Search

This study evaluates the use of fermentation to increase nutrient availability in pulp and paper bio-sludge (PPBS) as feed for black soldier fly larvae (BSFL). Rearing of BSFL on fermented PPBS was carried out in a climate chamber in order to assess nutrient availability and larvae survival and growth. The PPBS used came from a chemo-thermomechanical pulp/groundwood pulp mill. The PPBS was fermented at 35 °C and 55 °C, respectively, at initial pH of 10. The effects of sediment and liquid from fermented PPBS on larvae dry weight, survival rate until the prepupae stage, bioconversion, and reduction rate of PPBS were measured. The bioconversion of the liquids (4.1–6.6%) was substantially higher than for both the sediments and untreated PPBS (≤ 0.4%). The survival rate, on the other hand, was substantially lower (26.3–30.9 %) than for the sediments and untreated PPBS (49.5–52.6%). Neither the sediments nor the liquids had significant effects on the larvae weight or on the PPBS reduction rate. The sediments had no significant effect on the survival rate or the bioconversion. This study demonstrates that fermentation dissolves a part of the PPBS and that dissolved substances in the fermentation liquid readily convert to larvae biomass. However, the bulk of the lignocellulose is not dissolved, and most of PPBS nutrients remain unavailable for growth of the larvae. Further research should focus on improved pretreatment of PPBS to increase availability of nutrients and thereby improve the feasibility of BSFL as a recycling method for PPBS.

We report a paper-based photodetector made from mixed cation organic perovskite halide MA1–xFAxPbI3 (MA = methylammonium (CH3NH3); FA = formamidium CH(NH2)2). The detector shows a substantial photo...

Biodiesel, as a green fuel, acts as a potential candidate to supplement conventional fossil fuels. This research study targets green environment (using biodiesel) and clean environment (reduce wastewater) by producing biodiesel through oleaginous biomasses (Yarrowia lipolytica, Metschnikowia pulcherrima and Lipomyces starkeyi) grown on pulp and paper industrial wastewater. Batch culture studies were explored for the potential feedstock of the oleaginous organism by the synthesis of single cell oil and fatty acid methyl ester (FAME) yield. Response surface methodology (RSM) was used to design the optimal experimental matrix and identify the optimal process conditions that enhance the FAME yield. To determine the inherent characteristics of the growth of oleaginous biomasses on the industrial wastewater, a data-driven adaptive neuro-fuzzy inference system (ANFIS) is implemented. Y. lipolytica strain cultured shown high biomass concentration of 32.36 g/l with biomass productivity of 5.39 g/l/d was considered for further scale-up for the transesterification process. Results indicated that the maximum yield of 0.48 (g-biodiesel/g-lipid) was obtained under the 2.5 g of lipid dosage with 0.02 g/ml of catalyst concentration by constant stirring at 70 °C. The optimum conditions to achieve maximum FAME yield of 1.154 g/g was obtained at 2.485 g, 70.87 °C and 0.021 g/ml for lipid dosage, temperature and catalyst concentrations, respectively.

Achieving an efficient catalyst in the ATRP system with a simple design, preparation from available materials, and high recyclability is a significant challenging issue. To attain the goal, herein, we used chitosan (CS)-modified cellulose filter paper (FP) as a green support for the synthesis of dip catalyst. The preparation of this catalyst involved surface treatment of the FP strips by CS coating through a dipping method, which increased the affinity of the substrate for adsorbing copper ions in the next step. The Cu@CS-FP catalyst was prepared without the requirement of any ligands. The synthesized dip-catalyst, in the form of the strips, was employed for the first time in the ATRP reaction of methyl methacrylate to assay catalytic activity. Catalytic insertion/ removal (ON/OFF) experiments were carried out during the polymerization. A reasonable control over the molecular weight with high conversion (68%) and polydispersity index of 1.32 under mild reaction conditions were obtained. Significantly, because of the facile separation of the catalyst, the amount of copper that remained in the polymer was very low (2.7 ppm). Also, the recyclability of the catalyst was investigated for five runs. The conversion in the final run was 64% without a loss of catalyst efficiency.

Industrial effluent Management is one of the major environmental concerns, especially in developing countries under rapid industrialization. The grossly polluting industries recognized by Central Pollution Control Board (CPCB), such as Pulp and Paper Industries, poses even bigger environmental threats, owing to quantity and quality of effluent generated. This paper aimed at analyzing effluent management practices in pulp and paper industries in India, and asses the performance variability of a paper mill effluent treatment plant (ETP), as a Case Study. Majority of pulp and paper industries found to still employ conventional methods of effluent treatment. Although, most of the parameters of treated effluent are commonly reported within CPCB’s permissible discharge limits, the treatment is usually cost and energy intensive, and produce high amount of solid residuals as sludge. For the case study paper mill ETP, the treatment efficiencies of the ETP units were analyzed under variable inlet pH, TSS, TDS, BOD and COD loads. The pH variations in the range of 6.5 to 9 had little effect of COD or TSS removal, however removal efficiencies were higher for larger inlet COD or TSS loads. The results of the study could be helpful in optimizing operation of the existing ETPs, as well as, guiding on upgrading ETPs with more cost-effective and efficient units.

Microfluidic paper-based analytical devices (μPADs) have developed rapidly in recent years, because of their advantages, such as small sample volume, rapid detection rates, low cost, and portability. Due to these characteristics, they can be used for in vitro diagnostics in the laboratory, or in the field, for a variety of applications, including food evaluation, disease screening, environmental monitoring, and drug testing. This review will present various detection methods employed by μPADs and their respective applications for the detection of target analytes. These include colorimetry, electrochemistry, chemiluminescence (CL), electrochemiluminescence (ECL), and fluorescence-based methodologies. At the same time, the choice of labeling material and the design of microfluidic channels are also important for detection results. The construction of novel nanocomponents and different smart structures of paper-based devices have improved the performance of μPADs and we will also highlight some of these in this manuscript. Additionally, some key challenges and future prospects for the use of μPADs are briefly discussed.

Plant fiber classified as environmentally friendly material is a promising renewable engineering material rich in lignocellulose that can be employed in the pulp and paper industry as a substitutio...

Thermochemical parameters of A4-sized printing paper (AP), filter paper (FP), newspaper (NP), writing paper (WP), and reed pith (RP) samples were estimated using standard protocol to identify its fuel characteristics, and thermal degradation of the same was studied using thermogravimetric analysis (TGA) and differential thermogravimetric (DTG) techniques in the temperature range of 30–800 °C at the heating rates of 10, 15, and 20 °C/min under nitrogen atmosphere. The curves of TGA and DTG exhibited four significant stages. Maximum weight loss was found to be in the second stage. Kinetic analysis was carried out in the conversion range of 0.1 to 0.7 using iso-conversational models of Flynn-Wall-Ozawa (FWO), Kissinger-Akahira-Sunose (KAS), Vyazovkin, and Vyazovkin AIC (V.AIC). The average activation energies were found to be 139.90, 115.93, 212.52, 257.41, and 241.63 kJ/mol using FWO; 129.73, 103.06, 202.46, 248.38, and 231.55 kJ/mol using KAS; 145.57, 134.00, 195.29, 256, and 241.63 kJ/mol using Vyazovkin; and 140.71, 133.86, 193.14, 247.57, and 190.14 kJ/mol using Vyazovkin AIC model. Thermodynamic parameters (enthalpy change (ΔH), Gibbs free energy change (ΔG), and entropy change (ΔS)) using these models have been evaluated.

All-cellulose paper-based composites with underwater superoleophobicity and high-wet-strength were developed by casting a barrier layer of bacterial cellulose (BC) on a filter paper substrate. To optimize the pore structure of barrier layer, slow gel process of BC dispersion was conducted via acidification and solvent exchange. 1,2,3,4-butanetetracarboxylic acid was used to improve the wet strength and surface hydrophilicity through the crosslinking reaction between fibers. The underwater oil contact angles are higher than 150° in neutral environment, and slightly decrease under acid and alkali conditions. Combined with the micron-sized pore structure of BC barrier layer, the composite papers show good separation performance of oil-in-water emulsion. A denser BC layer can significantly improve the separation efficiency, but also lead to the reduction of flux. During the gelation of BC barrier layer, the increase in the ethanol/water ratio of the dispersion medium is able to increase the flux without obvious negative impact on the separation efficiency. When the ethanol/water ratio is 80%, the separation efficiency and water flux reach 99.2% and 1320 L m−2 h−1·bar−1 for the emulsified soybean oil with the average size of 13 μm, respectively. This type of all-cellulose composite papers provides a new idea for the fabrication of membrane materials for oil–water separation.

In this paper, we present a system for automatic evaluation of the quality of a question paper. Question paper plays a major role in educational assessment. The quality of a question paper is crucial to fulfilling the purpose of the assessment. In many education sectors, question papers are prepared manually. A prior analysis of a question paper might help in finding the errors in the question paper, and better achieving the goals of the assessment. In this experiment, we focus on higher education in the technical domain. First, we conducted a student survey to identify the key factors that affect the quality of a question paper. The top factors we identified are question relevance, question difficulty, and time requirement. We explored the strategies to handle these factors and implemented them. We employ various concepts and techniques for the implementation. The system finally assigns a numerical quality score against these factors. The system is evaluated using a set of question papers collected from various sources. The experimental results show that the proposed system is quite promising.

This paper aimed to modify the ignitability of the bagasse paper by using talc powder, 1,3-di-aniline-2,2,2,4,4,4-hexachlorocyclodiphosph(V)azane, and nanocellulose crystal. The formation of cellulose nanocrystals (CNCs) was detected using transmission electron microscopy (TEM), X-ray diffraction (XRD). Thermal analysis as thermal gravimetric analysis (TGA) of the specimens recorded the improvement of the highest % of ash residue at 750 °C compared to the untreated one. The shape of the flame spread was studied. The ignition properties were studied for the untreated and treated specimens by limiting oxygen index (LOI) and flame chamber (UL/94), which recorded enhancing compared to the untreated specimen. This improvement was recorded either by measuring the mechanical properties (tensile strength, burst strength, elongation, and elasticity) of the specimens. The current article showed that the treated specimen was recorded the highest values compared to the untreated one in all physical, mechanical, and ignition properties, so these treatment paper sheets may be used as fire-retardant packaging materials.

A paper-based membrane coated by graphitic carbon nitride (g-C3N4) is prepared via a dip-coating method and used as a separator for sodium metal batteries with merits of low cost and environment-friendliness. Introduction of g-C3N4 effectively improves the ionic conductivity and the structural stability of the separator. Compared with traditional polyethylene separators and Al2O3-coated separators, the g-C3N4-coated separators show better electrolyte wettability, thermal stability, and electrochemical stability. Therefore, Na||Na3V2(PO4)3 battery using the g-C3N4-coated separator exhibits better cycling stability and higher rate capability. These results prove that the g-C3N4-coated paper-based separator is expected to become the next generation of low-cost and high-safety separator in sodium metal batteries.

The present study illustrates the electrocoagulation remediation of paper mill wastewater for multiple response optimization. Multiple response optimization can be combined into one desirability function. All variables and responses varied for a unique global solution. The effect of basic electrocoagulation process variables pH (3–10), conductivity (3.15–10 mS/cm), electrode distance (1–2.5 cm) and current density (5–20 mA/cm2) on four response parameters such as chemical oxygen demand, color, total dissolved solids and total organic carbon has been analyzed experimentally and statistically. The global solution for these variables and responses obtained by software over a hundred design points. For unit desirability function variables conditions were pH 7.49, Conductivity 8.34 mS/cm, electrode distance 2.06 cm and current density 9.32 mA/cm2. In these global variable conditions, responses were observed to be COD 70.19%, Color 75.03%, TDS 70.69% and TOC 71.93%, respectively.

This study investigated the feasibility of utilizing paper sludge (PS) as feedstock in the production of composite boards that are lightweight, durable and environmentally friendly. PS samples were collected from recycled newsprint (RN), corrugated recycled (CR) and virgin pulp (VP) pulping mills in South Africa. The PS was dried and mixed with magnesium phosphate cement to produce boards in a central composite design. Three different fillers including fly ash, calcium carbonate and silica fume were also added to the mix as binder replacement. The PS was characterized before use, and the produced composite board was evaluated for mechanical and physical properties. The boards produced had medium to high density (0.52—1.12 g/cm3) that could be used for non-structural interior applications. The results showed that boards containing RN had the highest mean value for modulus of elasticity (MOE) of 769 MPa. The mean MOE for boards containing CR- and VP-PS was 357 and 411 MPa, respectively. Calcium carbonate had the best effect on the board properties. Techno-economic analysis was simulated for four different types of feedstock scenarios at different locations including a combined scenario. Sensitivity analysis revealed that decreased feedstock cost resulted in decreased minimum required selling price. The analysis also revealed that the combined scenario proved to be the most cost-effective and profitable option for the future.

PurposeThis study develops an integrated zero waste discharge planning approach for improving resource efficiency in a pulp-and-paper manufacturing firm.Design/methodology/approachThe objectives of this study are to (1) identify the environmental, technical and social metrics in resource efficiency; (2) utilize fuzzy multi-objective programming and the hybrid particle swarm optimization algorithm to solve the fuzzy problem; and (3) develop an assessment for resource efficiency improvement in an industrial case study.FindingsThe findings demonstrate the superiority of hybrid particle swarm optimization algorithm in generating optimal results for a pulp-and-paper manufacturing firm.Practical implicationsThe findings demonstrate the superiority of hybrid particle swarm optimization algorithm in generating optimal results for a pulp-and-paper manufacturing firm.Originality/valueResource efficiency is a multi-objective problem in an uncertain environment. In particular, zero waste discharge planning involves minimizing the total cost and maximizing the waste material recovery rate, wastewater reuse, and waste heat recovery.

Compared with a single chemical indicator, the use of multivariate chemical indicators in aging status assessment of transformer cellulose paper insulation can improve the reliability of the evaluation. In this study, a non-destructive method based on multivariate chemical indicators was proposed to evaluate the remaining life of cellulosic paper insulation. The selected chemical indicators closely related to the aging of the insulating paper were analyzed. Additionally, by applying the subjective and objective weighting method, the evaluation information of each indicator was fully extracted to obtain reasonable comprehensive evaluation weights. Besides, the comprehensive evaluation index of multivariate chemical indicators was obtained by using the technique for order preference by similarity to ideal solution method, which is consistent with the deterioration law of paper insulation. Then, the correlation lifespan model between the comprehensive evaluation index of multivariate chemical indicators and the degree of polymerization of insulating paper under different aging stages was established. The effectiveness of the proposed model was verified by experiments. This promising model can increase the accuracy of the condition assessment for the transformer cellulosic paper insulation.

Flexible paper-based sensors may be applied in numerous fields, but this requires addressing their limitations related to poor thermal and water resistance, which results in low service life. Herein, we report a paper-based composite sensor composed of carboxylic carbon nanotubes (CCNTs) and poly-m-phenyleneisophthalamide (PMIA), fabricated by a facile papermaking process. The CCNT/PMIA composite sensor exhibits an ability to detect pressures generated by various human movements, attributed to the sensor's conductive network and the characteristic "mud-brick" microstructure. The sensor exhibits the capability to monitor human motions, such as bending of finger joints and elbow joints, speaking, blinking, and smiling, as well as temperature variations in the range of 30-90 °C. Such a capability to sensitively detect pressure can be realized at different applied frequencies, gradient sagittas, and multiple twists with a short response time (104 ms) even after being soaked in water, acid, and alkali solutions. Moreover, the sensor demonstrates excellent mechanical properties and hence can be folded up to 6000 times without failure, can bear 5 kg of load without breaking, and can be cycled 2000 times without energy loss, providing a great possibility for a long sensing life. Additionally, the composite sensor shows exceptional Joule heating performance, which can reach 242 °C in less than 15 s even when powered by a low input voltage (25 V). From the perspective of industrialization, low-cost and large-scale roll-to-roll production of the paper-based sensor can be achieved, with a formed length of thousands of meters, showing great potential for future industrial applications as a wearable smart sensor for detecting pressure and temperature, with the capability of electric heating.

The plasmonic properties of gold nanoparticles (AuNPs) are a promising tool to develop sensing alternatives to traditional, enzyme-catalyzed reactions. The need for sensing alternatives, especially in underdeveloped areas of the world, has given rise to the application of nonenzymatic sensing approaches paired with cellulosic substrates to biochemical analysis. Herein, we present three individual, low-step, wet-chemistry, colorimetric assays for three target biomarkers, namely, glucose, uric acid, and free cholesterol, relevant in diabetes control and their translation into paper-based assays and microfluidic platforms for multiplexed analysis. For glucose determination, an in situ AuNPs synthesis approach was applied into the developed μPAD, giving semiquantitative measures in the physiologically relevant range. For uric acid and cholesterol determination, modified AuNPs were used to functionalize paper with a gold-on-paper approach with the optical properties changing based on different aggregation degrees and hydrophobic properties of particles dependent on analyte concentration. These paper-based assays show sensitivity ranges and limits of detection compatible for target analyte level determination and detection limits comparable to those of similar enzymatic, colorimetric systems, relying only on plasmonic transduction without the need for enzymatic activity or other chromogenic substrates. The resulting paper-based assays were integrated into a single 3D, multiplex paper-based device using paper microfluidics, showing the capability for performing different colorimetric assays with distinct requirements in terms of sample flow and sample uptake in test zones using a combination of both horizontal and vertical flows inside the same device. The presented device allows for multiparametric, colorimetric measures of different metabolite levels from a single complex sample matrix drop using digital color analysis, showing the potential for development of low-cost, low-complexity tools for diagnostics toward the point-of-care.

Gelatine sizing was used extensively for western papermaking before the nineteenth century and this technique is still applied nowadays for restoration purposes. Despite its wide use, the relationships between gelatine types, the strength of the size and its distribution inside the paper sheet are still unclear. Different concentrations of three gelatines of various origins and types (A/B) were used to size model papers. The gelatine uptake, the strength of the size and the presence of gelatine at the papers surface were investigated by using a water drop test method and ATR-FTIR spectroscopy. At a given concentration, similar uptakes were found for all gelatines but great variations were observed in terms of size strength and of gelatine ability to cover the surface of paper sheets. In addition, Scanning transmission X-ray microscopy was performed on paper fibres cross sections to map the distribution of the organic compounds (both cellulosic and proteinaceous) on a nanometer scale. This showed that gelatine coats but does not penetrate the fibres. It can be inferred that the different size strengths observed between the tested gelatines are mainly due to different ways of filling holes between fibres inside the paper mat, some gelatines being more prone to go inside the sheet than others which remain mostly distributed near the surface.

Loop-mediated isothermal amplification (LAMP) has been widely used to detect many infectious diseases. However, minor inconveniences during the steps of adding reaction ingredients and lack of simple color results hinder point-of-care detection. We therefore invented a fluorometric paper-based LAMP by incorporating LAMP reagents, including a biotinylated primer, onto a cellulose membrane paper, with a simple DNA fluorescent dye incubation that demonstrated rapid and accurate results parallel to quantitative polymerase chain reaction (qPCR) methods. This technology allows for instant paper strip detection of methicillin-resistant Staphylococcus aureus (MRSA) in the laboratory and clinical samples. MRSA represents a major public health problem as it can cause infections in different parts of the human body and yet is resistant to commonly used antibiotics. In this study, we optimized LAMP reaction ingredients and incubation conditions following a central composite design (CCD) that yielded the shortest reaction time with high sensitivity. These CCD components and conditions were used to construct the paper-based LAMP reaction by immobilizing the biotinylated primer and the rest of the LAMP reagents to produce the ready-to-use MRSA diagnostic device. Our paper-based LAMP device could detect as low as 10 ag (equivalent to 1 copy) of the MRSA gene mecA within 36-43 min, was evaluated using both laboratory (individual cultures of MRSA and non-MRSA bacteria) and clinical blood samples to be 100% specific and sensitive compared to qPCR results, and had 35 day stability under 25 °C storage. Furthermore, the color readout allows for quantitation of MRSA copies. Hence, this device is applicable for point-of-care MRSA detection.

Natural cellulose paper is flame retarded using ammonium polyphosphate/montmorillonite (APP/MMT) nanocompound through coating method. Their morphologies are assessed by scanning electron microscopy, chemical components by energy dispersive X-ray spectroscopy and X-ray photoelectron spectroscopy, chemical structure by Fourier transform infrared, thermal stability by thermo-gravimetric analysis and fire retardancy by 45° horizontal burning test. The results show that the thermal stability and flame retardancy of coated paper samples are enhanced obviously, and all samples are self-extinguishing during the tests due to the char formation reaction between APP/MMT and cellulose. Then the treated paper, AM-18.3, as surface flame retardant treatment for low specific surface area (SSA) polypropylene (PP) specimens (PP@AM-18.3) also is investigated using cone calorimeter. Compared with two controlled samples, PP@AM-18.3 shows significantly increased time to ignition, the lowest fire growth index and highest fire performance index. This may give a new flame retarded approach for low SSA polymer materials with little amount flame retardants.

Herein, combined with a pervasive smartphone installed with a color recognition app, dual-responsive CDs@Eu/GMP ICPs were designed as a red-to-blue paper-based colorimetric sensor for the point-of-use analysis of cerebral acetylcholinesterase (AChE) upon Cd2+ exposure. Blue-emitting CDs with multi-functional groups as guests were encapsulated into the network of Eu/GMP ICPs to obtain CDs@Eu/GMP ICPs with the sensitized red fluorescence of Eu3+. With the presence of thiocholine (TCh), derived from acetylthiocholine (ATCh) hydrolyzed by AChE, the coordination environment of the CDs@Eu/GMP ICPs was interrupted, leading to the collapse of the CDs@Eu/GMP ICP network and the corresponding release of guest CDs into the surrounding environment. Consequently, the sensitized red fluorescence of Eu3+ decreased and the blue fluorescence of the CDs increased. This obvious red-to-blue fluorescent color changes of CDs@Eu/GMP ICPs on test paper could then be integrated with the smartphone for point-of-use analysis of cerebral AChE upon Cd2+ exposure, which not only offers a new analytical platform for a better understanding of the environmental risk of Alzheimer's Dementia (AD), but also holds great potential in the early diagnosis of AD even at the asymptomatic stage with the decrease in CSF AChE as an early biomarker.

Edible oils form an integral component in the human diet as well as in the industrial preparations. Any adulteration in oil is concerning from nutritional as well as economical perspective. Although analytical techniques exist for detection of adulterants in oil, most of them require sophisticated instruments, and trained professionals. Microfluidic based lab-on-a-chip technologies have rapidly progressed over the recent years and offer promising alternatives in this regard. In this work, we report development of a paper-based microfluidic lab-on-a-chip for detection of palm oil contamination in sunflower oil. We use the paper-based microfluidic colorimetric detection approach that indicates the presence of adulteration in a visual manner. The data is analyzed using digitally acquired images along with ultraviolet–visible spectrophotometry. The paper-based microfluidic device is fabricated and tested for 10–50% (v/v) palm oil adulteration in sunflower oil. Further, we employ the device for free fatty acid content tests in oil samples. Visual signal acquired from the device is optimized by varying phenolphthalein proportions. The stability of visual colorimetric signal is examined over time and is found to remain steady over the trial period of six days considered in this work. The integration of the detection device with smartphone imaging can prove to be useful for onsite data collection. We believe the approach presented here can be extended to food quality monitoring portable platforms.

There is a relative lack of research on the development of creepage discharge in aged oil-paper insulation subjected to AC-DC combined voltage in converter transformers. In this study, based on the physical and chemical properties of oil-paper, we propose a sphere-plate electrode model to study the creepage discharge parameters and characteristic spectra of aged oil-paper subjected to AC-DC combined voltage. The results show that the creepage discharge inception voltage of aged oil-paper is related to the AC voltage component of the AC-DC combined voltage. However, when the DC voltage component is 60 kV, the flashover phenomenon was found to occur in one of the severely aged samples before the AC voltage was applied. Despite being subjected to the same DC voltage, the flashover phenomenon did not occur in three other samples aged to different degrees. Large-amplitude discharges were found to appear earlier in the severely aged samples. At the same creepage discharge stage, as the aging time of the oil-paper increased, the number of large-amplitude discharges was found to rapidly increase, and the time interval between adjacent discharges was found to gradually decrease. At each stage of the creepage discharge, the small-amplitude discharge has a “hump” shaped distribution. The larger the DC voltage component, the shorter the endurance time of aged oil-paper, and the more severe the damage to the oil-paper. The DC voltage component was found to have an accelerating effect on the development of creepage discharge in aged oil-paper insulation.

Introduction We developed low-cost, portable paper-based diagnostic devices for detection of human immunoglobulin M (IgM) and immunoglobulin G (IgG) in serum without any sample preparation. These devices can be used to help identify presence of diseases, used to provide rapid results ( Materials and Methods We successfully accomplished colorimetric detection of human IgG and human IgM using a sandwich-style assay within the microfluidic paper device via vertical flow immunoassay configuration. The reaction zone in the wax printed paper layer is a small circular pattern. Gold nanoparticles conjugated with anti-human IgG and IgM antibodies have been used for colorimetric detection of IgG or IgM by naked eye. Colorimetric signal can be precisely quantified through implementation of image analysis software which can be developed as an app for a smartphone. The size of the device is 2 cm × 2 cm × 1 mm. Results Colorimetric detection of human IgG was accomplished at 100 fg/mL concentration using a gold nanoparticle–conjugated anti-human IgG antibody. The developed platform has a dynamic range of IgM and IgG concentrations between 0.1 pg/mL and 100 μg/mL. These devices provided a color readout in Conclusions Because of the inherent simplicity of the device operation and their ease of use, there is no variation between samples and users of the device. This low-cost approach enables multiplexing with >1 measurement performed in parallel at the same time. We anticipate that because of the sensitivity, specificity, ease of use, and overall reliability, this approach will become a standard for diagnosis of diseases and health conditions.

This work investigates the influence of blending waste paper and cement at fixed proportion with varying proportions of chicken feather fiber (CFF) and wood saw dust (WSD) as reinforcements. Samples produced were tested for flexural properties and water absorption potentials. The outcome showed that with increasing CFF content and reducing WSD content, water absorption reduced while flexural strength, modulus of ruptures (MOR) and modulus of elasticity (MOE) increases. MOR and MOE were at peaked when the ratio of CFF to WSD was 3:2 while flexural strength reached it crescendo at 4:1 of CFF to WSD. It was noticed that higher CCF content from 3 to 5 wt% gave better results in most of the investigated properties compared to WSD. Therefore, it was concluded that low quantity of WSD is needed to form a synergy with CFF in order to achieve optimum results. Well dispersed CFF-WSD phase in waste paper-cement based composites was observed to be responsible for the enhancement in the investigated properties.

Paper-based diagnostics are leading the field of low-cost, point of care analytical techniques. However, large scale testing facilities such as hospitals are still primarily using the gel column agglutination technique. This is because paper-based systems are single use tests that are generally more time consuming and less automatable than traditional methods. Here, we present a novel, rapid and scalable, paper-based blood typing method that can produce test results in under ten seconds. We believe this is the fastest blood typing test that is appropriate for large scale automation. The test consists of placing a drop of antibody solution on paper, followed by a drop of blood on the same locus, and measuring the evolution of blood stain area as a function of time. Positive reactions for both forward and reverse tests have significantly slower growth rates and smaller final stain sizes when compared to negatives. We analyse the effect paper type, red blood cell concentration, antibody specificity (A, B and D) and antibody dilution have on the sensitivity and reproducibility of the technique. A high sensitivity is found in papers with a low density and thickness. The optimum red blood cell concentration is determined from a balance between wicking rate, strength of reaction and optical contrast. A and B antibodies give more sensitive results than D; however, the D antigen can still be successfully identified. This technique has the potential to significantly cut down the time and cost of blood typing tests and enable design of a new high throughput and fully automatable system.

The present work describes a sensitive, simple, cost-effective and fast analytical procedure to detect the parabens in industrial waste effluent water samples using novel activated carbon nanofiber (CNF) modified filter paper based solid phase extraction technique coupled with liquid chromatography with photodiode array detector (UPLC-PDA). The carbon nanofiber coated filter paper was used as an adsorbent and also characterized by field emission scanning electron microscope (FESEM) showed superior porous structure. Various factors effecting the adsorption and desorption process were studied. The optimum parameters which improve the efficiency are paper length 1 cm × 2 cm, adsorption time 15 min, eluent methanol, eluent volume 5 mL, sample pH 7, desorption time 2 min, 2% salt addition and 300 rpm stirring rate respectively. The parabens exhibited superior linearity ranging from 0.1-50 ng mL-1. The regression coefficient (R2) value ranging from 0.9981-0.9989. This method exhibited good sensitivity with the quantification limit (LOQ) between 0.5-0.75 ng mL-1 and detection limit (LOD) over the range of 0.1-0.25 ng mL-1. The precision was expressed from the RSDs values from 0.74-0.97 %. The spiked analytes revealed excellent recoveries in the range of 95.30-116.72 % with RSD less than 5.72 % for all the water samples also applied for real samples.

Lab-on-paper, or microfluidic paper-based analytical devices (μPADs), use paper as a substrate material, and are patterned with a system of microchannels, reaction zones and sensing elements to perform analysis and detection. The sample transfer in such devices is performed by capillary action. As a result, external driving forces are not required, and hence the size and cost of the device are significantly reduced. Lab-on-paper devices have thus attracted significant attention for point-of-care medical diagnostic purposes in recent years, particularly in less-developed regions of the world lacking medical resources and infrastructures. This review discusses the major advances in lab-on-paper technology for blood analysis and diagnosis in the past five years. The review focuses particularly on the many clinical applications of lab-on-paper devices, including diabetes diagnosis, acute myocardial infarction (AMI) detection, kidney function diagnosis, liver function diagnosis, cholesterol and triglyceride (TG) analysis, sickle-cell disease (SCD) and phenylketonuria (PKU) analysis, virus analysis, C-reactive protein (CRP) analysis, blood ion analysis, cancer factor analysis, and drug analysis. The review commences by introducing the basic transmission principles, fabrication methods, structural characteristics, detection techniques, and sample pretreatment process of modern lab-on-paper devices. A comprehensive review of the most recent applications of lab-on-paper devices to the diagnosis of common human diseases using blood samples is then presented. The review concludes with a brief summary of the main challenges and opportunities facing the lab-on-paper technology field in the coming years.

Highly foldable and flexible energy materials are a requisite for actual applications in self-powered wearable electronics and complex environments. Unfortunately, thermoelectric (TE) materials showing excellent foldability and flexibility under external mechanical stresses have rarely been reported so far. Herein, foldable and flexible TE materials based on Chinese traditional Xuan paper (a bio-based material) and commercialized conducting polymer of poly(3,4-ethylenedioxythiophene):poly(styrene sulfonate) (PEDOT:PSS) are reported. With a facile dip-coating and subsequent drying process, PEDOT:PSS is wrapped on the surfaces of cellulose fibers of Xuan paper via hydrogen-bond interactions. The resulting composite films exhibit outstanding mechanical and decent TE properties. In particular, the PEDOT:PSS/Xuan paper composite films exhibit excellent foldability and flexibility, and can be easily processed into various shapes with no distinct damage to their electrical conductivity and TE performances. This work paves the way for imparting TE performance to insulating paper-based materials, and the unique foldability may widen the TE applications in complex and extreme environments.

Paper-based sensors open a new avenue to produce easy-to-handle, inexpensive and simple-use analytical devices for widespread application fields in biological systems involving diagnosis, drug discovery and biosensing. In this manuscript, we constructed a fluorescence sensor based on functionalized paper coupled with silver nanoparticles (AgNPs) etching for hydrogen peroxide (H2O2) determination in biological systems. A significant fluorescence signal was achieved by immobilizing CDs onto the surface of cellulose filter paper by covalent bonds. The CDs functionalized paper coupled with AgNPs composites platform (PCD/AgNPs) consisted of CDs functionalized paper (PCD) and a AgNPs layer which acted as a fluorescence quencher of CDs via a physical adsorption mechanism. With the introduction of H2O2, the AgNPs were etched accompanied by the fluorescence recovery. As the target, a good linear relationship of a fluorescence turn-on response toward H2O2 between 10 and 120 μM was obtained with a limit of detection of 1.38 μM in our sensor. The designed sensor demonstrated good specificity and would have broad application prospects in the detection of milk samples and determination of H2O2 released from cancer cells.

Detecting vascular endothelial growth factor C (VEGF-C), a kind of tumor biomarker, is of significant clinical importance in evaluating the prognosis of patients with cancer. However, laboratory analyses are usually not suitable for point-of-care testing because they are expensive and time consuming. In response to these challenges, we fabricated an origami paper-based microfluidic electrochemical device. To improve the specificity of VEGF-C detection, nanocomposites, synthesized by new methylene blue (NMB), amino-functional single-walled carbon nanotubes (NH2-SWCNTs), and gold nanoparticles (AuNPs), were used to modify the surface of working electrodes. Results of electrochemical detection showed that the immunosensor had excellent linearity, ranging from 0.01 to 100 ng mL−1 (R2 = 0.988), and the limit of detection was 10 pg mL−1. To confirm the high specificity of the device under real-world conditions, we evaluated the device using clinical serum samples from our hospital. The results demonstrated that the device had an excellent performance and could provide a platform for real-time detection of cancers., Sun, Wang et al. report an origami paper-based immunosensor for the electrochemical detection of the VEGF-C biomarker in blood serum. The immunosensor is made by modifying the surface of working electrodes with new methylene blue, amino-functional single-walled carbon nanotubes, and gold nanoparticles and demonstrates excellent performance with a limit of detection in the range of picograms per milliliter.

Leukocyte esterase (LE) is a useful marker that can be used in establishing a diagnosis of urinary tract infections (UTIs). The development of a UTI diagnostic method with quantitative determinations of biomarkers across all age groups is becoming more important. In this report, microfluidic resistance sensors based on silver ink (Ag ink) and silver ink mixed with ZnO nanoparticles (Ag-ZnO ink) were synthesized and coated on cellulose paper, namely LE-Ag-μPADs and LE-Ag-ZnO-μPADs, respectively, for the sensitive detection of LE. The microfluidic design increases the precision of data and further allows for quantitative determination and early detection of LE in human urine. The quantification of LE relies on the change in the resistance readout coating with Ag ink as well as Ag-ZnO ink in the detection zone. A mixture of 3-(N-tosyl-l-alaninyloxy)-5-phenylpyrrole (PE) and 1-diazo-2-naphthol-4-sulfonic acid (DAS) was deposited in the sample zone to selectively recognize LE, and the resulting nonconductive products, i.e., azo compounds, further reacted with the Ag ink and Ag-ZnO ink to increase resistance. The quantitative detectable LE concentrations between 2 to 32 (×5.2 U mL-1), i.e. ≈12 to 108 μg L-1, cover the commercial dipstick range of trace, +1 and +2. The minimum detectable concentration of LE in urine was 1 (×5.2 U mL-1). The lower concentrations of LE detectable by LE-Ag-μPADs (1-8 × 5.2 U mL-1) are below the value achieved with the ELISA LE kit. Urine samples from inpatients with indwelling urinary catheters were used, and the LE levels measured by the present device were highly correlated with those determined by a commercial urine analyser.

The paper corrugation tube is an innovative kind of energy absorbing structure and shock absorber which can play an important role on the cushioning energy absorption for airdrop equipments and transportation packaging. The deformation characteristics and failure modes of the regular triangle, quadrangle, pentagon and hexagon paper corrugation tubes were comparatively studied by a series of axial static compression experiments, the cushioning energy absorption was evaluated by the seven characteristic parameters (e.g. initial peak force, mean crush force, total energy absorption, specific energy absorption, crush force efficiency, unit area energy absorption and stroke efficiency), and the influences of tube direction, cross-sectional shape, tube length and compression rate on failure modes and cushioning energy absorption were analyzed and compared. These researches showed that the tubes along X direction only have the accordion deformation mode, yet the tubes along Y direction have four deformation modes including steady state progressive buckling, Euler buckling, angular tear and transverse shear. For the paper corrugation tubes along Y direction, the cross-sectional shape has obvious influence on the cushioning energy absorption of structures, and the specific energy absorption and unit area energy absorption of regular triangle and pentagon tubes are better than those of the tubes with regular quadrilateral and hexagonal cross-section at compression rates of 12 and 48mm/min. The tube length of 150 mm or compression rate of 72 mm/min would cause the increase of contribution proportion of non-ideal deformation mode and the decrease of cushioning properties. The paper corrugation tubes along X direction have more stable and controllable deformation mode, yet the paper corrugation tubes along Y direction have better cushioning energy absorption.

The waste of paper or the paper dump is a serious problem and its occurrence is widespread in various institutions. Wastepaper can be recycled to produce some important and usable products that are ecological and biodegradable. For example, it is used to extract new paper from the old by chemical decomposition. Other products such as paper plates, paper cups, paper spoons, tiles, toys, crafts, etc. can be formed from the slurry. This project also initiates a mould that makes cups and plates from the wastepaper management circuit. With learning institutions being the main consumers, most paper are usually eliminated after its use. The waste remains undeveloped and unused, although is a valuable resource. Studying the design of a manual, economical and efficient paper recycling machine, it can be surmised that the design uses the integration of the knowledge gained about the recycling technology that exists manually from the paper recycling machines used to form a cheap but effective paper recycling system. The advantages of the machine are not only of recycled paper, but also the advantages of the interaction of the manual drive system, which will also reduce the high cost. As the design is not 100% effective, the transmission, belt and chain transmission correspond to the estimated 90% efficiency using the 90% for the design. The power consumption for the design is 450 W and since an average user can produce 100 W constant, it takes 5 people to drive the machine.

Wastewater containing heavy metal ions is considered as the serious environmental problem in human society. Adsorption as the widely used method plays an important role in wastewater treatment, which is based on the physical interaction between metal ions and sorbents. Drumsticks are reported to have efficient adsorbing property. It has been found that Moringa causes alteration in testosterone levels, preventing testicular damage and hence is capable of protecting against the toxic effect of hazardous material. Based on this phenomenon of adsorption by Moringa species, we are trying to remove heavy metals from aqueous sample. The bio sorption of heavy metals by non-living biomass of plant origin is an innovative and alternative technology for the removal of the pollutants from aqueous solution and offers several advantages such as low-cost bio sorbents, high efficiency, minimization of chemical and/or biological sludge, and regeneration of the bio sorbent. Moringa oleifera (drumsticks) has a number of advantages including low cost, biodegradable sludge production and lower sludge volume, and also it does not affect the pH of the water. Apart from turbidity removal, Moringa oleifera seeds also possess antimicrobial properties. Amount of adsorption is considerably larger when activated charcoal is used. Thus, this work reports preparation of activated charcoal from drumsticks seeds and fibres. These are generally part of kitchen waste; thus, its preparation and utilisation for heavy metal toxicity not only controls water pollution but also help in reduction of kitchen waste. It will serve as an effective, cheap and robust and green tool for toxicity control. The paper reports the removal of heavy metal (Pb, Ni, Cd, As in this study) by application of prepared activated charcoal tablets via MATLAB assisted paper based sensors. These tablets will surely serve as point-of- care devices for removal of heavy metal toxicity.

We report a simple and cost-effective paper-based and colorimetric dual-mode detection of As(iii) and Pb(ii) based on glucose-functionalized gold nanoparticles under optimized conditions. The paper-based detection of As(iii) and Pb(ii) is based on the change in the signal intensity of AuNPs/Glu fabricated on a paper substrate after the deposition of the analyte using a smartphone, followed by processing with the ImageJ software. The colorimetric method is based on the change in the color and the red shift of the localized surface plasmon resonance (LSPR) absorption band of AuNPs/Glu in the region of 200-800 nm. The red shift (Δ

In recent years there has been increasing interest in the use of recycled paper waste in the production of concrete to reduce environmental pollution. This study aims to investigate the use of raw paper waste to produce lightweight cement mortar and to study the effect of the aluminium sulphate treatment of raw paper waste on the compressive strength, absorption ratio and hardened density of mortar. This study used raw paper waste as a replacement for fine aggregate, with percentages of 5%, 10%, 15%, 20% and 30%. The same percentages were examined for the aluminium-sulphate-treated paper waste. The study aims to achieve a similar workability and fixed flow rate for all mixes; therefore, the water–cement ratios were changed for mixes containing paper waste to balance the water absorbed by the paper waste. The study found that the treatment of paper waste with aluminium sulphate helps to reduce the amount of water absorbed by the paper waste and also reduces the amount of water required to maintain its workability, with a higher paper-waste content requiring a larger water content to achieve a similar workability. It was found that the higher the paper-waste content, the lower the wet and dry densities. The compressive strength at both an early and mature age decreased with the increased content of paper waste. Finally, the treatment of paper waste with aluminium sulphate increases the early age compressive strength for similar replacement percentages of up to 19%.

Cyanide ( CN - ) is a deleterious chemical and can cause serious health effects upon exposure even at low concentrations. Different sensors have been developed to monitor cyanide in water, which, however, suffers from complex mechanisms and high-cost. Curcuma longa or turmeric is a commercially available natural dye (usually in powder form) used as medicine. The phenolic substance curcumin is responsible for its yellow color and is capable of sensing environmentally significant analytes such as CN - . In this study, a colorimetric sensor for cyanide in aqueous solution was fabricated by the immobilization of crude curcumin on ordinary filter paper. The curcumin was extracted from locally available turmeric powder using a simple extraction method. Its successful integration in the filter paper was validated by FT-IR spectroscopy. UV–Vis analysis showed that the curcumin-based paper sensor was sensitive to CN - (down to 5.0 ppm), producing a visual change from yellow to dark red. The fabricated sensor also demonstrated high selectivity towards CN - in the presence of N a + , K + , and F - . Its response time was found to be inversely proportional to the concentration of the CN - in the solution. Assessment of reusability revealed that the sensor was reusable for up 8 cycles before significant changes in colorimetric response were observed. Importantly, the fabricated sensor exhibited applicability for actual cyanide monitoring in real water samples.

Infectious diseases cause millions of deaths annually in the developing world. Recently, microfluidic paper-based analytical devices (μPADs) have been developed to diagnose such diseases, as these tests are low cost, biocompatible, and simple to fabricate. However, current μPADs are difficult to use in resource-limited areas due to their reliance on external instrumentation to measure and analyze the test results. In this work, we propose an electricity and external instrumentation-free μPAD sensor based on the colorimetric enzyme-linked immunosorbent assay (ELISA) for the diagnosis of infectious disease (3D-tPADs). Designed based on the principle of origami, the proposed μPAD enables the sequential steps of the colorimetric ELISA test to be completed in just ∼10 min. In addition, in order to obtain an accurate ELISA result without using any instrument, we have integrated an electricity-free "timer" within the μPAD that can be controlled by the buffer viscosity and fluid path volume to indicate the appropriate times for washing and color development steps, which can avoid false positive or false negative results caused by an extended or shortened amount of washing and development times. Due to the low background noise and high positive signal intensity of the μPAD, positive and negative detection results can be distinguished by just the naked eye. Furthermore, the ELISA result can be semi-quantified by comparing the results shown on the μPAD with a color chart diagram with a detection limit of HIV type 1(HIV-1) p24 antigen as low as 0.03 ng mL-1. These results demonstrate the proposed sensor can perform infectious disease diagnosis without external instrumentation or electricity, extending the application of the μPAD test for on-site detection and use in resource-limited settings.

Cellulose bromo-isobutyl ester was prepared using filter paper as raw material through esterification reaction with 2-Bromoisobutyryl bromide (BIBB) in N, N-Dimethyl-formamide (DMF). Cellulose esters with different degree of substitution were obtained. FTIR result indicated the successful introduction of bromo isobutyryl group in cellulose to obtain cellulose ester (Cell-Br). The surface of modified filter paper become rough and grooves could be observed by SEM. The thermal stability of the cellulose ester decreased in comparison with unmodified filter paper. Besides, the hydrophobicity of the filter paper was improved and the water contact angle increased from 73.4° to 116.5° with increasing degree of substitution. The water vapor barrier property was improved by 26 %. Furthermore, it was also found the modified filter paper possessed antibacterial activity against S. aureus bacteria. The modified filter paper obtained could be potentially used in food packaging fields and the results provide a simple method to prepare functional filter paper.

In China, Xuan paper has been the paper of choice as artwork support and for conservation, for several centuries. However, little is known about its material properties, especially given the many grades of sized and unsized Xuan paper. In addition, there is a lack of information on its degradation. In this research, a selection of contemporary unsized Xuan papers was investigated, representing diverse raw materials. Seven out of twelve contemporary unsized Xuan papers were determined to be approximately neutral and contain > 2% alkaline reserve, indicating good durability. Viscometry was used to determine the degree of polymerisation (DP) as none of the samples gave significant reactions to the phloroglucinol spot test. The average DP of ten contemporary unsized Xuan papers is ~ 1700, excluding two papers that have presumably been sun-bleached, and that exhibit significantly lower DP. Using X-ray fluorescence, it can be demonstrated that Ca and Si are the dominant elements and interestingly, Ca content is directly correlated with ash content and with alkaline reserve. Accelerated degradation was performed at two sets of environmental conditions, i.e. 90 °C, 30% RH and 60 °C, 70% RH, and the established degradation rates agreed with the Collections Demography model of paper degradation meaning that degradation of Xuan papers proceeds in the same way as other types of paper. This research gives fundamental insights into contemporary unsized Xuan papers, which exhibit good stability during accelerated degradation despite the low starting DP in the context of the samples used in this study. Our findings may inform methods of Xuan paper production, selection of Xuan paper for conservation purposes, as well as preventive conservation of Xuan paper-based artefacts.

Paper money was first used in China as early as the sixth century AD. Since that time, counterfeits have circulated in parallel with authentic paper money. After WWII the interest of art collectors in historical emergency paper money surged and counterfeiting became a complex phenomenon. In fact, the use of scientific investigation for determining the authenticity of historical paper money is still limited to few cases. In this work nine pieces of Chinese paper money (from the fourteenth to nineteenth century) were investigated by combining non-invasive MA-XRF imaging and Raman spectroscopy. Analytical results on the paper money demonstrated how the complementary use of both non-invasive techniques can provide an excellent tool for discriminating modern materials from historical ones, allowing us to identify seven counterfeits in the set of nine investigated paper moneys.

There is a pressing need around the world to develop novel functional biodegradable materials to separate oil/water mixtures and emulsions completely. Recently, superhydrophilicity and underwater superoleophobicity materials have been attracted attention due to their high efficiency in oil/water separation. However, it is still a challenge to prepare materials that combine oil/water separation and water purification in an environment-friendly way. In this work, biodegradable starch-based nanospheres (SNPs) coated filter paper was prepared in a low-cost, simple, and environmentally friendly manner. The SNPs coating could not only help to change the wettability of the substrate material but also build the hierarchical micro and nano structures which are conducive to separation and purification process. After modification by coating SNPs, the filter paper exhibited excellent performance in a wide range of oil/water mixtures or emulsions separation and the wettability of the filter paper could be regulated by adjusting the pH value. The modified filter paper presented good recyclability after several separation process. Furthermore, the as-prepared filter paper could also remove water-soluble contaminants during the oil/water separation process, thus realizing to combine separation and purification process in one single step. This biodegradable starch-based separating material with good separation performance, stability and recyclability has significant application potential in practical separation and purification process.

Paper mulberry, a fast-growing and vigorous plant, is a potential substrate for producing lignocellulosic bioethanol and an important renewable alternative to fossil fuels. In order to improve the economic feasibility of ethanol production from paper mulberry, H3PO4/H2O2 pretreatment was selected as the most suitable pretreatment method that could produce the highest glucose concentration (131 g/L) compared with other pretreatments (73.2–89.3 g/L) at high solid loading. Whereafter, the final solid loading of H3PO4/H2O2 pretreatment was significantly increased to 40% (w/v) without any decrease in the final glucose concentration. Finally, a novel Fed-nonisothermal-simultaneous saccharification and fermentation was constructed using H3PO4/H2O2 pretreated paper mulberry, which bypassed the inhibition caused by paper mulberry solid and high temperature on the traditional simultaneous saccharification and fermentation, improving ethanol concentration (63.9 g/L), ethanol productivity (1.33 g/L/h) and ethanol yield (0.160 g/g-biomass) by 30.4%, 30.4% and 30.1%, respectively, compared to those obtained from SSF (simultaneous saccharification and fermentation) process. Thus, we have opened up a novel way to produce ethanol or other biofuels using the paper mulberry as an outstanding alternative substrate.

Starch and derivatives thereof have proven their usefulness in paper coating processes. Among these derivatives, cationic starch has been widely used in the paper industry as a flocculation, dispersion and ink fixing agent. In another context, nanoscale cellulosic materials have been shown to improve the strength, retention of fillers, the barrier properties of packaging paper products, and printing qualities. This review summarizes the recent studies on the general components used in paper coating, describes the conventional and alternative synthetic processes of cationic starches and nanocellulose, and deals with their current and potential applications in papermaking, focusing primarily on surface treatments. Moreover, environmental applications have been considered to expand the understanding and usefulness of these materials. Further research on modified polysaccharides is encouraged to replace, in a feasible way, petro-based components of coating formulations, and to provide paper surfaces with new properties.

Process-monitoring laboratories in the pulp and paper industry generally use a combination of wet chemical analyses and physical measurements to certify the fitness of a production pulp for a specific end-use. These laboratory tests require time and the effort of trained personnel, limiting their utility for real-time process control. Here we show that Raman probes of unrefined cellulosic pulps, well-suited to the online measurement of in-process materials, can predict the quality attributes of manufactured papers. The accuracy of prediction improves when the covariance is modelled in a reduced measurement space selected by a data-driven, feature-selection technique referred to as a Template Oriented Genetic Algorithm (TOGA). TOGA, combined with discrete wavelet transform (DWT), isolates functional-group features that correlate best with mechanical properties paper derived from refined pulp. Paper makers refine market pulps to build sheet strength using a beating process that decreases freeness as it increases fibre-fibre bonding. Methods demonstrated here predict manufactured sheet properties obtainable after any specified degree of refining from the Raman spectrum of an unrefined pulp. This analysis capacity will enable both vendors of market pulp and makers of sheet paper to specify in advance the amount of beating required to produce a desired product, thereby saving cost and conserving resources.

The paper industry wastewater even after bio-treatment at industrial scale is a major source of aquatic and soil pollution due to various unknown compounds. Hence, the study has focused on the detection of residual organic pollutants from the bleached and unbleached paper mill wastewater and both sources showed endocrine-disrupting compounds. The toxicity test with Phaseolus aureus seed germination showed inhibition of seed germination and alpha-amylase activity >25% in bleached and unbleached paper mill wastewater. The LC50 of Tubifex tubifex was noted of >50% after 48 hours incubation test. This revealed that the wastewater discharged from bleached paper mill is more toxic than unbleached paper mill waste this might be due to the use of more chemicals during bleaching and pulping process. This study has revealed that there is need to treat both paper mill wastewaters adequately prior to discharge.

Eco-friendly and cost-effective materials and processes to manufacture functional substrates are crucial to further advance the area of printed electronics. One potential key component in the printed electronics platform is an electrically functionalized paper, produced by simply mixing common cellulosic pulp fibers with high-performance electroactive materials. Herein, an electronic paper including nanographite has been prepared using a standardized and scalable papermaking technique. No retention aid was needed to achieve a conducting nanographite loading as high as 50 wt %. The spontaneous retention that provides the integrity and stability of the nanographite paper, likely originates partially from an observed water-stable adhesion of nanographite flakes onto the fiber surfaces. The resulting paper exhibits excellent electrical characteristics, such as an in-plane conductivity of 107 S/cm and an areal capacitance of 9.2 mF/cm(2), and was explored as the back-electrode in printed electrochromic displays. Funding Agencies|Digital Cellulose Centre, a competence center set up by the Swedish Innovation Agency VINNOVA; consortium of Swedish forest industries; Wallenberg Wood Science Center (Knut and Alice Wallenberg Foundation); VINNOVA "EPIC" projectVinnova [2017-05413]; Karl-Erik Onnesjo Foundation

An industry compatible chemo-refining approach was tested for preparation of micro-nanofibrillated cellulose (MNFC) from bleached softwood pulp using sodium meta-periodate and sodium chlorite as oxidizers followed by refining in Valley beater. SEM and FTIR analyses confirmed micro-nano scale fibrillation and chemical functional group modification in laboratory prepared MNFC, respectively. The water retention value, carboxyl content and viscosity of MNFC were found comparable with imported NFC as reference (R-NFC). To evaluate MNFC as strength enhancer for paper properties, 5% MNFC addition to bleached mixed hardwood pulp showed 6% reduction in bulk with 36%, 24% and 97% increment in breaking length, burst index and double fold of the handsheets, respectively without affecting tear index and optical properties than the control. Surface properties were also improved. Pulp drainability (37°SR) after MNFC addition was found suitable for papermaking. These laboratory results confirmed the potential of MNFC as a suitable strength additive for paper quality improvement.