Search

An innovative method is introduced for energy harvesting by combining a bowtie frequency selective rectenna surface with a traditional photovoltaic solar panel. The design of the rectenna antenna surface aims to optimize the geometry of the bowtie antennas for enhanced ambient RF energy absorption and rectification efficiency. Several integration techniques are explored to efficiently merge the RF and solar energy harvesting components into a unified system, considering factors such as spatial arrangement and DC electrical connections in both series and parallel. Tested efficiency analysis under various loads demonstrates the feasibility and effectiveness of the hybrid system as it captures the RF and solar energy and converts it into usable electrical energy. The RF-solar hybrid energy harvesting system can be employed in environment settings where energy sources exist intermittently.

The proliferation of smart devices increases the demand for energy-efficient, battery-free technologies essential for sustaining IoT devices in Industry 4.0 and 5G networks, which require zero maintenance and sustainable operation. Integrating radio frequency (RF) energy harvesting with IoT and 5G technologies enables real-time data acquisition, reduces maintenance costs, and enhances productivity, supporting a carbon-free future. This survey reviews the challenges and advancements in RF energy harvesting, focusing on far-field wireless power transfer and powering low-energy devices. It examines miniaturization, circular polarization, fabrication challenges, and efficiency using the metamaterial-inspired antenna, concentrating on improving diode nonlinearity design. This study analyzes key components such as rectifiers, impedance matching networks, and antennas, and evaluates their applications in biomedical and IoT devices. The review concludes with future directions to increase bandwidth, improve power conversion efficiency, and optimize RF energy harvesting system designs. [ABSTRACT FROM AUTHOR]

In this paper, we investigate various graphene monolayer nanomesh structures (diodes) formed only by nanoholes, with a diameter of just 20 nm and etched from the graphene layer in different shapes (such as rhombus, bow tie, rectangle, trapezoid, and triangle), and their electrical properties targeting electromagnetic energy harvesting applications. In this respect, the main parameters characterizing any nonlinear device for energy harvesting are extracted from tens of measurements performed on a single chip containing the fabricated diodes. The best nano-perforated graphene structure is the triangle nanomesh structure, which exhibits remarkable performance in terms of its characteristic parameters, e.g., a 420 Ω differential resistance for optimal impedance matching to an antenna, a high responsivity greater than 103 V/W, and a low noise equivalent power of 847 pW/√Hz at 0 V. [ABSTRACT FROM AUTHOR]

This study introduces a rectenna, functioning as an RF envelope detector, utilizing a 16 nm bulk MOS transistor (metal-oxide-semiconductor field-effect transistor) for nonlinear detection. A circuit architecture is presented alongside a detailed design methodology and simulations. The detector efficiently demodulates a 2.4 GHz OOK (On/Off Keying) encoded signal, comprising a 32-bit word, within 320 μs. Remarkably, the circuit operates passively, requiring no voltage supply or bias current, and functions effectively with − 53 dBm input power at the antenna. This capability enables the decoding of 32-bit unsigned integer radio packets as a wakeup radio event. The effectiveness of the envelope detector is substantiated through comprehensive simulations. [ABSTRACT FROM AUTHOR]

This work presents an analysis and design of the two barrier-quantum well asymmetric spacer tunnel layer (QW-ASPAT) diodes for implantable rectenna circuits application. The RF and DC characteristic of a 10×10 μm² QW-ASPAT devices based on GaAs and In0.53Ga0.47As platform was simulated and extracted by using SILVACO atlas software. The highest extracted curvature coefficient, kv value of the both QW-ASPAT devices at zero bias was about 33V-1 compared with the standard structure GaAs/InGaAs was about 13V-1. The effects of changing in the thickness of the thin AlAs-barrier, the well width, and the spacer layer are fully investigated on the non-linear relationship between current and voltage of these diodes. A CV simulation was carried out, and it was found that the addition of the quantum-well layer between spacers and barrier reduced the junction capacitance of the QW-ASPAT device when compared with standard devices. The cut-off frequency of the proposed QW-GaAs and QW-InGaAs devices are 26GHz and 46GHz respectively. Finally, we conclude that the QW-ASPAT device is the best structure and can be used for microwave rectifiers in the miniaturized integrated rectenna systems. [ABSTRACT FROM AUTHOR]

Electromagnetic (EM) RF (radio frequency) energy harvesting in dynamic ambient environments is a challenge for conventional energy harvesting systems such as rectennas. The main challenges are the low efficiency of the collector and low ambient power levels, which makes it hard to consider in industrial applications. Several research works have focused on the design of high-efficiency antennas to achieve an efficient and maximum possible level of RF EM energy harvesting. Their main objective is to improve the EM energy harvesting system by overcoming the low efficiency of the collector, which is the main part of the rectenna system. In this work, we propose and investigate a methodology in terms of EM energy harvesting based on the concentration and focusing of EM energy in a small zone where it can be easily collected and transferred indirectly to the rectenna system. It consists of a focusing device and a methodology to associate the latter with existing RF energy harvesting systems. We demonstrate a focusing metasurface design implemented alongside an off-the-shelf rectenna device at 900 MHz, where an enhanced energy harvested power level up to a linear gain of 8 is achieved compared to the case when only the rectenna is used. Numerical results as well as measurements results in an anechoic chamber are shown. Experimental power received levels are given both in the focusing plane and in time for the validation of the concept. [ABSTRACT FROM AUTHOR]

This work presents the results of the characterization of two 1 × 5 mm2 miniaturized rectennas developed for medical applications. They have been designed for relatively high voltage and high-power applications, given the size of the rectennas. Both rectennas were tested in open-air conditions and surrounded by pork fat and muscle tissues, whose properties are similar to those of the human body. The resonant frequencies of the rectennas were found, and the incident electric field on the rectennas tests was increased. The first chip showed a maximum output voltage of 5.29 V and a maximum output power of 0.056 mW, at 1.446 GHz, under an incident field on the rectenna of 340 V/m, and the second chip, 4.62 V and 4.27 mW, at 1.175 GHz, under 535 V/m. The second rectenna can provide an output power greater than 5 mW. The rectennas presented in this article are beyond the state of the art, as they can deliver about three times more power and voltage than those of similar dimensions reported in the literature. Based on the test results, the efficiency of the rectennas was analyzed at different locations of the human body, considering different thicknesses of tissues with high and low water content. Finally, potential applications are described in which the rectennas could power implantable medical devices or microsurgery tools, for example, pulmonary artery pressure monitors. [ABSTRACT FROM AUTHOR]

Copyright of Informacije MIDEM: Journal of Microelectronics, Electronic Components & Materials is the property of MIDEM Society and its content may not be copied or emailed to multiple sites or posted to a listserv without the copyright holder's express written permission. However, users may print, download, or email articles for individual use. This abstract may be abridged. No warranty is given about the accuracy of the copy. Users should refer to the original published version of the material for the full abstract. (Copyright applies to all Abstracts.)

Herein, we report the design, fabrication, and performance of two wireless energy harvesting devices based on highly flexible graphene macroscopic films (FGMFs). We first demonstrate that benefiting from the high conductivity of up to 1 × 106 S m−1 and good resistive stability of FGMFs even under extensive bending, the FGMFs‐based rectifying circuit (GRC) exhibits good flexibility and RF‐to‐DC efficiency of 53% at 2.1 GHz. Moreover, we further expand the application of FGMFs to a flexible wideband monopole rectenna and a 2.45 GHz wearable rectenna for harvesting wireless energy. The wideband rectenna at various bending conditions produces a maximum conversion efficiency of 52%, 46%, and 44% at the 5th Generation (5G) 2.1 GHz, Industrial Long‐Term Evolution (LTE) 2.3 GHz, and Scientific Medical (ISM) 2.45 GHz, respectively. A 2.45 GHz GRC is optimized and integrated with an AMC‐backed wearable antenna. The proposed 2.45 GHz wearable rectenna shows a maximum conversion efficiency of 55.7%. All the results indicate that the highly flexible graphene‐film‐based rectennas have great potential as a wireless power supplier for smart Internet of Things (IoT) applications. This work demonstrates two wireless energy harvesting devices based on highly flexible graphene macroscopic films (FGMFs) for IoT low‐power applications. Benefiting from the high conductivity (1 × 106 S m−1) and good resistive stability of FGMFs, the proposed flexible rectenna produces a peak conversion efficiency of 52% at 2.1 GHz, and the proposed 2.45 GHz wearable rectenna shows a maximum conversion efficiency of 55.7%. [ABSTRACT FROM AUTHOR]

A novel, polarization-independent, wide-angle reception Chand-Bali nano-antenna is proposed. An adjoint-based optimization algorithm is used to create the same resonance at both linear polarizations of the incident radiation. The nano-antenna optimal parameters reveal that two hot spots with a strong field enhancement are created. These hot-spots could be integrated with metal–insulator–metal (MIM) diodes to form a rectenna for infrared (IR) energy harvesting. The metallic resonators allow for selecting several materials to facilitate the fabrication of the nano-antenna and the MIM diode. The Chand-Bali-based IR rectennas are investigated and simulations demonstrate an improvement of more than one order of magnitude in efficiency compared to ones using traditional nano-antennas. [ABSTRACT FROM AUTHOR]

Abstract A novel 24 GHz circularly polarised metasurface rectenna for wireless power transmission is designed in this study. Based on experimental measurements and retro‐simulation, an effective approach is proposed to extract the parasitic parameters of a Schottky diode. A highly efficient millimetre wave rectifier with a measured efficiency of 63% is constructed based on the exact equivalent circuit parameters of a diode. A circularly polarised metasurface antenna is adopted as the receiving antenna, and the gain is enhanced by introducing metal vias around the metasurface. The antenna and the rectifier are connected directly via a microstrip line. Measurements show that the metasurface antenna has a gain of 11.3 dBic and an axial ratio of 2.5 dB at 24 GHz. The measured conversion efficiency of the rectenna reaches 63% at 300 Ω load when the input power is 15.2 dBm. The rectenna has the advantages of low profile, which can be conformal to the electrical equipment.

In recent years, microwave wireless power transmission (MWPT) has emerged as a promising technology for supplying energy by receiving radiative power without wires and converting it into DC power. A high transmission efficiency is crucial for improving the performance of MWPT systems. To address the challenge of propagation loss, beam synthesis using transmitting antennas has gained significant attention, resulting in several synthesis methods becoming available, including whisper beams, flat-top beams, non-diffractive beams, supergain/superdirective beams, focused beams and adaptive beamforming technique such as time reversal methods. This comprehensive review covers these advanced beam synthesis techniques for MWPT transmitters and provides a detailed comparison of different synthesized beams. The article includes an in-depth discussion on current designs and existing technological challenges, as well as suggestions for future research directions. Although beam synthesis can substantially improve the transmission efficiency, the overall power transfer efficiency of the entire MWPT system still requires improvement as the performance, including impedance matching, is currently only considered at a component level and not at a system level. Furthermore, when using advanced beam synthesis techniques, the engineering and implementation challenges of high power (≥kW) and long-distance (≥km) MWPT become significant issues due to the high cost and large size involved. The review concludes that existing technologies for synthesized beams still require significant long-term efforts to meet the realistic engineering requirements for achieving highly efficient MWPT systems. The joint utilization of beam synthesis techniques and comprehensive system matching/optimization is identified as a research direction with the potential to realize highly efficient MWPT systems, offering foreseeable impacts in both terrestrial and space-based MWPT applications. This review serves as a solid foundation for the design of transmitter antennas in long-distance, high-power MWPT systems, and furthermore provides novel insights for future designs of highly efficient MWPT systems.

The Internet of Things is currently one of the fastest‐growing branches in electronics. The development of energy storage systems and the miniaturization of dedicated printed circuit boards significantly influence that growth. However, the need for batteries and traditional printed circuit boards still limits devices' minimum size, weight, and cost, narrowing the application area. Energy harvesters and wireless power transfer systems fabricated with printed electronics can significantly reduce such devices' weight, size, and cost. Printed electronics technology provides scalable tools for many electronics applications, shortening the validation time and enabling new low‐cost or disposable solutions on lightweight and flexible substrates embedded inside 3D printed structures and directly on device housings. Energy harvesting and wireless power transfer systems in electronic devices can provide enough power to minimize battery capacity and size or even eliminate the need for batteries in low‐power applications. This review presents an adaptation of printed electronics technology in the fabrication of radio frequency energy harvesters and wireless power transfer rectennas for IoT applications. Last, perspectives for development towards greater integration with microsystems, transient electronics with ecofriendly materials, adaptation for next‐generation telecommunication systems, and 3D structural electronics solutions are briefly discussed. [ABSTRACT FROM AUTHOR]

This work presents the design, fabrication, and measured results of a fully integrated miniature rectenna using a novel tunnel diode known as the Asymmetrical Spacer Layer Tunnel (ASPAT). The term rectenna is an abbreviation for a rectifying antenna, a device with a rectifier and antenna coexisting as a single design. The ASPAT is the centrepiece of the rectifier used for its strong temperature independence, zero bias, and high dynamic range. The antenna is designed to be impedance matched with the rectifier, eliminating the need for a matching network and saving valuable real estate on the gallium arsenide (GaAs) substrate. The antenna is fully integrated with the rectifier on a single chip, thus enabling antenna miniaturisation due to the high dielectric constant of GaAs and spiral design. This miniaturisation enables the design to be fabricated economically on a GaAs substrate whilst being comparable in size to a 15-gauge needle, thus unlocking applications in medical implants. The design presented here has a total die size of 4 × 1.2 mm2, with a maximum measured output voltage of 0.97 V and a 20 dBm single-tone 2.35 GHz signal transmitted 5 cm away from the rectenna. [ABSTRACT FROM AUTHOR]

This article presents the design of an array of rectennas operating at 28.3 THz for infrared (IR) energy harvesting applications. The basic element of the array consists of a Vivaldi-dipole rectenna composed of two arms made with different conductors (gold and titanium). A metal-insulator-metal (MIM) tunnel diode is used to rectify the THz ac current. The proposed MIM diode consists of a very thin layer of Al2O3 sandwiched between the two metal electrodes. Arrays of two, three, and four rectennas are investigated. The improvement of the energy captured by coupling several elements in the same structure with a common gap is also investigated. This array architecture, without feeding network, may reduce the number of rectifying diodes and, therefore, decrease losses and increase the overall efficiency. Finally, it has been found that the four-elements rectenna array has a maximum electric field intensity of 62.4 × 104 V/m at 28.3 THz. [ABSTRACT FROM AUTHOR]

Conventional packaging and interconnection methods for two-terminal devices, e.g., diodes often involve expensive and bulky equipment, introduce parasitic effects and have reliability issues. In this study, we propose a built-in packaging method and evaluate its performance compared to probing and wire bonding methods. The built-in packaging approach offers a larger overlap area, improved contact resistance, and direct connection to testing equipment. The experimental results demonstrate a 12% increase in current, an 11% reduction in resistance, and improved performance of the diode. The proposed method is promising for enhancing sensing applications, wireless power transmission, energy harvesting, and solar rectennas. Overall, the built-in packaging method offers a simpler, cheaper, more compact and more reliable packaging solution, paving the way for more efficient and advanced technologies in these domains. [ABSTRACT FROM AUTHOR]

The transmission line impedance of traveling-wave diodes can circumvent resistance-capacitance time constant limitations of metal-insulator-metal diodes in rectennas operating at optical frequencies. We performed three-dimensional simulations of a traveling-wave diode rectenna using a linear finite-element electromagnetic solver. We develop a method to analyze metal-insulator-metal traveling-wave rectennas by using the field profiles from the linear finite-element solver and accounting for the nonlinear current-voltage characteristics during postprocessing. The traveling-wave diode length produces resonance at half surface plasmon wavelength intervals. With optimized cross section and length parameters, we observe a peak system responsivity of 239 μ A / W and a detectivity of 5.7 × 10 4 Jones. [ABSTRACT FROM AUTHOR]

A novel 24 GHz circularly polarised metasurface rectenna for wireless power transmission is designed in this study. Based on experimental measurements and retro‐simulation, an effective approach is proposed to extract the parasitic parameters of a Schottky diode. A highly efficient millimetre wave rectifier with a measured efficiency of 63% is constructed based on the exact equivalent circuit parameters of a diode. A circularly polarised metasurface antenna is adopted as the receiving antenna, and the gain is enhanced by introducing metal vias around the metasurface. The antenna and the rectifier are connected directly via a microstrip line. Measurements show that the metasurface antenna has a gain of 11.3 dBic and an axial ratio of 2.5 dB at 24 GHz. The measured conversion efficiency of the rectenna reaches 63% at 300 Ω load when the input power is 15.2 dBm. The rectenna has the advantages of low profile, which can be conformal to the electrical equipment. [ABSTRACT FROM AUTHOR]

This work describes a dual band compact fully integrated rectenna circuit for implantable medical devices (IMDs). The implantable rectenna circuit consists of tunnel diode 10x10µm2 QW-ASPAT (Quantum Well Asymmetric Spacer Tunnel Layer diode) was used as the RF-DC rectifier due to its temperature insensitivity and nonlinearity compared with conventional SBD diode. SILVACO atlas software is used to design and simulate 100µm2 QW InGaAs ASPAT diode. A miniaturized dual band implantable folded dipole antenna with multiple L-shaped conducting sections is designed using CST microwave suits for operation in the WMTS band is 1.5GHz and ISM band of 5.8GHz. High dielectric constant material Gallium Arsenide (εr=12.94) and folded geometry helps to design compact antennas with a small footprint of 2.84mm3 (1x4.5x0.63) mm3. Four-layer human tissue model was used, where the antenna was implanted in the skin model at depth of 2mm. The 10-dB impedance bandwidth of the proposed compact antenna at 1.5GHz and 5.8GHz are 227MHz (1.4-1.63GHz) with S11 is -22.6dB and 540MHz (5.47-6.02GHz) with S11 is -23.1dB, whereas gains are -36.9dBi, and -24.3dBi, respectively. The output DC voltage and power of the rectenna using two stage voltage doubler rectifier (VDR) are twice that produced by the single stage at input RF power of 10dBm. [ABSTRACT FROM AUTHOR]

Electrically-contacted optical gap antennas are nanoscale interface devices enabling the transduction between photons and electrons. This new generation of device, usually constituted of metal elements (e.g. gold), captures visible to near infrared electromagnetic radiation and rectifies the incident energy in a direct-current (DC) electrical signal. However, light absorption by the metal may lead to additional thermal effects which need to be taken into account to understand the complete photo-response of the devices. The purpose of this communication is to discriminate the contribution of laser-induced thermo-electric effects in the photo-assisted electronic transport. We show case our analysis with the help of electromigrated devices.

Passing through the transformation of wood to coal then to oil and gas, we find ourselves fortunate to witness the next major transformation, which will lead us to the "New Energy Era." Due to advancements in the field of electronics, energy harvesting has attracted great attraction from researchers and scientists to enhance portability and reliability with reduction in battery wastes. Moreover, wearable electronic devices are also becoming quite popular these days because of their usage in a broad range of applications like sports, health sciences, emergency, and so forth. In order to make sure smooth operation and to increase the working time span of these devices, it has become really important to bring wearable devices and radio frequency (RF) energy harvesting to the same platform. RF energy harvesting is one of the best suitable technology for wearable devices. The abundance of RF energy in surroundings and the ability of RF signal to penetrate buildings play an important role to empower wearable devices. One of the major challenges is to improve power conversion efficiency of wearable rectenna for energy harvesting due to requirements of less efficient bio‐compatible materials for such antennas with conformability issues. This article mainly aims to present different wearable rectenna design techniques, reported over the years. It also presents a tabular comparison of rectenna performance in terms of power conversion efficiency and gains for diverse frequency bands, substrate materials, and conducting materials. In addition, this article also includes the challenges and obstacles in designing an efficient RF energy harvesting rectenna for wearable devices. [ABSTRACT FROM AUTHOR]

Wireless power transfer (WPT) is a promising technique used in many applications, like smart terminals, IoT equipment, etc. For WPT systems based on RF rectifying, working in very low power density situation, high-gain rectenna system is of great essential. According to the antenna theory, for the same physical size, higher gain means higher aperture efficiency, which means more power will be received by the antenna instead of being scattered. However, high-gain rectenna usually means narrow beam width and high directivity, which is contradictory to a power harvesting system that need to have wide spatial coverage. In order to realize high aperture efficiency and wide spatial coverage at the same time, a two-dimensional (2-D) multibeam rectenna based on gain enhanced patches and hybrid coupler is proposed, which can improve the 2-D spatial coverage and achieve the maximum 81.5% power receiving efficiency. Simulation and experimental results indicate that the power receiving efficiency is more than 50% with 100° coverage in main beam cutting plane, 70° in H-plane, and 90° in E-plane. The practicality of this letter is fully verified, which can help to provide a guidance for the design of rectenna. [ABSTRACT FROM AUTHOR]

Despite an increasing interest in wearable wireless power transmission (WPT), until now, wearable antennas have been unable to simultaneously harvest from near-field resonant and far-field radiative WPT. Here, a dual-port antenna is proposed, integrating an inductive coil with a broadband monopole for near- and far-field wearable WPT. The coil acts simultaneously as a High Frequency (HF) near-field power receiver and an Ultra-High Frequency (UHF) resonator, enabling the miniaturization of the enclosed broadband monopole, both fabricated using all-textile conductors. On-body, the antenna maintains a 10 dB return loss over a measured 135% fractional bandwidth while maintaining compactness ( $0.312\times 0.312\lambda ^{2}$ ). The antenna is substrate-independent and is demonstrated on two textile substrates with different dielectric properties and thicknesses. In far-field mode, the rectenna maintains over 40% efficiency from sub-1 $\mu \text{W}$ /cm2 power densities. In the near-field, a WPT efficiency up to 80% can be achieved. The simulated Specific Absorption Rate (SAR) shows up to 40 and 20 dBm power reception for HF and UHF operation, respectively, without exceeding the 1.7 W/kg limit. The far-field wearable rectenna is demonstrated powering a Bluetooth Low Energy node using a BQ25504 DC-DC converter from a best-in-class low power density of 0.88 and $0.55~\mu \text{W}$ /cm2 on-body and in-space, respectively.

This paper establishes the practicality of terrestrial microwave power beaming at distances >1 km. To beam microwave power along the surface of the earth, it is necessary to consider and, where possible, exploit the effects of microwave propagation across terrain. Key design considerations include the effect of scattering from surface topography, approaches for characterizing the beam in the presence of multipath, safety, and efficiency. A rapid demonstration at the US Army Research Field in Blossom Point, MD, delivers 1.6 kW of electrical power at a 1046 m standoff from a 5.4-m-diameter X band transmitter. The transmitter is a reflector antenna with a linearly actuated feed horn that can focus the power density at specific standoff distances. Experimental results over cluttered, irregular terrain achieve a 2.3 dB (70%) enhancement in power density at the target site by deliberate exploitation of a ground bounce. A 4 m2 rectenna receiver produces the 1.6 kW of output power at a 73% RF-to-DC conversion efficiency, which exceeds the current state of the art at X band. In addition, a test to destruction of 4 large rectenna arrays demonstrates how overvoltage protection circuits can improve the RF power handling of rectenna arrays by >1 dB. A final experiment demonstrates >1 kW delivered at >1 km distance to a light display. Since these results should readily scale to higher levels of power and performance, recommendations are provided to mature the technology for operational use.

In this paper, we present a harmonic reaction inductive folded dipole antenna (FDA) for a highly efficient rectenna which is close to the fundamental limitation on efficiency. To remove lossy RF circuit components of the rectifier, the proposed antenna topology integrates circuit functionalities for highly efficient rectification, such as impedance transformation to high-impedance, impedance matching, DC blocking, and harmonic reaction. The proposed antenna is connected directly to rectifier diodes. Thus, the rectification efficiency can be improved toward the fundamental limitation restricted by the performance of the rectifier diode. In experimental investigations of the 2.4 GHz band antenna, the antenna radiation efficiency is 99.2%, and the degradation due to integrated circuit functionalities is negligibly small. The 2.4 GHz band bridge rectifier achieves a rectification efficiency of 91.1% at an input power of 30 dBm. This clarifies the effectiveness of the efficiency improvement with the proposed direct connection topology between the proposed FDA and bridge diode.

A W band (75 – 110 GHz) communication link using monolithic integrated single-diode circuits is proposed. The circuits are based on GaAs Schottky diodes with cutoff frequencies around 1.5 THz integrated with on chip folded slot antennas and near-field 3D printed dielectric lenses. The total chip area is $1.4\times3.5$ mm2. The receiver module shows a peak isotropic voltage sensitivity of 12260 mV/mW at 94 GHz, with a noise equivalent power of 12 pW/ $\sqrt {Hz} $ . These results include the slot antenna and a 3 mm radius 3D printed lens. The transmitter acts as a free-space W band signal generator using the non-linear properties of the diode for frequency multiplication. Multiplication orders up to $\times 15$ are tested for input powers of 10 mW. The generated power is measured by a horn antenna placed at a distance of 100 mm from the transmitter and a 2D map for the frequency range 90 – 100 GHz and multiplication orders between $\times 2\ldots \times 15$ is presented. The two circuits are used to demonstrate W band communication links using 1 kHz amplitude modulated input signals with carriers at 6 GHz, X band and in the Ku band. Voltages of hundreds of mV are detected for a distance of 150 mm between transmitter and receiver circuits and tens of mV at 600 mm. The proposed approach can be used as a low cost and low complexity alternative for point-to-point high-speed wireless communications.

This study proposed, for the first time, a newly developed metal–insulator-insulator–metal (MIIM)-based log-spiral rectenna for energy harvesting applications. The designed resonant log-spiral antenna at 28.3 THz forwards the absorbed infrared (IR) electromagnetic (EM) radiations to the installed double insulator-based MIIM rectifying diode. The realized MIIM diode is formed by sandwiching the two insulators among the designed resonant antenna terminals (hot spot region). Antenna terminals are used as the electrodes of the rectifying diode. This novel approach ensures the maximum transfer of captured IR EM radiations by the antenna to the rectifying part with good impedance matching and thus increases the overall conversions efficiency. The study presents an in-depth analysis of the impact of the changing metal types (Au, Al, Ag, and Cu) and insulating materials (Al 2 O 3 , Cu 2 O, Ta 2 O 5 , TiO 2 , and ZnO with10 different formations) on the realized rectenna performance in terms of captured E-field enhancement, I/V , resistivity, and responsivity characteristics. It is found that the overall performance of the proposed double insulator-based rectenna system is better for the asymmetric configuration of Au- Al 2 O 3 - Cu 2 O –Cu and it exhibits 100% enhanced non-linearity as compared to MIM-based configuration. [ABSTRACT FROM AUTHOR]

In this article, a comprehensive review specifically on the applications of rectennas for different wireless systems has been presented. Rectenna systems are used to convert radio-frequency (RF) energy into dc signals. Attracting ever-increasing interest among researchers, the rectenna has occupied a unique position in RF and microwave engineering systems. During the last four decades, the research on rectenna design has been focused on improving the power conversion efficiency (PCE) and compatibility while reducing the design complexity as well. This review article summarizes the overall rectenna research carried out for different applications, viz., wireless power transmission (WPT), wireless sensor networks (WSNs), solar power transmission (SPT), medical implants, and wireless energy-harvesting (WEH) systems. Such a review article has rarely been proposed in the open literature to the best of the authors’ knowledge. The main objectives of the article are to 1) accommodate the key design requirements of the rectenna, 2) study the potential application of rectennas and their possible configurations to achieve desired performance characteristics, and 3) to present a comparative analysis of the performance parameters of the different reported works. [ABSTRACT FROM AUTHOR]

In this paper, a design and implementation of a simple, low cost, efficient rectifier circuit is proposed to eliminate the need for the usual complicated impedance matching network in rectenna harvesting systems. The proposed rectifier circuit consists of a Schottky diode and LC components only. The design is optimized based on the Moss Rose Optimization Algorithm (MROA), which is programmed by using the MATLAB software and then simulated by the Advance Design System (ADS) software. The simulation procedure for finding the rectifier circuit elements using MATLAB is implemented by rewriting the simulation software in C language and utilizing the Mikroelectronica development tool. It is shown that the obtained LC values at 2.4 GHz have offered a minimum value of reflection coefficient (about -38 dB) under stable conditions. The obtained results are compared with some previous works that have used rectenna systems with impedance matching elimination network, and it is found out that the proposed design offer the lowest reflection coefficient. [ABSTRACT FROM AUTHOR]

A new compact patch rectenna is presented in this letter. It consists of a rectangular patch antenna, a Schottky diode, and a harmonic filter with impedance matching to improve the rectifying efficiency. The filter is realized by a series short-ended one-eighth-wavelength microstrip transmission line, which also balances the capacitive impedance of the diode. The impedances of the diode and patch antenna are matched well by tuning the patch antenna and short-ended transmission line. A meander line is used to build a dc output path. For validation, a rectenna working at 2.45 GHz is designed, manufactured, and measured. A maximum rectifying efficiency of 82.2% is realized when the dc load is 400 Ω at an input power of 22.5 dBm. The proposed patch rectenna has potential applications such as rectenna arrays in wireless power transmission. [ABSTRACT FROM AUTHOR]

Remotely driven smart actuator technology by microwave is attractive since it simplifies and reduces the complexity and weight of the remote system. A rectifying antenna (rectenna) array receives and converts microwave power into DC power for actuators, and the power collected from the rectenna array should be accurately allocated and distributed to each actuator. In this research, a new power distribution (PD) logic circuit is studied to control an actuator array effectively. The PD logic circuit was designed and tested to validate it. The preliminary design was tested for a 4 × 4 piezoelectric actuator array with a 16 dual-gate MOSFET array and a computer-controlled 16-channel DAC board. Additionally, power compensation as a remedial approach for a partial power failure of the array was integrated. This PD scheme with a new logic device simplifies the thousands of control cables required for connecting each array element. The performance and limitations of the designed PD circuit are discussed. [ABSTRACT FROM AUTHOR]

The dc power collected by radio frequency energy harvesting (RFEH) absorbing surfaces is limited by their physical aperture. Here, a compact, conformable, and ultrathin sub-1 GHz large-area RFEH surface is proposed based on electrically small ($ka=0.58$) “wire-type” rectenna elements, with an effective area exceeding its physical aperture size. Using optimized large-signal complex source tuning, the rectifiers achieve up to 36% measured power conversion efficiency (PCE) at =20 dBm. The proposed 15 cm-diameter six-element array generates a 27.5 $\mu \text{W}$ at 1 V output from a $0.17~\mu \text{W}$ /cm2 incident power density across a 40 $\text{k}\Omega $ load. Owing to its series connection, the voltage output is boosted, and the load resistance dependence is suppressed enabling over 60% of the maximum RF-to-dc PCE to be preserved for loads between 7 and 100 $\text{k}\Omega $ , with an area-normalized figure-of-merit nearly 100% higher than previous arrays. The proposed array is integrated with a commercial DC-DC converter and demonstrated powering a Bluetooth low energy (BLE) wireless sensor node (WSN) from an unprecedented incident power density of 0.25 $\mu \text{W}$ /cm2. A practical demonstration using a commercial 3 W, 915 MHz Powercast source is presented, showing an 11 m operation range with a 1 V output and illustrating the impact of polarization mismatch on the proposed array. [ABSTRACT FROM AUTHOR]

This communication presents a coplanar waveguide fed rectenna system implemented for efficient Radio frequency energy harvesting at 2.4 GHz Bluetooth/WLAN applications engrossing an overall dimension of 40 × 35 mm2. The antenna is designed on a rectangular patch having four slots etched on the radiator. Also, the ground is introduced with edge slots that are close to the feed line to improve the overall impedance bandwidth providing a gain of 4.12dBi. The E-plane corresponding to the radiation showcases dipole characteristics while the H-plane follows an omnidirectional pattern. The rectifying part comprises a hybrid Tripler circuit which is well matched with the L-shaped input impedance such that most of the received power could be deliberated. The results have demonstrated that the designed rectenna exhibits high conversion efficiency of 66.7% and output DC voltage of 3.47 V for load values of 3 kΩ at 2.4 GHz under the input power of 5 dBm. [ABSTRACT FROM AUTHOR]

In this communication, the novel low cost hybrid energy harvester combining rectifying antenna with the solar cell for feeding the low power energy systems are reported. The bioinspired leaf shaped monopole antenna is designed to work in the most used communication frequency bands such as GSM-1800, UMTS-2100, WIFI-2.45 and LTE-2.65 GHz for the energy harvesting purposes and microstrip low pass filter is also added on the feeding line for the second harmonic rejection for increasing the efficiency of the harvester. The solar cell is placed on the ground plane of the designed leaf shaped antenna for using volumetric space efficiently and obtain a more compact system. The implemented prototype harvester generate 76 mV, 120 mV and 90 mV when the same type receiver antenna feed from the 25 dBm power from the RF source located at a distance of 1 m which satisfies the far field condition of the antenna without solar cell at the 2.15 GHz, 2.45 GHz and 2.65 GHz frequency bands, respectively. After the illumination of its solar cell component with 165 lux, the total harvested voltages are measured as 150 mV, 170 mV and 190 mV at the same frequency bands, respectively. [ABSTRACT FROM AUTHOR]

In this article, a seven-band omnidirectional rectenna is proposed for the first time to harvest RF energy. The designed rectenna operates in the following practical and up-to-date frequency bands: GSM1800 (1.8 GHz), LTE (2.1 GHz), WLAN/Wi-Fi (2.4 and 5.8 GHz), and 5G bands (2.6, 3.5, and 4.9 GHz). To obtain the multiband rectenna, a novel seven-band rectifier is introduced and composed of three optimized single shunt diode rectifiers in parallel. Overall RF-to- dc conversion efficiencies as high as 44.4% @ 1.84 GHz, 43.9% @ 2.04 GHz, 45.4% @ 2.36 GHz, 43.4% @ 2.54 GHz, 36.1% @ 3.3 GHz, 32.4% @ 4.76 GHz, and 28.3% @ 5.8 GHz are achieved at an input power level of −10 dBm. Moreover, a broadband omnidirectional monopole antenna is further codesigned with elaborate impedance matching to the rectifier. The antenna can harvest RF energy in the bandwidth of 1.67–5.92 GHz ($\text{S}_{\mathbf {11}}$ no more than −10 dB) with stable omnidirectional radiation patterns. By integrating the rectifier and the monopole antenna in a low profile, a prototype of the rectenna was manufactured and tested. The experimental results demonstrate that the proposed rectenna has competitive performance in terms of RF-to- dc conversion efficiency and band coverage, indicating enormous potential for numerous battery-free or low-power-needed applications in the real world. [ABSTRACT FROM AUTHOR]

This work describes a novel fully integrated rectenna circuit using tunnelling-based devices for implanted medical devices. An ASPAT (Asymmetric Spacer Layer Tunnel Diode) was used as the active rectifier due to its high non-linearity and temperature insensitivity features. A miniaturized geometry rectenna ($1 \times 5$ mm2) with improved matching characteristics was demonstrated, by integrating a Cockcroft-Walton rectifier with an L-shaped planar folded antenna structure operating at ISM frequency bands. The circuit performance was experimentally explored at various separation distance between transmitter and receiver units. For a 5cm transmission set-up, the rectenna with a single-stage rectifier delivered 0.8V output at 20dBm transmit power. An extended doubler configuration exhibited enhanced performance when multiple stages are used, is predicted to reach 0.24mW output power at 23dBm transmit power and yielding ~1.6V output voltage with an efficiency of 0.12%. These findings can assist in compensating for the degraded antenna gain attributed to the extremely small effective-radiating area of $0.04\lambda $. Furthermore, the ability of controlling the antenna input impedance helps in circumventing the requirement for a matching circuitry thereby offering further reduction in chip size. [ABSTRACT FROM AUTHOR]

In this paper, a dual-band implantable rectenna is proposed for recharging and operating biomedical implantable devices at 0.915 and 2.45 GHz. The rectenna system consists of a compact dual-band antenna based on a meandered-resonator as well as efficient dual-band rectifier circuit. Both components (antenna and rectifier) are integrated inside a capsule device to simulate and experimentally validate the rectenna. The antenna occupies lower volume ( 5 × 5.25 × 0.25 mm 3 ), where compactness is achieved using meandered geometry and a slotted ground plane. It maintains quasi-omnidirectional radiation patterns and peak realized gains of −22.1 dBi (915 MHz) and −19.6 dBi (2.45 GHz); thus, its capability is enhanced to harvest the ambient energy from multiple directions. Moreover, a dual-band rectifier is designed using a dual-branch matching network (an L-matching network and open-circuited stub in each branch) with a radio frequency (RF) to direct current (DC) conversion efficiency of 79.9% for the input power of 1 dBm (lower band: 0.915 GHz) and 72.8% for the input power of 3 dBm (upper band: 2.45 GHz). To validate the concept of the rectenna, the implantable antenna and rectifier are fabricated and attached together inside a capsule device, with the measured results verifying the simulated responses. The proposed rectenna efficiently rectifies two RF signals and effectively superimposes on a single load, thus, providing a distinct advantage compared to single-band rectennas. To the best of the authors' knowledge, this is the first-ever implantable rectenna to perform dual-band RF signal rectification. [ABSTRACT FROM AUTHOR]

Rectifier is a fundamental element of a rectenna system that converts RF energy to direct current (dc). We proposed a triple-band rectifier using a novel matching technique and single series diode topology. First, we designed a single band rectifier and then converted it into a dual- and triple-band rectifier by introducing an appropriate transmission line and shorted stub, respectively, to convert simultaneously multiple RF signals into dc. The proposed rectifier operates at the popular frequency bands of 1.95, 2.7, and 5.8 GHz with power conversion efficiency (PCE) of 65.5%, 62%, and 57.1%, respectively, using a single impedance matching circuit. [ABSTRACT FROM AUTHOR]

The efficiency of a rectenna varies under the influences of receiving polarization tilt angle, operating frequency, input power, and load value in different applications. Yet, no reported rectenna can realize stable efficiency when all these factors vary within a wide range. To solve this problem, an all-polarized rectenna is proposed in this article, composed of a dual-input rectifier and a dual-polarized (DP) antenna. By introducing a novel six-port coupler, the rectifier maintains stable efficiency at wideband, wide input power, and dc load ranges. Moreover, the efficiency of the rectifier keeps stable when the antenna receives power at different polarization tilt angles. Accordingly, a DP antenna with extended bandwidth and 3-dB beamwidth is implemented. Finally, the rectenna is formed. The prototype can maintain beyond 70% of the peak efficiency from 1.7 to 2.5 GHz. At a power density as low as 1 μW/cm2, efficiency can reach 24.4%. Furtherly, the rectenna is demonstrated by forming a battery-less digital clock. The clock can be powered wirelessly by a WiFi router or cellular base station with maximum distances of 1 or 70 m respectively. Besides, the clock can successfully function under significant transmitting-direction deviation or polarization misalignment between the power source and the rectenna. [ABSTRACT FROM AUTHOR]

In this paper, we study the waveform and passive beamforming design for intelligent reflecting surface (IRS)-aided wireless power transfer (WPT). Generalized multi-user and low complexity single-user algorithms are demonstrated based on alternating optimization (AO) framework to maximize the weighted sum output direct current (DC), subject to the transmit power constraints and passive beamforming modulus constraints. The input signal waveform and IRS passive beamforming phase shifts are jointly designed as a function of users’ individual frequency-selective channel state information (CSI). The energy harvester nonlinearity is explored and two IRS deployment schemes, namely frequency selective IRS (FS-IRS) and frequency flat IRS (FF-IRS), are modeled and analyzed. This paper highlights the fact that IRS can provide an extra passive beamforming gain on output DC power over conventional WPT designs and significantly influence the waveform design by leveraging the benefit of passive beamforming, frequency diversity and energy harvester nonlinearity. Even though FF-IRS exhibits lower output DC than the ideal FS-IRS, it still achieves substantially increased DC power over conventional WPT designs. Performance evaluations confirm the significant benefits of a joint waveform and passive beamforming design accounting for the energy harvester nonlinearity to boost the performance of single-user and multi-user WPT systems. [ABSTRACT FROM AUTHOR]

This communication presents an omnidirectional rectenna array with an enhanced RF power distributing strategy. The proposed rectenna array consists of three bidirectional subarray antennas, a $3\times $ 3 RF power distributing network, and a three-element rectifier array. Utilizing the $3\times $ 3 network to redistribute the varying RF power received by the three antennas, the RF-to-dc power conversion efficiency of the rectenna array can be enhanced under the illumination of electromagnetic (EM) waves with arbitrary incident angles. Measurement results reveal that the proposed rectenna array has an improved omnidirectional-harvesting capability compared with the design without RF power distributing strategy, thus can be readily used for RF energy-harvesting applications. [ABSTRACT FROM AUTHOR]

In this paper, a novel dielectric metasurface-inspired multi-beam directional Luneburg lens is proposed as a wireless power transfer medium at 5G mm-wave band. The lens is constructed using dielectric-based unit cells made up of a glide symmetric approach. It is connected with a set of microwave detector integrated multi-port tapered rectangular feeds to convert the received RF energy from different directions to DC power across a combined load. The proposed structure can be a potential candidate to harvest ambient energy from a wide coverage range of around 160° and produce a power conversion efficiency of about 76% for an input power of 14.9 dBm at 24 GHz. [ABSTRACT FROM AUTHOR]

In this work, a dual-polarized wide-angle energy harvester operating at 3.75 GHz is proposed for ambient RF energy harvesting applications. A $4\times 4$ array harvester can efficiently harvest incident RF waves from all polarizations, resulting in high RF-AC efficiency of 94% and final RF-DC efficiency of 34% at 0.02 W/m2 input power density, or −15 dBm input power. This performance is preserved under a wide incident angle up to 65 degrees in TE mode and 75 degrees in TM mode. Owing to its simple power combining configuration, the array can be easily expanded to incorporate more unit cells, increasing the amount of collected power. Not only having the RF-DC conversion function, it is also equipped with a power management circuit to create a usable output voltage level. With this advantage, the harvester is suitable to be employed in real-life applications in which the polarization and angle of incidence are unknown and the incident power is very low.

This paper presents a high-efficiency compact ( $0.016\lambda _{0}^{2}$ ) textile-integrated energy harvesting and storage module for RF power transfer. A flexible 50 $\mu \text{m}$ -thick coplanar waveguide rectenna filament is integrated with a spray-coated supercapacitor to realize an “e-textile” energy supply module. The meandered antenna maintains an $S_{11}< -6$ dB inside and outside the fabric and in human proximity with a 2.3 dBi gain. The rectifier achieves a peak RF-DC efficiency of 80%, across a 4.5 $\text{k}\Omega $ load, and a 1.8 V open-circuit voltage from −7 dBm. The supercapacitor is directly spray-coated on a cotton substrate using carbon and an aqueous electrolyte. When connected to the supercapacitor, the rectifier achieves over an octave half-power bandwidth. The textile-integrated rectenna is demonstrated charging the supercapacitor to 1.5 V (8.4 mJ) in 4 minutes, at 4.2 m from a license-free source, demonstrating a significant improvement over previous rectennas while eliminating power management circuitry. The integrated module has an end-to-end efficiency of 38% at 1.8 m from the transmitter. On-body, the rectenna’s efficiency is 4.8%, inclusive of in-body losses and transient shadowing, harvesting 4 mJ in 32 seconds from 16.6 $\mu \text{W}$ /cm2. It is concluded that e-textile rectennas are the most efficient method for powering wearables from $\mu \text{W}$ /cm2 power densities.

This paper presents a large, modular X-band rectenna array developed for the planned demonstration of a space-to-Earth power beaming link operating at 10 GHz. The array is composed of 16 tiles assembled into a panel greater than 1 m x 1 m in size. To accommodate tests during the early development and construction of the space-based transmitter, the rectenna cells are designed to maximize performance at low power densities using commercial-off-the-shelf Schottky diodes. To increase efficiency at the expense of some field-of-view, each rectenna cell employs a 4-antenna subarray to feed a single diode. Array performance is validated over a 30-dB range of power densities from 1 mW/m2 to 1 W/m2, reaching a total rectenna efficiency in excess of 39% at 1 W/m2. The rectenna array's field of view, defined by the 3-dB beamwidth of its antenna subarray, is 36° ×36°. The DC power collected by each tile is combined in a reconfigurable manner to control the output voltage level for the protection of electrical loads. These results are expected to directly influence the first demonstrations of space-to-Earth power transfer.

In microwave wireless power receivers, impedance matching networks can maximize power transmission from RF to dc. However, they require circuit components and physical space to implement. To circumvent the problem, we present two compact patch rectennas that do not require matching networks. They comprise a patch antenna and rectifying Schottky diodes which are mounted on the ground plane and connected to the patch antenna through metallic vias. The positions of the vias are chosen in such a way that the input impedance of the antenna and that of the rectifying units are conjugately matched. The two rectenna types are all fabricated and tested: one with one rectifying unit and the other with double rectifying units, respectively. Measurements show that the rectenna with the single rectifying unit has the peak RF-dc conversion efficiency of 77% at 2.45 GHz and the dynamic power range (>60%) is 10 dB. The rectenna with the double rectifying units has the peak conversion efficiency of 74.14% at 2.45 GHz and the dynamic power range (>60%) is 10 dB. Both rectennas are good candidates for integrated microwave wireless power receivers due to the removal of the impedance matching networks and the suppression of harmonic components. [ABSTRACT FROM AUTHOR]

In this letter, a compact dual-band rectenna is modeled and developed for low radio frequency (RF) power harvesting. The proposed theoretical model can provide a comprehensive analysis of the rectenna, including the power conversion efficiency (PCE) of the diode, matching efficiency of the rectifier, and total PCE of the rectenna. In the rectenna design, a very compact omnidirectional dielectric resonator antenna (DRA) is proposed with a broad bandwidth exceeding 40%. Meanwhile, a dual-band rectifier is designed based on a single branch in the low-power range with bandwidths covering the two fifth-generation (5G) frequency bands in China (2.515–2.675 and 3.4–3.6 GHz). It was found that the theoretical model can show a high accuracy with the calculation error within 5% in analyzing the dual-band rectifier. The DRA and the dual-band rectifier are integrated to form a compact dual-band rectenna. It shows a higher PCE than those of the existing multiband designs working at similar low-power levels. It is hoped to be implemented in 5G-enabled Internet of Things (IoT) applications for powering wireless sensor nodes. [ABSTRACT FROM AUTHOR]

Numerous efforts have been undertaken to develop rectifying antennas operating at high frequencies, especially dedicated to light harvesting and photodetection applications. However, the development of efficient high frequency rectifying antennas has been a major technological challenge both due to a lack of comprehension of the underlying physics and limitations in the fabrication techniques. Various rectification strategies have been implemented, including metal‐insulator‐metal traveling‐wave diodes, plasmonic nanogap optical antennas, and whisker diodes, although all show limited high‐frequency operation and modest conversion efficiencies. Here a new type of rectifying antenna based on plasmonic carrier generation is demonstrated. The proposed structure consists of a resonant metallic conical nano‐antenna tip in contact with the oxide surface of an oxide/metal bilayer. The conical shape allows for an improved current generation based on plasmon‐mediated electromagnetic‐to‐electron conversion, an effect exploiting the nanoscale‐tip contact of the rectifying antenna, and proportional to the antenna resonance and to the surface‐electron scattering. Importantly, this solution provides rectification operation at 280 THz (1064 nm) with a 100‐fold increase in efficiency compared to previously reported results. Finally, the conical rectifying antenna is also demonstrated to operate at 384 THz (780 nm), hence paving a way toward efficient rectennas toward the visible range. [ABSTRACT FROM AUTHOR]

In this paper, we study multi-user multi-antenna wireless power transfer (WPT) systems, where each antenna at the energy harvesting (EH) nodes is connected to a dedicated non-linear rectifier. We propose optimal transmit strategies which maximize a weighted sum of the average harvested powers at the EH nodes subject to a constraint on the power budget of the transmitter. First, for multiple-input single-output (MISO) WPT systems, we prove that the optimal strategy employs maximum ratio transmission (MRT) beamforming and scalar symbols with arbitrary phases and discrete amplitudes following a probability density function (pdf) with at most two mass points. Then, we prove that for single-input multiple-output (SIMO) WPT systems, the optimal transmit symbol amplitudes are discrete random variables, whose pdf also has no more than two mass points. For general multi-user MIMO WPT, we show that the optimal transmit strategy employs scalar unit-norm symbols with arbitrary phases and at most two beamforming vectors. To determine these vectors, we formulate a non-convex optimization problem and obtain an optimal solution based on monotonic optimization. Since the computational complexity of the optimal solution is high, we propose a low-complexity iterative algorithm to obtain a suboptimal solution, which achieves near-optimal performance. Our simulation results reveal that the proposed transmit strategy for multi-user MIMO WPT systems outperforms baseline schemes based on a linear EH model and a single beamforming vector. For a given transmit power budget, we show that the harvested power saturates when increasing the number of transmit antennas. Finally, we observe that the harvested power region spanned by multiple EH nodes is convex and the power harvested at one EH node can be traded for a higher harvested power at the other nodes. [ABSTRACT FROM AUTHOR]