Search

The paper presents the results of a study of parameters used for determining the amount of organic pollutants in wastewater flowing into a collective wastewater treatment plant with a population equivalent of about 120 000 PE. The plant constituted part of a sewage system. Assays were performed for biochemical oxygen demand (BOD5), chemical oxygen demand (CODCr), permanganete index (CODMn) and total organic carbon (TOC). In addition, the pH of wastewater and its alkalinity were determined. Sampling of incoming wastewater and measurement of physicochemical parameters were performed once a week, in the spring. A total of 44 samples of wastewater were collected. The correlations between the individual parameters and the correlations between the ratios of these parameters were determined. It was found that it was possible to estimate, with suffi cient accuracy, the values of selected parameters for determining the concentrations of organic compounds in municipal wastewater, knowing the values of other parameters in this group. Moreover, it was shown that, knowing the relationship between the analyzed parameters, one can find multiple regression equations for a given type of wastewater, which allow one to calculate the remaining relationships with a good fit, i.e. a determination factor R2greater than 0.6

In this paper, we analysed the pollutant removal efficiency and reliability of a vertical and horizontal flow hybrid constructed wetland (CW) planted with giant miscanthus and Jerusalem artichoke. The wastewater treatment plant, located in south-eastern Poland, treated domestic sewage at an average flow rate of 1.2 m3·d−1. The tests were carried out during. 5-years of operation of the sewage treatment plant (2011–2016). During this period, sewage samples were collected from three stages of wastewater treatment in four seasons (winter – February, spring – May, summer – August, and autumn – November). The following parameters were measured: BOD5, COD, total suspended solids, total nitrogen, and total phosphorus. The average effectiveness of organic pollutant removal expressed by BOD5 and COD was 98.8 and 97.6%, respectively, and the removal efficiency for total suspended solids was 93%. The average values of BOD5, COD, and total suspended solids in wastewater discharged to the receiver were significantly lower than the limit values required in Poland. The efficiency of total nitrogen and total phosphorus removal was 64.1 and 68.1%, respectively, and the average values of these components in the outflow from the treatment plant exceeded the standard levels. A reliability analysis performed using the Weibull probability model showed that the reliability of pollutant removal in the tested CW system was very high for BOD5 and COD (100%). It was also demonstrated that the tested CW did not provide effective elimination of biogenic elements (nitrogen and phosphorus), as evidenced by the low reliability values – 32 and 28%, respectively. The investigated hybrid CW system with giant miscanthus and Jerusalem artichoke removed organic and biogenic pollutants with a similar efficiency as systems using classic plant species such as reed and willow.

This paper is a review of research and experiences related to the application of constructed wetland systems (CWs) in southeastern Poland in 1992–2016. On the basis of literature data, a comparison between pollutant removal efficiencies of one-stage and hybrid CWs was made. Some problems regarding the operation of these treatment plants were also presented. Data from various facilities indicate that one-stage CWs with horizontal or vertical flow were characterised by a quite high (80–89%) efficiency of removal of BOD5, COD and total suspended solids, but were less efficient in removing of biogenic compounds nitrogen and phosphorus – respectively 59 and 66%. Significantly higher removal efficiencies for the basic pollutants (above 92%) were observed in hybrid CWs with a VF–HF bed configuration. Those facilities removed ca. 65% of total nitrogen and 89% of total phosphorus. A statistical analysis revealed that hybrid VF–HF type CWs were characterised by a very high, about 99%, operation reliability. Lower reliabilities were achieved by one-stage CWs, especially those with a VF bed. Twenty five years of research on and experiences in the application of CWs in southeastern Poland indicate that one-stage CWs can be used on a larger scale in Polish conditions in rural areas with a scattered housing structure. Hybrid systems, on the other hand, can be applied successfully in recreational centres or in protected areas, especially in national parks, where a high pollutant removal efficiency is required. It has been shown that the use of hybrid CWs is consistent with the idea of sustainable development.

The results of research on the efficiency and technological reliability of domestic wastewater purification in two household wastewater treatment plants (WWTPs) with activated sludge are presented in this paper. The studied facilities were located in the territory of the Roztocze National Park (Poland). The mean wastewater flow rate in the WWTPs was 1.0 and 1.6 m3/day. In 2017–2019, 20 series of analyses were done, and 40 wastewater samples were taken. On the basis of the received results, the efficiency of basic pollutant removal was determined. The technological reliability of the tested facilities was specified using the Weibull method. The average removal efficiencies for the biochemical oxygen demand in 5 days (BOD5) and chemical oxygen demand (COD) were 66–83% and 62–65%, respectively. Much lower effects were obtained for total suspended solids (TSS) and amounted to 17–48%, while the efficiency of total phosphorus (TP) and total nitrogen (TN) removal did not exceed 34%. The analyzed systems were characterized by the reliability of TSS, BOD5, and COD removal at the level of 76–96%. However, the reliability of TN and TP elimination was less than 5%. Thus, in the case of biogenic compounds, the analyzed systems did not guarantee that the quality of treated wastewater would meet the requirements of the Polish law during any period of operation. This disqualifies the discussed technological solution in terms of its wide application in protected areas and near lakes, where the requirements for nitrogen and phosphorus removal are high.

The paper presents the results of a 3-year study on the technological reliability and the efficiency of typical domestic wastewater treatment in two hybrid constructed wetland systems (CWs) located in the area of the Roztocze National Park (Poland). The studied objects consist of an initial settling tank and a system of two beds of the vertical flow (VF) and horizontal flow (HF) (VF&ndash, HF) type with reed and willow. The wastewater flow rate in the constructed wetlands systems (CWs) was 0.4 and 1.0 m3/d, respectively. During the study period (2017&ndash, 2019) 20 series of analyses were performed and 60 wastewater samples were collected. Based on the obtained results the effects of pollutant removal and the technological reliability were determined, which were specified with the Weibull method. The average efficiency of biochemical oxygen demand (BOD5) and chemical oxygen demand (COD) removal was 96&ndash, 99%. Slightly lower effects were obtained in the case of total phosphorus (TP) removal (90&ndash, 94%), as well as for total suspended solids (TSS) (80&ndash, 87%) and total nitrogen (TN) (73&ndash, 86%) removal. The analysed CWs were characterised by 100% technological reliability for BOD5 and COD, as well as a good reliability for TSS and TP (87&ndash, 100%) but slightly lower for TN removal (35&ndash, 89%). Hybrid CWs of VF&ndash, HF type should be recommended to use in protected areas for wastewater treatment and water resources quality protection.

The paper presents the results of a study of selected parameters of common osier (Salix viminalis) biomass sampled annually, over a 12-year period, from a constructed wetland wastewater treatment plant. The focus of the study was on parameters that were relevant to biomass energy management. The study was conducted in a constructed wetland wastewater treatment plant consisting of one horizontal flow bed with a total area of 186 m2, planted with osier willows. The following biomass parameters were analysed: biomass yield, volume, humidity, ash content, higher and lower heating values, and contents of N, P, K in different parts of plant stems. The study showed that osier biomass harvested from the investigated constructed wetland system could be used as an energy source in thermochemical processes. The higher and lower heating values were similar to those obtained by other authors (18.13 and 17.38 MJ·kg−1, respectively). The energy yield (17.49 MJ·m−2) and energy density (3486–5411 MJ·m−3) were also calculated. Young shoot parts had higher ash and micronutrient contents and lower energy parameters than old parts.

Recent years have seen an increasing interest in hybrid constructed wetland (HCW) systems for domestic sewage treatment. This paper is focused on kinetics of removal of the main pollutants occurring in wastewater i.e. organics expressed as chemical oxygen demand, biochemical oxygen demand and total nitrogen. The purpose of the article is to compare different HCW configurations in terms of mass removal rates (MRR) and removal rate coefficients (kA and kv). Analysed data have been collected at two wetland systems, each composed by two subsurface flow beds: horizontal flow (HF) and vertical flow (VF). Reliable evaluation was achieved by using the same composition of influent wastewater in both HCWs. Performance of opposite configurations HF + VF vs. VF + HF was compared after each stage and the overall HCW system. The average mass removal rates of COD, BOD5 and TN in both systems were similar, respectively: 2.30, 0.98 and 0.40 g m−2 d−1. However, removal rates differ between single wetland beds after each treatment stage.

The paper presents the results of a study of the reliability and efficiency of pollutant removal during long term operation of a one-stage constructed wetland system with horizontal flow. The flow rate of the wastewater treatment plant was 1.2 m 3 d −1 during the research period. Physical and chemical analyses of raw wastewater and treated effluent were carried out in the years 1997–2010 (14 years). During this study period, 56 series of analyses were performed and 112 wastewater samples were collected. The average efficiencies of BOD 5 (Biochemical Oxygen Demand), COD (Chemical Oxygen Demand) and TSS (Total Suspended Solids) removal in the investigated facility during the 14 years of its operation were respectively: 84.7%, 80.9%, and 62.4%. The average values of these parameters in the treated wastewater were significantly lower than the values deemed acceptable by relevant regulations in Poland. The reliabilities of the wastewater treatment plant, based on the Weibull reliability theory for acceptable values of pollution parameters in the effluent of the treatment plant, were as follows: BOD 5 – 92%, COD – 98%, TSS – 90%. The conducted analysis showed that the operational reliability of the one-stage horizontal subsurface flow constructed wetland (HSFCW) over the operation period was insufficient according to the Polish standards. Improvement of the reliability of the analyzed system by introduction of additional purification elements, such as irrigated biological beds or a constructed wetland with vertical wastewater flow, was recommended.

The study investigated the efficiency of removal of iron, manganese and indicator bacteria from potable groundwater by using carbonate-silica rock (opoka). The tests were performed in a laboratory in three filter columns supplied with water containing increased concentrations of iron and manganese. Two of the columns were filled with carbonate-silica rock with particle sizes of 2-5 mm; retention time for water in the columns was set at 1 h and 2 h. A third column was filled with 1-2 mm rock particles, with hydraulic retention time set at 1 h. High removal efficiencies were determined for iron, manganese and coliform bacteria and low removal efficiencies for psychro- and mesophilic bacteria. An increase in the alkalinity of the investigated water was also observed.

The goal of this paper was to evaluate the possibility of using terrestrial laser scanning (TLS) for inventorying of a hybrid constructed wetland (CW) wastewater treatment plant. The object under study was a turtle-shaped system built in 2015 in Eastern Poland. Its main purpose is the treatment of wastewater from the Museum and Education Centre of Polesie National Park. The study showed that the CW system had been built in compliance with the technical documentation, as differences between values obtained from the object and those given in the design project (max. ± 20 cm for situation and ±5 cm for elevation) were within the range defined by the legislator. It was also shown that the results were sufficiently precise to be used for as-built surveying of the aboveground elements of the CW system. The TLS technique can also be employed to analyse quantitative changes in object geometry arising during long-term use (e.g. landmass slides or erosion), the identification of which can help in selecting the hot-spots at risk of damage and thus restore the object to its original state as well as prevent new changes.

The aim of the present study was to assess the technological reliability of a domestic hybrid wastewater treatment installation consisting of a classic three-chambered (volume 6 m3) septic tank, a vertical flow trickling bed filled with granules of a calcinated clay material (KERAMZYT), a special wetland bed constructed on a slope, and a permeable pond used as a receiver. The test treatment plant was located at a mountain eco-tourist farm on the periphery of the spa municipality of Krynica-Zdrój, Poland. The plant's operational reliability in reducing the concentration of organic matter, measured as biochemical oxygen demand (BOD5) and chemical oxygen demand (COD), was 100% when modelled by both the Weibull and the lognormal distributions. The respective reliability values for total nitrogen removal were 76.8% and 77.0%, total suspended solids – 99.5% and 92.6%, and PO4-P – 98.2% and 95.2%, with the differences being negligible. The installation was characterized by a very high level of technological reliability when compared with other solutions of this type. The Weibull method employed for statistical evaluation of technological reliability can also be used for comparison purposes. From the ecological perspective, the facility presented in the study has proven to be an effective tool for protecting local aquifer areas.

The paper presents the results of application of hydrogen peroxide (H2O2) for the optimization of the effects of ammonia nitrogen removal from domestic wastewater. The investigations were carried out at a model wastewater treatment plant consisting of a preliminary sedimentation tank and a sand filter with a horizontal flow of wastewater at a constant hydraulic load of 1.44 L/day. The efficiency of ammonia nitrogen removal was analyzed for different wastewater oxygenation levels: 0–10%, 10–20%, 20–30%, 30–40% and 40–50%, maintained by controlled application of a 0.1% H2O2 solution. It was demonstrated that the gradual increase in oxygen concentration in treated wastewater due to H2O2 dosing resulted in an increase in ammonia nitrogen removal from 39.0 to 81.2%. The best removal efficiency was obtained when the oxygenation level was in the range of 30–40%. It was also shown that application of hydrogen peroxide resulted in an effective removal of biochemical oxygen demand (BOD5). The highest BOD5 removal efficiency (94.3%) was obtained at the oxygenation level of 30–40%. The results indicate that oxygenation of wastewater with hydrogen peroxide can be applied for the optimization of the nitrification process in wastewater treatment plants.

The aim of study was the analyze of the reliability pollution removal in wastewater treatment plant in Mińsk Mazowiecki. The article presents the results of the reliability of BOD, COD and total suspended solids removal of wastewater treatment plant with actived sludge. Physical and chemical analyses of raw wastewater and treated effluent were carried out in the years 2016–2017 (2 years). The designed size of the treatment plant with actived sludge, expressed in PE is 82 200 residents. During this study period, 50 wastewater samples were collected and analyses. For each of pollution indicators descriptive statistic, percentage reduction and and treatment plant reliability factors (WN) were calculated. The average effectiveness of BOD5 (Biochemical Oxygen Demand), CODCr (Chemical Oxygen Demand) and TSS (Total Suspended Solid) removal in this period of study were respectively: 99.1%, 96.3% and 98.9%. A reliability analysis was performed using the Weibull probability model.

tThe aim of the study was to determine the influence of the particle size of carbonate–silica rock (opoka)used in rock filters on the efficiency of phosphorus removal from domestic wastewater. The investigationswere carried out in a laboratory using a model consisting of three vertical flow filters with carbonate–silicarock of different particle sizes (G1= 1–2 mm; G2= 2–5 mm; G3= 5–10 mm). The tested rock was subjectedto decarbonising at 900◦C and consisted primarily of 51.7% SiO2, 23.2% CaO, and 7.6% Al2O3. In the firstthree weeks of the study (1–3), the hydraulic load of each filter was Q1= 0.72 l/day and the hydraulicresidence time was HRT1= 24 h; in the next three weeks (4–6) Q2= 1.08 l/day and HRT2= 16 h, and duringthe last three weeks (7–9) Q3= 1.44 l/day and HRT3= 12 h. A significant influence of the size of rock parti-cles and the hydraulic load (hydraulic residence time) on the efficiency of total phosphorus removal andon phosphorus concentration in the wastewater discharged from the system was observed ( = 0.05).Statistically, the best removal of phosphorus from wastewater – an average of 97%, was found in thesubstrate with the smallest particle size (rock G1, 1–2 mm) at the lowest hydraulic load of 0.72 l/dayand at a hydraulic residence time of 24 h. The lowest phosphorus removal efficiency was observed inthe filter containing rock G3with a particle size of 5–10 mm (mean

Under conditions of low funding for the production of “green energy” in Poland, it became necessary to search for other – cheaper sources of biomass and the development of more efficient technologies. The maize straw is waste material arising in the production of grain. Therefore currently has no wider application and the cost of acquisition is several times lower than in case of maize silage. This paper presents the results of research on biogas efficiency of the maize straw silage, the dynamics of the fermentation process and the decomposition time of biomass under the meso- and thermophilic conditions. Moreover, the exploitation costs of a biogas plant working on this substrate and maize silage have been compared. It has been proved that thermophilic fermentation is significantly shorter (17%) than mesophilic and permits to increase biogas production (8.6%) and methane content (9.3%). In turn, mesophilic fermentation has more stable pH changes in comparison with the thermophilic technology. However, it is related to inhibition of the propionic acid, which can be of great importance in case of continuous fermentation. On the basis of energetic calculations it was shown that the substitution of the maize silage with the maize straw silage allows for nearly three-fold costs reduction and thus increase of the biogas plant profitability.

In recent years, constructed wetland systems are used widely for the purification of small amounts of wastewater because they provide very high effects of removing impurities. The existing research results show that constructed wetland systems can be used not only for highly efficient wastewater treatment, but at the same time in order to produce biomass for energy purposes. The aim of this paper was to determine the possibilities of energy use of the plants: common reed, willow, Jerusalem artichoke, giant miscanthus, obtained from constructed wetland system. The yield of common reed was the highest compared to the other plant species used in analyzed object and amounted to 13.6 Mg DM ha −1 and then 8.7 Mg DM ha −1 for willow. The lowest dry matter yield was 5.9 Mg DM ha −1 in the case of Jerusalem artichoke. High Heating Value was similar in all analyzed plants (17.9–19.2 MJ kg −1 ), the highest results were obtained from willow. Biomethane production during anaerobic digestion was the highest from common reed (108 m 3 Mg −1 FM) and the lowest from Jerusalem artichoke (66 m 3 Mg −1 FM). The methane concentration in biogas was rather low (50.9–54.9) comparing to other typical substrates for biogas production.

The present paper reports pollutant removal efficiencies and reliability for a four-stage hybrid constructed wetland (HCW) consisting of the following sequence of subsurface (SS), vertical flow (VF) and horizontal flow (HF) beds: SSVF-SSHF-SSHF-SSVF. The experiments were carried out over a period of three years, with sampling done in each season: winter, spring, summer and autumn. Grab samples of wastewater collected from different stages of treatment were tested for total suspended solids (TSS), BOD5, COD, total nitrogen (TN) and total phosphorus (TP). The wetland was found to have a very high efficiency of removal of suspended solids and organics, with relatively little seasonal variability. The three-year average TSS removal efficiency was approximately 92.7%. The effectiveness of elimination of organic compounds was very high throughout the study period at 96.6% BOD5 and 95% COD. The effluent from the four-stage system had significantly lower contents of TN and TP compared to the wastewater discharged from the first two beds of this facility.

This paper reports a comparative study on kinetics of organic matter expressed as BOD5 and nitrogen removal in constructed wetlands operated in Poland. Analyzed data were collected at eight wetland systems, composed of subsurface flow beds: horizontal flow (HF) and vertical flow (VF), in different number and sequences. The analysis involved particularly mass removal rates (MRR) and first-order removal rate coefficients of BOD5 and total nitrogen (kA and kv for VF and HF filters, respectively, and k20 as a parameter averaged for a temperature of 20 °C). It was found that the higher the load of pollutants applied to the beds, the higher MRR values were obtained. The average k-rates in analyzed systems were mostly lower than those reported in the literature, especially in the case of total nitrogen. Its removal obtained in horizontal flow beds was kv = 0.002–0.042 d−1, while in vertical flow systems kA varied from 0.007 m d−1 to 0.0037 m d−1. According to data given by previous studies, first-order reaction rates for nitrogen removal varied in range from kv = 0.048 d−1 to kv = 0.19 d−1 and kA from 0.007 to 0.1 m d−1 in HF and VF beds, respectively. Regarding BOD5 shown in literature, removal rate kv for HF beds varied from 0.071 to 6.11 d−1, and kA for VF beds varied from 0.019 to 1.0 m d−1, while in this study lower k-rates were obtained: kv = 0.005–0.085 d−1 and kA = 0.015–0.130 m d−1. Relatively long monitoring period, for some of constructed wetland up to 16 years, resulted in good data set and enables creation of the graphs, which could be helpful in evaluation and designing of constructed wetlands for PE bigger than 50, in moderate climate conditions.

The aim of this work was to determine the potential of phytoremediation of Vetiveria zizanioides and Oryza sativa to nitrate (NO3−-N) and organic matter (COD – chemical oxygen demand) removal in subsurface vertical flow constructed wetland systems (VFCWs). The tests were carried out in models of 2 beds with a surface of 0.24 m2 and depth 0.70 m each at various hydraulic loads (HL) and COD constant in influente wastewater. The VFCW-1 bed was planted with the Vetiveria zizanioides and the VFCW-2 bed with the Oryza sativa. During the 22 weeks of research, the hydraulic load of the analyzed beds was: HL1 = 148 dm3·m−2·d−1, HL2 = 239 dm3·m−2·d−1, HL3 = 350 dm3·m−2·d−1, HL4 = 473 dm3·m−2·d−1. The VFCWs were fed from two reservoirs, one with mineral medium and nitrate, and the other one with fructose as organic matter. Based on the conducted tests, it was found that in both analyzed systems (VFCW-1 and VFCW-2) the highest NO3−-N removal rate was found under HL2 – the median is 59 and 42% respectively. The most effective removal of COD in the VFCW-1 system was obtained at a HL2 – 55%, while in the system VFCW-2 at a HL1 – 43%. The research shows that the low HL and high COD/NO3−-N ratio ensures good effects of nitrate and organic matter removal in VF type constructed wetland systems. It has been shown that the analyzed plants, especially Vetiveria zizanioides have good phytoremediation potential in the field of nitrate nitrogen and organic substance removal and can be recommended for use on a full scale of technology.

The aim of the study was to evaluate the nitrogen removal and its effects on the plant’s growth and leaves morphology. using two subsurface vertical flow (VF bed), with different depths (0.24 m2 × 0.70 m; 0.24 m2 × 0.35 m) and nitrogen load increments. The VF bed were planted with Vetiveria zizanioides, filled with light expanded clay aggregates (Leca®NR 10/20) and fed in parallel mode with synthetic wastewater. High ammonium nitrogen concentration ([NH4 +–N] from 68 ± 3 to 290 ± 8 mg L−1) was used without toxicity symptoms in plants, although the effects of ammonium nitrogen load were stopped the growth of the plants. Significant differences between ammonium nitrogen removed in each VF bed obtained for total nitrogen (TNinfl.) ≥ 27 ± 0.8 g m−2 d−1. The nitrification was contributed to ammonium nitrogen removal because was found higher values of nitrate and nitrite in the effluent. These values were more higher in VF bed 1 than in the VF bed 2, since ammonium nitrogen removal were also more higher in VF bed 1 than in the VF bed 2. Total nitrogen mass balance was carried out and the results show that the nitrification/denitrification process occurred with nitrogen plants uptake. It was observed that the VF bed depth has an influence on all nitrogen removal processes. As higher the depth root system it is seemed to favour the creation of zones with different oxidations conditions that allow the nitrogen compounds to be removed intensively.

In this paper, the pollutant removal efficiency and the reliability of a vertical and horizontal flow hybrid constructed wetland (CW) planted with common reed, manna grass, and Virginia mallow were analyzed. The wastewater treatment plant, located in south-eastern Poland, treated domestic sewage at an average flow rate of 2.5 m3/d. The tests were carried out during five years of its operation (2014&ndash, 2018). The following parameters were measured: biochemical oxygen demand (BOD5), chemical oxygen demand (COD), total suspended solids, total nitrogen, and total phosphorus. The results showed that more than 95% of BOD5, COD, and total phosphorus was removed in the tested CW system. The average effectiveness of removal of total suspended solids and total nitrogen exceeded 86%. A reliability analysis performed using the Weibull probability model showed that the removal reliability in the tested CW was very high for BOD5, COD, total suspended solids, and total phosphorus (100%). The probability that the total nitrogen concentration in the treated effluents would reach the limit value (30 mg/L) established for effluents discharged from a treatment plant of less than 2000 PE (population equivalent) to standing waters was 94%. The values of all the pollution indicators in wastewater discharged to the receiver were significantly lower than the limit values required in Poland. The investigated hybrid CW system with common reed, manna grass, and Virginia mallow guaranteed stable low values of BOD5, COD, total suspended solids, and total phosphorus in the treated wastewater, which meant it was highly likely to be positively evaluated in case of an inspection.

The paper presents the results of a study of the efficiency and technological reliability of total nitrogen and total phosphorus removal during long term operation of a one-stage constructed wetland system with subsurface horizontal wastewater flow. The flow rate of the wastewater treatment plant was 1.2 m3/d during the research period. Physical and chemical analyses of raw wastewater and treated effluent were carried out in the years 1997–2010 (14 years). During this study period, 56 series of analyses were performed and 112 wastewater samples were collected. It was observed that the average efficiency of total nitrogen and total phosphorus removal amounted to 51% and 73%, respectively. The technological reliability, determined by means of the Weibull reliability method, was 45% for total nitrogen removal and 48% in the case of total phosphorus removal. Total nitrogen and total phosphorus concentrations in the treated wastewater did not exceed the permissible values in 39.3% and 37.5% of cases, respectively. A negative correlation was found between the sorption capacity of the soil-plant filter for the removal of total phosphorus and the time of plant operation. The efficiency of total nitrogen removal was stable over time.

The quality of surface water in watercourses in the region of Lublin agglomeration was studied in 2012–2014. Biological and chemical indicators of the study for various sampling sites were detected and the resulting values of the indicators were processed statistically. Rivers characterized by small size and the flow and modification of the riverbed. The resulting low values of macrophyte river index and infusorial index pointed to a poor quality of surface waters. Chemical indicators of the quality of surface waters reached low values, only BOD and phosphates reached high values. The river is located outside the city and it is characterized by moderate potential ecological (III quality class), and the river within Lublin is insufficiently potential ecological (IV quality class). Statistical analysis showed high variability index values between the studied positions.

The purpose of this paper is to discuss the problem of changes of effectiveness of Kickuth-type constructed wetland with subsurface flow applied to domestic wastewater treatment. This study is based on an example of a wetland 3000 m

Poland is proud of 23 National Parks (NPs) which were established to protect unique European areas. Through cooperation between Life Science University in Lublin and the NPs, highly effective methods for environmental protection were introduced in Roztoczanski and Poleski National Parks. One method is a hybrid treatment wetland (HTW) for wastewater treatment. HTWs, if well designed and maintained, can effectively treat wastewater generated in houses and museum buildings in the area of the NPs. In 2014, three HTWs were constructed in Roztoczanski National Park (RNP) (A – Kosobudy, B – Zwierzyniec, C – Florianka). One of these installations was constructed in the shape of a fir tree (A – Kosobudy). In 2015 another one, in a turtle shape, was built in Poleski National Park (PNP) (D – Stare Zalucze). Similar wastewater treatment technology was applied in all facilities. The technology consisted of three steps: (i) mechanical treatment in three septic tank chambers, (ii) biological treatment in two or three stages of vertical and horizontal beds, and (iii) inactivation of phosphorus in p-filter with calcium-silica rock. Since the very beginning all facilities have been monitored and the results indicate very low concentrations of pollutants in the final effluents. It can be concluded that HTWs working according to the assumed technology fulfill the strict requirements for wastewater treatment in NP areas in Poland.