Search

Metal-organic frameworks (MOFs) are among the most promising materials for next-generation energy storage systems. However, the impact of particle morphology on the energy storage performances of these frameworks is poorly understood. To address this, here we use coordination modulation to synthesise three samples of the conductive MOF Cu

Integrating diamond with GaN high electron mobility transistors (HEMTs) improves thermal management, ultimately increasing the reliability and performance of high-power high-frequency radio frequency amplifiers. Conventionally, an amorphous interlayer is used before growing polycrystalline diamond onto GaN in these devices. This layer contributes significantly to the effective thermal boundary resistance (TBReff) between the GaN HEMT and the diamond, reducing the benefit of the diamond heat spreader. Replacing the amorphous interlayer with a higher thermal conductivity crystalline material would reduce TBReff and help to enable the full potential of GaN-on-diamond devices. In this work, a crystalline Al0.32Ga0.68N interlayer has been integrated into a GaN/AlGaN HEMT device epitaxy. Two samples were studied, one with diamond grown directly on the AlGaN interlayer and another incorporating a thin crystalline SiC layer between AlGaN and diamond. The TBReff, measured using transient thermoreflectance, was improved for the sample with SiC (30 ± 5 m2 K GW-1) compared to the sample without (107 ± 44 m2 K GW-1). The reduced TBReff is thought to arise from improved adhesion between SiC and the diamond compared to the diamond directly on AlGaN because of an increased propensity for carbide bond formation between SiC and the diamond. The stronger carbide bonds aid transmission of phonons across the interface, improving heat transport.

Metal sulfide and metal oxide alloys of the form Mo1-x W x S2 and Mo1-x W x O3 (0 ≤ x ≤ 1) are synthesized with varying nominal stoichiometries (x = 0, 0.25, 0.50, 0.75, and 1.0) by thermolysis of the molecular precursors MoL4 and WS(S2)L2 (where L = S2CNEt2) in tandem and in various ratios. Either transition-metal dichalcogenides or transition-metal oxides can be produced from the same pair of precursors by the choice of reaction conditions; metal sulfide alloys of the form Mo1-x W x S2 are produced in an argon atmosphere, while the corresponding metal oxide alloys Mo1-x W x O3 are produced in air, both under atmospheric pressure at 450 °C and for only 1 h. Changes in Raman spectra and in powder X-ray diffraction patterns are observed across the series of alloys, which confirm that alloying is successful in the bulk materials. For the oxide materials, we show that the relatively complicated diffraction patterns are a result of differences in the tilt angle of MO6 octahedra within three closely related unit cell types. Alloying of Mo and W in the products is characterized at the microscale and nanoscale by scanning electron microscopy-energy-dispersive X-ray spectroscopy (EDX) and scanning transmission electron microscopy-EDX spectroscopy, respectively.

The synthesis of colloidal semiconductor nanocrystals (NCs) from single-source precursors offers simplified manufacturing processes at the cost of reduced atom efficiency. Self-capping routes have the potential to maximise this efficiency although investigation has so far been limited to organic solvents. Here we present the synthesis of copper sulfide NCs via the decomposition of a copper dithiocarbamate complex in water. Nanocrystalline covellite particles were prepared without the need for additional capping ligand and exhibited a hollow nanosphere morphology. Mass spectrometry of the water-stable NCs indicated the presence of a number of surface ligands, including a small amine fragment of the single-source precursor (SSP) complex. A broad plasmon resonance in the near-infrared (NIR) at 990 nm was also observed and the photothermal effect of this demonstrated. Cytotoxicity experiments indicated cell viability remained above 95% for NC concentrations up to 1 mg mL−1, indicating high biocompatibility.

Accurately determining the morphology and hence the true surface areas of catalytic nanoparticles remains challenging. For many chemically synthesised nanoparticle suspensions conventional BET surface area measurements are often not feasible due to the large quantities of material required. For platinum, a paradigmatic catalyst, this issue is further complicated by the propensity of this metal to form porous aggregate structures comprised of smaller (ca. 2-5 nm) crystallites as opposed to continuous solid structures. This dendritic/porous particulate morphology leads to a large but poorly defined 'active' surface which is difficult to measure accurately. Here we compare, single nanoparticle electrochemistry with three dimensional (3D) electron tomography and quantitative 2D high-angle annular dark-field (HAADF) scanning transmission electron microscopy (STEM) analysis to yield insights into the porosity and chemically accessible surface area of a 30 nm diameter commercial Pt nanoparticle catalyst. Good quantitative agreement is found between 2D and 3D STEM-based measurements of the particle morphology, density and size distribution. Both 3D STEM tomography and single nanoparticle electrochemical measurements allow quantification of the surface area but the electrocatalytic surface area is found to be 2.8× larger than is measured in STEM; indicating the importance of the atomic scale roughness and structure (

Self-assembling conjugated polymer nanoparticles containing PVKand PLGA-PEG as a matrix polymer were doped with both a luminescentrare-earth complex and magnetic nanoparticles (SPIONs),giving rise to materials that are both luminescent and magnetic.Nanoparticle sizes ranged from 80–110 nm without SPIONs andshowed an increase in size (200–1000 nm) with additional SPIONcontent (11–54%). Quantum yields (QYs) of 24% and 18% weremeasured for systems without and with 11% SPIONs, respectively.Optical properties were stable and suitable for biological imagingapplications.

There is a critical research need for efficient luminescent colloidal nanocrystals, free from cadmium and lead whose toxicity subjects them to usage restrictions, with applications from display devices to biology. Approaches to directly replace cadmium-based materials have mainly focused on indium phosphide-based nanocrystals, however these too are subject to concerns over toxicity. Few other alternatives have been found that can compete with the emission range and efficiency of Cd and Pb-based nanocrystals. Group III-nitride nanocrystals, and their alloys, offer the exciting potential to tune bandgap energies from the ultraviolet to the near infrared yet a robust route towards efficient luminescent nitride nanocrystals is lacking. Here, the synthesis of photoluminescent indium zinc nitride quantum dots exhibiting tunable emission through the visible to near infrared spectra region, with quantum yields of up to 30% is reported. Capping the nanocrystals with both a GaN and ZnS shell significantly increased air stability and emission quantum yields. A proof-of-principle indium zinc nitride nanocrystal light emitting diode is also demonstrated. This work overcomes the significant challenges that have prevented the full exploration of nitride-based semiconductor nanocrystal development, providing a new system for further exploration as a heavy-metal free alternative to current state-of-the-art materials.

Zinc nitride (Zn3N2) colloidal quantum dots are composed of nontoxic, low-cost, and earth-abundant elements. The effects of quantum confinement on the optical properties and charge dynamics of these dots are studied using steady-state optical characterization and ultrafast fluence-dependent transient absorption. The absorption and emission energies are observed to be size-tunable, with the optical band gap increasing from 1.5 to 3.2 eV as the dot diameter decreased from 8.9 to 2.7 nm. Size-dependent absorption cross sections (σ = 1.22 ± 0.02 × 10–15 to 2.04 ± 0.03 × 10–15 cm2), single exciton lifetimes (0.36 ± 0.02 to 0.65 ± 0.03 ns), as well as Auger recombination lifetimes of biexcitons (3.2 ± 0.4 to 5.0 ± 0.1 ps) and trions (20.8 ± 1.8 to 46.3 ± 1.3 ps) are also measured. The degeneracy of the conduction band minimum (g = 2) is determined from the analysis of the transient absorption spectra at different excitation fluences. The performance of Zn3N2 colloidal quantum dots thus broadly matches that of established visible light emitting quantum dots based on toxic or rare elements, making them a viable alternative for QD-LED displays.

Functionalization of graphene is fundamental to facilitating its processing and offers a wide scope for advanced applications. Here we demonstrate a facile, highly efficient and mild covalent functionalization of graphene using HNO3 vapour. This results in functionalized few-layer graphene (FLG) that is high in both quantity and quality. We fully characterized the structure and defect level of functionalized FLG by X-ray photoelectron spectroscopy, high-resolution transmission electron microscopy and Raman spectroscopy. The results from this analysis show the tunability of the surface oxygen functionalities of FLG achieved through controlling the oxidation temperature without affecting the major intrinsic properties of graphene. This allows for further doping for applications, for example with nitrogen as a metal-free catalyst in the oxygen reduction reaction.

Three distinctive doping effects to modify the electronic and geometric properties of Pd nanocrystals for HCOOH decomposition to H2/CO2 are presented: Bi atoms take preferable residence on higher index sites, which leads to a reduction in HCOOH dehydration; Te atoms dwell favourably on terrace sites, which reduces the rate of dehydrogenation; Ag atoms, without site specificity, induce strong electronic effects to promote the activity on the dwindling number of surface Pd sites at high coverage.

Achieving control of the surface chemistry of colloidal quantum dots (CQDs) is essential to fully exploit their properties in solar cells, but direct measurement of the chemistry and electronic structure in the outermost atomic layers is challenging. Here we probe the surface oxidation and passivation of cation-exchanged PbS/CdS core/shell CQDs with sub nm-scale precision using synchrotron-radiation-excited depth-profiling photoemission. We investigate the surface composition of the topmost 1-2.5 nm of the CQDs as a function of depth, for CQDs of varying CdS shell thickness, and examine how the surface changes after prolonged air exposure. We demonstrate that the Cd is localized at the surface of the CQDs. The surface-localized products of oxidation are identified, and the extent of oxidation quantified. We show that oxidised sulfur species are progressively eliminated as Cd replaces Pb at the surface. A sub-monolayer surface 'decoration' of Cd is found to be effective in passivating the CQDs. We show that the measured energy-level alignments at PbS/CdS colloidal quantum dot surfaces differ from those expected on the basis of bulk band offsets, and are strongly affected by the oxidation products. We develop a model for the passivating action of Cd. The optimum shell thickness (of around 0.1 nm, previously found to give maximised power conversion efficiency in PbS/CdS solar cells) is found to correspond to a trade-off between the rate of oxidation and the introduction of a surface barrier to charge transport.

A series of highly efficient semiconductor nanocrystal (NC) photocatalysts have been synthesized by growing wurtzite-ZnO tetrahedrons around pre-formed CdS, CdSe, and CdTe quantum dots (QDs). The resulting contact between two small but high-quality crystals creates novel CdX/ZnO heterostructured semiconductor nanocrystals (HSNCs) with extensive type-II nanojunctions that exhibit more efficient photocatalytic decomposition of aqueous organic molecules under UV irradiation. Catalytic testing and characterization indicate that catalytic activity increases as a result of a combination of both the intrinsic chemistry of the chalcogenide anions and the heterojunction structure. Atomic probe tomography (APT) is employed for the first time to probe the spatial characteristics of the nanojunction between cadmium chalcogenide and ZnO crystalline phases, which reveals various degrees of ion exchange between the two crystals to relax large lattice mismatches. In the most extreme case, total encapsulation of CdTe by ZnO as a result of interfacial alloying is observed, with the expected advantage of facilitating hole transport for enhanced exciton separation during catalysis.

The charge dynamics at the surface of the transparent conducting oxide and photoanode material ZnO are investigated in the presence and absence of light-harvesting colloidal quantum dots (QDs). The time-resolved change in surface potential upon photoexcitation has been measured in the m-plane ZnO (101̄0) using a laser pump-synchrotron X-ray probe methodology. By varying the oxygen annealing conditions, and hence the oxygen vacancy concentration of the sample, we find that dark carrier lifetimes at the ZnO surface vary from hundreds of μs to ms timescales, i.e. a persistent photoconductivity (PPC) is observed. The highly-controlled nature of our experiments under ultra-high vacuum (UHV), and the use of band-gap and sub-band-gap photoexcitation, allow us to demonstrate that defect states ca. 340 meV above the valence band edge are directly associated with the PPC, and that the PPC mediated by these defects dominates over the oxygen photodesorption mechanism. These observations are consistent with the hypothesis that ionized oxygen vacancy states are responsible for the PPC in ZnO. The effect of chemically linking two colloidal QD systems (type I PbS and type II CdS–ZnSe) to the surface has also been investigated. Upon deposition of the QDs onto the surface, the dark carrier lifetime and the surface photovoltage are reduced, suggesting a direct injection of charge carriers into the ZnO conduction band. The results are discussed in the context of the development of next-generation solar cells.

In this Letter we demonstrate that hydrogen-terminated porous silicon (PSi) layers and powders can serve as highly efficient reductive templates for noble metal salts. The reduction results in metal nanoparticle (NP) formation in the pores of PSi. Gold NP formation has been monitored in-situ by measuring the plasmon resonance response. Pt NPs, formed in the PSi matrix, were investigated by transmission electron microscopy and energy-dispersive X-ray analysis. Furthermore, hybrid Pt/PSi nanocomposites exhibit a high catalytic activity for CO oxidation.

Biomimetic sulfur-deficient indium sulfide (In2.77S4) was synthesized by a template-assisted hydrothermal method using leaves of Mimosa pudica as a template for the first time. The effect of this template in modifying the morphology of the semiconductor particles was determined by physicochemical characterization, revealing an increase in surface area, decrease in microsphere size and pore size and an increase in pore volume density in samples synthesized with the template. X-ray photoelectron spectroscopy (XPS) analysis showed the presence of organic sulfur (S O/S C/S H) and sulfur oxide species ( SO2, SO32−, SO42−) at the surface of the indium sulfide in samples synthesized with the template. Biomimetic indium sulfide also showed significant amounts of Fe introduced as a contaminant present on the Mimosa pudica leaves. The presence of these sulfur and iron species favors the photocatalytic activity for hydrogen production by their acting as a sacrificial reagent and promoting water oxidation on the surface of the templated particles, respectively. The photocatalytic hydrogen production rates over optimally-prepared biomimetic indium sulfide and indium sulfide synthesized without the organic template were 73 and 22 μmol g−1, respectively, indicating an improvement by a factor of three in the templated sample.

The rich elemental composition, surface chemistry, and outstanding electrical conductivity of MXenes make them a promising class of two-dimensional (2D) materials for electrochemical energy storage. To translate these properties into high performance devices, it is essential to develop fabrication strategies that allow MXenes to be assembled into electrodes with tunable architectures and investigate the effect of their pore structure on the capacitive performance. Here, we report on the fabrication of MXene aerogels with highly ordered lamellar structures by unidirectional freeze-casting of additive-free Ti3C2Tx aqueous suspensions. These structures can be subsequently processed into practical supercapacitor electrode films by pressing or calendering steps. This versatile processing route allows a wide control of film thickness, spacing within lamellae (to give electrolyte accessible sites), and densities (over 2 orders of magnitude) and hence gives control over the final properties. The as-prepared MXene aerogel with a density of 13 mg cm(-3) achieves 380 F g(-1) capacitance at 2 mV s(-1) and 75 F g(-1) at 50 mV The calendering of the MXene aerogel into a porous 60 pm thick film with a density of 434 mg cm(-3) leads to a superior rate capability of 309 F g(-1) at 50 mV s(-1). In addition, the rolled electrodes present an improvement in volumetric capacitance of 104 times as compared to the as-prepared MXene aerogel. Finally, the outstanding cyclability of rolled electrodes strengthens their nomination for supercapacitor applications. In this paper we demonstrate the possibilities in tuning the porosity and the electrochemical properties of aerogels highlighting the importance of evaluating new and hybrid processing methods to develop energy storage applications. The simplicity and versatility of the developed fabrication strategy open opportunities for the utilization of MXene lamellae architectures in a wide range of applications requiring controlled porosity including catalysis, filtration, and water purification.