Search

Secondary pores are the main reservoir space and transportation channel of oil and gas in reef limestone reservoir. At present, the main method of calculating secondary porosity is restricted by the morphological characteristics of porosity spectrum, regional artificial influence, and accuracy of calculation. We present a new method for calculating secondary porosity of reef limestone reservoir by the nuclear magnetic resonance T 2 spectrum which is calibrated by casting thin section. We begin with analyzing and determining the high correlation between the surface porosity of casting thin section and the total porosity. The objective is confirming the feasibility of the method of calculating secondary porosity by using thin-section information calibrate. Then, we use the surface porosity of thin section as the calibrating data and find the T 2 relaxation time corresponding to the best correlation between the secondary porosity and the secondary surface porosity of casting thin section, that is, the T 2 cutoff value of secondary porosity, through the Monte Carlo method. Finally, we calculate the secondary porosity by using the functional relationship between the secondary surface porosity and the surface porosity. The statistical analysis shows that the method of calculating secondary porosity effectively improves the calculation accuracy of secondary porosity. The secondary porosity calculation results have a high correlation with the reservoir productivity.

A path following control strategy is proposed for the guide ship in the underway replenishment without velocity measurements. Firstly, the detailed models of the ship and external disturbances are ...

In order to obtain the hydrodynamic coefficients that can save cost and meet the accuracy requirements, a new hydrodynamic test platform based on a 6DoF (six degrees of freedom) parallel mechanism is proposed in this paper. The test platform can drive the ship to move in six degrees of freedom. By using this experimental platform, the corresponding hydrodynamic coefficients can be measured. Firstly, the structure of the new device is introduced. The working principle of the model is deduced based on the mathematical model. Then the hydrodynamic coefficients of a test ship model of a KELC tank ship with a scale of 1:150 are measured and 8 typical hydrodynamic coefficients are obtained. Finally, the measured data are compared with the value of a real ship. The deviation is less than 10% which meets the technical requirements of the practical project. The efficiency of measuring the hydrodynamic coefficients of physical models of ships and offshore structures is improved by the device. The method of measuring the hydrodynamic coefficients by using the proposed platform provides a certain reference for predicting the hydrodynamic performance of ships and offshore structures.

Hypothesis Electrorheological fluid (ERF) is a kind of suspension or colloid composed of fine particles and insulating oil as continuous phase. The second miscible liquid phase with less affinity to the particles than the continuous phase is expected to influence particles aggregation, assembly and spanning mesostructures. Hence, it should be possible to tune the rheological and electrorheological properties and stability by the addition of second miscible liquid with different chain length and substituents. Experiments We developed a giant ERF (GERF) with a binary liquid phase (BLP) by the addition of alkane to the silicone oil continuous phase. We studied the shear stress and viscosity under different shear rates, thixotropy and particle size distributions of these suspensions and characterized the concentration variation of GERFs under quiescent conditions by measuring the backscattering light intensity variation through vertical scanning. Findings The dispersed particle size distribution is broadened, which produces higher static yield stress and lower zero-field viscosity than those of a single-liquid-phase GERF. The ER efficiency is much higher with the addition of alkane, reaching 10656, which is 1.8 times larger than that of single-liquid-phase suspensions. We performed 100-day stability testing and found that the GERF with 1-phenyldodecane showed excellent stability and performance.

Single-crystalline halide perovskites with regular morphology are of great significance for laser applications because they can be used to fabricate a natural whispering-gallery-mode resonator. Although enormous efforts have been put to synthesize single-crystalline perovskites, controlling the lateral size and thickness of the crystal, particularly at the nanoscale, is still challenging. Here, we report a facile and high-throughput strategy to selectively one-step create micro/nanoscale size-controlled all-inorganic perovskite single-crystal arrays by surface-tension-confined evaporative assembly. Our method can be used to easily tune the single crystal size and selectively position the single crystal, with versatility in fabricating perovskite single-crystal arrays in a wafer scale. When the patterned size increases from 2 to 25 μm, the width of the CsPbClBr

Here, we analyzed the internal structure of ZnO varistors with X-ray micro-CT technology and showed that the porosity and pore volume at the radial edge is considerably higher than at other regions. Experimental results showed that the breakdown phenomenon usually occurs near the outer edge of circular varistors. The distribution of impulse currents applied to concentric ring electrodes indicated that the current ratio at the edge region increased as the total current increased. The pores are insulating under low electric fields and the current through the pores is almost zero. Hence, the voltage gradient at the edge region is higher than that elsewhere. Additionally, the simulation results were consistent with this assumption. The amounts of open pore defects, which showed a conductive state after break down, increased, and the proportion of the current flow through the pores increased accordingly, which lead to a local temperature rise and breakdown.

The charge transport in polypropylene was studied under DC electric fields at different temperatures. By the experimental measurement and simulation of the BCT model, we studied conduction currents, breakdown strength, and space charge distribution. In particular, the conduction characteristics under high temperature and high field, especially the conduction characteristics before the breakdown, were studied by systematic experiments, and the conduction characteristics and the breakdown mechanism were further studied by simulation. The results show that in the process of measuring conduction currents until breakdown, both high temperature and high electric field will promote charge transport. However, the free volume will increase at high temperature, which will easily lead to faster charge transport and breakdown. In the breakdown process at different temperatures, there are different breakdown mechanisms. At 20–60 °C, the electric breakdown process has mainly occurred in polypropylene film, and the breakdown strength is almost unchanged. At 80 °C, electric breakdown and thermal breakdown act together, and the charge transport is faster, and the breakdown field becomes smaller. Finally, we conclude that thermal stress plays a very important role in charge transport. In a high-temperature environment, the volume expansion of polypropylene will promote charge transport, and the insulation of polypropylene capacitor films will be damaged.

The impact of two nonionic surfactants, namely Span 20 and Span 85, on the electrorheological response and colloidal stability of urea-coated barium titanyl oxalate (BTRU)/silicone oil suspensions is investigated. We quantitatively analyze the surfactant effect on modified ER performance through the measurements of yield stress and current density, as well as the tuned suspension stability through calculation of the Turbiscan stability index (TSI) and naked-eye observations of sedimentation phenomena. The surfactant effect on particle–oil interactions and agglomeration effects is examined by measuring the permeability of silicone oil when mixed with the Span surfactant and the cluster size of particles in dispersing medium, respectively. Our results indicate that with the presence of a Span surfactant, the yield stress of the suspension exhibits a local maximum at certain Span concentrations. We hypothesize that below the optimal Span concentration, the ER properties are enhanced by the increase of the electrostatic interaction between particles. Above the limiting concentration, the ER activity is weakened by the formation of a double-layer surfactant structure that generates a steric hindrance effect. We discover that the addition of the Span surfactant favors the improvement of the particle agglomeration phenomenon, thereby promoting colloidal stability of the suspension. Consequently, in the consideration of both ER properties and suspension stability, an optimal ER fluid with the addition of 0.4 wt% Span 85 is acquired with remarkable integrated ER properties.

The level of hardware or information security can be increased by applying physical unclonable functions (PUFs), which have a high complexity and unique nonreplicability and are based on random physical patterns generated by nature, to anticounterfeiting and encryption technologies. The preparation of PUFs should be as simple and convenient as possible, while maintaining the high complexity and stability of PUFs to ensure high reliability in use. In this study, an all-inorganic perovskite single-crystal array with a controllable morphology and a random size was prepared by a one-step recrystallization method in a solvent atmosphere to generate all-photonic cryptographic primitives. The nondeterministic size of the perovskite nanorods mainly arises from crystal growth in an indeterminate direction, producing a high entropy for the system. The cavity-size-dependent lasing emission behavior of perovskite single crystals was investigated as a preliminary exploration of the generation of all-photonic cryptographic primitives. The lasing-mode number was positively correlated with the length of the perovskite nanorods. Therefore, the prepared perovskite nanorod array with random sizes can be transformed into a quaternary cryptographic key array following encoding rules based on the lasing-mode number. Superior lasing stability was observed for the all-inorganic perovskite under continuous excitation, demonstrating the high reliability of this system.

Metal halide-based perovskite solar cells (PSCs) have developed rapidly due to exceptional optoelectronic properties of perovskite materials (such as high optical absorption coefficient, long charge carrier lifetime, long diffusion length, high carrier mobility and tunable bandgaps) and low-cost fabrication processes. The record power conversion efficiency has exceeded 24%, demonstrating the great potential for photovoltaic application. However, the lead toxicity and instability still present as major obstacles for commercialization. In principle, Pb can be replaced with other less-toxic as well as environmentally benign metals, such as Ag, Na, Sn, Ge, Bi, Sb and Ti, to solve the toxicity issue. Replacing methylammonium (MA(+)) or formamidinium (FA(+)) with cesium (Cs+) represents a promising direction to address the instability issue. Herein, we review the recent progress of all-inorganic cesium lead-free halide PSCs. At the end, we outline challenges and future directions.

The aging performance of zinc oxide (ZnO) varistors doped with aluminum and indium was investigated. Alternating current (AC) accelerated aging voltages of 0.85U1mA, 0.90U1mA and 0.95U1mA were applied to the doped varistors at a temperature of 115 °C for more than 1000 h. The electrical properties of the varistors before and after the aging process were evaluated by measuring their current–voltage, capacitance–voltage, and dielectric characteristics. The results showed that the ZnO varistor samples exhibited stable electrical properties under the applied aging conditions. Degradation rate coefficients (Kt) of 0.03, 0.05 and 0.06 were obtained at AC accelerated aging voltages of 0.85U1mA, 0.90U1mA and 0.95U1mA, respectively. The results indicated that the varistor ceramics should be able to operate safely and continuously under the given conditions for more than 110 years, which meets the requirements of surge arresters in power systems. These findings are important for improving the aging performance of ZnO varistors and the general security and stability of power systems.

Zinc-oxide varistors doped with gallium, indium, and silver were studied. Samples showed excellent electrical properties with a voltage gradient of 467.9 V/mm, a nonlinear coefficient of 68.5, and a barrier height of 2.15 eV. Accelerated burn-in alternating voltages of 80%U1mA, 85%U1mA, and 90%U1mA were applied to the samples for more than 200∼h at a temperature of 115 °C. Doping with silver played an important role in reducing the donor density while also raising the barrier height, which helped restrain the aging process and enhanced the aging stability as a result. These varistors performed better in aging stability tests with degradation rate coefficients of 0.04, 0.06, and 0.07 obtained under the given burn-in voltage. They provide the basis for safe and stable operations of surge arresters.

The high-efficiency photocarrier collection at the interfaces plays an important role in improving the performance of perovskite solar cells (PSCs) because the photocarrier effective diffusion leng...

This paper presents a novel approach for automatic, rapid and efficient micro-droplet mixing on ‘open-surface’ droplet-based microfluidics system via magnetic actuation. A two-step micro-fabrication process was employed to decorate the magnetically functionalized polydimethylsiloxane (PDMS) membrane with micro-pillar arrays (MPA) to reduce the adhesion on resident droplets. Droplet manipulation relies on the localized deformation of the elastic membrane under external magnetic fields, thus relieving the additives of magnetic components to the droplets that is commonly required in conventional magnetism-based actuation. Via integration with peripheral computer-based regulator, swift droplet mixing is realized via controlling the coalescent droplets back and forth to generate internal fluid circulations for enhanced mass transfer within the droplet. The comparison of mixing performance between the coalesce-and-stop and back-and-forth mode was systematically performed, which verifies that the back-and-forth actuation of the droplets can obviously improve the mixing efficiency, and typically a higher driving frequency on the droplet renders a shorter mixing duration. With driving frequency of 2.5 cycles/s, the mixing homogeneity can reach 80% within 0.6 s and reach 90% within 1.5 s. Also, it has been experimentally demonstrated that the proposed system can accelerate the dilution under various volume ratios, including 1:2, 1:5, and 1:10. Finally, we demonstrated that the platform can be used to dynamically manipulate the droplets, allowing the de-pinning effect for molecular concentrating and obvious detection sensitivity enhancement in terms of Surface-Enhanced Raman Scattering (SERS). Owing to the superiorities including programmable efficient mixing and parallel scalability, the study herein offers insights for exploiting cost-effective and versatile microfluidics platform for future application in biological analysis, chemical micro-reactions, and trace molecule detections.

SnO2 quantum dots (QDs) ended with chlorine ions are introduced at the interface of spin-coated TiO2 electron selective layer (ESL)/perovskite to fill the pinholes in the layer and passivate the trapping defects. As a result of the increased interface electron collection and reduced bulk recombination, the planar perovskite solar cell with the QDs modified ESL gives the large power conversion efficiency enhancement from 14.9% to 17.3% and greatly improved stability under the continuous light irradiation.

Recently, surface with desirable gradients has been proved to be a powerful tool for diverse applications from biological systems and chemical analysis to material science. In this work, we demonstrate a versatile and universal approach to realize controllable physicochemical properties in orthogonal gradients on polydimethylsiloxane (PDMS) surface. Based on a novel microfluidics network, we can easily establish the concentration gradients within the microfluidic channel for surface polymerization or chemical deposition to realize the stable characteristic gradient on the PDMS substrate. The method was introduced to prepare surface with two-dimensional physical (roughness) gradients, or combinational physicochemical gradients to study the synergistic effect on interested phenomenon. As a proof of concept, the experimental results show that the as-prepared substrate can effectively influence in various fields, such as protein adsorption and nano-particle immobilization, which can potentially be used for future systematical study in biological systems or practical applications in bio/chemical analysis/sensing.

Scanning electron microscopy, electric field-current density measurements, capacitance-voltage testing, X-ray diffraction analysis, and energy dispersive X-ray spectroscopy were performed to study the effects of rare earth-yttrium and gallium doping on the microstructure and electrical properties of ZnO varistors. Our results indicated that the introduction of gallium and yttrium strengthened the barrier height of grain boundaries and led to a decrease in the grain resistance. Both the voltage gradient and nonlinear coefficient of the samples increased and then decreased as the gallium doping level was increased at a given rare earth-yttrium. The residual voltage ratio and the leakage current varied with the opposite relationship. The findings of this study could help to improve the protective effects of surge protection devices assembled from ZnO ceramic varistors and enhance the stability of power systems.

Recently, wearable pressure sensors have attracted considerable interest in various fields such as healthcare monitoring, intelligent robots, etc. Although artificial structures or conductive materials have been well developed, the trade-off between sensitivity and linearity of pressure sensors is yet to be fully resolved by a traditional approach. Herein, from theoretical analysis to experimental design, we present the novel CPDMS/AgNWs double conductive layer (DCL) to synergistically optimize the sensitivity and linearity of piezoresistive pressure sensors. The facilely fabricated solid microdome array (SDA) is first employed as the elastomer to clarify the unrevealed working mechanism of DCL. Attributed to the synergistic effect of DCL, the DCL/SDA based sensor exhibits ultrahigh sensitivity (up to 3788.29 kPa-1) in an obviously broadened linearity range (0-6 kPa). We also demonstrated that the synergistic effect of DCL can be regulated with use of porous microdome array (PDA) to further optimize the sensing property. The linearity range can be improved up to 70 kPa while preserving the high sensitivity of 924.37 kPa-1 based on the interlocked PDA structure (IPDA), which is rarely reported in previous studies. The optimized sensitivity and linearity allow the competitive DCL/IPDA based sensor as a reliable platform to monitor kinds of physiological signals covering from low pressures (e.g., artery pulses), medium pressures (e.g., muscle expansions), to high pressures (e.g., body motions). We believe that the methodology along with the robust sensor can be of great potential for reliable healthcare monitoring and wearable electronic applications in the future.

Summary In recent years, metal halide perovskite opens the new era of the photovoltaic field. The highest power conversion efficiency has exceeded 23%. Although most of reported perovskite solar cells (PSCs) were fabricated by solution methods, the vacuum thermal evaporation method has its unique advantages, such as easy controlling of film thickness, compatibility with tandem cell designs, flexibility to tune interfaces, free of solvent, etc. In this paper, we review the development and progress of the vacuum thermal evaporation method for fabricating PSCs.

We describe a controllable sliding method for fabricating millions of isolated femto- to nanoliter-sized droplets with defined volume, geometry and position and a speed of up to 375 kHz. In this work, without using a superhydrophobic or superoleophobic surface, arrays of droplets are instantly formed on the patterned substrate by sliding a strip of liquid, including water, low-surface-tension organic solvents and solution, along the substrate. To precisely control the volume of the droplets, we systemically investigate the effects of the size of the wettable pattern, the viscosity of the liquid and sliding speed, which were found to vary independently to tune the height and volume of the droplets. Through this method, we successfully fabricated an oriented single metal–organic framework crystal array with control over their XY positioning on the surface, as characterized by microscopy and X-ray diffraction (XRD) techniques.

Giant electrorheological (GER) fluids exhibit a high yield stress due to saturation surface polarization from contact between neighboring particles. To fine-tune the competitive performance of GER fluids, we modified the surface of the GER particles by adding silicone polyether, which strongly adsorbed at the solid-liquid interface and significantly influenced the dispersion, GER effect and electrical current density of the GER fluid. We discovered that a small amount of silicone polyether could improve the dispersion and reduce the electrical current density of the fluid. However, the steric hindrance effect suppressed the GER performance. Ultimately, an optimal solution was obtained by making tradeoffs among the dispersion, current density, viscosity, anti-sedimentation and ER effect. These tradeoffs were effective because they provided repetitive stability and wide opportunities for industrial usage.

An ideal anti-counterfeiting label not only needs to be unclonable and accurate but also must consider cost and efficiency. But the traditional physical unclonable function (PUF) recognition technology must match all the images in a database one by one. The matching time increases with the number of samples. Here, a new kind of PUF anti-counterfeiting label is introduced with high modifiability, low reagent cost (2.1 × 10-4 USD), simple and fast authentication (overall time 12.17 s), high encoding capacity (2.1 × 10623 ), and its identification software. All inorganic perovskite nanocrystalline films with clonable micro-profile and unclonable micro-texture are prepared by laser engraving for lyophilic patterning, liquid strip sliding for high throughput droplet generation, and evaporative self-assembling for thin film deposition. A variety of crystal film profile shapes can be used as "specificator" for image recognition, and the verification time of recognition technology based on this divide-and-conquer strategy can be decreased by more than 20 times.

The zinc-oxide (ZnO) varistor is widely used to limit the overvoltage in the power systems, and its quality is closely related to the safety of the entire protected system. In this paper, accelerated aging experiments under different current levels were carried out on the ZnO varistors to study the harmonic characteristics of the leakage currents in the aging process. It is found that the proportions of higher order harmonics in leakage currents increase faster after several impulse tests and then a sudden decrease appears before the varistor fails, which is caused by the decrease of the varistor voltage. And based on this, a new criterion for the aging of the ZnO varistor is put forward.

Calcium carbonate biomimetic crystallization remains a topic of interest with respect to biomineralization areas in recent research. It is not easy to conduct high-throughput experiments with only a few macromolecule reagents using conventional experimental methods. However, the emergence of microdroplet array technology provides the possibility to solve these issues efficiently. In this article, surface-tension-confined droplet arrays were used to fabricate calcium carbonate. It was found that calcium carbonate crystallization can be conducted in surface-tension-confined droplets. Defects were found on the surface of some crystals, which were caused by liquid flow inside the droplet and the rapid drop in droplet height during the evaporation. The diameter and number of crystals were related to the droplet diameter. Polyacrylic acid (PAA), added as a modified organic molecule control, changed the CaCO3 morphology from calcite to vaterite. The material products of the above experiments were compared with bulk-synthesized calcium carbonate by scanning electron microscopy (SEM), Raman spectroscopy and other characterization methods. Our work proves the possibility of performing biomimetic crystallization and biomineralization experiments on surface-tension-confined microdroplet arrays.

Lightning is the main cause of transmission line failure, and it is important to improve the lightning protection level of the transmission line for the stability of the power system. Traditional solutions for the shielding failure of transmission lines is to use the electrical geometric model method. However, with the improvement of the voltage level, the physical size increases, and the calculation of lightning protection for ultrahigh-voltage dc lines has a greater difference with operating experience. Based on the Ningxia-Shandong dc transmission lines in China, this study utilised the lead development model to describe the flashover of insulators and the breakdown of the gaps. A comprehensive calculation method of shielding failure trip-out rate considering terrain, earth resistance and weather was proposed. The accuracy was much higher when compared with the traditional calculation and the result can be a reference for other similar calculation for dc lines.

Graphene or reduced graphene oxide (rGO) membrane-based materials are promising for many advanced applications due to their exceptional properties. One of the most widely used synthesis methods for rGO membranes is vacuum filtration of graphene oxide (GO) on a filter membrane, followed by reduction, which shows great advantages such as operational convenience and good controllability. Despite vacuum-filtrated rGO membranes being widely used in many applications, a fundamental question is overlooked: are the top and bottom surfaces of the membranes formed at the interfaces with air and with the filter membrane respectively symmetric or asymmetric? This work, for the first time, reports the asymmetry of the vacuum-filtrated rGO membranes and discloses the filter membranes' physical imprint on the bottom surface of the rGO membrane, which takes place when the filter membrane surface pores have similar dimension to GO sheets. This result points out that the asymmetric surface properties should be cautiously taken into consideration while designing the surface-related applications for GO and rGO membranes.

Patterning biomolecules and cells on substrates is usually a prerequisite for biological analysis and cell studies. A stencil is a versatile tool for sample patterning owing to its reusability and easy operation but it lacks addressable fluid control and programmable change of pattern. Here, we combined the advantages of a microfluidic chip and stencil to design a digitally controlled microfluidic programmable stencil. The key design is automatic passive matrix addressing based on combined application of two types of elastomeric valves. These two valves have distinct actuation thresholds, typically 13.4 psi for a round valve and much higher than 13.4 psi for a rectangle valve. Different types of protein and cell pattern on a 2D substrate could be obtained by controlling the fluid addressing code based on the passive matrix addressing method. An automatic microsampler was also applied to facilitate fast sample selection and introduction in the patterning process. A successful protein and cell pattern was obtained which could be used for downstream analysis and study.

Magnetorheological gel (MRG) excels in the material properties in term of adjustability and sedimentation performance, which could upgrade the performances of the current magnetorheological fluid based adjustable devices for structural control and vibration mitigation. However, the characterization and modelling of the stress-strain hysteresis responses of MRG has not been reported in the past, which are fundamental steps towards engineering applications. In this study, the stress-strain hysteresis of polyurethane based MRG sample with 60% carbonyl iron particle weight fraction was characterized under sinusoidal shear excitations with broad ranges of strain amplitude (5%–100%), excitation frequency (0.1 Hz–2 Hz) and magnetic fields (0–0.91 T). Significant stress overshooting phenomenon were observed under the application of low magnetic fields (0.27 T). A structurally-simple and accurate phenomenological model has been established to capture this unique nonlinearity. By validating the experimental results, the proposed model accurately predicts the hysteretic behaviour and the overshoot of the MRG under the excitation scenarios and the magnetic fields considered. Finally, the support vector machine (SVM) was implemented to provide the solution to the model generalization. The SVM-assisted model showed good agreement with the experimental data and can benefit the efficiency and viability in developing controllable MRG-based devices and system.

In this paper, two kinds of isotropic giant electrorheological elastomers (GERE) were prepared with urea-coated barium titanyl oxalate nanoparticles as dielectric particles filler, poly (dimethyl siloxane) (PDMS) as an elastic matrix and silicone oil as a plasticizer. Such GEREs are far superior to other isotropic and even anisotropic electrorheological elastomers (EREs), showing excellent electrorheological (ER) performance. The theoretic mechanism in elastomers prepared by us should be explained by saturation surface polarization or orientational polarization model. More interestingly, the storage modulus increment (ΔG′) of GEREs displays curvilinear dependence on the electric field due to poor particle mobility and different mobility under different electric fields, rather than a predicted linear variation. After testing their viscoelastic and dielectric properties and microstructures, we found that too high of the powder content leads to the serious agglomeration of particles and the performance degradation of the elastomer. An incorporation of silicone oil improved the dispersion state and wettability between the particles and matrix. At the same time, silicone oil reduced the hardness of the matrix and made the particles align more easily in the PDMS matrix. Lower initial modulus and higher field-induced modulus make GEREs containing silicone oil have ultrahigh storage modulus sensitivity, in which the best-performing sample achieved a storage modulus change exceeding 400 kPa and attained a maximum relative ER effect of 3280% at 3 kV/mm. Finally, the GERE was used to reversibly control the amplitude of circular motion within seconds by varying electric fields, revealing broad potential application in vibration control.

Metal-organic frameworks (MOFs) have attracted considerable attention as novel nanoporous materials that combine the properties of organic and inorganic porous materials. HKUST-1 is one of the most well-developed and representative MOFs with wide applications in gas storage and separation, adsorption, and capture. In this study, we used microfluidics, an advanced technique of manipulation of small fluid volumes in microscale or even nanoscale channels, to investigate the effect of sodium dodecyl sulfate (SDS) on the growth of HKUST-1 crystals. We directly observed the morphological evolution of HKUST-1 crystals through droplet arrays with the SDS concentration gradient. The morphology of HKUST-1 evolved from cubic to cuboctahedron and finally to octahedron with increasing SDS concentration. The study results demonstrated the important role played by anions in solution in the structural regulation of HKUST-1.

High-quality single-wall carbon nanotube (SWCNT) films were lightly fluorinated by treatment with xenon difluoride at room temperature, which led to the formation of ionic C–F bonds on tube walls and controllable p-type doping of the nanotubes. The fluorinated SWCNT films showed improved electronic conductivity and a higher work function. In addition, the fluorination process increased the areal density of SWCNT films and decreased their surface roughness, leading to better interface contact between them and silicon. As a result, a heterojunction solar cell constructed using the lightly fluorinated SWCNT film has a high power conversion efficiency of 13.6% and excellent stability.

In this study, we successively and parallelly slide a solvent strip on a polydimethylsiloxane microwell array to dilute the solution within the microwells. A total of 60 concentration gradients were generated one by one along the sliding direction within minutes while simultaneously forming 60 microwells with the same concentration perpendicular to the sliding direction. Using theoretical calculations, simulated predictions and experimental verification, we could regulate the concentration gradient on the microwell array by tuning the parameters of the sliding head and sliding speed. Afterwards, we cultured human non-small cell lung cancer cells and produced an anticancer drug concentration gradient on the microwell array by this sliding method. The cell viability was examined to demonstrate the potential of this method for high-throughput cell-based drug testing and screening, and this open microwell array method may enable further analysis during a drug-screening process.

High-throughput measurements can be achieved using droplet-based assays. In this study, we exploited the principles of wetting behavior and capillarity to guide liquids sliding along a solid surface with hybrid wettability. Oil-covered droplet arrays with uniformly sized and regularly shaped picoliter droplets were successfully generated on hydrophilic-in-hydrophobic patterned substrates. More than ten thousand 31-pL droplets were generated in 5 s without any sophisticated instruments. Covering the droplet arrays with oil during generation not only isolated the droplets from each other but also effectively prevented droplet evaporation. The oil-covered droplet arrays could be stored for more than 2 days with less than 35% volume loss. Single microspheres, microbial cells, or mammalian cells were successfully captured in the droplets. We demonstrate that Escherichia coli could be encapsulated at a certain number (1-4) and cultured for 3 days in droplets. Cell population and morphology were dynamically tracked within individual droplets. Our droplet array generation method enables high-throughput processing and is facile, efficient, and low-cost; in addition, the prepared droplet arrays have enormous potential for applications in chemical and biological assays.

Metal–organic frameworks (MOFs), produced by metal ions coordinated to organic linkers, have attracted increasing attention in recent years. For the utilization in MOFs in numerous applications, achieving positioned MOF growth on surfaces is essential to fabricate multiple-functional devices. We develop a novel miniaturized method to realize surface-tension-confined assembly of HKUST-1 in femtoliter droplet arrays. HKUST-1 crystal arrays grown by evaporation-induced crystallization are observed, and five typical crystal morphologies (i.e., hexagonal, irregular hexagonal, triangular, arc-like and ribbon-like crystals) are found in the large area on the patterned substrate during crystallization. Our research provides a better understanding of the formation mechanism of MOF crystals in confined sessile droplets. The key factors determining HKUST-1 single-crystal growth are the internal flows in an evaporating droplet and consequently aggregation induced by the combination of metallic Cu(II) and BTC ions. Understanding the formation of different morphologies of HKUST-1 crystals is useful to guide the production of crystals with desired shapes for various applications.

Most of the existing calibration methods for binocular stereo vision sensor (BSVS) depend on high-accuracy target with feature points that are difficult to manufacture and costly. In complex light conditions, optical filters are used for BSVS, but they affect imaging quality. Hence, the use of a high-accuracy target with certain-sized feature points for calibration is not feasible under such complex conditions. To solve these problems, a calibration method based on unknown-sized elliptical stripe images is proposed. With known intrinsic parameters, the proposed method adopts the elliptical stripes located on the parallel planes as a medium to calibrate BSVS online. In comparison with the common calibration methods, the proposed method avoids utilizing high-accuracy target with certain-sized feature points. Therefore, the proposed method is not only easy to implement but is a realistic method for the calibration of BSVS with optical filter. Changing the size of elliptical curves projected on the target solves the difficulty of applying the proposed method in different fields of view and distances. Simulative and physical experiments are conducted to validate the efficiency of the proposed method. When the field of view is approximately 400 mm × 300 mm, the proposed method can reach a calibration accuracy of 0.03 mm, which is comparable with that of Zhang’s method.

A novel Si/Sn composite anode material with unique ribbon structure was synthesized by Mechanical Milling (MM) and the structural transformation was studied in the present work. The microstructure characterization shows that Si/Sn composite with idealized entangled ribbon structured can be obtained by milling the mixture of the starting materials, Si and Sn for 20 h. According to the calculated results based on the XRD data, the as-milled 20 h sample has the smallest avergae crystalline size. It is supposed that the flexible ribbon structure allows for accommodation of intrinsic damage, which significantly improves the fracture toughness of the composite. The charge and discharge tests of the as-milled 20 h sample have been performed with reference to Li+/Li at a current density of 400 mA g−1 in the voltage from 1.5 to 0.03 V (vs Li/Li+) and the result shows that the initial capacity is ∼1400 mA h g−1, with a retention of ∼1100 mA h g−1 reversible capacity after 50 cycles, which is possible serving as the promising anode material for the lithium ion battery application.

This article is a concise overview about the developing microfluidic systems named surface-tension-confined droplet microfluidics (STORMs). Different from traditional complexed droplet microfluidics which generated and confined the droplets by three-dimensional (3D) poly(dimethylsiloxane)-based microchannels, STORM systems provide two-dimensional (2D) platforms for control of droplets. STORM devices utilize surface energy, with methods such as surface chemical modification and mechanical processing, to control the movement of fluid droplets. Various STORM devices have been readily prepared, with distinct advantages over conventional droplet microfluidics, which generated and confined the droplets by 3D poly(dimethylsiloxane)-based microchannels, such as significant reduction of energy consumption necessary for device operation, facile or even direct introduction of droplets onto patterned surface without external driving force such as a micropump, thus increased frequency or efficiency of droplets generation of specific STORM device, among others. Thus, STORM devices can be excellent alternatives for majority areas in droplet microfluidics and irreplaceable choices in certain fields by contrast. In this review, fabrication methods or strategies, manipulation methods or mechanisms, and main applications of STORM devices are introduced.

The progressive current degradation and breakdown behaviors of GaN-based light emitting diodes under high reverse-bias stress are studied by combining the electrical, optical, and surface morphology characterizations. The current features a typical "soft breakdown" behavior, which is linearly correlated to an increase of the accumulative number of electroluminescence spots. The time-to-failure for each failure site approximately obeys a Weibull distribution with slopes of about 0.67 and 4.09 at the infant and wear-out periods, respectively. After breakdown, visible craters can be observed at the device surface as a result of transient electrostatic discharge. By performing focused ion beam cuts coupled with scan electron microscope, we observed a local current shunt path in the surface layer, caused by the rapid microstructure deterioration due to significant current heating effect, consistent well with the optical beam induced resistance change observations.