Search

Two-dimensional (2D) Ruddlesden-Popper perovskites (RPPs) of the form PEA2Pb1-xSnxI4 can be used as the tunable active layer in photovoltaics, as the passivating layer for 3D perovskite photovoltaics or in light emitting diodes. Here, we show a nonlinear band gap behavior with Sn content in mixed phase 2D RPPs. Density functional theory calculations (with and without spin-orbit coupling) are employed to study the effects of the short-range ordering of Pb and Sn in PEA2Pb1-xSnxI4 compositions with x = 0, 0.25, 0.5, 0.75, and 1. Analysis of the partial density of states shows that the energy mismatch of the Pb 6s and Sn 5s states in the valence band maximum determines the nonlinearity of the band gap, leading to a bowing parameter of 0.35-0.38 eV. This research provides a critical insight for the design of future metal alloy 2D perovskite materials. The positions of the tunable energy band discontinuity may point to intraband transitions of interest to device engineers.

Made available in DSpace on 2021-06-25T10:29:39Z (GMT). No. of bitstreams: 0 Previous issue date: 2021-04-28 Typically used semiconducting metal oxides (SMOs) consist of several varying factors that affect gas sensor response, including film thickness, grain size, and notably the grain-grain junctions within the active device volume, which complicates the analysis and optimisation of sensor response. In comparison, devices containing a single nanostructured element do not present grain-grain junctions, and therefore present an excellent platform to comprehend the correlation between nanostructure surface stoichiometry and sensor response to the depletion layer (Debye length,LD) variation after the analyte gas adsorption/chemisorption. In this work, nanofabricated devices containing SnO2and Sn3O4individual nanobelts of different thicknesses were used to estimate theirLDafter NO2exposure. In the presence of 40 ppm of NO2at 150 °C,LDof 12 nm and 8 nm were obtained for SnO2and Sn3O4, respectively. These values were associated to the sensor signals measured using multiple nanobelts onto interdigitated electrodes, outlining that the higher sensor signal of the Sn4+surface (up to 708 for 100 ppm NO2at 150°) in comparison with the Sn2+(up to 185) can be explained based on a less depleted initial state and a lower surface electron affinity caused by the Lewis acid/base interactions with oxygen species from the baseline gas. To support the proposed mechanisms, we investigated the gas sensor response of SnO2nanobelts with a higher quantity of oxygen vacancies and correlated the results to the SnO system. Advanced Technology Institute Dept. of Electrical & Electronic Engineering University of Surrey Department of Engineering Physics and Mathematics São Paulo State University (UNESP) Araraquara Department of Engineering Physics and Mathematics São Paulo State University (UNESP) Araraquara

Ruddlesden–Popper phase (RPP) perovskites of the form A1n−1A22BnX3n+1 show great promise in stable photovoltaic (PV) devices or as light emitting diodes (LEDs). In particular, n = 1, monolayer RPPs of the form A2BX4 have also shown great progress as the passivating layer for 3D perovskite PVs. We study the electronic behaviour of mixed B site A2Pb1−xSnxI4 where A = PEA or MA to investigate if the size of the A site cation indirectly affects the nonlinear band gap dependence of a 2D monolayer RPP layer. Both perovskites show a nonlinear behaviour primarily due to the relative energy difference between the Sn 5s–I 5p antibonding states and the Pb 6s–I 5p antibonding states, though the extent of the nonlinearity is reduced relative to 3D bulk perovskites due to the reduced dimensionality of these 2D structures. We also discuss the influence on band gap nonlinearity due to the structural distortions induced by the differences between the A site cation. This research presents a strategy to the design of mixed solid state 2D perovskites by tuning the structural parameters as well as metal and halide composition.

Modern integrated devices and electrical circuits have often been designed with carbon nanostructures, such as carbon nanotubes (CNTs) and graphene due to their high thermal and electrical transport properties. These transport properties are strongly correlated to their acoustic phonon and carrier dynamics. Thus, understanding the phonon and carrier dynamics of carbon nanostructures in extremely small regions will lead to their further practical applications. Here, we demonstrate ultrafast time-resolved electron diffraction and ultrafast transient spectroscopy to characterize the phonon and carrier dynamics at the boundary of quasi-one-dimensional CNTs before and after Joule annealing. The results from ultrafast time-resolved electron diffraction show that the CNTs after Joule annealing reach the phonon equilibrium state extremely fast with a timescale of 10 ps, which indicates that thermal transport in CNTs improves following Joule annealing. The methodology described in this study connects conventional macroscopic thermo- and electrodynamics to those at the nanometer scale. Realistic timescale kinetic simulations were performed to further elaborate on the phenomena that occur in CNTs during Joule annealing. The insights obtained in this study are expected to pave the way to parameterize the unexplored thermal and electrical properties of carbon materials at the nanometer scale.

Perovskite solar cells (PSCs) have emerged as a ‘rising star’ in recent years due to their high-power conversion efficiency (PCE), extremely low cost and facile fabrication techniques. To date, PSCs have achieved a certified PCE of 25.2% on rigid conductive substrates, and 19.5% on flexible substrates. The significant advancement of PSCs has been realized through various routes, including perovskite composition engineering, interface modification, surface passivation, fabrication process optimization, and exploitation of new charge transport materials. However, compared with rigid counterparts, the efficiency record of flexible perovskite solar cells (FPSCs) is advancing slowly, and therefore it is of great significance to scrutinize recent work and expedite the innovation in this field. In this article, we comprehensively review the recent progress of FPSCs. After a brief introduction, the major features of FPSCs are compared with other types of flexible solar cells in a broad context including silicon, CdTe, dye-sensitized, organic, quantum dot and hybrid solar cells. In particular, we highlight the major breakthroughs of FPSCs made in 2019/2020 for both laboratory and large-scale devices. The constituents of making a FPSC including flexible substrates, perovskite absorbers, charge transport materials, as well as device fabrication and encapsulation methods have been critically assessed. The existing challenges of making high performance and long-term stable FPSCs are discussed. Finally, we offer our perspectives on the future opportunities of FPSCs in the field of photovoltaics.

Maintaining structural stability and alleviating the intrinsic poor conductivity of cathode materials are of great importance for practical application of Li–S batteries. Introducing void space and a highly conductive host to accommodate the volume changes and enhance the conductivity would be a smart design to achieve robust construction; effective electron and ion transportation, thus, lead to prolonged cycling life and excellent rate performance. In this regard, we report the design of carbonaceous hybrid with vertically aligned graphene assembled on multi-yolk/shell structured TiC@C nanofibers to afford synergistic properties of enough space, strong chemisorption and active electrocatalysis, high electrical conductivity as a sulfur host. Thus, the as-prepared sulfur cathode delivers an excellent cyclability over 800 cycles, a high areal capacity of 6.81 ​mA ​h ​cm2 at a high sulfur loading (10.5 ​mg). More importantly, soft package battery was also prepared with a capacity of 530 ​mAh g−1 and 46.5 ​mAh in the first cycle at a sulfur loading of 4.5 ​mg ​cm−2, which reveals its potential in promoting the practical application of Li–S batteries.

A carbon fiber microstrip patch antenna is presented, constructed entirely from fiber-reinforced plastic materials, and fabricated directly into carbon-fiber-reinforced plastic (CFRP) composites as part of the composite manufacturing process. Fabrication of antennas as part of the composite manufacturing process provides numerous benefits, such as conformation to complex curvatures, reduced weight, and reduced aerodynamic impact. Modification of the localized conductivity of the carbon fiber using materials such as copper meshes is shown to improve the gain of the antenna by as much as 5 dB, while also improving the interlaminar shear strength of the composite by 22%.

Carbon nanotubes (CNTs) have gained much interest from academia and industry due to their unique properties that include high electrical and thermal conductivity, high mechanical strength, high aspect ratio, high surface area and chemical resistance. Although composite structures containing CNTs are probably the most commercially advanced applications in the market, the area that holds most promise is in electronic applications. Low temperature CVD growth of high quality CNTs can be utilized in many applications particularly next generation IoTs, wearable electronic devices, TSVs, interconnects, and sensors. CNT growth temperature generally reported in literature ranges from 600 – 1000oC, which is not suitable for temperature sensitive substrates. However, there is ongoing research to achieve CNT growth at low temperatures, with a number reporting the growth below 550oC. In this review, we examine and discuss various techniques and approaches adopted to achieve growth of carbon nanotubes at low temperatures and its effect on various parameters of CNTs.

Curved X‐ray detectors have the potential to revolutionize diverse sectors due to benefits such as reduced image distortion and vignetting compared to their planar counterparts. While the use of inorganic semiconductors for curved detectors are restricted by their brittle nature, organic–inorganic hybrid semiconductors which incorporated bismuth oxide nanoparticles in an organic bulk heterojunction consisting of poly(3‐hexylthiophene‐2,5‐diyl) (P3HT) and [6,6]‐phenyl C71 butyric acid methyl ester (PC70BM) are considered to be more promising in this regard. However, the influence of the P3HT molecular weight on the mechanical stability of curved, thick X‐ray detectors remains less well understood. Herein, high P3HT molecular weights (>40 kDa) are identified to allow increased intermolecular bonding and chain entanglements, resulting in X‐ray detectors that can be curved to a radius as low as 1.3 mm with low deviation in X‐ray response under 100 repeated bending cycles while maintaining an industry‐standard dark current of, Solution processable organic–inorganic hybrid semiconductors for flexible curved X‐ray detector components have the potential to revolutionize diverse sectors in terms of its cost and performance. This work introduces a strategy for realizing the optimum balance for detector performance at low operating voltages with mechanical flexibility by tuning the organic semiconductor molecular weight for such curved hybrid detectors.

Hybrid inorganic-in-organic semiconductors are an attractive class of materials for optoelectronic applications. Traditionally, the thicknesses of organic semiconductors are kept below 1 μm due to poor charge transport in such systems. However, recent work suggests that charge carriers in such organic semiconductors can be transported over centimeter length scales opposing this view. In this work, a unipolar X-ray photoconductor based on a bulk heterojunction architecture, consisting of poly(3-hexylthiophene), a C70 derivative, and high atomic number bismuth oxide nanoparticles operating in the 0.1–1 mm thickness regime is demonstrated, having a high sensitivity of ∼160 μC mGy–1 cm–3. The high performance enabled by hole drift lengths approaching a millimeter facilitates a device architecture allowing a high fraction of the incident X-rays to be attenuated. An X-ray imager is demonstrated with sufficient resolution for security applications such as portable baggage screening at border crossings and public events and scalable medical applications.

A facile hydrothermal process is used to prepare hybrid graphene-MoO3 particles to be used as hole transport layers (HTLs) in organic solar cells (OSCs). The OSCs with active layer donor/acceptor combinations of Poly[N-9″-hepta-decanyl-2,7-carbazolealt-5,5-(4′,7′-di-2-thienyl-2′,1′,3′-benzothiadiazole)] (PCDTBT) and fullerene derivative [6,6]-phenyl-C71-butyric acid methylester (PC71BM) exhibit an enhanced power conversion efficiency (PCE) of 7.07%, an increase by 19% with the hybrid HTL compared to those devices with only MoO3 HTLs. Through investigating the optical and electrical properties of the devices, we found that the superior PCE originates from an enhanced hole transport property resulting from the extraction capabilities of G-MoO3. Comparing with thermal evaporated MoO3, the G-MoO3 exhibits a higher optical transmittance, improved electrical conductivity and enhanced hole mobility. Moreover, the work function of the hybrid G-MoO3 was close to the highest occupied molecular orbital (HOMO) level of PCDTBT, which reduced the energy barrier for the carriers and was suited for hole transport.

An efficient polymer solar cell (PSC) has been demonstrated by incorporating an ultrathin interfacial insulating organic layer of polytetrafluoroethylene (PTFE) between a photoactive layer and hole-collecting buffer layer (NiOx). The photoactive layer is made with bulk heterojunction composites of poly[N-9’’-hepta-decanyl-2,7-carbazolealt-5,5-(4′,7′-di-2-thienyl- 2′,1′,3′-ben-zothiadiazole)]:[6,6]-phenyl-C71-butyric acid methyl ester (PCDTBT:PC71BM). The PTFE layer not only improves the energy level alignment by forming an interfacial dipole at the interface but also reduces the inherent incompatibility between the hydrophobic active layer and hydrophilic NiOx layer, thereby benefiting to the charge extraction and transport in the solar cells. As a result, with the NiOx/PTFE stacked structure, all the photovoltaic performance parameters are significantly improved, leading to a higher power conversion efficiency (PCE) of up to 7.11% compared to the control device without PTFE layer (PCE 5.50%). The PTFE layer provides a superior alternative to interfacial engineering of the metal oxide/organic semiconductor interface in polymer solar cells and other organic electronic devices.

Polymer solar cells (PSCs) are considered promising energy power suppliers due to their light weight, printability, low-energy fabrication and roll-to-roll processability. Recently, the solution-processed NiOx nanoparticles have been a desirable interfacial material for hole transport in the PSCs, instead of organic semiconductors. However, pure NiOx films restrain the high performance of PSCs due to their poor electrical characteristics caused by the localized orbital distribution at the top of valence band. Therefore, metal ion doping has been explored as a method to endow NiOx nanoparticles with the appropriate electrical characteristics. Herein, we applied solution-processed Cu-doped NiOx (Cu:NiOx) nanoparticles as an efficient hole transport layer (HTL) in PSCs. The Cu-doped NiOx enhanced the electrical conductivity of the material and improved the interface contact with the active layer, which remarkably facilitated the hole extraction and effectively suppressed the carrier recombination at the interface. Thus, a higher power conversion efficiency of 7.05%, corresponding to an approximately 30% efficiency improvement compared with that of a pristine NiOx interlayer (5.44%) in poly[N- 9''-hepta-decanyl-2,7-carbazolealt-5,5-(4',7'-di-2-thienyl-2',1',3'-ben-zothiadiazole)]:[6,6]-phenyl-C71-butyric acid methyl ester (PCDTBT:PC71BM)-based PSCs, was achieved by the proposed device. The developed solution-processed Cu:NiOx nanoparticles may be an excellent alternative for interfacial materials in PSCs or other optoelectronic devices requiring HTLs.

To develop high performance nanocomposites with potential commercialization value, general synthesis strategies that could provide nanocomposites with finely tunable nanostructures and physicochemical properties are desirable. In this work, a universal approach was developed that fulfilled these requirements for the sequential growth of nitrogen-doped carbon-molybdenum disulfide (denoted as NC-MoS2) nanocomposites with versatile nanostructures, namely, dual–shell, yolk–shell, core–shell, hollow spheres and nanorods. The formation mechanism of the different nanostructures is proposed to arise from the synergistic effect of dual surfactants, the complexing effect between amine groups and Mo species, hydrogen bonding interactions among aminophenol resols, cysteine and sodium molybdate dihydrate (Na2MoO4·2H2O), and the sequential formation of Mo-resol clusters. The NC-MoS2 hollow spheres displayed higher lithium-ion storage capacity than the N-free hollow sample, NC-MoS2 dual–shell and yolk–shell spheres, and may benefit from the strengthened charge transfer rate originating from the N-doping, higher N-content and hollow nanostructures.

In this work we investigate the influence of thermal treatment of reduced graphite oxide (RGO) on its functional composition and electrochemical performance. It is found that carboxyl, carbonyl, hydroxyl and epoxy groups are present on the RGO surface, witch when subject to thermal annealing in the temperature range 230-250°C can be controllably modified. In the process of thermal annealing, we show the formation of quinoid groups due to an increase in the number of defects. Decrease of the number of layers in RGO material and the quantity of oxygen-containing functional groups (OCFG) also occurs. With increase in annealing temperature, sequential removal of OCFG occurs as follows: carboxyl (250°C-600°C), hydroxyl (600°C-800°C), carbonyl and quinoid (700°C-1000°C). Electrochemical measurements over a wide range of pH values of the buffer electrolytes is possible to correlate the peaks in the cyclic voltammogram curves with the redox reactions of oxygen-containing functional groups as a function of applied potential. Peaks correlated with specific redox reactions which are identified as two-electron. The dependence of the specific capacities of materials on the electrolyte type has been studied. Highest capacitance was detected in 1M NaOH at a scan rate 2 mVs−1 and is equal to 210 Fg−1.

With the realization of larger and more complex space installations, an increase in the surface area exposed to atomic oxygen (AO) and ultraviolet (UV) effects is expected, making structural integrity of space structures essential for future development. In a low Earth orbit (LEO), the effects of AO and UV degradation can have devastating consequences for polymer and composite structures in satellites and space installations. Composite materials such as carbon fiber-reinforced polymer (CFRP) or polymer materials such as polyetherimide and polystyrene are widely used in satellite construction for various applications including structural components, thermal insulation, and importantly radio frequency (RF) assemblies. In this paper, we present a multilayered material protection solution, a multilayered protection barrier, that mitigates the effects of AO and UV without disrupting the functional performance of tested assemblies. This multilayered protection barrier deposited via a custom-built plasma-enhanced chemical vapor deposition (PECVD) system is designed so as to deposit all necessary layers without breaking vacuum to maximize the adhesion to the surface of the substrate and to ensure no pinhole erosion is present. In the multilayer solution, a moisture and outgassing barrier (MOB) is coupled with an AO and UV capping layer to provide complete protection.

Organic-inorganic halide perovskite solar cells (PSCs) have shown a significant growth in power conversion efficiencies (PCEs) during last decade. Progress in device architecture and high-quality perovskite film fabrication has led to an incredible efficiency over 25% in close to a decade. Developments in solution-based thin film deposition techniques for perovskite layer preparation in PSCs provide low cost and ease of process for their manufacturing, making them a potential contender in future solar energy harvesting technologies. From small area single solar cells to large area perovskite solar modules, solvents play crucial roles in thin film quality and therefore, the device performance and stability. A comprehensive overview of solvent engineering toward achieving the highest qualities for perovskite light absorbing layers with various compositions and based on different fabrication processes is provided in this review. The mechanisms indicating the essential roles a solvent, or a solvent mixture can play to improve the crystallinity, uniformity, coverage and surface roughness of the perovskite films, are discussed. Finally, the role of solvent engineering in transferring from small area laboratory scale PSC fabrication to large area perovskite film deposition processes is explored.

The electron-phonon interaction controls the intrinsic mobility of charges in metal halide perovskites, and determines the rate at which carriers lose energy. Here, the carrier mobility and cooling dynamics were directly examined using a combination of ultrafast transient absorption spectroscopy and optical pump, THz probe spectroscopy, in perovskites with different lead and tin content, and for a range of carrier densities. Significantly, the carrier mobility in the ``hot phonon bottleneck'' regime, where the LO phonon bath keeps carriers warm, was found to be similar to the mobility of cold carriers. A model was developed that provides a quantitative description of the experimental carrier cooling dynamics, including electron-phonon coupling, phonon-phonon coupling and the Auger mechanism. In the Pb and Sn alloy the duration of the hot carrier regime was extended as a result of the slower decay of optical phonons. The findings offer an intuitive link between macroscopic properties and the underlying microscopic energy transfer processes, and suggest new routes to control the carrier cooling process in metal halide perovskites to optimize optoelectronic devices.

Carbon nanotubes (CNTs) can be used in many different applications. Field emission (FE) measurements were used together with Raman spectroscopy to show a correlation between the microstructure and field emission parameters. However, field emission characterization does not suffer from fluorescence noise present in Raman spectroscopy. In this study, Raman spectroscopy is used to characterize vertically aligned CNT forest samples based on their D/G band intensity ratio (ID/IG), and FE properties such as the threshold electric field, enhancement coefficient, and anode to CNT tip separation (ATS) at the outset of emission have been obtained. A relationship between ATS at first emission and the enhancement factor, and, subsequently, a relationship between ATS and the ID/IG are shown. Based on the findings, it is shown that a higher enhancement factor (�3070) results when a lower ID/IG is present (0.45), with initial emissions at larger distances (�47 lm). For the samples studied, the morphology of the CNT tips did not play an important role; therefore, the field enhancement factor (b) could be directly related to the carbon nanotube structural properties such as breaks in the lattice or amorphous carbon content. Thus, this work presents FE as a complementary tool to evaluate the quality of CNT samples, with the advantages of alarger probe size and an averaging over the whole nanotube length. Correspondingly, one can find the best field emitter CNT according to its ID/IG.

Graphene is a highly desirable material for a variety of applications; in the case of nanocomposites, it can be functionalized and added as a nanofiller to alter the ultimate product properties, such as tensile strength. However, often the material properties of the functionalized graphene and the location of any chemical species, attached via different functionalization processes, are not known. Thus, it is not necessarily understood why improvements in product performance are achieved, which hinders the rate of product development. Here, a commercially available powder containing few-layer graphene (FLG) flakes is characterized before and after plasma or chemical functionalization with either nitrogen or oxygen species. A range of measurement techniques, including tip-enhanced Raman spectroscopy (TERS), time-of-flight secondary ion mass spectrometry (ToF-SIMS), and NanoSIMS, were used to examine the physical and chemical changes in the FLG material at both the micro- and nanoscale. This is the first reported TERS imaging of commercially available FLG flakes of submicron lateral size, revealing the location of the defects (edge versus basal plane) and variations in the level of functionalization. Graphene-polymer composites were then produced, and the dispersion of the graphitic material in the matrix was visualized using ToF-SIMS. Finally, mechanical testing of the composites demonstrated that the final product performance could be enhanced but differed depending on the properties of the original graphitic material.

Interface-mediated recombination losses between perovskite and charge transport layers are one of the main reasons that limit the device performance, in particular for the open-circuit voltage (VOC) of perovskite solar cells (PSCs). Here, functional molecular interface engineering (FMIE) is employed to retard the interfacial recombination losses. The FMIE is a facile solution-processed means that introducing functional molecules, the fluorene-based conjugated polyelectrolyte (CPE) and organic halide salt (OHS) on both contacts of the perovskite absorber layer. Through the FMIE, the champion PSCs with an inverted planar heterojunction structure show a remarkable high VOC of 1.18 V whilst maintaining a fill factor (FF) of 0.83, both of which result in improved power conversion efficiencies (PCEs) of 21.33% (with stabilized PCEs of 21.01%). In addition to achieving one of the highest PCEs in the inverted PSCs, the results also highlight the synergistic effect of these two molecules in improving device performance. Therefore, the study provides a straightforward avenue to fabricate highly efficient inverted PSCs.

Polymer solar cells (PSCs) suffer energy loss due to a number of reasons including high thermalisation, large exciton binding energy and electron-hole recombination within the active layer of the device. Although much effort has gone into addressing the above, interface recombination between a FTO cathode and ZnO electron transport layer (ETL) has remained relatively unnoticed. In this paper, an efficient inverted PSC is demonstrated by introducing a solution-processed SnO2 film between the ZnO ETL and FTO cathode. The use of the SnO2 layer, improves significantly all the device performance parameters of PSCs based on P3HT:PC61BM and PCDTBT:PC71BM system, achieving higher power conversion efficiency (PCE) up to 4.25% and 7.16%, compared to that without the SnO2 film (PCE 3.10% and 5.52%). The improved performance is attributed to the enhanced optical transmission, the reduced energy barrier and suppression of carrier recombination at the interface between the ZnO layer and cathode. Furthermore, the SnO2 film is shown to facilitate electron injection as well as effective hole blocking from the active layer. This study provides an efficient approach to optimize the device performance of PSCs by interfacial modification at bottom conductive electrode.

Large-scale incorporation of nanomaterials into manufactured materials can only take place if they are suitably dispersed and mobile within the constituent components, typically within a solution/ink formulation so that the additive process can commence. Natural hydrophobicity of many nanomaterials must be overcome for their successful incorporation into any solution-based manufacturing process. To date, this has been typically achieved using polymers or surfactants, rather than chemical functionalization, to preserve the remarkable properties of the nanomaterials. Quantifying surfactant or dispersion technique efficacy has been challenging. Here we introduce a new methodology to quantify dispersions applicable to high-weight fraction suspensions of most nanomaterials. It’s based on centrifuging and weighing residue of undispersed material. This enables the determination of the efficacy of surfactants to disperse nanomaterials (e.g. ultrasonication power and duration) and leads to increased nanomaterial solution loading. To demonstrate this technique, we assessed carbon nanotube dispersions using popular surfactants: Benzalkonium chloride (ADBAC), Brij®52, Brij®58, Pluronic®F127, sodium dodecyl sulfate (SDS), sodium dodecylbenzenesulfonate (SDBS), Triton™ X-100, Triton™X-405 and Tween®80, evaluating the dispersion outcome when varying sonicator power and horn depth, as well as imaging sono-intensity within the solution with luminol. The methodology is shown to be applicable for high-weight fraction nanomaterial suspensions, enabling greater deployment.

An efficient inverted polymer solar cell (PSC)-based on bulk heterojunction composites of poly(3-hexylthiophene) (P3HT) and phenyl C61-butryricacid methyl ester (PCBM) has been demonstrated by incorporating facile low-temperature solution-processed Mg-doped SnO2 (Mg:SnO2) nanoparticles as the cathode interfacial layer. Compared to the pure SnO2, the PSCs based on Mg:SnO2 interfacial layer exhibits excellent properties with a power conversion efficiency (PCE) of up to 4.08%, increased from 2.77%, corresponding to a significant 47.29% PCE enhancement. The improved photovoltaic performance is ascribed to the increased electron mobility, elevated electrical conductivity and optimized surface morphology, which makes it an excellent growth platform for a flat and high quality photoactive layer. Furthermore, we show the Mg:SnO2 interfacial layers to dramatically improve the electron extraction and effectively suppress the photogenerated carrier recombination. The low-temperature solution-processed SnO2 with Mg d...

Boronic acid functionalized multiwalled carbon nanotubes (bf-MWCNTs) were synthesized via a facile low temperature process and introduced in PEDOT:PSS as the composite hole transport layer (HTL), which improved the power conversion efficiency (PCE) of polymer solar cells (PSCs). The devices utilized PCDTBT:PC71BM active layers had achieved an optimal PCE of 6.953%, leading to 28% enhancement comparing to the device based on pristine PEDOT:PSS HTL. The PEDOT:PSS:bf-MWCNTs composite HTLs exhibited remarkable enhancement on hole mobility and electrical conductivity, which were beneficial to the hole extraction and transport on interface. Meanwhile, the work function (WF) of HTLs had an increase after bf-MWCNTs doping, which was matched with the highest occupied molecular orbital (HOMO) of the donor material, further improving the hole transport. Therefore, the incorporation of bf-MWCNTs efficiently improved the hole extraction and transport from active layer to the electrode.

Incorporating plasmonic nanoparticles in organic photovoltaic (OPV) devices can increase the optical thickness of the organic absorber layer while keeping its physical thickness small. However, trade-offs between various structure parameters have caused contradictions regarding the effectiveness of plasmonics in the literature, that have somewhat stunted the progressing of a unified theoretical understanding for practical applications. We examine the optical enhancement mechanisms of practical PCDTBT:PC70BM OPV cells incorporating metal nanoparticles. The plasmonic near- and far-field contributions are differentiated, with spectrum- and space-wide current enhancements found in the plasmon scattering regime and spectrum- and space-specific current enhancements in the near-field regime. A remarkable system complexity is revealed, where the plasmonic enhancement trends change and even reverse by simple changes in the device geometry. This accounts for many of the contradictory results published in the literature on plasmonic effects in OPVs. By exploring the full structural parameter phase-space we are able to now propose a unified representation that intuitively explains literature findings and trends. Our results show that an already optimized PCDTBT:PC70BM cell can be further optically enhanced by plasmonic effects by at least 20% with the incorporation of Ag nanoparticles.

Graphene is a desirable material for next generation technology. However, producing high yields of single-layer flakes with industrially applicable methods is currently limited. We introduce a combined process for the reduction of graphene oxide (GO) via vitamin C (ascorbic acid) and thermal annealing at temperatures of

Nanocomposites of carbon and molybdenum disulfide have attracted much attention due to their significant potential in energy conversion and storage applications. However, the preparation of these 0-D MoS2/carbon composites with controllable structures and desirable properties remains a major manufacturing challenge, particularly at low cost suitable for scaling-up. Here, we report a facile solution-based method to prepare porous hierarchical 0-D MoS2/carbon nanocomposites with vertical MoS2 growth on a hollow carbon support, suitable for the electrochemical storage of lithium and sodium ions. The vertically aligned MoS2/hollow carbon material shows excellent performance in the storage of a series of alkali-metal ions (e.g. Li+, Na+, and K+) with high capacity, excellent rate capacity, and stable cyclability. When used for the storage of Li+ ions, it possesses a high capacity of over 800 mA h g−1 at a rate of 100 mA g−1, with a negligibly small capacity decay as low as 0.019% per cycle. At a substantially higher rate of 5 A g−1, this MoS2/carbon nanocomposite still delivers a capacity of over 540 mA h g−1, showing its excellent performance at high rates. Remarkably, this material uniquely delivers high capacities of over 450 mA h g−1 and 300 mA h g−1 for Na+ and K+ ion storage, respectively, which are among the highest values reported to date in the literature. These excellent characteristics confirm the hollow MoS2/carbon nanocomposites to be a primary contender for next generation secondary batteries.

Metal–organic frameworks (MOFs) have emerged as an exciting class of porous materials that can be structurally designed by choosing particular components according to desired applications. Despite the wide interest in and many potential applications of MOFs, such as in gas storage, catalysis, sensing and drug delivery, electrical semiconductivity and its control is still rare. The use and fabrication of electronic devices with MOF-based components has not been widely explored, despite significant progress of these components made in recent years. Here we report the synthesis and properties of a new highly crystalline, electrochemically active, cobalt and naphthalene diimide-based MOF that is an efficient electrical semiconductor and has a broad absorption spectrum, from 300 to 2500 nm. Its semiconductivity was determined by direct voltage bias using a four-point device, and it features a wavelength dependant photoconductive–photoresistive dual behaviour, with a very high responsivity of 2.5 × 105 A W−1., Photoactive and semiconducting metal-organic frameworks are desirable for electrical and photoelectrical devices, but remain rare. Here Demets and co-workers design a naphthalene diimide and cobalt based MOF with anisotropic electrical semiconductivity and a high responsivity of 2.5 × 105 A W−1.

Carbon nanofiber (CNF) papers have been widely used in many renewable energy systems, and the development of its catalytic function is of great significance and a major challenge. In this work, we pioneer a time- and cost-efficient strategy for the preparation of large-area flexible CNF films with uniformly distributed diatomic FeN3-CoN3 sites (Fe1Co1-CNF). Due to the excellent compatibility and similar functionality of the pre-designed ZnFeCo-NC precursors (ZnFeCo-pre) with the electrospun polymer polyacrylonitrile (PAN), the mixture of ZnFeCo-pre and PAN can be co-electrospun and subject to a standard CNF fabrication process. The resulting Fe1Co1-CNF exhibits excellent bifunctional catalytic performance for both oxygen reduction reaction (ORR) and oxygen evolution reaction (OER), attributing to the abundant dual catalytic FeN3-CoN3 sites which are mutually beneficial for attaining optimal electronic properties for the adsorption/desorption of reaction intermediates. The assembled liquid-electrolyte ZAB provides a high specific power of 201.7 mW cm−2 and excellent cycling stability. More importantly, due to the good mechanical strength and flexibility of Fe1Co1-CNF, portable ZAB with exceptional shape deformability and stability can be demonstrated, in which Fe1Co1-CNF utility as an integrated free-standing membrane electrode. These findings provide a facile strategy for manufacturing flexible multi-functional catalytic electrodes with high production.

Summary The endeavors to develop manufacturing methods that can enhance polymer and composite structures in spacecraft have led to much research and innovation over many decades. However, the thermal stability, intrinsic material stress, and anisotropic substrate properties pose significant challenges and inhibit the use of previously proposed solutions under extreme space environment. Here, we overcome these issues by developing a custom-designed, plasma-enhanced cross-linked poly(p-xylylene):diamond-like carbon superlattice material that enables enhanced mechanical coupling with the soft polymeric and composite materials, which in turn can be applied to large 3D engineering structures. The superlattice structure developed forms an integral part with the substrate and results in a space qualifiable carbon-fiber-reinforced polymer featuring 10–20 times greater resistance to cracking without affecting the stiffness of dimensionally stable structures. This innovation paves the way for the next generation of advanced ultra-stable composites for upcoming optical and radar instrument space programs and advanced engineering applications., Graphical abstract, Highlights • Plasma-enhanced cross-linked poly(p-xylylene) (PECLP):DLC superlattice is deposited • PECLP exhibits ∼10 times higher elastic modulus compared to classic poly(p-xylylene) • PECLP:DLC barrier provides near-zero stress conditions for use on composites • Enhanced composites exhibit mechanical integrity and improved crack resistivity, Aerospace Engineering; Engineering materials; Materials physics

Understanding how the brain works requires developing advanced tools that allow measurement of bioelectrical and biochemical signals, including how they propagate between neurons. The introduction of nanomaterials as electrode materials has improved the impedance and sensitivity of microelectrode arrays (MEAs), allowing high quality recordings of single cells in situ using electrode diameters of ≤20 μm. MEAs also have the potential to measure electroactive biological molecules in situ, such as dopamine, a neurotransmitter in the nervous system. Thus, this work focused on fabricating a functionalised carbon nanotube (CNT)-based MEA to demonstrate its potential for future measurement of small signals generated from excitable cells. To this end, the functionalised CNT MEA has recorded one of the lowest electrochemical interfacial impedances available in the literature, 2.8±0.2 kΩ, for an electrode of its geometric surface area. Electrochemical detection of dopamine revealed again one of the best sensitivity values per area available in the literature, 9.48 μA μM−1 mm−2. Additionally, a limit of detection of 7 nM was recorded for dopamine using the functionalised CNT MEA, with selectivity against common electrochemical interferents such as ascorbic acid. These results indicate improvement beyond currently available MEAs, along with the feasibility of using these devices for multi-site detection of physiologically relevant electroactive biomolecules.

Graphene poly-acrylic and PEDOT:PSS nanocomposite films were produced using two alternative commercial graphene powders to explore how the graphene flake dimensions and chemical composition affected the electrical performance of the film. A range of analytical techniques, including scanning electron microscopy (SEM), atomic force microscopy (AFM), Raman spectroscopy, X-ray photoelectron spectroscopy (XPS) and time-of-flight secondary ion mass spectrometry (ToF-SIMS), were employed to systematically analyse the initial graphene materials as well as the nanocomposite films. Electrical measurements indicated that the sheet resistance of the films was affected by the properties of the graphene flakes used. To further explore the composition of the films, ToF-SIMS mapping was employed and provided a direct means to elucidate the nature of the graphene dispersion in the films and to correlate this with the electrical analysis. These results reveal important implications for how the dispersion of the graphene material in films produced from printable inks can be affected by the type of graphene powder used and the corresponding effect on electrical performance of the nanocomposites. This work provides direct evidence for how accurate and comparable characterisation of the graphene material is required for real-world graphene materials to develop graphene enabled films and proposes a measurement protocol for comparing graphene materials that can be used for international standardisation.

Polymer solar cell (PSC) manufacturing is strongly influenced by the thin film deposition method with the morphology of the bulk heterojunction (BHJ) coupled intimately to the efficiency of the device. Although ideally scalable deposition methods suitable for sheet-to-sheet (S2S) or roll-to-roll (R2R) production should be used in the investigation of PSCs, research still predominately relies on spin-coating due to ease of use and lower associated costs. Here we present the development and characterization of a lab-scale slot-die coater and demonstrate its use to fabricate air-stable, large-area, solar cell modules. We adapt an entry level paint applicator into a fully-functional S2S slot-die coater and provide its open source documentation to support the research community in availing itself of scalable photovoltaic technologies for device fabrication. The optimization of the process parameters results in homogeneous layers that have been extensively characterized by light beam induced current (LBIC), micro photoluminescence (PL), and micro Raman mapping of whole modules. We report the successful demonstration of the fabrication of PSC modules with an active area above 35 cm 2 and a power conversion efficiency exceeding 3%. We also investigate the behavior of the module characteristics at different annealing temperatures and its stability during operation under ambient conditions. This work will facilitate research on scaling up of laboratory organic electronic devices and allow more efficient transition from Lab-to-Fab.

The concept of magnetic induction of hyperthermia was first proposed by Gilchrist et al. in 1957. The physics is based on the simple principle that when exposed to an alternating magnetic field, the magnetic media can transform the electromagnetic energy to thermal energy, causing the temperature increase of any surrounding media or tissue. In biological tissue, normal cells usually possess higher heat resistance and resilience to temperature than tumor cells. As such, cancerous cells can be selectively destroyed by increasing the local temperature of the tissue to a desired temperature range (42–46°C), while ensuring healthy cells are unharmed.

Some of the key challenges in the applications of graphene and carbon nanotubes are associated with their poor attachment to the substrate and poisoning of the catalyst by environmental contamination prior to the growth phase. Here we report a ‘protected catalyst’ technique which not only overcomes these challenges but also provides a new material production route compatible with many applications of carbon nanomaterials. The breakthrough technique involves capping the catalyst with a protective layer of a suitable material (examples include TiN, Cr, Ta) which protects the catalyst from environmental contaminants such as oxidation, etchant attack, etc., whilst maintaining carbon supply to the catalyst for the CVD growth of desired nanomaterial. A thin Fe catalyst layer remained protected due to the capping layer in the CF4 based reactive-ion-etching of SiO2. We show that the carbon nanostructures grown using this technique exhibit significantly improved adhesion to the substrate in sonication bath tests. We demonstrate the fabrication of 3D structures and CNT based vias in a buried catalyst arrangement using the protected catalyst technique. The technique also allows better control over various growth parameters such as number of graphene layers, growth rate, morphology, and structural quality.

Graphene-based carbon sponges can be used in different applications in a large number of fields including microelectronics, energy harvesting and storage, antimicrobial activity and environmental remediation. The functionality and scope of their applications can be broadened considerably by the introduction of metallic nanoparticles into the carbon matrix during preparation or post-synthesis. Here, we report on the use of X-ray micro-computed tomography (CT) as a method of imaging graphene sponges after the uptake of metal (silver and iron) nanoparticles. The technique can be used to visualize the inner structure of the graphene sponge in 3D in a non-destructive fashion by providing information on the nanoparticles deposited on the sponge surfaces, both internal and external. Other deposited materials can be imaged in a similar manner providing they return a high enough contrast to the carbon microstructure, which is facilitated by the low atomic mass of carbon.

This paper presents the extraction of the complex propagation constant from carbon fiber reinforced plastic (CFRP) transmission lines up to 5 GHz. A test-fixture is designed and fabricated to obtain the propagation constant using a line-line extraction method. Use of this method reduces the required number of fabricated transmission lines compared to calibration algorithms such as TRL. Comparison of the extracted propagation constant with simulation data indicates CFRP conductivity of 1.0 –1.5x104 S/m.

Metal halide perovskite solar cells are emerging candidates for next‐generation thin‐film photovoltaic devices with the potential for extremely low fabrication cost and high power conversion efficiency. Perovskite solar cells have demonstrated a rapid development in device performance over the last decade, from an initial 3.81% to a most recently certified 24.2%, though the challenges of long‐term stability and lead toxicity still remain. Carbon materials, ranging from zero‐dimensional carbon quantum dots to three‐dimensional carbon black materials, are promising candidates for the enhancement of both efficiency and stability of perovskite solar cells, offering unique advantages for incorporation into various device architectures. In this review article, we present a concise overview of important and exciting advancements of perovskite solar cells that incorporate different dimensions of carbon material in their device architectures in an effort to simultaneously improve device performance and long‐term stability. We also discuss the major advantages and potential challenges of each technique that has been developed in the most recent work. Finally, we outline the future opportunities toward more efficient and stable perovskite solar cells utilizing carbon materials.

To enhance the performance of inverted structure polymer solar cells (PSCs), interfacial engineering considered as an effective and straightforward method was employed. In this study, to overcome the surface traps and energy level mismatches of the electron transport layer, a means of interface passivation by evaporating an ultrathin CaF2 layer above ZnO thin film as the electron transport layer was successfully adopted. We display that CaF2 layer could passivate the surface traps of ZnO thin film and decrease the interfacial barrier between PC61BM and ZnO, so that electron transfer efficiency is facilitated, the recombination of electrons and holes is inhibited at the contact interface, and the series resistance is reduced. After the introduction of the CaF2 layer, the short-circuit current and the fill factor was greatly improved, also the power conversion efficiency (PCE) was increased from 3.21% of the reference device without the CaF2 layer to 4.22% in the inverted PSCs based on P3HT:PC61BM bulk heterojunction photoactive layer. These results could have special guiding significance for high-efficiency PSCs and also great potential for applications of photovoltaic devices in the future.

For the first time, thin insulating layers are used to modulate a depletion region at the source of a thin-film transistor. Bottom contact, staggered electrode transistors fabricated using RFsputtered IGZO as the channel layer, with a 3 nm ALD Al2O3 layer between the semiconductor and Ni source-drain contacts show behaviours typical of source-gated transistors (SGTs): low saturation voltage (VD_SAT ~ 3V), change in VD_SAT with gate voltage of only 0.12 V/V and flat saturated output characteristics (small dependence of drain current on drain voltage). The transistors show high tolerance to geometry variations: saturated current changes only 0.15x for channel lengths between 2 - 50 μm, and only 2x for sourcegate overlaps between 9 - 45 μm. A higher than expected (5x) increase in drain current for a 30K change in temperature, similar to Schottky-contact SGTs, underlines a more complex device operation than previously theorised. Optimizations for increasing intrinsic gain and reducing temperature effects are discussed. These devices complete the portfolio of contactcontrolled transistors, comprising devices with: Schottky contacts, bulk barrier or heterojunctions, and now, tunnelling insulating layers. The findings should also apply to nanowire transistors, leading to new low-power, robust design approaches as large-scale fabrication techniques with sub-nanometre control mature.

Enhanced power conversion efficiency is reported in inverted polymer solar cells when an ultrathin layer of strontium fluoride (SrF2) is evaporated on the surface of the solution-processed zinc oxide (ZnO) electron transport layer. The photoactive layer is made up of bulk heterojunction composites of poly[4,8-bis(5(2-ethylhexyl)thiophen-2-yl)benzo[1,2-b:4,5-b′]dithiopheneco-3-fluorothieno[3,4-b]-thiophene-2-carboxylate] and [6,6]-phenyl-C71-butyric acid methyl ester. The ZnO film acts as an effective electron transport layer, whereas the ultrathin SrF2 layer improves the energy level alignment and enhances the built-in potential via the formation of an interfacial dipole layer at the interfaces between the ZnO film and the photoactive layer, resulting in an enhanced electron extraction efficiency and a decreased carrier recombination loss. Furthermore, the SrF2 layer reduces the inherent incompatibility between the hydrophilic ZnO film and the hydrophobic photoactive layer. As a result, all the photovolta...

The predicted 50 billion devices connected to the Internet of Things by 2020 has renewed interest in polysilicon technology for high performance new sensing and control circuits, in addition to traditional display usage. Yet, the polycrystalline nature of the material presents significant challenges when used in transistors with strongly scaled channel lengths due to non-uniformity in device performance. For these new applications to materialize as viable products, uniform electrical characteristics on large areas will be essential. Here, we report on the effect of deliberately engineered potential barrier at the source of polysilicon thin-film transistors, yielding highly-uniform on-current (

Strategies to maximize the surface charge density across triboelectric layers while protecting it from humidity are crucial in employing triboelectric nanogenerators (TENGs) for commercial/real-time applications. Herein, for the first time, we propose the utility of crystalline silk microparticles (SMPs) to improve the surface charge density in materials like polyvinyl alcohol to realise its applicability for TENG devices. Moreover, these SMPs are extracted from discarded Bombyx mori silkworm cocoons by facile, inexpensive, and single-step alkaline-hydrolysis treatment. We examine the performance of these composites with counter-materials composed of waste PTFE plastic cups to show reuse in recycled products. The processing cost of TENG developed from recycled materials is not only low but eco-friendly. The TENG performance as a function of the concentration of SMPs is investigated and compared with the composite's work-function and surface-potentials, with the distance-dependent electric field theoretical model employed to optimize the performance. Consequently, the optimized TENG exhibits maximum output voltage, current, charge, and power density of ∼280 V, 17.3 μA, 32.5 nC, and 14.4 W·m−2, respectively, creating a highly competitive energy harvester that can conform to the rigorous needs of wearables and mobile applications. Furthermore, the fully packaged silicone rubber device protects it from humidity and enables the device utility for practical applications with a soft, comfortable, and skin-friendly interface.

The allure of all-carbon electronics stems from the spread of its physical properties across all its allotropes. The scheme also harbours unique challenges, such as tunability of band gap, variability of doping and defect control. Here, we explore the technique of scanning probe tip-induced nanoscale reduction of graphene oxide (GO), which nucleates conducting, sp 2 rich graphitic regions on the insulating GO background. The flexibility of direct writing is supplemented with control over the degree of reduction and tunability of band gap through macroscopic control parameters. The fabricated reduced GO channels and ensuing devices are investigated via spectroscopy and temperature and bias-dependent electrical transport and correlated with spatially resolved electronic properties, using surface potentiometry. The presence of carrier localization effects, induced by the phase-separated sp 2 / sp 3 domains, and large local electric field fluctuations are reflected in the non-linear transport across the channels. Together, the results indicate a complex transport phenomenon, which may be variously dominated by tunnelling or variable range hopping or activated depending on the electronic state of the material.

The effect of incorporating graphene quantum dots (GQDs) synthesized by a hydrothermal method in the active layer of organic solar cells was investigated. The doping of GQDs into poly[N-9′′-hepta-decanyl-2,7-carbazole-alt-5,5-(4′,7-di-2-thienyl-2′,1′,3′-benzothiadiazole)]:C71-butyric acid methyl ester (PCDTBT:PC71BM) active layer resulted in 21% enhancement in power conversion efficiency. The doped GQDs act as exciton dissociation centres in the PCDTBT:PC71BM system. The improvement can be mainly attributed to the fact that the GQDs provide plenty of exciton dissociation interfaces and improve the charge transport pathway. Moreover, the doping of GQDs also offered a general route to optimize the light absorption of organic photovoltaic devices. Our results indicate that doping of hydrothermally synthesized GQDs offers a facile approach to improve the performance of the polymer solar cells.

International audience; New materials and optimized fabrication techniques have led to steady evolution in large area electronics, yet significant advances come only with new approaches to fundamental device design. The multimodal thin-film transistor introduced here offers broad functionality resulting from separate control of charge injection and transport, essentially using distinct regions of the active material layer for two complementary device functions, and is material agnostic. The initial implementation uses mature processes to focus on the device's fundamental benefits. A tenfold increase in switching speed, linear input-output dependence, and tolerance to process variations enable low-distortion amplifiers and signal converters with reduced complexity. Floating gate designs eliminate deleterious drain voltage coupling for superior analog memory or computing. This versatile device introduces major new opportunities for thin-film technologies, including compact circuits for integrated processing at the edge and energy-efficient analog computation.