Search

10 páginas, 8 figuras, 2 tablas, Air-coupled ultrasound could be considered a suitable on-line technique for the non-invasive industrial testing of potato products manufactured in slices such as dried, fried or baked potato chips. Thus, the aim of the present study is to test the feasibility of air-coupled ultrasound to monitor the modifications in the physicochemical parameters of potato slices caused by drying. For that purpose, the potato slices (6 mm) were air dried (60 °C) for different drying times (15, 90, 180, 300 and 420 min). Air-coupled ultrasonic measurements were taken using through-transmission mode (250 kHz) and different compositional and textural parameters were measured. During drying, the ultrasonic velocity and the impedance increased significantly (p < 0.05) from 509 m/s (raw) to 673 m/s (dried for 420 min) and from 0.544 MRayl (raw) to 0.844 MRayl (dried for 420 min), respectively. Furthermore, a reduction was observed in the material attenuation, which was computed by the increase in the variation of the transmission coefficient with frequency (ΔTC). A principal component regression (PCR) model was successfully trained and validated and it demonstrated the potential capacity of the computed ultrasonic parameters to predict the apparent elastic modulus (E) (R = 0.96) and the Total Relaxation Capacity (TRC) (R = 0.99) during the drying of potato slices. The ultrasonic analysis and experimental set-up proposed in this study may be easily implemented and tested with other products, such as dried, fried or extruded snacks based on fruits or vegetables, for industrial quality control purposes., The authors acknowledge the financial support of the Universitat Politécnica de Valencia (Project 20200421)

[EN] In the dry-cured ham industry, an accurate control of the dry-salting process is especially complex because of the great heterogeneity of the meat pieces and the effect of different operational variables. The main objective of this study was to evaluate the feasibility of using an ultrasound system and methodology, adapted to the industry requirements, for the online monitoring of the ham dry-salting process. For that purpose, hams were dry salted for different times (4, 10, 11, 14, 16 and 30 days) at 2 degrees C. The cushion zone of the ham was placed over the transducers during salting and ultrasonic signals were taken automatically (5 min interval by using pulse-echo mode. Several methods of signal analysis were considered in order to assess the time of flight (TOF). TOF estimations by means of the energy threshold and cross-correlation methods (between the initial ultrasonic signal and the remaining signals measured during salting and between consecutive signals 5 min apart without interpolation) were affected by the low signal-to-noise ratio and the pulse distortion and were discarded for the online monitoring of ham salting. Otherwise, the cross-correlation method between consecutive signals (5 min apart) with interpolation n = 3 (CCM-CS n = 3), between non-consecutive signals (1 h apart) (CCM-NCS) and the phase spectrum method (PSM), provided close estimations of the variation of the TOF, which correlated well with the ham salt gain (R-2 = 0.83 for CCM-CS n = 3, 0.93 for CCM-NCS and 0.90 for PSM). Consequently, the use of ultrasonic pulse-echo TOF measurements could be considered as a simple, non-invasive, non-destructive and reliable technique for the industrial monitoring of the ham dry-salting process., This work was supported by the Spanish Ministerio de Economia y Competitividad (MINECO), Institute Nacional de Investigacion y Tecnologia Agraria y Alimentaria and European Regional Development Fund (ERDF 2014-2020) (project RTA 2013-00030-C03-02), and by the Universitat Politecnica de Valencia through the FPI grant awarded to Marta de Prados (SP-1.2011-S1-2757).

[EN] Supercritical carbon dioxide inactivation technology represents a promising nonthermal processing method, as it causes minimum impact on the nutritional food properties. The aim of this study was to analyze the combined effect of supercritical carbon dioxide and high-power ultrasound on the inactivation of natural microbiota and the quality attributes of pineapple juice treated in a continuous flow system. Different juice residence times (3.06-4.6min), at 100bar and 31.5?, were used. The results indicated that the microbiota inactivation was complete and the differences obtained in the quality attributes (2.2% for pH, 4.8% for degrees Brix, 2% for vitamin C) were minimal. During storage, microorganisms were not able to recover and the vitamin C decrease could be limited to 8.2% after four weeks. The results demonstrated that the supercritical carbon dioxide-high-power ultrasound technique could be an excellent alternative for the cold pasteurization of pineapple juice., The author(s) disclosed receipt of the following financial support for the research, authorship, and/or publication of this article: This work was supported by the PROMETEOII\2014\005 project financed by the Generalitat Valenciana (Conselleria d'Educacio, Cultura i Esport, Valencia, Spain). The authors acknowledge the Consejo Nacional de Ciencia y Tecnologia (CONACyT) for the scholarship awarded to PhD Student Paniagua-Martinez, I.

[EN] Laboratory continuous regime equipment was designed and built for supercritical CO2 microbial inactivation assisted by high power ultrasound (SC-CO2-HPU). Apple juice, previously inoculated with 1-10x107 CFU/ml of Saccharomyces cerevisiae, was treated in the equipment at different juice residence times (3.06-9.2 min), temperatures (31-41 °C) and pressures (100-300 bars). Inactivation ratios were fitted to a hybrid (boolean-real) model in order to study the effect of the process variables. The maximum inactivation achieved by the system was 7.8 log-cycles. The hybrid model demonstrated that HPU has a significant effect on inactivation after shorter residence times. A multi-objective optimization performed with the hybrid model showed that 6.8 log cycles of inactivation could be obtained after a minimum residence time (3.1 min) with HPU application, whereas under the same conditions but without HPU, the inactivation would be 4.3 log-cycles. Therefore, the ultrasound assisted continuous system has shown a great potential for microbial inactivation using SC-CO2 under mild process conditions., This work was supported by the PROMETEOII\2014\005 project financed by the Generalitat Valenciana (Conselleria d'Educacio, Cultura i Esport, Valencia, Spain). The authors acknowledge the Consejo Nacional de Ciencia y Tecnologia (CONACyT/N. 218273) for the scholarship awarded to PhD Student Paniagua-Martinez, I. The authors especially wish to thank Eng. Ramon Pena for his technical assistance in the development of the equipment.

[EN] Ultrasound can intensify the heating process used to correct texture defects in dry-cured hams. The effect of ultrasound-assisted heating on the proteome of sliced dry-cured ham was evaluated. Dry-cured hams with high proteolysis index (PI > 36) were sliced, vacuum packed and subjected to conventional (CV) and ultrasound-assisted (US) thermal treatments. Comparative proteome profiling between sample groups was assessed by two-dimensional electrophoresis (2-DE) coupled to tandem mass spectrometry. It was found that protein fragmentation increased markedly after US thermal treatment. Specifically, fragments of the major myofibrillar protein, actin, were abundantly over-represented following US heating. In addition, five unfragmented sarcoplasmic proteins (i.e. fatty acid-binding protein, peroxiredoxin-6, superoxide dismutase, carbonyl reductase and aminoacylase) showed increased abundance in the US sample group. These results suggest candidate biomarkers to monitor proteolysis intensity and proteolysis-independent effects linked to cured ham quality by ultrasound application. Significance: The present proteome profiling study of treated dry-cured ham demonstrates the impact of ultrasound action on proteins. Moreover, negative organoleptic effects can be appearing with ultrasound treatment due to proteolysis increase. Therefore, the proteolysis monitoring could help to control these effects. In this regards, our results suggest that actin can be a candidate biomarker to monitor proteolysis intensity., This research was supported by Grant RTA 2013-00030-C03-03 from INIA (Spain). Acknowledgements to INIA for granting Cristina Perez Santaescolastica with a predoctoral scholarship (grant number CPD2015-0212). Jose M. Lorenzo is member of the MARCARNE network, funded by CYTED (ref. 116RT0503).

[EN] The aim of this work was to evaluate the effect of ultrasound on supercritical fluid extraction for the recovery of antioxidants and saponins from agave bagasse as a green extraction technique. When a mass load of 0.086 g/cm(3) was used, ultrasound effect was not observed, due to sample swelling and compaction within the cell. For 0.043 g/cm(3), the intensification effect of ultrasound was significant (p < 0.05) and its magnitude depended on the transducer geometry. For a multiplate transducer geometry, antioxidant capacity increased from 12.18 +/- 1.01 to 20.91 +/- 1.66 mu mol TE/g; and saponins from 19.05 +/- 1.67 to 61.59 +/- 1.99 mu g/g, when ultrasound was applied. Although the amount of bioactives extracted is low, the use of a multiplate transducer design was able to intensify the supercritical fluid extraction of phytochemicals from agave bagasse. Consequently, this type of transducer can become an alternative for the application of ultrasound on the supercritical fluid extraction of other suitable agro-industrial by-products, The authors are grateful for the financial support from CONACYT CVU 270166, Mexico; NutriOmics Chair from Tecnologico de Monterrey, Mexico; and Nutrigenomics Research Chair from Fundacion FEMSA, Mexico. We thank the technical support from the ASPA group technicians and Albino Vargas from AGMEL S.A de C.V for donating agave bagasse for this project

[EN] The impact of low temperattire treatment and its combination with ultrasound has been evaluated in order to correct texture defects in dry-cured hams. A total of 26 dry-cured hams, classified as high proteolysis index (PI > 36%), were used. From these hams, ten slices from each ham sample were cut, vacuum packed and submitted to three different treatments: control (without treatment), conventional thermal treatments (CV) and thermal treatment assisted by power ultrasound (US). The impact of these treatments on instrumental adhesiveness, free amino acid and volatile compounds profile were assessed. Statistical analysis showed that both US and CV treatments, significantly (P, This research was supported by Grant RTA 2013-00030-CO3-03 from INIA (Spain). Acknowledgements to INIA for granting Cristina Perez Santaescolastica with a predoctoral scholarship (grant number CPD2015-0212). Jose M. Lorenzo is member of the MARCARNE network, funded by CYTED (ref. 116RT0503).

[EN] Bearing in mind the highly variable salt content in dry-cured meat products with anatomical integrity, such as pork loin or ham, non-destructive salt content characterization and the online monitoring of dry salting are highly relevant for industrial purposes. This study explores the ability of low-intensity ultrasound to monitor the dry salting of pork Biceps femoris (BF) and Longissimus dorsi (LD) online, as well as to estimate the salt content, both in these muscles and in hams. For this purpose, meat samples were dry salted for up to 16 d at 2 C. During the salting of the muscles, the ultrasonic velocity was continuously measured at time intervals of 5 min, while in the hams it was measured before and after salting. The ultrasonic velocity increased progressively during the salting due to salt gain and water loss, reaching a velocity variation (DV) of 46.8 m/s after 16 d of dry salting for hams and 59.5 and 30.6 m/s after 48 h of dry salting for LD and BF, respectively. Accurate correlations between salt gain and DV were obtained (R2 ¿ 0.903 in LD-BF muscles and R2 ¿ 0.758 in hams), which allowed the assessment of the salt content with an average estimation error of 0.4% w.b. for both muscles and hams. Further research should investigate the use of the time of flight obtained through the pulse-echo mode, instead of the ultrasonic velocity, in order to improve the industrial applicabili, This work was supported by the Spanish Ministerio de Economia y Competitividad (MINECO), Instituto Nacional de Investigacion y Tecnologia Agraria y Alimentaria (INIA) and European Regional Development Fund (ERDF 2014-2020) (contract n. RTA2013-00030-C03-02), by the PROMETEOII\2014\005 and by the Universitat Politecnica de Valencia (UPV) through the FPI grant awarded to Marta de Prados (SP-1.2011-S1-2757).

[EN] The present work was carried out to model the effect of E-beam treatment on the safety,shelf-life and sensory attributes of two poultry products, steaks and hamburgers, and tooptimize the radiation treatment. The inactivation of Salmonella spp. by means of differ-ent irradiation doses was modeled using a first order kinetics. The shelf-life was studiedby periodically counting the bacterial number in samples. For the modeling of experimen-tal data, only the exponential phase of growth was taken into account. The effect of theirradiation dose on the sensory attributes (appearance, odor and flavor) and instrumen-tal color (L*, a* and b* parameters) was modeled using the Gompertz function and theActivation Inactivation or linear models. The optimization of the irradiation dose was car-ried out by maximizing the sensory scores of samples and minimizing the instrumentalcolor changes. The safety and the shelf-life of samples were ensured by introducing con-straints into the optimization problem. In the case of hamburgers, the optimum calculateddose was 2.04 kGy, which guarantees the safety of the product and provides the best combi-nation of sensory and instrumental attributes. As regards the steaks, the optimum assesseddose was 1.11 kGy, significantly lower than for hamburgers, The authors acknowledge the financial support from the Project CSD2007-00016 (CONSOLIDER-INGENIO 2010) and AGL 2010-19158, both funded by the Spanish Ministry of Economy and Competitiveness.

[EN] The effect of high power ultrasound (US) application and pressure on the supercritical fluid extraction (SFE) kinetics of cocoa butter and on characteristics of the extracted cocoa butter (fatty acids composition, transition temperatures, polyphenol content and antioxidant activity) has been evaluated. Extraction experiments were carried out at 40 degrees C and at two pressure levels of 400 bar and 550 bar, without and with US application of 50 +/- 5 W, the extraction yield being significantly improved as the pressure increased and the ultrasound was applied. A Weibull model allowed the accurate simulation of the extraction curves, considering a constant shape factor alpha which was affected only by the US application, whilst the rate constant beta was affected by both pressure and US application. In general, for all cocoa butter samples, the transition temperatures observed corresponded to the polymorph alpha, T-c = 9.9 +/- 0.3 degrees C and T-m = 20.2 +/- 0.4 degrees C. With regard to the fatty acid composition, the stearic (37.8 +/- 0.8%), oleic (33.7 +/- 0.2%), and palmitic (26.0 +/- 0.6%) were the major acids, and none were found to be influenced by either pressure or ultrasound application. Similarly, the total polyphenol content and antioxidant activity were not affected by extraction conditions. The microstructure of cocoa beans after processing was affected by pressure and also by ultrasound application which promoted a breaking of the cell arrangement, facilitating the butter extraction. (C) 2014 Elsevier B.V. All rights reserved., The authors would like to acknowledge the Spanish Government (MICINN), and European Regional Development Fund (FEDER), the European Social Fund (FSE) and the Govern de les Illes Balears for their financial support (DPI2009-14549-C04-02, DPI2012-37466-C03-02, AGL 2012-34627, Project 57/2011).

[EN] The inactivation kinetics of Escherichia coli (E. coli) and Saccharomyces cerevisiae (S. cerevisiae) cells in apple juice subjected to supercritical carbon dioxide (SC-CO2) assisted by high power ultrasound (HPU) at different pressures (100 350 bar, 36 °C) and temperatures (31 41 °C, 225 bar) were studied. On average, shorter process times were required to achieve the total inactivation of S. cerevisiae (2 6 min) in apple juice than E. coli (7 min). The inactivation kinetics of E. coli and S. cerevisiae were satisfactorily described by the Peleg Type A and theWeibull model, respectively, considering temperature and pressure as model parameters. Transmission electron microscopy (TEM) and light microscopy (LM) techniques were used to study the cellular changes of SC-CO2 (350 bar, 36 °C, 5 min) and SC-CO2+HPU (350 bar, 36 °C, 5 min, 40W)treated cells. TEMand LMimages revealed that 5 min of SC-CO2 treatment generated minor morphological modifications, although no inactivation of the cells was obtained. However, 5 min of SC-CO2+HPU treatment totally inactivated the population of both microorganisms. SC-CO2 + HPU produced the degradation of the internal cell content and the disruption of the cell wall and plasmalemma, which prevented the possible regrowth of the cells during refrigerated storage., The authors acknowledge the financial support from project CSD2007-00016 (CONSOLIDER-INGENIO 2010, Spanish Ministry of Science and Innovation) and from project PROMETEO/2010/062; Generalitat Valenciana. We thank Dr. Emilia Matallana and Dr. Paula Alepuz for the generous gift of S. cerevisiae T73 and E. coli DH1 strains, respectively.

The authors acknowledge the financial support from the "Ministerio de Economia y Competitividad" in Spain (Project RTA 2010-00029-C04-02).

[EN] In this work, the feasibility of using non-contact ultrasonic techniques (air-coupled and scanning acoustic microscopy, SAM) for characterizing different dry-cured meat products was assessed. Air-coupled ultrasonic measurements were performed on vacuum packaged sliced dry-cured ham, and compared with contact measurements. The average ultrasonic velocity in dry-cured ham was 1846 +/- 49 m/s and 1842 +/- 42 m/s for air-coupled and contact measurements, respectively. The deviation (1% relative error) between both techniques was related to the influence of the heterogeneous structure and composition of dry-cured ham and the transducer focusing. The SAM was used to characterize dry-cured ham and chorizo samples. B-scan images for dry-cured ham and chorizo showed two dominant reflections from the sample, linked to reflections in the lean and fatty tissues. The results indicate that contact ultrasonic measurements could be replaced by the air-coupled technique, reducing the measuring time and the material handling. On the other hand, SAM technique allows the microscopic characterization of dry-cured meat products. (C) 2013 Elsevier Ltd. All rights reserved., The authors acknowledge the financial support from the "Ministerio de Economia y Competitividad" in Spain through the Projects RTA 2010-00029-C04-02 and DPI2011-22438.

[EN] Ultrasonic velocity was used to characterise the differences in composition and texture of Biceps Femoris muscles from four batches of pigs of different genetics (Iberian and Iberian x Duroc) and feeding systems ("montanera" and concentrate). Significant differences (p, The authors acknowledge financial support from the "Ministerio de Educacion y Ciencia" in Spain (Projects RTA 2010-00029-004-02: CONSOLIDER - Ingenio 2010: CARNISENUSA (CSD2007-00016)) and the valuable advice of Professor Jesus Ventanas.

In order to find the relationships among variables affecting the resistance of salmonella to the thermosonication treatment, the combined effect of simultaneously applied ultrasonic waves and heat treatment on the survival of a strain of Salmonella enterica serovar Enteritidis was studied in several volumes (100, 200, 500, 750 and 1200 mL) of distilled water. The higher the liquid volume, the greater the decimal reduction times ( D R ). The joint confidence regions for D R and z were calculated showing significant ( p R 2 = 0.95). This model allows the effect of sonication to be predicted under different process conditions and, therefore, is useful for the scale-up of the system.

The density, heat capacity and thermal conductivity of mango pulp (Mangifera indica L. cv. Tommy Atkins) were determined at moisture contents of between 0.9 and 0.52 kg kg−1 (w.b.) and temperatures of between 20 and 80 °C. The experimental data were satisfactorily fitted (explained variation values >99.1%) as functions of the moisture content and temperature by using multivariate linear models. In the range of conditions considered, the moisture content exhibits a greater influence on the studied properties than temperature.

The use of two different non-destructive impact techniques for cheese texture assessment was evaluated. The textural properties measured using a texture analyzer increased linearly throughout curing time showing a characteristic pattern that was also found for the impact parameters. A good relationship was found between the textural parameters and the impact force–deformation and acoustic impulse–response ones. The best correlation coefficient corresponded to the relationship between the maximum impact force (MIF) and the maximum force (MF) for the spherical probes used in the textural analysis (avg. R = 0.965). The energy content of the 70–400 Hz frequency spectrum also allowed for an accurate prediction of the textural parameters like MF ( R = 0.844). Multiple regression significantly improved the assessment of all the textural parameters using the non-destructive impact measurements. Consequently, non-destructive impact tests could be used to predict Manchego cheese texture. These systems are inexpensive, very fast and could be installed on-line.

Power ultrasound application could constitute a way to enhance food drying in order to improve not only mass transfer but also product quality, since it does not significantly heat the material. The main aim of this work was to assess the influence of power ultrasound on the mass transfer process during drying of different products, carrot, persimmon and lemon peel. Convective drying kinetics were carried out with ultrasound (US experiments 21.8 kHz, 75 W), or without ultrasound application (AIR experiments) at air velocities ranging between 0.5–12 m s −1 . Different geometries were used for each of the products: cubes in carrots (2 L = 8.5 mm), cylinders in persimmon (2 L = 30 mm and 2 R = 13 mm) and slabs in lemon peel (L = 10 mm). Drying kinetics were modelled by considering different diffusion models according to the geometry. The results show that air velocity and raw material characteristics play a role in convective drying kinetics assisted by power ultrasound. Power ultrasound increased effective moisture diffusivity at low air velocities for all the products. However, in the case of lemon peel, ultrasound also improved the drying rate at high air velocities. This behaviour may be explained by the disruption of the acoustic field at high air flow rates and the different level of intensity required due to the structure of the products. Therefore, the raw material constitutes an important variable to establish the influence of power ultrasound on convective drying.