Search

Fumed silica-filled polypropylene (PP)-based nanodielectrics were studied in this work. To not only improve the dispersion of the silica but also introduce deep charge traps into the polymeric matrix, five types of modified silicas were manufactured with different surface modifications. The modified silica surfaces comprise an inner and a surface layer. The inner layer contains a polar urethane group for tailoring the charge trap properties of the PP/propylene–ethylene copolymer nanocomposites, whereas the surface layer consists of hydrocarbons (ethyl-, tert-butyl-, cyclopentyl-, phenyl-, or naphthalenyl moieties) in order to gain a good dispersion of the silica in the unpolar polymer blend. Scanning electron microscopic pictures proved that these tailored silicas show a much better dispersion than the unmodified one. Thermally stimulated depolarization current measurements revealed the ability of the silica to introduce deep charge traps with low trap density. The trap depth distribution depends on the type of the unpolar surface layer consisting of the different hydrocarbons. Among these five differently modified silicas, the introduction of the one with a surface layer consisting of tert-butyl moieties resulted in the lowest charge injection and the lowest charge current in the nanocomposite, proving good dielectric performance. Additionally, this silica exhibits good dispersion in the polymeric matrix, indicating a promising performance for nanodielectric application.

This study compares different polymer-nanofiller blends concerning their suitability for application as insulating thermoplastic composites for High Voltage Direct Current (HVDC) cable application. Two polymer blends, PP/EOC (polypropylene/ethylene-octene copolymer) and PP/PP-HI (polypropylene/ propylene - ethylene copolymer) and their nanocomposites filled with 2 wt.% of fumed silica modified with 3-aminopropyltriethoxysilane were studied. Morphology, thermal stability, crystallization behavior dynamic relaxation, conductivity, charge trap distribution and space charge behavior were studied respectively. The results showed that the comprehensive performance of the PP/PP-HI composite is better than the one of the PP/EOC composite due to better polymer miscibility and flexibility, as well as lower charging current density and space charge accumulation. Nanosilica addition improves the thermal stability and dielectric properties of both polymer blends. The filler acts as nucleating agent increasing the crystallization temperature, but decreasing the degree of crystallinity. Dynamic mechanical analysis results revealed three polymer relaxation transitions: PP glass transition (β), weak crystal reorientation (α1) and melting (α2). The nanosilica introduced deep traps in the polymer blends and suppressed space charge accumulation, but slightly increased the conductivity. A hypothesis for the correlation of charge trap distribution and polymer chain transition peaks is developed: In unfilled PP/EOC and PP/PP-HI matrices, charges are mostly located at the crystalline-amorphous interface, whereas in the filled PP/EOC/silica and PP/PP-HI /silica composites, charges are mostly located at the nanosilica-polymer interface. Overall, the PP/PP-HI (55/45) nanocomposite with 2 wt.% modified silica and 0.3 wt.% of antioxidants making it a promising material for PP based HVDC cable insulation application with a reduced space charge accumulation and good mechanical properties.

Surface modification of nanoparticles is often utilized to tailor the interfacial properties in dielectric nanocomposites. Introducing different functional groups to the nanoparticles’ surface may induce localized states (traps) that can enhance the dielectric performance of the material depending on their density and energy levels. Furthermore, surface modification of the filler can affect the dispersion quality and crystallization of the nanocomposites which can ultimately alter the dielectric response of the material. In this study, functionalization of silica nanoparticles is demonstrated using 3-(trimethoxysilyl)propyl methacrylate (TMPM) and 1-[3-(trimethoxysilyl)propyl]urea (TMPU) as modifying agents. The effect of such modifications on the crystallization behavior, dispersion quality of the nanoparticles, as well as charge trapping and transport under a medium DC field is studied in nanocomposites based on polypropylene (PP)/ethylene-octene-copolymer (EOC) blends at 1% and 5% of filler concentrations. The results show that both ureido and methacrylate functional groups introduce localized states, but with different energy levels. Nitrogen containing ureido groups in TMPU tend to introduce deeper traps to the filler-polymer interfaces, compared to the methacrylate silane modification. Comparing the two types of surface functionalization, the ureido-functionalized silica resulted in a suppression of space charge formation at the interfaces under a medium DC electric field, despite the relatively larger mean cluster size of nanoparticles.

This paper focuses on novel insulation polypropylene/poly(ethylene-co-octene) (PP/POE) nanocomposites for High Voltage Direct Current (HVDC) cable application. The composites contain silica modified by a solvent-free method using silanes differing in polarity and functional moieties. Thermogravimetric Analysis and Fourier Transform Infrared Spectroscopy showed that the solvent-free method is an effective way to modify silica by silanes. Silica/PP/POE nanocomposites were prepared in a mini twin-screw compounder, and the effect of silica on crystallization, dispersibility and dielectric properties of the samples was investigated. Differential Scanning Calorimetry results showed that the unmodified and modified silicas acted as nucleation agents and increased the onset of the crystallization temperature of the polymeric matrix. Scanning Electron Microscopy images showed that the silica is mostly located in the PP phase matrix. For the PP/POE nanocomposites filled with unpolar silica, a higher trap density (measured by Thermally Stimulated Depolarization Current, TSDC) was found; this might be caused by the larger interfacial area due to a better dispersion of the unpolar silica in the polymeric matrix. Polar silicas introduce deeper traps than the unpolar ones, which is most likely due to the hetero-atom introduction. Nitrogen atoms were found to have the strongest effect on the charge trapping properties. According to these results, amine-modified silica is a promising candidate for PP/POE nanocomposites for HVDC cable applications.

This study evaluated the oxidative stability of olive, sesame, and sunflower oils at different temperatures (4, 25, and 37 ̊C) and in exposure to light for three months. Acidity, peroxide, anisidine, conjugated dienes (CD), and conjugated trienes (CT) and oil stability index (OSI) were measured to investigate the stability of the oils. For all samples, free fatty acid content was almost constant. Temperature and sunlight accelerated the oxidation specifically by an increase in peroxide value and CDs, but anisidine and CTs were not significantly influenced by these variables. The obtained results showed cold-pressed oils had a high tolerance against the formation of the oxidation secondary products. The OSIs were found to be 9.19, 7.06, and 4.73 h for sesame, sunflower, and olive oils, respectively. Among the tested oils, sesame oil had the highest stability. Generally, if storage conditions are optimized, cold-pressed oils can preserve their stability for a longer period. [ABSTRACT FROM AUTHOR]

Novel nanocomposites for dielectric applications-based polypropylene/poly(ethylene-co-octene) (PP/POE) blends filled with nano silica are developed in the framework of the European 'GRIDABLE' project. A tailor-made low-pressure-plasma reactor was applied in this study for an organic surface modification of silica. Acetylene gas was used as the monomer for plasma polymerization in order to deposit a hydrocarbon layer onto the silica surface. The aim of this modification is to increase the compatibility between silica and the PP/POE blends matrix in order to improve the dispersion of the filler in the polymer matrix and to suppress the space charge accumulation by altering the charge trapping properties of these silica/PP/POE blends composites. The conditions for the deposition of the acetylene plasma-polymer onto the silica surface were optimized by analyzing the modification in terms of weight loss by thermogravimetry (TGA). X-ray photoelectron spectroscopy (XPS) and energy-dispersive X-ray fluorescence spectroscopy (EDX) measurements confirmed the presence of hydrocarbon compounds on the silica surface after plasma modification. The acetylene plasma modified silica with the highest deposition level was selected to be incorporated into the PP/POE blends matrix. X-ray diffraction (XRD) showed that there is no new crystal phase formation in the PP/POE blends nanocomposites after addition of the acetylene plasma modified silica. Differential scanning calorimetry results (DSC) show two melting peaks and two crystallization peaks of the PP/POE blends nanocomposites corresponding to the PP and POE domains. The improved dispersion of the silica after acetylene plasma modification in the PP/POE blends matrix was shown by means of SEM–EDX mapping. Thermally stimulated depolarization current (TSDC) measurements confirm that addition of the acetylene plasma modified silica affects the charge trapping density and decreases the amount of injected charges into PP/POE blends nanocomposites. This work shows that acetylene plasma modification of the silica surface is a promising route to tune charge trapping properties of PP/POE blend-based nanocomposites. [ABSTRACT FROM AUTHOR]