namely Simultaneous Wireless Information and Power Transfer (SWIPT),Wirelessly Powered Communication Network (WPCN), and Wirelessly Powered Backscatter Communication (WPBC). We then characterize energy harvesters and show how WIPT signal and system designs crucially revolve around the underlying energy harvester model. To that end, we highlight three different energy harvester models, namely one linear model and two nonlinear models, and show how WIPT designs differ for each of them in single-user and multi-user deployments. Topics discussed include rate-energy region characterization, transmitter and receiver architecture, waveform design, modulation, beamforming and input distribution optimizations, resource allocation, and RF spectrum use. We discuss and check the validity of the different energy harvester models and the resulting signal theory and design based on circuit simulations, prototyping and experimentation. We also point out numerous directions that are promising for future research., guest editor-authored tutorial paper submitted to IEEE JSAC special issue on wireless transmission of information and power

A variable bus voltage DC microgrid (MG) is simulated in Simulink for optimization purposes. It is initially controlled with a Voltage Event Control (VEC) algorithm supplemented with a State of Charge Event Control (SOCEC) algorithm. This control determines the power generated/consumed by each element of the MG based on bus voltage and battery State of Charge (SOC) values. Two supplementary strategies are proposed and evaluated to improve the DC-DC converters’ efficiency. First, bus voltage optimization control: a centralized Energy Management System (EMS) manages the battery power in order to make the bus voltage follow the optimal voltage reference. Second, online optimization of switching frequency: local drivers operate each converter at its optimal switching frequency. The two proposed optimization strategies have been verified in the simulations.

In a battery-electric vehicle, a representative electric vehicle, there is a growing demand for performance and one-charge mileage improvement. As an alternative to such improvements, the capacity of the battery has been increased; however, due to the corresponding increase in the weight of the battery and the limited space in the vehicle, increasing the capacity of the battery also has limitations. Therefore, researches are being actively conducted to improve system operation efficiency to overcome such limitations. This paper proposes a distributing method of the driving forces to a battery-powered electric shuttle bus for last-mile mobility equipped with the decentralized driving system while taking into account voltage changes of the input terminals due to changes in the battery charge. The system operation efficiency changes were compared and evaluated by performing energy consumption analysis using ‘Manhattan Bus Driving Cycle’ at low voltage condition (SOC 20%). Various analyzes were performed and compared, such as the uniform distribution method of driving forces of the front and rear wheels (Uniform), the optimization method without considering the input terminal voltage change (Vnorm = 90 V), and the optimization method considering the input terminal voltage change (Vdclink). As a result, it shows that the proposed algorithm can improve 6.0% compared to the conventional uniform driving force distribution method (Uniform). Moreover, it shows that the real-time optimization method without considering the input voltage change (Vnorm = 90 V) can improve 5.3% compared to the uniform distribution method. The proposed method can obtain an additional 0.7% increase in total cost compared to the existing optimization method, which shows that the vehicle system has cost-effectiveness by reducing the battery capacity required to achieve the same mileage.

The global share of photovoltaic plants in desert locations increases continuously due to inexpensive land and higher yield due to higher irradiation levels. However, PV modules suffer from harsh environmental conditions that influence their lifetime and, consequently, the levelized cost of electricity. Environmental factors such as high temperature differences between nights and days, high ultraviolet doses, high ambient temperatures, and high airborne dust lead to durability and performance issues such as delamination, discoloration, fatigue of interconnection, breakage of solar cells, hot-spots, and power loss due to the soiling. In this work, different bills of materials and module designs are evaluated, targeting optimum PV output power while increasing the service life and performance of the PV modules in desert climates. A stepwise optimization of module components (solar cells, glass coating and polymers/encapsulation) and module design (full vs. half cells, tab widths) are performed by simulation and experimental approaches. Simulations results analyzes the loss mechanisms and electricity production of PV modules by considering the impact of module material and design Experimentally, ultraviolet stress tests and thermal cycling tests are performed for polymer durability and interconnection fatigue analysis. The soiling reduction potential of a newly developed glass coating is investigated by outdoor exposure tests in Saudi-Arabia. It is shown by proper choice of materials and optimized interconnection design, the efficiency of the module is increased by 9.58%rel. relative to the reference module. Furthermore, the choice of encapsulant and module design strongly affect the expected service-life, and soiling losses could be reduced up to 35%.

© 1982-2012 IEEE. Aiming to improve the performance features of conventional two-level dual-active-bridge (DAB) converters, this paper presents a three-level neutral-point-clamped (NPC) DAB dc-dc converter. A general modulation pattern is initially defined, the dc-link capacitor voltage balancing is analyzed in detail, and a proper balancing control is designed. Then, a set of decoupled optimization problems is formulated as a function of the available modulation degrees of freedom to minimize the predominant converter losses. Finally, a simple and practical specific modulation strategy is provided, resembling the optimum solutions. The good performance of the proposed three-level NPC DAB converter operated with the proposed modulation strategy and voltage balancing control is verified through simulation and experiments. The capacitor voltage balancing can be guaranteed for all operating conditions. In addition, it is concluded that the multilevel topology provides benefits compared with the conventional two-level DAB converter.

The combination of permanent magnet synchronous motor (PMSM) and inverter is the key electric drive system (EDS) of electric vehicles (EVs), and its overall efficiency seriously affects the energy consumption of EVs. In order to further improve the efficiency of PMSM-inverter, the influence of a special control object current angle &beta, on EDS was studied and the general rule between &beta, and EDS efficiency was obtained in this paper. Then, the golden section search (GSS) method was used to obtain optimal &beta, and its corresponding stator current is, which can realize EDS working in optimal efficiency in the whole EDS working area. On this basis, an overall efficiency optimization control strategy for EDS based on the current angle &beta, look-up table was proposed in this paper. To verify the effectiveness of the proposed control strategy, simulation considering iron loss and copper loss of motor and inverter loss was completed, which showed that compared with traditional control, the control strategy proposed in this paper can effectively improve the working efficiency of EDS under steady state and transient state.

International audience; We investigate the interaction of linear surface waves with a submerged wave energy converter which consists of a submerged flexible plate actuated by one (or more) units of power take off (PTO), each modeled as a combination of a linear spring and a linear damper. We develop a wave-flexible structure interaction model through modal decomposition of the structure deformations, and use Boundary Element Method to find hydrodynamic coefficients of each deformation mode of the structure. We validate our methodology with existing analytical results of hydro-elasticity. We then perform a case study and obtain the maximum efficiency (or Capture Width Ratio (CWR)) of our wave energy converter whenexcited by monochromatic waves through a comprehensive parametric study of the device parameters (e.g. rigidity of the plate, and location and characteristics of the PTO units). In the absence of viscous effects, the device can reach an efficiency as high as 80%. We find that the efficiency is more sensitive to the location of the PTOs than to their damping coefficients. For a range of plate length to wavelength ratios (close to unity) and with a single PTO unit, the optimal PTO location is past the middle of the plate (along the incident wave direction). This location is nearly independent of the rigidity of the plate although the resulting CWR depends on the rigidity. When two PTO units are used the optimal configuration of PTOs depends on the plate’s aspect ratio and its placement with respect to the incident wave: the two PTOs may need to be at the same location, lined up along the direction of wave propagation, or placed side-by-side perpendicular to the direction of the wave propagation.

MINAZ, Mehmet Recep/0000-0001-8046-6465; toren, murat/0000-0002-7012-7088; Ghaderi, davood/0000-0003-2234-3453 WOS: 000436583500003 So as to keep the converter in small size, high switching frequencies are normally used. As a result, in higher frequencies, switching losses seriously affect the efficiency. Current and voltage stresses on power switch can be serious problems particularly in high amount of powers where MOSFET switches are generally applied. A snubber circuit can reduce or eliminate spike voltage and currents, decrease the di/dt or dv/dt values on power switch and transfer the power losses on switch to load and increases the lifelong of the switch. This study presents a method for improving the power transmission efficiency for DC-DC Cascaded Boost Converter and uses a passive snubber sub-circuit, which consists of an inductor, a capacitor, and two diodes for reducing the switching loss. the role of resonant capacitor of this structure is discharging directly through the load and is parallel with the power switch. Thus, it is effective in lossless switching and increasing the DC voltage gain of the boost converter. Soft switching is achieved through the use of a LC resonant tank circuit. the tank circuit is responsible for zero voltage switching (ZVS) and zero current switching (ZCS), eliminating the power loss in the switches appreciably. the proposed structure, done by MATLAB SIMULINK based on simulations, has shown more efficiency toward the same structure without snubber circuit. Besides, an application has been conducted in laboratory scales, and results confirm theoretical findings.

To improve the endurance mileage of electric vehicles (EVs), it is important to decrease the energy consumption of the Permanent Magnet Synchronous Motor (PMSM) drive system. This paper proposes a novel loss optimization control strategy named system efficiency improvement control which can optimize both inverter and motor losses. A nonlinear power converter loss model is built to fit the nonlinear characteristics of power devices. This paper uses double Fourier integral analysis to analytically calculate the fundamental and harmonic components of motor current by which the fundamental motor loss and harmonic motor loss can be accurately analyzed. From these loss models, a whole-frequency-domain system loss model is derived and presented. Based on the system loss model, the system efficiency improvement control method applies the genetic algorithm to adjust the motor current and PWM frequency together to optimize the inverter and motor losses by which the system efficiency can be significantly improved without seriously influence on the system stability over the whole operation range of EVs. The optimal effects of system efficiency is verified by the experimental results in both Si-IGBT-based PMSM system and SiC-MOSFET-based system.

Nowadays environmental concerns call for a transition towards an economy based on fossil fuels to a low carbon one. In order to achieve this goal, efficiency optimization of existing energy systems through waste heat to power conversion units based on bottoming Organic Rankine Cycles (ORC) is one of the actions that appears to be suitable and effective both from cost and environmental perspectives. Indeed, these units are able to increase the overall efficiency of production processes, existing facilities and renewable power plants with a limited payback time. However, despite the increasing number of ORC installations at megawatt scale, the waste heat rejected by industrial processes has rather a widespread nature. Hence, ORC units with a power output in the range of kilowatts should be developed to address this opportunity for heat recovery and for business. In the current research activity, a dynamic model of an ORC system was developed in a commercial 1D Computer Aided Engineering software platform. Sub-models of the two plate heat exchangers and of the multi-stage centrifugal pump were developed and calibrated using performance data of industrial components at design and off-design conditions. On the other hand, the R245fa radial turbine design was accomplished using a design procedure that provided geometrical and performance data for the mapping of the device by means of a 1D tool. A steady-state off-design analysis at different operating conditions at the evaporator was further carried out optimizing pump and turbine speeds to maximize the net power output. Furthermore, the thermal inertial effects at the evaporator were assessed with reference to a sample heat load profile of the water hot source and at different time scales. The authors would like to acknowledge funding from Research Council UK (RCUK), Grant No. EP/K011820/1.

As is common in multi-load wireless power transfer (WPT) systems based on series&ndash, series compensation topology, the power received by loads and the efficiency of the process are highly sensitive to changes in the number of loads. To guarantee that the power supplied to a load remains stable when other loads access or leave the system, we propose an improved multi-load system for WPT. The new system uses an LCC/S topology (based on inductor&ndash, capacitor&ndash, inductor or LCL topology) to keep the power received by the loads stable. By comparing two scenarios (ideal and real models based on LCC/S topology), we aim to eliminate cross-coupling between receiving coils by connecting compensating capacitors in series on the receiving side. In this way, the stability of the power received by loads is further improved. Moreover, a method of optimizing control over the efficiency is proposed based on the effect on the overall efficiency of impedance and number of loads. This allows us to optimize the overall efficiency of the system. Finally, a system to verify our theoretical analysis is established and used to show the validity and effectiveness of the proposed system.