Search

The bondline of electric-resistance-welded (ERW) linepipe steel, often etched white (i.e., ferrite) in optical microscopy, is generally believed to be carbon depleted. The mechanism for the carbon depletion, however, is not fully understood by researchers. To this end, atom probe tomography (APT) was used to measure elemental segregation of the as-welded and post-weld heat-treated bondline regions of X70 linepipe welds. The thin vertical features at the bondline in the as-welded condition were identified as carbon-rich martensite-austenite (M-A) constituents, and the majority ferrite phase in the bondline was identified as carbon-depleted ferrite. Following the post-weld normalization, all alloying elements, except Nb and Mo, are homogenized across the bondline and heat-affected zone. The carbon depletion in the ERW bondline was accurately measured. A new mechanism for carbon depletion has been proposed using Scheil calculations of elemental partitioning during weld formation. Segregation of elements in the heat-affected zone was shown to follow the negligible partitioning local equilibrium (NPLE) kinetics for bainite transformation.

MXenes, a new family of functional two-dimensional (2D) materials, have shown great potential for an extensive variety of applications within the last decade. Atomic defects and functional groups in MXenes are known to have a tremendous influence on the functional properties. In this review, we focus on recent progress in the characterization of atomic defects and functional group chemistry in MXenes, and how to control them to directly influence various properties (e.g., electron transport, Li' adsorption, hydrogen evolution reaction (HER) activity, and magnetism) of 2D MXenes materials. Dynamic structural transformations such as oxidation and growth induced by atomic defects in MXenes are also discussed. The review thus provides perspectives on property optimization through atomic defect engineering, and bottom-up synthesis methods based on defect-assisted homoepitaxial growth of MXenes. (C) 2020 Chinese Chemical Society and Institute of Materia Medica, Chinese Academy of Medical Sciences. Published by Elsevier B.V. All rights reserved.

Atmospheric pressure chemical vapor deposition (APCVD) has been used extensively for synthesizing two-dimensional (2D) materials, due to its low cost and promise for high-quality monolayer crystal synthesis. However, the understanding of the reaction mechanism and the key parameters affecting the APCVD processes is still in its embryonic stage. Hence, the scalability of the APCVD method in achieving large scale continuous film remains very poor. Here, we use MoSe2 as a model system and present a fluid guided growth strategy for understanding and controlling the growth of 2D materials. Through the integration of experiment and computational fluid dynamics (CFD) analysis in the full-reactor scale, we identified three key parameters: precursor mixing, fluid velocity and shear stress, which play a critical role in the APCVD process. By modifying the geometry of the growth setup, to enhance precursor mixing and decrease nearby velocity shear rate and adjusting flow direction, we have successfully obtained inch-scale monolayer MoSe2. This unprecedented success of achieving scalable 2D materials through fluidic design lays the foundation for designing new CVD systems to achieve the scalable synthesis of nanomaterials.

The localized corrosion of Li-containing nm hardening precipitates in the 3rd generation of Al-Cu-Li alloys was investigated based on a quasi in situ approach by sequentially exposing the material to NaCl solution and characterizing the structural, chemical, and electrochemical evolution at atomic scale using electron microscopy, spectroscopy, 3D tomography, electrochemical measurements, and DFT calculations. Localized corrosion of Al7.5Cu4Li (TB phase) initiated along {001} family of planes through the dealloying of Al and Li due to a low surface work function. Cu was enriched along the Cu (110) // TB (011) // Al (100) orientations on and around corroded TB precipitates. No strong galvanic interactions were observed at the TB and Al matrix interface due to the formation of a Li-C-O rich passivation layer during electrolyte exposure. Similarities and differences between TB and other common Al-Cu-Li precipitates (Al2CuLi, Al6CuLi3, and Al3Li) with respect to corrosion are discussed. The reported corrosion mechanism can assist in the assessment of the localized corrosion susceptibility of precipitation-hardened Al alloys and assist in the design of new alloys.

Strain engineering enables the direct modification of atomic bonding and is currently an active area of research aimed at improving electrocatalytic activity. However, directly measuring the lattic...

Recent advances in design and processing technology have made possible commercialization of polycrystalline (px)-CdTe as a photovoltaic absorber. Grain boundaries (GBs) are the most prominent struc...

Assembling matter atom-by-atom into functional devices is the ultimate goal of nanotechnology. The possibility of achieving this goal is intrinsically dependent on the ability to visualize matter at the atomic level, induce and control atomic-scale motion, facilitate and direct chemical reactions, and coordinate and guide fabrication processes towards desired structures atom-by-atom. In this Perspective, we summarize recent progress in chemical transformations, material alterations and atomic dynamics studies enabled by the converged, atomic-sized electron beam of an aberration-corrected scanning transmission electron microscope. We discuss how such top-down observations have led to the concept of controllable, beam-induced processes and then of bottom-up, atom-by-atom assembly via electron-beam control. The progress in this field, from electron-beam-induced material transformations to atomically precise doping and multi-atom assembly, is reviewed, as are the associated engineering, theoretical and big-data challenges. Electron beams in a transmission electron microscope can be used to manipulate matter atom-by-atom. This Review surveys the recent advances and discusses how the further development and integration of machine learning, theory, feedback and instrumentation will push the field forward.

The failure to achieve stable Ohmic contacts in two-dimensional material devices currently limits their promised performance and integration. Here we demonstrate that a phase transformation in a re...

Currently, most two-dimensional (2D) materials that are of interest to emergent applications have focused on van der Waals–layered materials (VLMs) because of the ease with which the layers can be separated (e.g., graphene). Strong interlayer-bonding-layered materials (SLMs) in general have not been thoroughly explored, and one of the most critical present issues is the huge challenge of their preparation, although their physicochemical property transformation should be richer than VLMs and deserves greater attention. MAX phases are a classical kind of SLM. However, limited to the strong interlayer bonding, their corresponding 2D counterparts have never been obtained, nor has there been investigation of their fundamental properties in the 2D limitation. Here, the authors develop a controllable bottom-up synthesis strategy for obtaining 2D SLMs single crystal through the design of a molecular scaffold with Mo 2GaC, which is a typical kind of MAX phase, as an example. The superconducting transitions of Mo 2GaC at the 2D limit are clearly inherited from the bulk, which is consistent with Berezinskii–Kosterlitz–Thouless behavior. The authors believe that their molecular scaffold strategy will allow the fabrication of other high-quality 2D SLMs single crystals, which will further expand the family of 2D materials and promote their future application.

${\mathrm{PdCoO}}_{2}$, belonging to a family of triangular oxides called delafossite, is one of the most conducting oxides. Its in-plane conductivity is comparable to those of the best metals and exhibits hydrodynamic electronic transport with an extremely long mean free path at cryogenic temperatures. Nonetheless, it is nonmagnetic despite the presence of the cobalt ion. Here, we show that a mild hydrogenation process reduces ${\mathrm{PdCoO}}_{2}$ thin films to an atomically mixed alloy of PdCo with strong out-of-plane ferromagnetism and sign-tunable anomalous Hall effect. Considering that many other compounds remain little affected under a similar hydrogenation condition, this discovery may provide a route to creating novel spintronic heterostructures combining strong ferromagnetism, involving oxides and other functional materials.

Pulsed laser deposition (PLD) can be considered a powerful method for the growth of two-dimensional (2D) transition-metal dichalcogenides (TMDs) into van der Waals heterostructures. However, despite significant progress, the defects in 2D TMDs grown by PLD remain largely unknown and yet to be explored. Here, we combine atomic resolution images and first-principles calculations to reveal the atomic structure of defects, grains, and grain boundaries in mono- and bilayer MoS2 grown by PLD. We find that sulfur vacancies and MoS antisites are the predominant point defects in 2D MoS2. We predict that the aforementioned point defects are thermodynamically favorable under a Mo-rich/S-poor environment. The MoS2 monolayers are polycrystalline and feature nanometer size grains connected by a high density of grain boundaries. In particular, the coalescence of nanometer grains results in the formation of 180° mirror twin boundaries consisting of distinct 4- and 8-membered rings. We show that PLD synthesis of bilayer MoS2 results in various structural symmetries, including AA' and AB, but also turbostratic with characteristic moiré patterns. Moreover, we report on the experimental demonstration of an electron beam-driven transition between the AB and AA' stacking orientations in bilayer MoS2. These results provide a detailed insight into the atomic structure of monolayer MoS2 and the role of the grain boundaries on the growth of bilayer MoS2, which has importance for future applications in optoelectronics.

High-entropy oxides (HEOs) have attracted great interest in diverse fields because of their inherent opportunities to tailor and combine materials functionalities. The control of local order/disorder in the class is by extension a grand challenge toward realizing their vast potential. Here we report the first examples of pyrochlore HEOs with five M-site cations, for Nd2M2O7, in which the local structure has been investigated by neutron diffraction and pair distribution function (PDF) analysis. The average structure of the pyrochlores is found to be orthorhombic Imma, in agreement with radius-ratio rules governing the structural archetype. The computed PDFs from density functional theory relaxed special quasirandom structure models are compared with real space PDFs in this work to evaluate M-site order/disorder. Reverse Monte Carlo combined with ab initio molecular dynamics and Metropolis Monte Carlo simulations demonstrates that Nd2(Ta0.2Sc0.2Sn0.2Hf0.2Zr0.2)2O7 is synthesized with its M-site local to nanoscale order highly randomized/disordered, while Nd2(Ti0.2Nb0.2Sn0.2Hf0.2Zr0.2)2O7+x exhibits a strong distortion of the TiO6 octahedron and small degree of Ti chemical short-range order (SRO) on the subnanometer scale. Calculations suggest that this may be intrinsic, energetically favored SRO rather than due to sample processing. These results offer an important demonstration that the engineered variation of participating ions in HEOs, even among those with very similar radii, provides richly diverse opportunities to control local order/disorder motifs-and therefore materials properties for future designs. This work also hints at the exquisite level of detail that may be needed in computational and experimental data analysis to guide structure-property tuning in the emerging HEO materials class.

Insights into the dynamics of electrochemical processes are critically needed to improve our fundamental understanding of electron, charge, and mass transfer mechanisms and reaction kinetics that influence a broad range of applications, from the functionality of electrical energy-storage and conversion devices (e.g., batteries, fuel cells, and supercapacitors), to materials degradation issues (e.g., corrosion and oxidation), and materials synthesis (e.g., electrodeposition). To unravel these processes, in situ electrochemical scanning/transmission electron microscopy (ec-S/TEM) was developed to permit detailed site-specific characterization of evolving electrochemical processes that occur at electrode–electrolyte interfaces in their native electrolyte environment, in real time and at high-spatial resolution. This approach utilizes “closed-form” microfabricated electrochemical cells that couple the capability for quantitative electrochemical measurements with high spatial and temporal resolution imaging, spectroscopy, and diffraction. In this article, we review the state-of-the-art instrumentation for in situ ec-S/TEM and how this approach has resulted in new observations of electrochemical processes.

Thermal protection systems (TPS) are used to protect spacecraft payloads during the extreme conditions of atmospheric entry. The backbone of the composite TPS material used in the NASA Stardust Sample Return Capsule and the Mars 2020 mission is carbon fiber, which oxidizes at these temperatures and atmospheric conditions. This study presents the direct observation of carbon oxidation using in situ Scanning Transmission Electron Microscopy (STEM). A thin section of a commercially-available carbon fiber material containing multiple carbon structures was examined by STEM in a closed-environmental cell in which temperature was raised from 25 to 1050àC under a steady flow of air. Results show that the random polycrystalline carbon structure oxidized more uniformly and rapidly than the single crystallite region, which oxidized more anisotropically. These findings are the first to directly observe the structural dependence of carbon oxidation rates at these length-scales while also giving important insight into the onset of pitting at various active surface sites, important pieces in fundamentally understanding of carbon oxidation.

High-capacity alloy anode materials for Li-ion batteries have long been held back by limited cyclability caused by the large volume changes during lithium insertion and removal. Hollow and yolk-shell nanostructures have been used to increase the cycling stability by providing an inner void space to accommodate volume changes and a mechanically and dimensionally stable outer surface. These materials, however, require complex synthesis procedures. Here, using in situ transmission electron microscopy, we show that sufficiently small antimony nanocrystals spontaneously form uniform voids on the removal of lithium, which are then reversibly filled and vacated during cycling. This behaviour is found to arise from a resilient native oxide layer that allows for an initial expansion during lithiation but mechanically prevents shrinkage as antimony forms voids during delithiation. We developed a chemomechanical model that explains these observations, and we demonstrate that this behaviour is size dependent. Thus, antimony naturally evolves to form optimal nanostructures for alloy anodes, as we show through electrochemical experiments in a half-cell configuration in which 15-nm antimony nanocrystals have a consistently higher Coulombic efficiency than larger nanoparticles. Sufficiently small antimony nanoparticles form uniform voids that are reversibly filled and vacated during cycling.

Bimetallic nanocrystals with a core@shell architecture are versatile, multifunctional particles. The lattice mismatch between core and shell regions induces strain, affecting the electronic properties of the shell metal, which is important for applications in catalysis. Here, we analyze this strain in core@shell nanocubes as a function of lattice mismatch and shell thickness. Coupling geometric phase analysis from atomic resolution scanning transmission electron microscopy images with molecular dynamics simulations reveals lattice relaxation in the shell within only a few monolayers and an overexpansion in the axial direction. Interestingly, many works report core@shell metal nanocatalysts with optimum performance at greater shell thicknesses. Our findings suggest that not strain alone but secondary factors, such as structural defects or structural changes in operando, may account for observed enhancements in some strain-engineered nanocatalysts; e.g., Rh@Pt nanocubes for formic acid electrooxidation.

The ability to predict and understand phases in high-entropy alloys (HEAs) is still being debated, and primarily true predictive capabilities derive from the known thermodynamics of materials. The present work demonstrates that prior work using high-throughput first-principles calculations may be further utilized to provide direct insight into the temperature- and composition-dependent phase evolution in HEAs, particularly Al-containing HEAs with a strengthening multiphase microstructure. Using a simple model with parameters derived from first-principles calculations, we reproduce the major features associated with Al-containing phases, demonstrating a generalizable approach for exploring potential phase evolution where little experimental data exists. Neutron scattering, in situ microscopy, and calorimetry measurements suggest that our high-throughput Monte Carlo technique captures both qualitative and quantitative features for both intermetallic phase formation and microstructure evolution at lower temperatures. This study provides a simple approach to guide HEA development, including ordered multi-phase HEAs, which may prove valuable for structural applications., Exploration of high entropy alloy phases where little experimental data exists is still challenging. Here, the authors develop an approach where parameters from first principle simulations are incorporated into Monte Carlo simulations to reproduce phase evolution of aluminium-containing high entropy alloys.

Summary Conversion and alloying electrode materials offer high specific capacity for emerging sodium- and potassium-ion batteries, but the larger volume changes compared to reaction with lithium are thought to limit cyclability. The reaction mechanisms of many materials with Na+ and K+ are unknown, however, and this knowledge is key for engineering mechanically resilient materials. Here, in situ transmission electron microscopy is used to uncover the nanoscale transformations during the reaction of FeS2 electrode materials with Li+, Na+, and K+. Surprisingly, despite larger volume changes during the conversion reaction with Na+ and K+, the FeS2 crystals only fracture during lithiation. Modeling of reaction-induced deformation shows that the shape of the two-phase reaction front influences stress evolution, and unique behavior during lithiation causes stress concentrations and fracture. The larger volume changes in Na- and K-ion battery materials may therefore be managed through understanding and control of reaction mechanisms, ultimately leading to better alkali-ion batteries.

A Pd-promoted Re/SiO2 catalyst was prepared by sequential impregnation and compared to monometallic Pd/SiO2 and Re/SiO2. All samples were characterized by electron microscopy, H2 and CO chemisorption, H2 temperature-programmed reduction, and in-situ X-ray absorption spectroscopy at the Re LIII and Pd K-edges. The samples were also tested in the reduction of propionic acid to 1-propanol and propionaldehyde at 433 K in 0.1-0.2 MPa H2. Whereas monometallic Pd was inactive for carboxylic acid reduction, monometallic Re catalyzed aldehyde formation, but only after high-temperature pre-reduction that produced metallic Re. When Pd was present with Re in a bimetallic catalyst, Pd facilitated the reduction of Re in H2 to ~4+ oxidation state at modest temperatures, producing an active catalyst for the conversion of propionic acid to 1-propanol. Under the conditions of this study, the orders of reaction in propionic acid and H2 were approximately zero and one, respectively. Transient kinetic analysis of the carboxyl...

Optimizing proton conduction in solids remains the most promising solution for achieving intermediate temperature (∼750–1000 K) solid oxide fuel cell devices, and enabling selective membranes for H2 separation. Proton conduction, a thermally activated process, exhibits its highest rates in yttrium (Y) acceptor doped BaZrO3 at an optimal doping level of 20% Y. The presence of extended defects such as grain boundaries has typically generated a wide variability in reported conductivity values. This has hindered a fundamental mechanistic understanding of how (acceptor) doping levels correlate with the activation energy of protons to produce an optimal doping level for fast proton transport. While isolated dopants have been suggested as the primary source of proton trapping, our results indicate that it is the local dopant-density that matters. Here, we show that increasing the local dopant density promotes localized lattice distortions in the presence of point defects such as oxygen-vacancies or proton inters...

Graphene, with unique mechanical and electrical properties, offers diverse application opportunities from beyond Moore’s nano-electronics to water filtration. However, accomplishing these relies on cleaning and processing large areas of supported and suspended graphene sheets. Here, we demonstrate the use of an Ar cluster ion beam as a versatile tool for graphene cleaning, defect engineering, and nanopore fabrication. In-situ and ex-situ characterization techniques were utilized in combination with first principles molecular dynamics, to highlight the differences in processing of the supported and suspended graphene samples. In this work, we monitor interaction of the Ar cluster ion beam with graphene as a function of ion dose with in-situ secondary ion mass spectrometry (SIMS), as well as ex-situ Raman spectroscopy measurements. Scanning transmission electron microscopy (STEM) results confirm that the Ar cluster ion beam can form nanopores in the suspended graphene; while the basal plane of graphene remains intact maintaining the lattice structure. Finally, Scanning Electron Microscopy (SEM) image analysis of the irradiated samples allows quantitative tracking of pore areas and their distribution as a function of ion dose. This study highlights the flexibility of the Ar cluster ion beam in 2D material processing, and offers insights into Ar beam interaction with graphene.

Atomically dispersed Co(II) cations coordinated to nitrogen in a carbon matrix (Co-N-C) catalyze oxidative dehydrogenation of benzyl alcohol in water with a specific activity approaching that of supported Pt nanoparticles. Whereas Cu(II) cations in N-doped carbon also catalyze the reaction, they are about an order of magnitude less active compared with Co(II) cations. Results from X-ray absorption spectroscopy suggest that oxygen is also bound to N-coordinated Co(II) sites but that it can be partially removed by H2 treatments at 523–750 K. The N-coordinated Co(II) sites remained cationic in H2 up to 750 K, and these stable sites were demonstrated to be active for propane dehydrogenation. In situ characterization of Cu(II) in N-doped carbon revealed that reduction of the metal in H2 started at about 473 K, indicating a much lower thermal stability of Cu(II) in H2 relative to Co(II). The demonstrated high catalytic activity and thermal stability of Co-N-C in reducing environments suggests that this material...

The synthesis of monodisperse size- and shape-controlled Au nanocrystals is often achieved with cetyltrimethylammonium bromide (CTAB) surfactant; however, its role in the growth of such tailored nanostructures is not well understood. To elucidate the formation mechanism(s) and evolution of the morphology of Au nanocrystals in the early growth stage, we present an in situ liquid-cell scanning transmission electron microscopy (STEM) investigation using electron beam-induced radiolytic species as the reductant. The resulting particle shape at a low beam dose rate is shown to be strongly influenced by the surfactant; the Au nanocrystal growth rate is suppressed by increasing the CTAB concentration. At a low CTAB concentration, the nanoparticles (NPs) follow a reaction-limited growth mechanism, while at high a CTAB concentration the NPs follow a diffusion-limited mechanism, as described by the Lifshitz–Slyozov–Wagner (LSW) model. Moreover, we investigate the temporal evolution of specific NP geometries. The am...

Lanthanide (Ln) group elements have been attracting considerable attention owing to the distinct optical properties. The crystal-field surroundings of Ln ions in the host materials can determine their energy level splitting, which is of vital importance to tailor their optical properties. 2D MoS2 single crystals were utilized as the host material to embed Eu3+ and energy-level splitting was achieved for tuning its photoluminescence (PL). The high anisotropy of the 2D host materials makes them distort the degenerate orbitals of the Ln ions more efficiently than the symmetrical bulk host materials. A significant red-shift of the PL peak for Eu3+ was observed. The strategy for tailoring the energy level splitting of Ln ions by the highly designable 2D material crystal field provides a new method to extend their optical properties.

Understanding of structural, electrical, and gravimetric peculiarities of water vapor interaction with ion-intercalated MXenes led to design of a multimodal humidity sensor. Neutron scattering coupled to molecular dynamics and ab initio calculations showed that a small amount of hydration results in a significant increase in the spacing between MXene layers in the presence of K and Mg intercalants between the layers. Films of K- and Mg-intercalated MXenes exhibited relative humidity (RH) detection thresholds of ∼0.8% RH and showed monotonic RH response in the 0-85% RH range. We found that MXene gravimetric response to water is 10 times faster than their electrical response, suggesting that H2O-induced swelling/contraction of channels between MXene sheets results in trapping of H2O molecules that act as charge-depleting dopants. The results demonstrate the use of MXenes as humidity sensors and infer potential impact of water on structural and electrical performance of MXene-based devices.

The performance characteristics of lithium-ion battery cathode materials are governed by the surface structure and chemistry. Synthesis is known to affect the structure of these materials; however, a full understanding of the effects of the surface structure is not well understood. Here, we explore the atomic scale structure of lithium-layered oxides prepared with two different thermal treatments. We show that, under certain thermal treatments, the surface perpendicular to the transition-metal layers is enriched in nickel, which results in Ni occupying the lithium layer of the layered oxide structure. Under both thermal treatments, this surface also shows a reduction of Mn, with some of the reduced Mn occupying sites in the lithium layer. The surface parallel to the transition-metal layers under both treatments shows significant Mn reduction, oxygen loss, and reduced Mn in the lithium layer. The Mn reduction and surface reconstruction are the result of unstable surface terminations and are intrinsic to la...

Surface strains can enhance the performance of platinum-based core@shell electrocatalysts for the oxygen reduction reaction (ORR). Bimetallic core@shell nanoparticles (NPs) are widely studied nanocatalysts but often have limited lattice mismatch and surface compositions; investigations of core@shell NPs with greater compositional complexity and lattice misfit are in their infancy. Here, a new class of multimetallic NPs composed of intermetallic cores and random alloy shells is reported. Specifically, face-centered cubic Pt-Cu random alloy shells were deposited on PdCu B2 intermetallic seeds in a facet-dependent manner, giving rise to faceted core@shell NPs with highly strained surfaces. High-resolution transmission electron microscopy revealed orientation-dependent surface strains, where the compressive strains were greater on Pt-Cu {200} than {111} facets. These core@shell NPs provide higher specific area and mass activities for the ORR when compared to conventional Pt-Cu NPs. Moreover, these intermetallic@random alloy NPs displayed high endurance, undergoing 10,000 cycles with only a slight decay in activity and no apparent structural changes.

The strength of metal–support bonding in heterogeneous catalysts determines their thermal stability, therefore, a tremendous amount of effort has been expended to understand metal–support interactions. Herein, we report the discovery of an anomalous “strong metal–support bonding” between gold nanoparticles and “nano-engineered” Fe3O4 substrates by in situ microscopy. During in situ vacuum annealing of Au–Fe3O4 dumbbell-like nanoparticles, synthesized by the epitaxial growth of nano-Fe3O4 on Au nanoparticles, the gold nanoparticles transform into the gold thin films and wet the surface of nano-Fe3O4, as the surface reduction of nano-Fe3O4 proceeds. This phenomenon results from a unique coupling of the size-and shape-dependent high surface reducibility of nano-Fe3O4 and the extremely strong adhesion between Au and the reduced Fe3O4. This strong metal–support bonding reveals the significance of controlling the metal oxide support size and morphology for optimizing metal–support bonding and ultimately for the...

The effect of support on electrocatalytic activity of Cu nanoparticles (NPs) towards CO2 electroreduction to hydrocarbon fuels (CH4 and C2H4) is investigated for three types of nanostructured carbons: single wall carbon nanotubes (SWNT), reduced graphene oxide (RGO) and onion-like carbon (OLC). Cu/SWNT, Cu/RGO and Cu/OLC composite catalysts are synthesized and characterized by X-ray diffraction analysis, transmission electron microscopy and electrochemical surface area measurements. Electrocatalytic activities of the synthesized materials, as measured in an electrochemical cell connected to a gas chromatograph, are compared to that of Cu NPs supported on Vulcan carbon. All four catalysts demonstrate higher activity towards C2H4 generation vs CH4, with production of the latter mostly suppressed on Cu NPs supported on nanostructured substrates. Onset potentials for C2H4 vs CH4 generation demonstrate 200 mV positive shifts for Cu/SWNT, Cu/RGO, and Cu/OLC catalysts. The Cu/OLC catalyst is found to be superior to the other two nanostructured catalysts in terms of stability, activity and selectivity towards C2H4 generation. Its faradaic efficiency reached 60% at −1.8 V vs Ag/AgCl. The enhanced stability and activity of the Cu/OLC catalyst can be attributed to the unique catalyst design, wherein a shell of OLC surrounds the Cu NPs. Such a configuration enables the outer layer to act as a filter that protects the Cu surface from adsorption of undesirable species, enhances its electrocatalytic performance, and improves its viability in CO2 electroreduction reaction. The enhanced selectivity of the Cu/OLC catalyst towards the C2H4 production is most likely related to the enhanced electrocatalytic activity of the OLC support towards the CO2 electroreduction to CO. Higher CO surface concentration from CO2 electroreduction on the OLC support, rather than a greater number of available sites for CO dimerization, likely originated this behavior. CO molecules generate on surfaces of OLCs, dimerize on Cu NP (100) planes, and, subsequently, yield additional C2H4 molecules. Both the reduction of the CO2 to CO on the surface of OLCs and reduction of “extra” CO molecules to C2H4 on the surface of Cu NPs are expected to lead to an increase in the local pH, which is also beneficial for the C2H4 production.

The ability to engineer the thermal conductivity of materials allows us to control the flow of heat and derive novel functionalities such as thermal rectification, thermal switching and thermal cloaking. While this could be achieved by making use of composites and metamaterials at bulk length-scales, engineering the thermal conductivity at micro- and nano-scale dimensions is considerably more challenging. In this work, we show that the local thermal conductivity along a single Si nanowire can be tuned to a desired value (between crystalline and amorphous limits) with high spatial resolution through selective helium ion irradiation with a well-controlled dose. The underlying mechanism is understood through molecular dynamics simulations and quantitative phonon-defect scattering rate analysis, where the behaviour of thermal conductivity with dose is attributed to the accumulation and agglomeration of scattering centres at lower doses. Beyond a threshold dose, a crystalline-amorphous transition was observed., Manipulating the flow of heat at the nanoscale is difficult because it requires the ability to tune the thermal properties of tiny structures. Here, the authors locally change the thermal conductivity of an individual silicon nanowire by irradiating it with helium ions.

We investigate the growth, purity, grain structure/morphology, and electrical resistivity of 3D platinum nanowires synthesized via electron beam induced deposition with and without an in situ pulsed laser assist process which photothermally couples to the growing Pt–C deposits. Notably, we demonstrate: 1) higher platinum concentration and a coalescence of the otherwise Pt–C nanogranular material, 2) a slight enhancement in the deposit resolution and 3) a 100-fold improvement in the conductivity of suspended nanowires grown with the in situ photothermal assist process, while retaining a high degree of shape fidelity.

The nanoscale oxidation mechanisms and kinetics of a model β-NiAl system were investigated using in situ closed-cell gas reaction scanning transmission electron microscopy (STEM). Here, we directly visualize the dynamic structural and chemical changes that occur during high-temperature oxidation at a high spatial resolution of 50.3Ni–49.7Al (at.%) nanoparticles under static air conditions at 730 Torr with heating up to 750 °C at 5 °C/s. A MEMS-based gas cell system, with microfabricated heater devices and a gas delivery system, was used to reveal site-specific oxidation initiation sites. Through time-resolved annular dark-field STEM imaging, we tracked the nanoscale oxidation kinetics of Al2O3. After oxidation at 750 °C, nucleation of voids at the Ni/Al2O3 interface was observed along a NiAl grain boundary, followed by the formation of faceted NiO crystals. Small faceted cubic crystals of NiO were formed at the initial stage of oxidation at high PO2 due to the outward self-diffusion of Ni2+ ions, followed by the formation of a mixture of metastable and stable α-Al2O3 at the oxide/metal interface that is attributed to a PO2 decrease with oxidation time, which agreed with thermodynamic modeling calculations. The results from these in situ oxidation experiments in the β-NiAl system are in agreement with the established oxidation mechanisms; however, with in situ closed-cell gas microscopy it is now feasible to investigate nanoscale oxidation mechanisms and kinetics in real time and at high spatial resolution and can be broadly applied to understand the basic high-temperature oxidation mechanisms for a wide range of alloy compositions.

Aluminum particles are widely used as a metal fuel in solid propellants. However, poor combustion efficiencies and two-phase flow losses result due in part to particle agglomeration. Recently, engineered composite particles of aluminum (Al) with inclusions of polytetrafluoroethylene (PTFE) or low-density polyethylene (LDPE) have been shown to improve ignition and yield smaller agglomerates in solid propellants. Reductions in agglomeration were attributed to internal pressurization and fragmentation (microexplosions) of the composite particles at the propellant surface. Here, we explore the mechanisms responsible for microexplosions in order to better understand the combustion characteristics of composite fuel particles. Single composite particles of Al/PTFE and Al/LDPE with diameters between 100 and 1200 µm are ignited on a substrate to mimic a burning propellant surface in a controlled environment using a CO 2 laser in the irradiance range of 78–7700 W/cm 2 . The effects of particle size, milling time, and inclusion content on the resulting ignition delay, product particle size distributions, and microexplosion tendencies are reported. For example particles with higher PTFE content (30 wt%) had laser flux ignition thresholds as low as 77 W/cm 2 , exhibiting more burning particle dispersion due to microexplosions compared to the other materials considered. Composite Al/LDPE particles exhibit relatively high ignition thresholds compared to Al/PTFE particles, and microexplosions were observed only with laser fluxes above 5500 W/cm 2 due to low LDPE reactivity with Al resulting in negligible particle self-heating. However, results show that microexplosions can occur for Al containing both low and high reactivity inclusions (LDPE and PTFE, respectively) and that polymer inclusions can be used to tailor the ignition threshold. This class of modified metal particles shows significant promise for application in many different energetic materials that use metal fuels.

Direct write with a liquid precursor using an ion beam in situ, allows fabrication of nanostructures with higher purity than using gas phase deposition. Specifically, positively charged helium ions, when compared to electrons, localize the reaction zone to a single-digit nanometer scale. However, to control the interaction of the ion beam with the liquid precursor, as well as enable single digit fabrication, a comprehensive understanding of the radiolytic process, and the role of secondary electrons has to be developed. Here, we demonstrate an approach for directly writing platinum nanostructures from aqueous solution using a helium ion microscope, and discuss possible mechanisms for the beam-induced particle growth in the framework of Born-Oppenheimer and real-time electron dynamics models. We illustrate the nanoparticle nucleation and growth parameters through data analysis of in situ acquired movie data, and correlate these results to a fully encompassing, time-dependent, quantum dynamical simulation that takes into account both quantum and classical interactions. Finally, sub-15 nm resolution platinum structures generated in liquid are demonstrated.

Catalytic oxidation of alcohols often requires the presence of expensive transition metals. Herein, it is shown that earth-abundant Fe atoms dispersed throughout a nitrogen-containing carbon matrix catalyze the oxidation of benzyl alcohol and 5-hydroxymethylfurfural by O2 in the aqueous phase. The activity of the catalyst can be regenerated by a mild treatment in H2 . An observed kinetic isotope effect indicates that β-H elimination from the alcohol is the kinetically relevant step in the mechanism, which can be accelerated by substituting Fe with Cu. Dispersed Cr, Co, and Ni also convert alcohols, demonstrating the general utility of metal-nitrogen-carbon materials for alcohol oxidation catalysis. Oxidation of aliphatic alcohols is substantially slower than that of aromatic alcohols, but addition of 2,2,6,6-tetramethyl-1-piperidinyloxy as a co-catalyst with Fe can significantly improve the reaction rate.

The Pd- and Pt-based $AB{\mathrm{O}}_{2}$ delafossites are a unique class of layered, triangular oxides with two-dimensional electronic structure and a large conductivity that rivals the noble metals. Here, we report successful growth of the metallic delafossite $\mathrm{PdCo}{\mathrm{O}}_{2}$ by molecular beam epitaxy (MBE). The key challenge is controlling the oxidation of Pd in the MBE environment where phase segregation is driven by the reduction of $\mathrm{PdCo}{\mathrm{O}}_{2}$ to cobalt oxide and metallic palladium. This is overcome by combining low-temperature (300 \ifmmode^\circ\else\textdegree\fi{}C) atomic layer-by-layer MBE growth in the presence of reactive atomic oxygen with a postgrowth high-temperature anneal. Thickness dependence (5--265 nm) reveals that in the thin regime (75 nm), the resistivity scales inversely with thickness, likely dominated by surface scattering; for thicker films, the resistivity approaches the values reported for the best bulk crystals at room temperature, but the low-temperature resistivity is limited by structural twins. This work shows that the combination of MBE growth and a postgrowth anneal provides a route to creating high-quality films in this interesting family of layered, triangular oxides.

Grain-boundary (GB) structures and energies are often calculated and have revealed correlations between the GB energy and change in electron density at the GB. In this work, the plasmon peak in valence electron energy-loss spectroscopy (VEELS) was used to determine the variation in electron density across four well-characterized GBs in Al, spanning a range of known GB energies. The results show that the plasmon energy is lower at the GB than in the adjacent grains due to a decrease in electron density, and the GB energy increases proportional to the density decrease. The decrease in electron density also extends further into adjacent grains with increasing GB energy, extending beyond the geometric changes, or physical width, revealed by electron microscopy. Plasmon damping also increases with increasing GB energy, indicative of increasing disruption of the electron density with increasing GB energy. These results demonstrate that VEELS can be a valuable tool for detecting small electron density changes at GBs, and this change clearly influences, and is correlated to, the GB energy.

Isotopes represent a degree of freedom that might be exploited to tune the physical properties of materials while preserving their chemical behaviors. Here, we demonstrate that the thermal properties of two-dimensional (2D) transition-metal dichalcogenides can be tailored through isotope engineering. Monolayer crystals of MoS2 were synthesized with isotopically pure 100Mo and 92Mo by chemical vapor deposition employing isotopically enriched molybdenum oxide precursors. The in-plane thermal conductivity of the 100MoS2 monolayers, measured using a non-destructive, optothermal Raman technique, is found to be enhanced by ∼50% compared with the MoS2 synthesized using mixed Mo isotopes from naturally occurring molybdenum oxide. The boost of thermal conductivity in isotopically pure MoS2 monolayers is attributed to the combined effects of reduced isotopic disorder and a reduction in defect-related scattering, consistent with observed stronger photoluminescence and longer exciton lifetime. These results shed light on the fundamentals of 2D nanoscale thermal transport important for the optimization of 2D electronic devices.

The 2D transition metal carbides or nitrides, or MXenes, are emerging as a group of materials showing great promise in lithium ion batteries and supercapacitors. Until now, characterization and properties of single-layer MXenes have been scarcely reported. Here, using scanning transmission electron microscopy, we determined the atomic structure of freestanding monolayer Ti3C2Tx flakes prepared via the minimally intensive layer delamination method and characterized different point defects that are prevalent in the monolayer flakes. We determine that the Ti vacancy concentration can be controlled by the etchant concentration during preparation. Density function theory-based calculations confirm the defect structures and predict that the defects can influence the surface morphology and termination groups, but do not strongly influence the metallic conductivity. Using devices fabricated from single- and few-layer Ti3C2Tx MXene flakes, the effect of the number of layers in the flake on conductivity has been de...

Herein, we detail how the morphology of a nanomaterial affects its environmental lifetime in aquatic ecosystems. In particular, we focus on the cube and particle nanostructures of Ag and age them in various aquatic mediums including synthetic hard water, pond water, and seawater. Our results show that in the synthetic hard water and pond water cases, there was little difference in the rate of morphological changes as determined by UV-vis spectroscopy. However, when these samples were analyzed with transmission electron microscopy, radically different mechanisms in the loss of their original nanostructures were observed. Specifically, for the nanocube we observed that the corners of the cubes had become more rounded, whereas the aged nanoparticles formed large aggregates. Most interestingly, when the seawater samples were analyzed, the nanocubes showed a substantially higher stability in maintaining the nano length scale in comparison to nanoparticles overtime. Moreover, high-resolution transmission electron microscopy analysis allowed us to determine that Ag+ ions diffused away from both the edge and from the faces of the cube, whereas the nanoparticle rapidly aggregated under the harsh seawater conditions.

A series of carbon-supported, Bi-promoted Pt catalysts with various Bi/Pt atomic ratios was prepared by selectively depositing Bi on Pt nanoparticles. The catalysts were evaluated for 1,6-hexanediol oxidation activity in aqueous solvent under different dioxygen pressures. The rate of diol oxidation on the basis of Pt loading over a Bi-promoted catalyst was 3 times faster than that of an unpromoted Pt catalyst under 0.02 MPa of O2, whereas the unpromoted catalyst was more active than the promoted catalyst under 1 MPa of O2. After liquid-phase catalyst pretreatment and 1,6-hexanediol oxidation, migration of Bi on the carbon support was observed. The reaction order in O2 was 0 over Bi-promoted Pt/C in comparison to 0.75 over unpromoted Pt/C in the range of 0.02–0.2 MPa of O2. Under low O2 pressure, rate measurements in D2O instead of H2O solvent revealed a moderate kinetic isotope effect (rateH2O/rateD2O) on 1,6-hexanediol oxidation over Pt/C (KIE = 1.4), whereas a negligible effect was observed on Bi-Pt/C (...

Enabling memristive, neuromorphic, and quantum-based computing as well as efficient mainstream energy storage and conversion technologies requires the next generation of materials customized at the atomic scale. This requires full control of atomic arrangement and bonding in three dimensions. The last two decades witnessed substantial industrial, academic, and government research efforts directed toward this goal through various lithographies and scanning-probe-based methods. These technologies emphasize 2D surface structures, with some limited 3D capability. Recently, a range of focused electron- and ion-based methods have demonstrated compelling alternative pathways to achieving atomically precise manufacturing of 3D structures in solids, liquids, and at interfaces. Electron and ion microscopies offer a platform that can simultaneously observe dynamic and static structures at the nano- and atomic scales and also induce structural rearrangements and chemical transformation. The addition of predictive modeling or rapid image analytics and feedback enables guiding these in a controlled manner. Here, we review the recent results that used focused electron and ion beams to create free-standing nanoscale 3D structures, radiolysis, and the fabrication potential with liquid precursors, epitaxial crystallization of amorphous oxides with atomic layer precision, as well as visualization and control of individual dopant motion within a 3D crystal lattice. These works lay the foundation for approaches to directing nanoscale level architectures and offer a potential roadmap to full 3D atomic control in materials. In this paper, we lay out the gaps that currently constrain the processing range of these platforms, reflect on indirect requirements, such as the integration of large-scale data analysis with theory, and discuss future prospects of these technologies.

The high performance of Pd-based intermetallic nanocatalysts has the potential to replace Pt-containing catalysts for fuel-cell reactions. Conventionally, intermetallic particles are obtained through the annealing of nanoparticles of a random alloy distribution. However, this method inevitably leads to sintering of the nanoparticles and generates polydisperse samples. Here, monodisperse PdCu nanoparticles with the ordered B2 phase were synthesized by seed-mediated co-reduction using PdCu nanoparticle seeds with a random alloy distribution (A1 phase). A time-evolution study suggests that the particles must overcome a size-dependent activation barrier for the ordering process to occur. Characterization of the as-prepared PdCu B2 nanoparticles by electron microscopy techniques revealed surface segregation of Pd as a thin shell over the PdCu core. The ordered nanoparticles exhibit superior activity and durability for the oxygen reduction reaction in comparison with PdCu A1 nanoparticles. This seed-mediated co-reduction strategy produced monodisperse nanoparticles ideally suited for structure-activity studies. Moreover, the study of their growth mechanism provides insights into the size dependence of disorder-order transformations of bimetallic alloys at the nanoscale, which should enable the design of synthetic strategies toward other intermetallic systems.

The creep deformation mechanisms at intermediate temperature in ME3, a modern Ni-based disk superalloy, were investigated using diffraction contrast imaging. Both conventional transmission electron microscopy (TEM) and scanning TEM were utilised. Distinctly different deformation mechanisms become operative during creep at temperatures between 677–815 °C and at stresses ranging from 274 to 724 MPa. Both polycrystalline and single-crystal creep tests were conducted. The single-crystal tests provide new insight into grain orientation effects on creep response and deformation mechanisms. Creep at lower temperatures (≤760°C) resulted in the thermally activated shearing modes such as microtwinning, stacking fault ribbons and isolated superlattice extrinsic stacking faults. In contrast, these faulting modes occurred much less frequently during creep at 815°C under lower applied stresses. Instead, the principal deformation mode was dislocation climb bypass. In addition to the difference in creep behaviour and cre...

In complex loading conditions (e.g., sliding contact), mechanical properties, such as strain hardening and initial hardness, will dictate the long-term performance of materials systems. With this in mind, the strain hardening behaviors of Cu/Nb nanoscale metallic multilayer systems were examined by performing nanoindentation tests within nanoscratch wear boxes and undeformed regions (as-deposited). Both the architecture and substrate influence were examined by utilizing three different individual layer thicknesses (2, 20, and 100 nm) and two total film thicknesses (1 and 10 µm). After nano-wear deformation, multilayer systems with thinner layers showed less volume loss as measured by laser scanning microscopy. Additionally, the hardness of the deformed regions significantly rose with respect to the as-deposited measurements, which further increased with greater wear loads. Strain hardening exponents for multilayers with thinner layers (2 and 20 nm, n ≈ 0.018 and n ≈ 0.022, respectively) were less than that determined for 100 nm systems (n ≈ 0.041). These results suggest that single-dislocation-based deformation mechanisms observed for the thinner systems limit the extent of achievable strain hardening. This conclusion indicates that impacts of both architecture strengthening and strain hardening must be considered to accurately predict multilayer performance during sliding contact across varying length scales.

The highly energetic electron beam (e-beam) in a scanning transmission electron microscope (STEM) can induce local changes in the state of matter, ranging from knock-on and atomic movement, to amorphization/crystallization, and to localized chemical/electrochemical reactions. To date, fundamental studies of e-beam induced phenomena and practical applications have been limited by conventional STEM e-beam rastering modes that allow only for uniform e-beam exposures. Here, an automated liquid phase nanolithography method has been developed that enables the direct writing of nanometer scaled features within microfabricated liquid cells. An external e-beam control system, connected to the scan coils of an aberration-corrected STEM, is used to precisely control the position, dwell time, and scan rate of a sub-nanometer STEM probe. Site-specific locations in a sealed liquid cell containing an aqueous solution of H2PdCl4 are irradiated to deposit palladium nanocrystals onto silicon nitride membranes in a highly controlled manner. The threshold electron dose required for the radiolytic deposition of metallic palladium has been determined, the influence of electron dose on the nanolithographically patterned feature size and morphology is explored, and a feedback-controlled monitoring method for active control of the nanofabricated structures through STEM detector signal monitoring is proposed. This approach enables fundamental studies of electron beam induced interactions with matter in liquid cells and opens new pathways to fabricate nanostructures with tailored architectures and chemistries via shape-controlled nanolithographic patterning from liquid-phase precursors.

Recent developments in (scanning) transmission electron microscopy (S)TEM have enabled in-situ investigations of nanoscale transformations. However, understanding the physical and chemical process defining matter transformations via the analysis of large-scale in-situ (S)TEM imaging data remains challenging. Here, we experimentally investigated a reaction-convection-diffusion model to track spatial-temporal patterns in (S)TEM videos of Pt nanoparticle formation and graphene contamination. Model parameters are pursued by statistical model selection algorithms that balance descriptive capability and model parsimony to aid interpretability and suppress overfitting. Besides conventional bottom-up analysis from individual entities, the integrated mathematical model based on partial differential equations (PDE) utilizing pixel level information provides complementary system status that may serve as a feedback for optimizing experiment setting.

Processing of metal hybrid nanocomposites have emerged in the recent years by means of solid-state reactions through severe plastic deformation techniques, resulting in heterogenous microstructures and mechanical properties. Despite the increased scientific interest in these unusual materials, little is known regarding their comparative attributes with respect to a homogeneous material having equivalent nominal composition. This work provides a direct comparison of the microstructure and the hardness evolution between a Zn–3Mg (wt.%) alloy and its hybrid counterpart, after high-pressure torsion (HPT) and after HPT followed by a post-deformation annealing (PDA) treatment. Experimental results indicate that both the alloy and the hybrid reach a similar level of grain refinement after HPT processing, however, grain growth follows different trends after PDA. The HPT-processed alloy exhibits clusters of Mg2Zn11 nanocrystalline domains that coalesce into coarser grains maintaining a unimodal GS distribution after PDA. On the other hand, the hybrid after PDA displays a multimodal GS distribution consisting of ultrafine Mg-rich grains containing MgZn2 and Mg2Zn11 nanoscale intermetallics, in a matrix of coarser dislocation-free Zn grains. These observations were supported by kernel average misorientation (KAM) maps and pole figures obtained through electron backscattered diffraction (EBSD) analysis.

Automated image recognition and analysis techniques were combined with liquid cell transmission electron microscopy to explore the oxidation kinetics of nanocrystalline Fe thin films in a water vapor environment. From in situ microscopy experiments, localized oxidation was observed to initiate in the film then propagate in an unsteady fashion, alternatingly arresting and progressing. The oxidation front propagation occurred via new oxidation sites initiating 10s of nm ahead of the existing front rather than through a continuous expansion mechanism. The oxidation rate was seen to be highly dependent on electron dose rate, with increasing electron dose rate accelerating the oxidation front propagation and increasing the density of oxidation initiation sites. The in situ experiments were also performed in diffraction space where it was seen that Fe2O3 was formed during oxidation. Coupling in situ microscopy with automated image analysis creates new opportunities for studying the early stages of localized corrosion by providing direct observation of oxidation propagation as well as quantification of the oxidation rates and rapid identification of byproducts.

Heterostructured metals have attracted increasing interest because of their unique capability to overcome the strength-ductility tradeoff typically observed in engineering materials. Here, a new strategy for synthesizing heterostructured Zn–Mg hybrids is proposed via high-pressure torsion (HPT) followed by post-deformation annealing (PDA). Experimental results indicate a transition from a relatively homogenous nanograined structure after HPT, to a heterogeneous microstructure, containing a distribution of Mg2Zn11 and MgZn2 intermetallic nanoprecipitates, upon subsequent PDA. This led to a simultaneous increase in hardness and strain rate sensitivity. The observed three-regime strain hardening behavior was suggested to be due to the activation of multiple strengthening mechanisms, including grain refinement, in-situ precipitation, and back-stress strengthening associated with geometrically necessary dislocations. Thus, the mechanical response of Zn–Mg hybrids may be tailored to obtain the desired response for task-specific applications.