Search

Paper-based sensors and assays have evolved rapidly due to the conversion of paper-based microfluidics, functional paper coatings, and new electrical and optical readout techniques. Nanomaterials have gained substantial attraction as key components in paper-based sensors, as they can be coated or printed relatively easily on paper to locally control the device functionality. Here, we report a new combination of methods to fabricate carbon nanotube-based (CNT) electrodes for paper-based electrochemical sensors using a combination of laser cutting, drop-casting, and origami. We applied this process to a range of filter papers with different porosities and used their differences in three-dimensional cellulose networks to study the influence of the cellulose scaffold on the final CNT network and the resulting electrochemical detection of glucose. We found that an optimal porosity exists, which balances the benefits of surface enhancement and electrical connectivity within the cellulose scaffold of the paper-based device and demonstrates a cost-effective process for the fabrication of device arrays.

The development of low cost, portable, and disposable biosensors for equipment-free and naked-eye biosensing is in eager demand for their widespread application in biomedical field, but it is still a challenge. Herein, we propose a novel paper analytical device (PAD) for truly equipment-free and naked-eye biosensing using dopamine as the chromogenic agent based on target-initiated catalyzed oxidation reaction. The dopamine-functionalized PAD (DPAD) possesses a significant three-dimensional net structure, excellent hydrophilicity, and unique response toward G-quadruplex DNAs against other DNAs, benefiting the bio/chemo reaction occurrence to assay target biomolecules. In light of the exceptional properties, the fabricated DPAD was applied in the analysis of Dam MTase through target-triggered exponential isothermal amplification. The recognition and methylation of H1 by Dam MTase contribute to formation of abundant hemin/G-quadruplexes, which catalyze oxidation of dopamine into dopachrome and reduce the dopamine amount on the DPAD surface. In comparison with the case in which Dam MTase is absent, an evident deep pink signal originating from dopachrome is observed directly by the naked eye and relied on Dam MTase concentrations. Therefore, truly equipment-free and naked-eye detection of Dam MTase is achieved with a detection limit of 1.46 U/mL. The fabricated DPAD not only achieves Dam MTase-visualized detection but also permits the accurate determination of other analytes by varying recognizable DNA's sequences, thus offering a universal biosensor and depicting significant potential for widespread applications in biomedical field.

The deinking of mixed office waste paper by cellulase, M/Las (modification of laccase aspartic acid system), and C-M/Las (cellulase synergistic modification of laccase aspartic acid system) was investigated. The fiber morphology parameters, hydrogen bond patterns, cellulose crystallinity, and fiber microstructure were observed via fiber quality analyzer (FQA), Fourier transform infrared spectroscopy (FTIR), X-ray diffraction (XRD), and scanning electron microscopy (SEM). The results showed that the effective residual ink concentration of enzyme deinked pulp decreased compared with blank pulp (pulp without enzymatic treatment). The deinking efficiencies of C-M/Las, cellulase, and M/Las were 18.17%, 14.01%, and 12.31%, respectively. FQA analysis indicated that the fiber length and curl index decreased, while the fiber width slightly increased. FTIR analysis revealed that after cellulase, M/Las, and C-M/Las treatment, the content of intermolecular hydrogen bonds increased by 14.65%, 13.37%, and 19.80%, respectively. This indicates that there is a synergistic effect between cellulase and M/Las. XRD showed that the cellulose crystallinity decreased after enzymatic deinking. SEM micrographs of fibers treated with enzymes revealed that the fiber surface became rough and more fibrils appeared. The water retention value was increased after enzymatic deinking.

Contaminated water contains various types of pollutants, the removal of which requires two or more technologies. It is imperative but challenging to develop water purifier for simultaneous removal of multiple pollutants for the sake of easy operation, low cost, and etc. Previously reported multifunctional purifiers are normally nanoparticles which require caution during use. Here, we describe a design of paper-like multifunctional purifier, which has biomass-based structure by grafting polyethylenimine derived quaternary ammonium compounds onto three-dimensional bacterial cellulose substrate. Compared to similar materials reported previously, our product exhibited strikingly higher adsorption capacities towards various metal ions including Pb2+, Cu2+, and Cr6+, anionic organic dyes including congo red, methyl orange and methyl red, and excellent disinfection efficiency towards both Gram-negative and Gram-positive bacteria. Remarkably, this purifier also demonstrated effective removal of the three contaminative species simultaneously from both simulated and local polluted water. With more virtues of superior reusability and extreme handy convenience, we hope our molecular design could inspire further efforts on the rational construction of multifunctional water purifier with easy operation. We reckon our material to have strong potential for the possible use in water treatment, especially in regions that are short of environmental infrastructures.

Flexible pressure sensors have attracted considerable attention because of their potential applications in healthcare monitoring and human-machine interactions. However, the complicated fabrication process and the cos of sensing materials limit their widespread applications in practice. Herein, a flexible pressure sensor with outstanding performances is presented through an extremely simple and cost-efficient fabrication process. The sensing materials of the sensor are based on low-cost carbon black (CB)@airlaid paper (AP) composites, which are just prepared by drop-casting CB solutions onto APs. Through simply stacking multiple CB@APs with an irregular surface and a fiber-network structure, the obtained pressure sensor demonstrates an ultrahigh sensitivity of 51.23 kPa-1 and an ultralow detection limit of 1 Pa. Additionally, the sensor exhibits fast response time, wide working range, good stability, as well as excellent flexibility and biocompatibility. All the comprehensive and superior performances endow the sensor with abilities to precisely detect weak air flow, wrist pulse, phonation, and wrist bending in real time. In addition, an array electronic skin integrated with multiple CB@AP sensors has been designed to identify spatial pressure distribution and pressure magnitude. Through a biomimetic structure inspired by blooming flowers, a sensor with the open-petal structure has been designed to recognize the wind direction. Therefore, our study, which demonstrates a flexible pressure sensor with low cost, simple preparation, and superior performances, will open up for the exploration of cost-efficient pressure sensors in wearable devices.

In recent years, enzyme-linked immunosorbent assay (ELISA) plate fabricated on paper (P-ELISA) has been well developed. However, low sensitivity is its main disadvantage and has limited its use. In...

Green liquor dregs (GLD) are a major waste of the pulp and paper industry, and their correct classification is important to finding alternatives to landfill disposal. In the European Union, the met...

In this work, a triggerable H2O2-cleavable fluid switch mediated paper-based biochip, being amenable to multiplexing and quantitative analysis with the dual-response output of visual screening and ...

Cost-effective, simple and flexible hydrogen gas sensors operating at room temperature were demonstrated based on DC magnetron sputtered palladium thin films. The main idea is to use commercial microfiber filtration paper as a cheap, fibrous and flexible substrate for palladium. With this objective, Pd thin films with 21, 38 and 54 nm thicknesses were deposited and characterized by grazing incident X-ray diffraction (GIXRD) and scanning electron microscope (SEM). The gas sensing behavior was tested by hydrogen gas in the concentration rang of 0.5–10%. GIXRD showed a PdX/Pd phase and SEM revealed existing of many structural nanocracks. An activation process was needed where sensors were heated up to 110 °C in the presence of 10% H2. Then a desirable hydrogen sensitivity with good stability based on hydrogen induced lattice expansion (HILE) effect in which conductance increases was observed. However, for low Pd thicknesses (21 and 38 nm) and at below 4% H2, an inverse effect was observed in which the conductance decreased instead of increasing. For all samples the response time is incremental in the range of 0.5–4% and declining for 4–10%. Moreover, the deposited Pd sensors operate well when they are bent inward or outward. The governed physical mechanism was expressed and discussed.

Here we report the construction of CoFe2O4 coating on carbon fiber and the coated paper was used as the interlayer between the separator and cathode of Li-S batteries. The amorphous CoFe2O4 coating was deposited by the industry-oriented spray pyrolysis technique and carbon fiber was completely enwrapped by the coating. Compared to the non-coated carbon fiber, the coated carbon fiber as the interlayer exhibits a superior reversible capacity of 1086 mA h g−1 at moderate current of 0.1C and a low decay rate in the capacity of 0.043% per cycle after 1000 cycles at 1C. Excellent long-term cycling life and rate capacity were also achieved through the coated interlayer. The specially designed interlayer showed remarkable capability to trap effectively the intermediate LPS (lithium polysulfide). The significantly inhibited “shuttle effect” of LPS would give insight into designing and making the interlayer by using new coating materials for enhanced performances of the Li-S batteries.

A simple, low cost, and lightweight three-dimensional (3D) primary alkaline Zn/Fe3O4 origami-battery fabricated from Whatman 1 paper was developed. The battery was created using printed wax to define the hydrophobic and hydrophilic barriers and active electrocatalytic materials for fabricating the electrodes. The boat-shaped 3D-battery consisted of two screen-printed Zn/Fe3O4 batteries connected in series that were activated with a small volume of aqueous KOH solution. The metallic electrodes were first characterized outside the folded battery using electrochemical techniques. Subsequently, the electrodes and separator were assembled together in a triangle-shaped battery resembling the main structure of the boat-shaped 3D-device and this triangle-shaped battery was further optimized. The addition of water triggered the activation of the 3D battery delivering a maximum current and power of 7 mA and 3 mW, respectively. The 3D-Zn/Fe3O4-battery displayed an OCP of 2.2 V and a maximum current and power of 22 mA and 7.5 mW, respectively, in the presence of 6 M KOH electrolyte. These results demonstrate the potential of 3D origami-based structures and Zn/Fe3O4 batteries as an alternative low cost energy source to power portable devices.

The electrochemical oxidation of organics in paper mill wastewater belonging to Halfa industries (Tunisia) was performed by galvanostatic electrolyses using electro-Fenton (EF) process. The effect of several operating parameters, such as applied current density, electrodes material, air pressure and the presence of sodium chloride (NaCl) was evaluated. In particular, carbon felt (CF), modified carbon felt (MCF) and gas diffusion electrode (GDE) were used as cathode while Ti/IrO2-Ta2O5 and Boron Doped Diamond (BDD) as anode. Total Organic Carbon (TOC) measure was chosen as reference parameter to assess the extent of the treatment. The experimental results show that, by adopting the optimal set of operative conditions, EF can allow a high removal of TOC. It was shown that better performances can be achieved increasing the complexity of the treatment, by using sufficiently long electrolysis time or BDD as anode, MCF or GDE as cathode or the addition of NaCl.

Sphere shape nanocellulose with cellulose II type crystal structure was prepared from waste paper by the swelling on aqueous system NaOH/thiourea/urea, a efficient, inexpensive, and less toxic strategy. The crystalline structure of bleached pulp and nanocellulose was performed using XRD. The nanocellulose exhibits the cellulose II type crystal structure. The crystallinity index of the nanocellulose is calculated to be 48.85%, lower than those of bleached pulp (64.42%). The FTIR of the bleached pulp and the nanocellulose were collected. It indicated that lignin and hemicellulose were removed during the dissolution of cellulose. Sphere shape nanocellulose particles were observed by scanning electron microscopy and transmission electron microscopy. The particle size distribution of nanocellulose was determined using dynamic light scattering. It showed an average size of 50 nm. The thermal behaviors of the bleached pulp and nanocellulose were studied by thermo gravimetric. The obtained nanocellulose had better thermal stability than bleached pulp, which have potential applications in transistors and batteries with high thermal stability.

Focusing on eco-friendly materials, cellulose nanocrystal (CNC) extracted from office waste paper was used to reinforce waterborne polyurethane (WPU) with varying content by two incorporation routes including blending method by sonication after WPU synthesis (BCNC/WPU) and the alternative in-situ during the WPU synthesis process (CNC/WPU). The results showed that new interaction between CNC and WPU through hydrogen bonds in the interfacial area was formed and CNC reinforced hard segments effectively. However, the interaction in BCNC/WPU was not as stronger as that in CNC/WPU. Besides, CNC improved thermal stability of WPU remarkably, especially BCNC/WPU. The addition of CNC caused a delay around 50 °C in the start of the degradation process, and a delay of 5–18 °C and 2–20 °C in the temperatures at 10 and 50 wt% weight loss, respectively. These eco-friendly and biodegradable novel materials have potential applications in medical and biologic fields.

In this work, the effect of liquid evaporation on electrochemical measurements with electrochemical paper-based devices (ePADs) is studied. The time evolution of cyclic voltammograms of ferricyanide is used to study the effect of liquid evaporation under different conditions of relative humidity and air currents. Moreover, the enclosure of ePAD channels with adhesive tape is evaluated in terms of minimising the evaporation, as well as increasing the sensitivity in the electrochemical determination of horseradish peroxidase in long-term assays. This project has received funding from the European Union's Horizon 2020 research and innovation programme under grant agreement No 760876.

Refining (i.e., mechanical beating of pulp) is a common procedure that is used in paper-making to improve the mechanical properties of the final product. The improvements caused by refining are mainly attributed to increased density and to a better bonding between fibers. In this work, we study how various mechanisms that can be triggered by refining affect the tensile behavior of the sheets. Consequently, we use direct numerical simulations of fiber networks. We relate our finding to the experimental measurements that we conducted on handsheets. We have found that fibrillar fines with size distributions below the resolution of modern state-of-the art pulp characterization tools have a substantial contribution to the increased strength and stiffness of the sheets.

Waste paper is an environmentally friendly source of cellulosic material. Here we propose a new treatment based on nanocrystalline cellulose (CNC) for paper preservation and consolidation. Suspensions of CNC were prepared by sulfuric acid hydrolysis using waste paper as cellulose source (CNCWP) and compared with CNC from cotton linter (CNCCL). Both CNCs were obtained with good yield, showing high crystallinity index and comparable morphology, as demonstrated by DLS-ELS, XRD, FTIR, Raman and TEM analyses. CNCs were mixed with silver nanoparticles (CNC/Ag) and their biocidal activity was tested against Escherichia coli. and Bacillus subtilis, measuring the minimum inhibitory concentration. CNCs were exploited as treatments for biocidal activity and consolidation on Whatman paper. The presence of silver nanoparticles doesn't affect aesthetic appearance of the original paper and prevents the growth of Aspergillus niger fungus. Mechanical tests demonstrated that the coatings by CNC based products improve stretch and toughness of the paper support.

Filter paper (FP) with superhydrophobicity and high water adhesion was prepared by adsorption and simple immersion process. The surface morphologies displayed the micro-nano structure of FP. The surfaces composition was investigated by Fourier transform IR, X-ray photoelectron spectrum and X-ray diffractometer. The superhydrophobic surfaces with a water contact angle of 153° benefited from the Fe(OH)3 nanostructure formed on FP and subsequent stearic acid (STA) modification. The as-prepared superhydrophobic surfaces could firmly pin the water droplet even when the surfaces turned upside down. The wettability properties of the FP surfaces could be repaired by immersing the damaged samples into the solution again.

Mini-sabbaticals are formal short-term training and educational experiences away from an investigator’s home research unit. These may include rotations with other research units and externships at government research or regulatory agencies, industry and non-profit programs, and training and/or intensive educational programs. The National Institutes of Health have been encouraging training institutions to consider offering mini-sabbaticals, but given the newness of the concept, limited data are available to guide the implementation of mini-sabbatical programs. In this paper, we review the history of sabbaticals and mini-sabbaticals, report the results of surveys we performed to ascertain the use of mini-sabbaticals at Clinical and Translational Science Award hubs, and consider best practice recommendations for institutions seeking to establish formal mini-sabbatical programs.

Most high-voltage transformers are fluid filled machines whose insulation system is constituted of dielectric oil–solid combination. The insulation oil generally used is mineral oil, however, this fluid has started to be substituted by natural and synthetic esters due to their higher biodegradability and flash point in comparison with mineral oil. The introduction of a new fluid in the insulation system of power transformers requires kinetic models which can estimate the degradation rate of insulation solids, taking into account the properties of the new materials. The aim of this work is to go further in demonstrating that a kinetic model based on damage parameter can be used as a cellulose degradation model for Kraft paper, which is one of the solid materials used in the insulation system of oil-filled transformers. The ageing study has been extended to Kraft specimens immersed in two different oils (mineral and natural ester). The kinetic model that best tracks the ageing patterns was shown to be a function of damage parameter estimated through the energy consumed per unit volume of the failure zone (ER) in comparison with other mechanical properties such as rupture strength (σR) or strain under ultimate strength (ecm). Finally, an assessment of the effect of end-of-life criteria on correlation coefficient was carried out, providing further evidence that this criteria established until now (25% retained tensile strength) should be discussed in order to obtain more accurate kinetic models.

We propose a novel microfluidic paper-based phosphorus-detection chip (μPPC) for rapid analysis of trichlorfon, one of the most common organophosphate pesticide residues. The semi-quantification method was established and the limit of detection was 1.65 μg mL−1. We believe that the μPPCs could be a promising approach for the rapid determination of organophosphate pesticides.

With more and more applications, the mechanical strength of graphene paper (GP) has attracted significant attention in recent years. In this report, GPs were prepared by flow-induced filtration of electrochemical exfoliated graphene sheets. By adjusting the concentration of solution, we found graphene sheets fabricated in 0.1 M K2SO4 have the thinnest average thickness. And by uniaxial in-plane tensile tests operated on a self-developed in situ scanning electron microscopy (SEM) tensile stage, the corresponding GP has the best fracture strength of 192 MPa. This is due to that the thickness decrease of exfoliated graphene will increase the quantity of interlayer crosslinks, thus improving the mechanical properties of GPs. This research may open a new way to obtain high-strength GPs for applications.

We prepared a group-specific monoclonal antibody (Mab) that recognized the four macrolides, clarithromycin (CLA), erythromycin (ERY), roxithromycin (ROX) and azithromycin (AZI). The 50% inhibition concentration (IC50) values of CLA, ERY, ROX and AZI were 0.16, 0.52, 0.76, and 0.99 ng mL−1, respectively. Based on the Mab, a paper-based colorimetric assay was developed for rapid screening of CLA, ERY, ROX and AZI in milk samples. The assay displayed cutoff values of 2.5 ng mL−1, 5 ng mL−1, 5 ng mL−1, and 10 ng mL−1, respectively. For quantitative determination, the results were obtained using a strip scan reader, with limit of detection (LOD) values for CLA, ERY, ROX and AZI of 0.095, 0.085, 0.055 and 0.175 ng mL−1, respectively. These results suggest that the immunochromatographic assay is an ideal candidate for fast screening and quantitative analysis of CLA, ERY, ROX and AZI residues in milk.

The conversion of CO2 into useful chemicals can lead to the production of carbon neutral fuels and reduce greenhouse gas emissions. A key technological challenge necessary to enable such a process is the development of substrates that are active, cost effective, and selective for this reaction. In this regard, the reduction of CO2 via electrochemical means is one of the most attractive alternatives but still requires rather unique electrodes. Considering the potential of this approach, this report describes a one-step methodology for the synthesis of carbon electrodes derived from simple paper and modified with various metallic nanoparticles. Upon a preliminary selection based on the catalytic activity towards CO2 reduction, the electrodes containing CuNPs were further characterized by Raman spectroscopy, and electrical/electrochemical techniques. These electrodes were then applied for the electrochemical reduction of CO2, leading to the formation of compounds with one carbon atom (formic acid), two carbon atoms (ethenone), three carbon atoms (propanoic acid) and four carbon atoms (butanol and butanoic acid). Fil: Gomez, Federico Jose Vicente. Consejo Nacional de Investigaciones Científicas y Técnicas. Centro Científico Tecnológico Conicet - Mendoza. Instituto de Biología Agrícola de Mendoza. Universidad Nacional de Cuyo. Facultad de Ciencias Agrarias. Instituto de Biología Agrícola de Mendoza; Argentina Fil: Chumanov, George. Clemson University; Estados Unidos Fil: Silva, María Fernanda. Consejo Nacional de Investigaciones Científicas y Técnicas. Centro Científico Tecnológico Conicet - Mendoza. Instituto de Biología Agrícola de Mendoza. Universidad Nacional de Cuyo. Facultad de Ciencias Agrarias. Instituto de Biología Agrícola de Mendoza; Argentina. Clemson University; Estados Unidos Fil: Garcia, Carlos D.. Clemson University; Estados Unidos

A cellulose paper-based biosensor was developed for the equipment-free and naked-eye detection of a transcription factor (TF) using dopamine as the signal-responsive material based on exonuclease III-assisted cycling amplification. Compared with other TF biosensors, the proposed biosensor demonstrates low-cost, portable, disposable, and naked-eye detection features.

Foodborne pathogens are responsible for hundreds of thousands of deaths around the world each year. Rapid screening of agricultural products for these pathogens is essential to reduce and/or prevent outbreaks and pinpoint contamination sources. Unfortunately, current detection methods are laborious, expensive, time-consuming and require a central laboratory. Therefore, a rapid, sensitive, and field-deployable pathogen-detection assay is needed. We previously developed a colorimetric sandwich immunoassay utilizing immuno-magnetic separation (IMS) and chlorophenol red-β-D-galactopyranoside for Salmonella detection on a paper-based analytical device (μPAD); however, the assay required many sample preparation steps prior to the μPAD as well as laboratory equipment, which decreased user-friendliness for future end-users. As a step towards overcoming these limitations in resource-limited settings, we demonstrate a reusable 3D-printed rotational manifold that couples with disposable μPAD layers for semi-automated reagent delivery, washing, and detection in 65 minutes. After IMS to clean the sample, the manifold performs pipette-free reagent delivery and washing steps in a sequential order with controlled volumes, followed by enzymatic amplification and colorimetric detection using automated image processing to quantify color change. Salmonella was used as the target pathogen in this project and was detected with the manifold in growth media and milk with detection limits of 4.4 × 102 and 6.4 × 102 CFU mL−1 respectively. The manifold increases user friendliness and simplifies immunoassays resulting in a practical product for in-field use and commercialization.

A graphene oxide paper (GOP) was irradiated with 500 keV proton for total fluence of 2 × 1013 cm−2 to 2 × 1015 cm−2 in a ground-based irradiation simulator. The spacing of layer, surface chemical composition, structural defects, thermal conductivity and electrical property of the GOP before and after irradiation was measured. The results indicated that the spacing of layer decreased after irradiation. The ratio of total carbon atom and total oxygen atom increased from 2.40 to 4.31 as well as the sp2 hybridized carbons obviously increased after 2 × 1015 cm−2 irradiation. The XPS analysis suggested the occurrence of reduction, and the Raman spectra indicated that the defects were produced after proton irradiation. Furthermore, the thermal conductivity of GOP decreased, and then increased smoothly as the irradiation fluences were increased, and the electrical property showed the similar trend. The change in the thermal and electrical properties for GOP could be attributed to the defects and the removal of oxygen-containing functional groups, which lead to the phonon conduct path and scattering centers changed under proton irradiation. This study could promote the application of GOP in future space expeditions.

Supercapacitors are favored by researchers because of their high power density, especially with the acceleration of people's life rhythm. However, their energy density, especially from the point of view of the whole energy storage device, is far lower than that of commercial batteries. In this work, a kind of customizable full paper-based supercapacitor device with excellent self-healing ability is fabricated by simple and low-cost screen printing, electropolymerization and dip coating methods. The resultant separator-free supercapacitor device exhibits both ultrahigh gravimetric and areal specific energy (power) densities of 39 Wh kg−1 (69 kW kg−1) and 692 μWh cm−2 (236 mW cm−2), achieving excellent supercapacitor performance. Notably, the addition of vitrimers endows the whole device with outstanding self-healing properties, which is helpful for enhancing the adaptability of the device to the environment. In addition, this kind of paper-based device also displays good photothermal and electromagnetic shielding performances. These striking features make paper matrix composites attractive in the fields of supercapacitors, medical photothermal treatment and electromagnetic shielding.

Diesel Particulate filters are considered one of the most efficient technologies to reduce particulate matter emitted by diesel engines. In this paper we study the development of catalytic ceramic papers based on Mn-Ce and their applications as soot particle filters in bench scale tests. Ceramic papers were prepared by a dual polyelectrolyte papermaking method and were impregnated with Mn and Ce precursors through a wet-spray procedure using a commercial fogger. Catalytic ceramic papers were tested as catalysts for the combustion of soot, which was obtained both from the burning of diesel fuel and directly from a bench test. In addition, the filtering capacity of catalytic ceramic papers was tested through opacity measurements by placing the ceramic papers in a suitable case at the end of the engine. Mn-Ce based catalysts were active in the soot combustion. The addition of citric acid considerably improved the catalytic performance of all the systems studied. This beneficial effect of citric acid is related to an improvement in the distribution of the catalytic material onto the ceramic fibers, being the mixed equimolar oxide Mn-Ce the most active catalyst.

A simple process of commercial paper functionalisation via in situ polymerisation of conductive polymers onto cellulose fibres was investigated and applied as electrodes in paper-based batteries. The functionalisation involved polypyrrole (PPy) and Poly (3,4-ethylenedioxythiophene) (PEDOT) as conductive polymers with the process of functionalisation optimised for each polymer individually with respect to oxidant-to-monomer ratios and polymerisation times and temperature. Paper with conductivity values of 44 mS/cm was obtained by exposing the samples to pyrrole vapour for a period of 30 min at room temperature; however, polymerisation at temperatures of 40 °C lead to higher conductivity values to up 141 mS/cm. Consequently, functionalised PPy and PEDOT papers were applied as cathodes in batteries with Al foil anodes and commercial paper soaked in an electrolyte solution of NaCl.

This paper establishes a membraneless, co-laminar flow-based approach to develop a cost-effective microfluidic paper-based analytical device for enzymatic biofuel cell ( $\mu $ PAD-EBFC). The developed $\mu $ PAD-EBFC supporting the self-capillary fluid transport action consists of Y-shaped paper microchannel with the fuel (glucose) and oxidant (O2) streaming in parallel over carbon nanotube-based bucky paper electrodes modified with biocompatible electrocatalytic enzymes, such as glucose oxidase and laccase without any additional redox cofactor. The electrochemical performance for the modified bioelectrodes, i.e., electrocatalytic oxidation and reduction reaction, was carried out using linear sweep voltammetry, cyclic voltammetry, and open circuit potential. The overall performance of $\mu $ PAD-EBFC was evaluated using the polarization studies. Subsequently, the catalytic activity of enzymes on the electrode surface was validated by the scanning electron microscope. This simple and portable $\mu $ PAD-EBFC can generate the maximum power density to the order of $100~\mu \text{W}$ /cm2 ( $600~\mu \text{A}$ /cm2) at 0.505 V over prolonged durations of around 50 h. Hence, the presented $\mu $ PAD-EBFC shows good power density and stability, leading to its strong potential to power miniaturized microelectronics devices and sensors.

We report herein a facile and generalized approach to the modification of solid surfaces with polymer brushes under ambient conditions: filter paper‐assisted surface‐initiated Cu0‐mediated controlled radical polymerization (PSI‐CuCRP). The polymerization solution wetted filter paper is sandwiched between a copper plate and an initiator‐modified substrate, which allows the creation of a surface‐initiated polymerization (SIP) “band‐aid” so that everyone can perform the surface grafting selectively with good control over the quality of the polymer brushes employing low concentration and microliter amounts of the monomer solution. The versatility of this method is demonstrated by grafting different homo‐, block‐, and multicomponent polymer brushes by using the same activation system and reaction conditions, the polymerization process can be precisely controlled to yield uniform polymers and show high chain‐end functionality which is exemplified by in situ tetra‐copolymerization. The combination of photolithography and paper cutting enables to prepare arbitrary three‐dimensional patterned polymer brushes on the surface., A facile and generalized approach is reported for the modification of solid surfaces with polymer brushes under ambient conditions: filter paper‐assisted surface‐initiated Cu0‐mediated controlled radical polymerization. A surface‐initiated “band‐aid” of the monomer solution wetted filter paper covered with a thin copper plate allows to perform the surface grafting selectively with polymer brushes.

Graphical abstract, Highlights • Detection of cytokine storm biomarkers with mobile biosensors. • Immunosensors are made solely of cellulose modified with antibody-decorated nanoparticles. • Turnaround time under 10 min. • Detection of biomarkers in respiratory samples allows monitoring local inflammation. • Compatible with decentralized health care schemes., Decentralizing COVID-19 care reduces contagions and affords a better use of hospital resources. We introduce biosensors aimed at detecting severe cases of COVID-19 in decentralized healthcare settings. They consist of a paper immunosensor interfaced with a smartphone. The immunosensors have been designed to generate intense colorimetric signals when the sample contains ultralow concentrations of IL-6, which has been proposed as a prognosis biomarker of COVID-19. This is achieved by combining a paper-based signal amplification mechanism with polymer-filled reservoirs for dispensing antibody-decorated nanoparticles and a bespoken app for color quantification. With this design we achieved a low limit of detection (LOD) of 10−3 pg mL-1 and semi-quantitative measurements in a wide dynamic range between 10−3 and 102 pg mL-1 in PBS. The assay time is under 10 min. The low LOD allowed us to dilute blood samples and detect IL-6 with an LOD of 1.3 pg mL-1 and a dynamic range up to 102 pg mL-1. Following this protocol, we were able to stratify COVID-19 patients according to different blood levels of IL-6. We also report on the detection of IL-6 in respiratory samples (bronchial aspirate, BAS) from COVID-19 patients. The test could be easily adapted to detect other cytokines such as TNF-α and IL-8 by changing the antibodies decorating the nanoparticles accordingly. The ability of detecting cytokines in blood and respiratory samples paves the way for monitoring local inflammation in the lungs as well as systemic inflammation levels in the body.

The printability properties of the paper can be increased by some processes applied to the surface. The use of non-recyclable materials derived from petroleum is decreasing day by day, and the demand for recyclable materials obtained from renewable sources is increasing. These materials include cellulose derivatives, starch types and polyvinyl alcohol. The materials ratios, sizes, physical and chemical properties of these materials used in the processes applied to the paper and the content of the paper will affect the strength of the paper as well as change the surface properties and significantly affect the printability. The aim of this study is to obtain better printability properties by improving the paper surface with CNF/CNF-OX coating. In this study, fluting and core board papers coated with different amounts of cellulose nanofiber (CNF)/cellulose nanofiber-oxidized (CNF-OX) were produced. Surface properties, contact angle, surface energy, color and gloss of the produced papers were measured by optical microscope, goniometer, spectrophotometer and glossmeter. The papers were printed with the IGT C1 offset printability tester. As a result, in terms of printability, it was determined that CNF/CNF-OX coated papers have smoother surfaces and give better results in terms of both gloss properties and printability. [GRAPHICS] . WOS:000637661300003 2-s2.0-85103957996

In this study, a new solid phase extraction method based on the use of a low-cost funnel-shaped partially carbonized cellulose filter paper as a sorbent has been developed. The sorbent is easily prepared by heating the folded filter paper wetted with sulfuric acid solution and can be reused for several times. It is combined with dispersive liquid–liquid microextraction and used for the extraction of some pesticide residues from fruit juice samples prior to their analysis by gas chromatography–flame ionization detection. In this work, limits of detection and quantification were in the ranges of 0.30–0.61 and 1.0–2.0 µg L−1, respectively, and relative standard deviations ranged between 3 and 6% for intra– (n=5) and inter–day (n=5) precisions at a concentration of 25 µg L−1 of each pesticide. The enrichment factors of 452–751 were achieved. Extraction recoveries were in the range of 45–75%. The calibration curves had wide linear ranges with a good linearity (coefficient of determination ≥ 0.994). Finally, efficiency of the method was apprised by determining the analytes in fruit juice samples and relative recoveries were found to be in the range of 85–101%.

With the extensive use of palladium derivatives in the industry, their environmental pollution has become more and more serious. Herein, allyl functionalized hydrazone 2D COFs (XB-COFs) were found for selective fluorescent detection of Pd2+ (detection concentration of 0.29 μM) in water. The stable structure of the hydrazone bond and the complexation ability of allyl to Pd2+ cause XB-COF to have a good fluorescence sensing effect in both acid and alkaline solutions, and its adsorption capacity for Pd2+ is up to 120 mg g-1. During the interaction between XB-COF and Pd2+, a part of Pd2+ can be reduced to Pd nanoparticles with a diameter of about 10 nm. A fluorescent test paper was prepared by the in situ growth of XB-COF onto a filter paper, which can realize visualization detection of Pd2+ in 10 s with the naked eye or under a 365 nm UV lamp. This is the first time a fluorescent test paper based on in the situ growth of COFs has been applied for the detection of heavy metal ions, which provides a new platform for the application of COF materials in the medical health field, food safety, and environmental protection.

While current trends in Green Analytical Chemistry aim at reducing or simplifying sample treatment, food usually comprises complex matrices where direct analysis is not possible in most cases. In this context, sample treatment plays a pivotal role. Biogenic amines are naturally formed in many foodstuffs due to the action of microorganisms, while their presence has been associated with adverse health effects. In this work, the extraction of seven biogenic amines (cadaverine, histamine, phenylethylamine, putrescine, spermidine, spermine, and tyramine) from beer samples has been simplified using laboratory filter paper as sorbent without any further modification. The analysis of the eluates by direct infusion mass spectrometry reduces the time of analysis, increasing the sample throughput. This simple but effective method enabled the determination of the analytes with limits of detection as low as 0.06 mg•L−1 and relative standard deviations better than 11.9 %. The suitability of the method has been assessed by analyzing eight different types of beers by the standard addition method.

A simple and cheap filter paper-based SERS substrate has been developed for the sensing of tetracycline (TC) traces. In fact, antibiotics could represent a danger for environment and human health and TC is, in detail, one of the most wide-spread antibiotics entering the food chain and as water contaminant. According to this aim, Ag nanodisks (AgNDs) synthesis procedure was designed for tailoring the plasmonic peak position and, so, the SERS effect. Synthetized AgNDs were then used to simply decorate the surface of common filter paper, chosen because of its biocompatible, porosity and cheapness features. The obtained substrates based on filter paper and AgNDs allow the fast and easy analysis of aqueous solution containing first methylene blue used as standard and then TC samples. Fixed volume (20 μL) of TC solutions at different concentrations was simply dropped on the SERS support. The SERS spectrum was acquired before the complete water evaporation allowing TC detection down to the concentration of 10−9 M in aqueous solution. The results demonstrated that the SERS substrate obtained with the proposed facile, low-cost and relatively green fabrication process and the possibility to tune the plasmon excitation can be implemented for TC low concentration samples.

Paper has the potential to dramatically reduce the cost of electronic components. In fact, paper is 10 000 times cheaper than crystalline silicon, motivating the research to integrate electronic materials on paper substrates. Among the different electronic materials, van der Waals materials are attracting the interest of the scientific community working on paper-based electronics because of the combination of high electrical performance and mechanical flexibility. Up to now, different methods have been developed to pattern conducting, semiconducting and insulating van der Waals materials on paper but the integration of superconductors remains elusive. Here, the deposition of NbSe2, an illustrative van der Waals superconductor, on standard copy paper is demonstrated. The deposited NbSe2 films on paper display superconducting properties (e.g. observation of Meissner effect and resistance drop to zero-resistance state when cooled down below its critical temperature) similar to those of bulk NbSe2., Paper has the potential to dramatically reduce the cost of electronic components but the integration of electronic materials is challenging. Here the integration of NbSe2, a van der Waals superconductor, on paper is demonstrated.

Cellulosic nanomaterials are in the focus of academia and industry to realize light-weight biobased materials with remarkable strength. While the effect is well known, the distribution of these nanomaterials are less explored, particularly for paper sheets. Here, we explore the 3D distribution of micro and nanosized cellulosic particles in paper sheets and correlate their extent of fibrillation to the distribution inside the sheets and subsequently to paper properties. To overcome challenges with contrast between the particles and the matrix, we attached probes on the cellulose nano/microparticles, either by covalent attachment of fluorescent dyes or by physical deposition of cobalt ferrite nanoparticles. The increased contrast enabled visualization of the micro and nanosized particles inside the paper matrix using multiphoton microscopy, X-ray microtomography and SEM-EDX. The results indicate that fibrillary fines enrich at pores and fiber-fiber junctions, thereby increasing the relative bonded area between fibers to enhance paper strength while CNF seems to additionally form an inner 3D network.

Cellulose is a promising biomass material suitable for high volume applications. Its potential lies in sustainability, which is becoming one of the leading trends in industry. However, there are certain drawbacks of cellulose materials which limit their use, especially their high wettability and low barrier properties, which can be overcome by applying thin coatings. Plasma technologies present a high potential for deposition of thin environmentally friendly and recyclable coatings. In this paper, two different plasma reactors were used for coating two types of cellulose-based substrates with hexamethyldisiloxane (HMDSO). The changes in surface characteristics were measured by atomic force microscopy (AFM), scanning electron microscopy (SEM), surface free energy and contact angles measurements, X-ray photoelectron spectroscopy (XPS), and secondary ion mass spectrometry (SIMS). Successful oleofobization was observed for an industrial scale reactor where pure HMDSO was used in the absence of oxygen.

Negative ion mode paper spray mass spectrometry (PS-MS) suffers from intense background noise and unstable MS signal. For the first time, we reported fluorinated boron nitride nanosheet (h-FBN) assisted negative ion PS-MS for the detection of a series of molecules. We demonstrated that the introduction of h-FBN can greatly improve the detection sensitivity and signal stability in the negative ion mode.

Airflow sensor is a crucial component for monitoring environmental airflow conditions in many engineering fields, especially in the field of aerospace engineering. However, conventional airflow sensors have been suffering from issues such as complexity and bulk in structures, high cost in fabrication and maintenance, and low stability and durability. In this work, we developed a facile direct-writing method for fabricating a low-cost piezoresistive element aiming at high-performance airflow sensing, in which a commercial pen was utilized to drop solutions of single-walled carbon nanotubes onto tissue paper to form a piezoresistive sensing element. The encapsulated piezoresistive element was tested for electromechanical properties under two loading modes: one loading mode is the so-called pressure mode in which the piezoresistive element is pressed by a normal pressure, and another mode is the so-called bending mode in which the piezoresistive element is bended as a cantilever beam. Unlike many other developed airflow sensors among which the sensing elements are normally employed as cantilever beams for facing winds, we designed a fin structure to be incorporated with the piezoresistive element for airflow sensing, the main function of the fin is to face winds instead of the piezoresistive element, and subsequently transfer and enlarge the airflow pressure to the piezoresistive element for the normal pressure loading mode. With this design, the piezoresistive element can also be protected by avoiding experiencing large strains and direct contact with external airflows so that the stability and durability of the sensor can be maintained. Moreover, we experimentally found that the performance parameters of the airflow sensor could be effectively tuned by varying the size of the fin structure. When the fin sizes of the airflow sensors were 20 mm, 30 mm, and 40 mm, the detection limits and sensitivities of the fabricated airflow sensors were measured as 8.2 m/s, 6.2 m/s, 3.2 m/s, 0.0121 (m/s)−2, 0.01657 (m/s)−2, and 0.02264 (m/s)−2, respectively. Therefore, the design of the fin structure could pave an easy way for adjusting the sensor performance without changing the sensor itself toward different application scenarios.

International audience; The durability of paper documents treated with aminoalkylalkoxysilane copolymer (co-AAAS) flexible networks, as deacidifying and strengthenening agents, was studied. To this end, a 1922 lignocellulos ic newsprint paper was treated with co-AAASs and characterized. Physico-chemical properties such as pH, chromatism, opacity and mechanical strength were measured shortly upon treatment and several years after. In order to better understand the role of the initial degradation state of the paper and the impact of its constituents other than cellulose (lignin, alum-rosin sizing) on the treatment efficiency, several laboratory papers were added as models. It was shown that alum-rosin sizing contributed to a decrease in pH of the most degraded treated paper over the monitoring time, whereas the strengthening effect was mostly affected by the presence of lignin. In particular, for most papers, after several years, the gain in folding endurance was the lowest in the lignin-rich ones. The breaking length of all the papers increased post-treatment and over time, independently of the paper constituents. This was attributed to the slowly progressing aminoalkylalkoxysilanes polycondensation, on the scale of years, as evidenced by Cross Polarisation-Mass Angle Spinning 29 Si solid-state Nuclear Magnetic Resonance.

Made available in DSpace on 2020-12-12T02:09:36Z (GMT). No. of bitstreams: 0 Previous issue date: 2020-06-03 In this study, the direct analysis of doping agents in urine samples with no sample preparation by a modified paper spray mass spectrometry (PS-MS) methodology has been demonstrated for the first time. We have described a paper surface treatment with trichloromethylsilane using a gas-phase reaction to increase the ionization of target compounds. This approach was applied for the analysis of two classes of banned substances in urine samples: anabolic agents (trenbolone and clenbuterol) and diuretics (furosemide and hydrochlorothiazide). Under optimized conditions, the developed methods presented satisfactory repeatability, and an analysis of variance showed linearity without lack-of-fit. Highly sensitive detections as low as sub-nanogram per milliliter levels, which is below the minimum required performance levels proposed by the World Anti-Doping Agency, have been reached using the hydrophobic PS-MS analysis without any preconcentration and cleanup step. Department of Chemistry and Biochemistry Ohio State University, 100 West 18th Avenue Institute of Chemistry Department of Analytical Chemistry São Paulo State University (UNESP), Rua Professor Francisco Degni 55 ,P.O. Box 355 Institute of Chemistry Department of Analytical Chemistry São Paulo State University (UNESP), Rua Professor Francisco Degni 55 ,P.O. Box 355

Exploring efficient luminophores in the electrochemiluminescence (ECL) system is highly desired to pursue a sensitive ECL sensing platform. Herein, the black phosphorus nanosheets (BP NSs) with excellent ECL properties are investigated and serve as the luminophore with the coreactant of peroxydisulfate (S2O82-) solution. Moreover, owing to the overlapping of emission and absorbance spectra, effective resonance energy transfer (RET) is realized between the BP NSs and the introduced Au nanoparticles. In order to achieve the portable and miniaturized developing trends for the paper-based ECL sensing platform, a paper-based perovskite solar cell (PSC) device is designed to act as the power source to replace the commonly utilized expensive and cumbersome electrochemical workstation. Benefiting from that, a PSC driven paper-based constant potential ECL-RET sensing platform is constructed, thereby realizing sensitive microRNAs (miRNAs) detection. What's more, to attain the preferable analytical performance, the duplex-specific nuclease (DSN) is also introduced to assist the target recycling signal amplification strategy. Based on this, highly sensitive detection of miRNA-107 with a range from 0.1 pM to 15 nM is achieved by this designed sensing platform. Most importantly, this work not only pioneers a precedent for developing a high-sensitivity PSC triggered ECL sensing platform but also explores the application prospect of BP nanomaterial in the field of bioanalysis.

Materials for electronics that function as electrical and/or thermal conductors are often rigid, expensive, difficult to be sourced and sometimes toxic. An electrically and thermally conductive nanocomposite that is lightweight, flexible and eco-friendly could improve the environmental friendliness of the electronics sector and enable new applications. Considering this, we have fabricated electrically and thermally conductive flexible materials by functionalizing paper with nanocarbon conductive inks. Carnauba wax is emulsified in isopropyl alcohol and mixed with graphene nanoplatelets (GNPs) or with hybrids of GNPs and carbon nanofibers (CNFs). The percolation threshold of the hybrid samples is lowered compared with the pure GNPs composites, due to their increased filler aspect ratio. The hybrid samples also exhibit superior bending and folding stability. Densification of the coating to decrease their sheet resistance enables them to achieve as low as ~ 50 {\Omega} sq-1 for the GNP-based paper. The densification procedure improves the bending stability, the abrasion resistance, and the electromagnetic interference shielding of the paper-based conductors. Finally, the compressed samples show an impressive enhancement of their thermal diffusivity. The flexible and multifunctional nanocarbon coated paper is a promising electronic conductor and thermally dissipative material and, at the same time, can increase the environmental sustainability of the electronics sector., Comment: 27 pages, 4 figures

We describe a method for the differentiation of carboxylate anions on disposable paper supports (common printer paper, filter paper, chromatography paper), based on differential patterns of interactions between carboxylates and a fluorescent sensing system. The sensor was built from commercially available components, namely a polycationic fifth generation amine-terminated poly(amidoamine) dendrimer (PAMAM G5) and a small organic fluorophore (calcein) through non-covalent interactions. The assay's physical dimensions were chosen to conform to the microwell plate standard so detection could be carried out on widely available plate reader instrumentation. The sensing complex was first deposited in spots on a paper support to prepare the sensor strip; a carboxylate solution was then loaded on each spot. Nuanced changes in fluorescence were associated with carboxylate binding to the PAMAM dendrimer, characteristic of the structure and affinity of each carboxylate. Such signal changes, interpreted through Linear Discriminant Analysis (LDA), contained enough information to recognize and successfully discriminate most anions in the panel. Among the substrates we tested, chromatography paper was the most promising. The relationship between the structure of the carboxylates and the patterns giving rise to their differentiation was also discussed. Finally, the long-term stability ("shelf life") of the pre-assembled [calcein·dendrimer] sensing system was found to be excellent when deposited on paper support.

Different amounts of a stable aqueous TiO2 hydrosol were used to fabricate paper sheets having photocatalytic activity. The TiO2 hydrosol was prepared in aqueous medium using titanium butoxide as precursor and acetic acid as catalyst for the hydrolysis of titanium butoxide. An aging process at room temperature and atmospheric pressure was finally applied to obtain crystalline anatase TiO2 hydrosol. The effects of different TiO2 hydrosol loadings on the mechanical strength and barrier properties of modified paper sheets were investigated in detail. The photocatalytic behavior of TiO2-modified paper sheets was investigated as well using methylene blue (MB) as target pollutant.

The production of paper-based bacterial cellulose-chitosan (BC-Ch) nanocomposites was accomplished following two different approaches. In the first, BC paper sheets were produced and then immersed in an aqueous solution of chitosan (BC-ChI); in the second, BC pulp was impregnated with chitosan prior to the production of paper sheets (BC-ChM). BC-Ch nanocomposites were investigated in terms of physical characteristics, antimicrobial and antioxidant properties, and the ability to inhibit the formation of biofilms on their surface. The two types of BC-Ch nanocomposites maintained the hydrophobic character, the air barrier properties, and the high crystallinity of the BC paper. However, BC-ChI showed a surface with a denser fiber network and with smaller pores than those of BC-ChM. Only 5% of the chitosan leached from the BC-Ch nanocomposites after 96 h of incubation in an aqueous medium, indicating that it was well retained by the BC paper matrix. BC-Ch nanocomposites displayed antimicrobial activity, inhibiting growth of and having a killing effect against bacteria Staphylococcus aureus and Pseudomonas aeruginosa and yeast Candida albicans. Moreover, BC-Ch papers showed activity against the formation of a biofilm on their surface. The incorporation of chitosan increased the antioxidant activity of the BC paper. Paper-based BC-Ch nanocomposites combined the physical properties of BC paper and the antimicrobial, antibiofilm, and antioxidant activities of chitosan.