Search

Introduction: Pedicle screw loosening is a major problem in spine surgery. Computed tomography (CT) is the gold standard to diagnose screw loosening. Disadvantages of CT include low sensitivity and specificity for the detection of loosened screws as well as the need for radiation exposure. The aim of this study was to provide a proof of concept of a novel, non-invasive, inductive sensing device for transcutaneous detection of screw loosening using a pulse induction metal detector. Materials/Methods: Two fresh frozen human cadavers were initially instrumented in the lumbar spinal region (L1 to L5). After assessment of the sensing device behavior using a wooden beam and 3D printed place holders of predefined distances, the ability of implant detection and screw stability determination were assessed during two experiments. Pedicle screw loosening was induced using 3D printed drill/loosening guides during the instrumentation of the lumbar spine. Screw stability was determined by applying weight to the spinous processes of interest and measuring the relative movement of the pedicle screw using the inductive sensor coil. Results: The sensitivity of our detection coil for an implant movement measurement showed to be high at close distances (60mV voltage change per mm movement), with signal amplitude vanishing at sensing distances of 50mm or greater. Signal amplitude significantly (p < .05) differed with the number of instrumented levels. When differentiating between instrumentation with and without loosened screws, significant (p < .05) mean differences were found in half of all comparative cases. All these differences were smaller than the predefined signal voltage threshold of (60 mV/mm). Discussion/Conclusion: In this study, the feasibility of a new, inductive and non-invasive sensor concept was tested. While the basic principle of the approach is promising, our implementation was not successful in demonstrating sufficient sensitivity for the required detectability. It appears conceivable that the concept can be successfully implemented with more sensitive sensors and more complex evaluation methods.

Graphical Abstract

Background: Spinal fusion is the most common surgical treatment for the management of degenerative spinal disease. However, complications such as screw loosening lead to painful pseudoarthrosis, and are a common reason for revision. Optimization of screw trajectories to increase implant resistance to mechanical loading is essential. A recent optimization method has shown potential for determining optimal screw position and size based on areas of high bone elastic modulus (E-modulus).Aim: The aim of this biomechanical study was to verify the optimization algorithm for pedicle screw placement in a cadaveric study and to quantify the effect of optimization. The pull-out strength of pedicle screws with an optimized trajectory was compared to that of a traditional trajectory.Methods: Twenty-five lumbar vertebrae were instrumented with pedicle screws (on one side, the pedicle screws were inserted in the traditional way, on the other side, the screws were inserted using an optimized trajectory).Results: An improvement in pull-out strength and pull-out strain energy of the optimized screw trajectory compared to the traditional screw trajectory was only observed for E-modulus values greater than 3500 MPa cm3. For values of 3500 MPa cm3 or less, optimization showed no clear benefit. The median screw length of the optimized pedicle screws was significantly smaller than the median screw length of the traditionally inserted pedicle screws, p < 0.001.Discussion: Optimization of the pedicle screw trajectory is feasible, but seems to apply only to vertebrae with very high E-modulus values. This is likely because screw trajectory optimization resulted in a reduction in screw length and therefore a reduction in the implant-bone interface. Future efforts to predict the optimal pedicle screw trajectory should include screw length as a critical component of potential stability.

Abstract Posterior screw-rod constructs can be used to stabilize spinal segments; however, the stiffness is not absolute, and some motion can persist. While the effect of crosslink-augmentation has been evaluated in multiple studies, the fundamental explanation of their effectiveness has not been investigated. The aim of this study was to quantify the parameters “screw rotation” and “parallelogram deformation” in posterior instrumentations with and without crosslinks to analyze and explain their fundamental effect. Biomechanical testing of 15 posteriorly instrumented human spinal segments (Th10/11—L4/L5) was conducted in axial rotation, lateral bending, and flexion–extension with ± 7.5 Nm. Screw rotation and parallelogram deformation were compared for both configurations. Parallelogram deformation occurred predominantly during axial rotation (2.6°) and was reduced by 60% (−1.45°, p = 0.02) by the addition of a crosslink. Simultaneously, screw rotation (0.56°) was reduced by 48% (−0.27°, p = 0.02) in this loading condition. During lateral bending, 0.38° of parallelogram deformation and 1.44° of screw rotation was measured and no significant reduction was achieved by crosslink-augmentation (8%, −0.03°, −p = 0.3 and −13%, −0.19°, p = 0.7 respectively). During flexion–extension, parallelogram deformation was 0.4° and screw rotation was 0.39° and crosslink-augmentation had no significant effect on these values (−0.12°, −30%, p = 0.5 and −0°, −0%, p = 0.8 respectively). In axial rotation, crosslink-augmentation can reduce parallelogram deformation and with that, screw rotation. In lateral bending and flexion–extension parallelogram deformation is minimal and crosslink-augmentation has no significant effect. Since the relatively large screw rotation in lateral bending is not caused by parallelogram deformation, crosslink-augmentation is no adequate countermeasure. The fundamental understanding of the biomechanical effect of crosslink-augmentation helps better understand its potential and limitations in increasing construct stiffness.

Abstract Background Vertebral endplate signal intensity changes visualized by magnetic resonance imaging termed Modic changes (MC) are highly prevalent in low back pain patients. Interconvertibility between the three MC subtypes (MC1, MC2, MC3) suggests different pathological stages. Histologically, granulation tissue, fibrosis, and bone marrow edema are signs of inflammation in MC1 and MC2. However, different inflammatory infiltrates and amount of fatty marrow suggest distinct inflammatory processes in MC2. Aims The aims of this study were to investigate (i) the degree of bony (BEP) and cartilage endplate (CEP) degeneration in MC2, (ii) to identify inflammatory MC2 pathomechanisms, and (iii) to show that these marrow changes correlate with severity of endplate degeneration. Methods Pairs of axial biopsies (n = 58) spanning the entire vertebral body including both CEPs were collected from human cadaveric vertebrae with MC2. From one biopsy, the bone marrow directly adjacent to the CEP was analyzed with mass spectrometry. Differentially expressed proteins (DEPs) between MC2 and control were identified and bioinformatic enrichment analysis was performed. The other biopsy was processed for paraffin histology and BEP/CEP degenerations were scored. Endplate scores were correlated with DEPs. Results Endplates from MC2 were significantly more degenerated. Proteomic analysis revealed an activated complement system, increased expression of extracellular matrix proteins, angiogenic, and neurogenic factors in MC2 marrow. Endplate scores correlated with upregulated complement and neurogenic proteins. Discussion The inflammatory pathomechanisms in MC2 comprises activation of the complement system. Concurrent inflammation, fibrosis, angiogenesis, and neurogenesis indicate that MC2 is a chronic inflammation. Correlation of endplate damage with complement and neurogenic proteins suggest that complement system activation and neoinnervation may be linked to endplate damage. The endplate‐near marrow is the pathomechanistic site, because MC2 occur at locations with more endplate degeneration. Conclusion MC2 are fibroinflammatory changes with complement system involvement which occur adjacent to damaged endplates.

Intervertebral discs are microstructurally complex spinal tissues that add greatly to the flexibility and mechanical strength of the human spine. Attempting to provide an adjustable basis for capturing a wide range of mechanical characteristics and to better address known challenges of numerical modeling of the disc, we present a robust finite-element-based model formulation for spinal segments in a hyperelastic framework using tetrahedral elements. We evaluate the model stability and accuracy using numerical simulations, with particular attention to the degenerated intervertebral discs and their likely skewed and narrowed geometry. To this end, 1) annulus fibrosus is modeled as a fiber-reinforced Mooney-Rivlin type solid for numerical analysis. 2) An adaptive state-variable dependent explicit time step is proposed and utilized here as a computationally efficient alternative to theoretical estimates. 3) Tetrahedral-element-based FE models for spinal segments under various loading conditions are evaluated for their use in robust numerical simulations. For flexion, extension, lateral bending, and axial rotation load cases, numerical simulations reveal that a suitable framework based on tetrahedral elements can provide greater stability and flexibility concerning geometrical meshing over commonly employed hexahedral-element-based ones for representation and study of spinal segments in various stages of degeneration.

How does Digital Mappa, a browser-based annotation tool, fit into the current landscape of Virtual Research Environments? How is an intuitive WYSIWYG graphical user interface suited for simple (scholarly) editions and image-text representations? What about involving different users via crowdsourcing? For this review, we took three distinct perspectives (user, teacher, and backend admin) and tested the tool for text annotation but furthermore for linking images with text. Digital Mappa proves to be a stable, not-so-easy-to-set-up tool that covers a lot of ground concerning annotation and image linking. Subsuming, we describe a mature system that allows for easy editing, suitable in the classroom. Critically, it has been assessed that the tool refrains from standards (such as TEI XML) and lacks capabilities to involve larger groups (e.g. for crowdsourcing).

Introduction: Sufficient screw hold is an indispensable requirement for successful spinal fusion, but pedicle screw loosening is a highly prevalent burden. The aim of this study was to quantify the contribution of the pedicle and corpus region in relation to bone quality and loading amplitude of pedicle screws with traditional trajectories.Methods: After CT examination to classify bone quality, 14 pedicle screws were inserted into seven L5. Subsequently, Micro-CT images were acquired to analyze the screw’s location and the vertebrae were split in the midsagittal plane and horizontally along the screw’s axis to allow imprint tests with 6 mm long sections of the pedicle screws in a caudal direction perpendicular to the screw’s surface. Force-displacement curves in combination with the micro-CT data were used to reconstruct the resistance of the pedicle and corpus region at different loading amplitudes.Results: Bone quality was classified as normal in three specimens, as moderate in two and as bad in two specimens, resulting in six, four, and four pedicle screws per group. The screw length in the pedicle region in relation to the inserted screw length was measured at an average of 63%, 62%, and 52% for the three groups, respectively. At a calculated 100 N axial load acting on the whole pedicle screw, the pedicle region contributed an average of 55%, 58%, and 58% resistance for the normal, moderate, and bad bone quality specimens, respectively. With 500 N load, these values were measured at 59%, 63%, and 73% and with 1000 N load, they were quantified at 71%, 75%, and 81%.Conclusion: At lower loading amplitudes, the contribution of the pedicle and corpus region on pedicle screw hold are largely balanced and independent of bone quality. With increasing loading amplitudes, the contribution of the pedicle region increases disproportionally, and this increase is even more pronounced in situations with reduced bone quality. These results demonstrate the importance of the pedicle region for screw hold, especially for reduced bone quality.

Abstract Background Anterior scoliosis correction is a powerful technique with the disadvantage of a kyphotic effect on lumbar and thoracolumbar curves. We aimed to investigate whether a cognizant interposition of a rib graft anteriorly and at the concave side of the scoliotic curve causes significant fulcrum effect to enforce scoliosis correction and to reduce interfusional kyphosis in anterior scoliosis corrections. Methods Twenty otherwise comparable patients with lumbar and thoracolumbar adolescent idiopathic scoliosis (AIS) curves undergoing anterior short scoliosis correction with (n = 10) or without (n = 10, matched for age, gender and degree of deformity) fulcrum effect were retrospectively compared by means of radiographic measurements (sagittal and coronal profile, Cobb angles and intersegmental deformity correction angles) to evaluate the effect of this modified surgical technique. Results The overall amount of scoliosis correction was similar with 74 and 60% of initial curves of 57° and 53° in the case and control group respectively with a mean of 3 fused segments (4 screws). Statistically relevant differences were found for intersegmental coronal cobb angles at the apex of 20° to 3° and 17° to 9° with and without fulcrum, respectively (p

Background: Planning of surgical procedures for spinal fusion is performed on standing radiographs, neglecting the fact that patients are mostly in the sitting position during daily life. The awareness about the differences in the standing and sitting configuration of the spine has increased during the last years. The purpose was to provide an overview of studies related to seated imaging for spinal fusion surgery, identify knowledge gaps and evaluate future research questions. Methods: A literature search according to the Preferred Reporting Items for Systematic Reviews and Meta-Analysis (PRISMA) extension for Scoping Reviews (PRISMASc) was performed to identify reports related to seated imaging for spinal deformity surgery. A summary of the finding is presented for healthy individuals as well as patients with a spinal disorder and/or surgery. Results: The systematic search identified 30 original studies reporting on 1) the pre- and postoperative use of seated imaging of the spine (n=12), 2) seated imaging of the spine for non – surgical evaluation (n=7) and 3) seated imaging of the spine among healthy individuals (12). The summarized evidence illuminates that sitting leads to a straightening of the spine decreasing thoracic kyphosis (TK), lumbar lordosis (LL), the sacral slope (SS). Further, the postural change between standing and sitting is more significant on the lower segments of the spine. Also, the adjacent segment compensates the needed postural change of the lumbar spine while sitting with hyperkyphosis. Conclusions: The spine has a different configuration in standing and sitting. This systematic review summarizes the current knowledge about such differences and reveals that there is minimal evidence about their consideration for surgical planning of spinal fusion surgery. Further, it identifies gaps in knowledge and areas of further research.

Background: This work evaluates the feasibility, development, and validation of a machine learning pipeline that includes all tasks from MRI input to the segmentation and grading of the intervertebral discs in the lumbar spine, offering multiple different radiological gradings of degeneration as quantitative objective output. Methods: The pipelines’ performance was analysed on 1′000 T2-weighted sagittal MRI. Binary outputs were assessed with the harmonic mean of precision and recall (DSC) and the area under the precision-recall curve (AUC-PR). Multi-class output scores were averaged and complemented by the Top-2 categorical accuracy. The processing success rate was evaluated on 10′053 unlabelled MRI scans of lumbar spines. Results: The midsagittal plane selection achieved an DSC of 74,80% ± 2,99% and an AUC-PR score of 81.71% ± 2.72% (96.91% Top-2 categorical accuracy). The segmentation network obtained a DSC of 91.80% ± 0.44%. The Pfirrmann grading of intervertebral discs in the midsagittal plane was classified with a DSC of 64.08% ± 3.29% and an AUC-PR score of 68.25% ± 6.00% (91.65% Top-2 categorical accuracy). Disc herniations achieved a DSC of 61.57% ± 3.39% and an AUC-PR score of 66.86% ± 5.03%. The cranial endplate defects reached a DSC of 49.76% ± 3.45% and 52.36% ± 1.98% AUC-PR (slightly superior predictions of caudal endplate defect). The binary classifications for the caudal Schmorl's nodes obtained a DSC of 91.58% ± 2.25% with an AUC-PR metric of 96.69% ± 1.58% (similar performance for cranial Schmorl's nodes). Spondylolisthesis was classified with a DSC of 89.03% ± 2.42% and an AUC-PR score of 95.98% ± 1.82%. Annular Fissures were predicted with a DSC of 78.09% ± 7.21% and an AUC-PR score of 86.31% ± 7.45%. Intervertebral disc classifications in the parasagittal plane achieved an equivalent performance. The pipeline successfully processed 98.53% of the provided sagittal MRI scans. Conclusions: The present deep learning framework has the potential to aid the quantitative evaluation of spinal MRI for an array of clinically established grading systems.

Background: Posterior lumbar instrumentation requires sufficient primary stiffness to ensure bony fusion and to avoid pseudarthrosis, screw loosening, or implant failure. To enhance primary construct stiffness, transverse cross-link (CL) connectors attached to the vertical rods can be used. Their effect on the stability of a spinal instrumentation with simultaneous decompression is yet not clear. This study aimed to evaluate the impact of CL augmentation on single-level lumbar instrumentation stiffness after gradual decompression procedures. Methods: Seventeen vertebral segments (6 L1/2, 6 L3/4, 5 L5/S1) of 12 fresh-frozen human cadavers were instrumented with a transpedicular screw–rod construct following the traditional pedicle screw trajectory. Range of motion (ROM) of the segments was sequentially recorded before and after four procedures: (A) instrumented before decompression, (B) instrumented after unilateral laminotomy, (C) instrumented after midline bilateral laminotomy, and (D) instrumented after unilateral facetectomy (with transforaminal lumbar interbody fusion [TLIF]). Each test was performed with and without CL augmentation. The motion between the cranial and caudal vertebrae was evaluated in all six major loading directions: flexion/extension (FE), lateral bending (LB), lateral shear (LS), anterior shear (AS), axial rotation (AR), and axial compression/distraction (AC). Results: ROM was significantly reduced with CL augmentation in AR by Δ0.03–0.18° (7–12%) with a significantly higher ROM reduction after more extensive decompression. Furthermore, slight reductions in FE and LB were observed; these reached statistical significance for FE after facetectomy and TLIF insertion only (Δ0.15; 3%). The instrumentation levels did not reveal any subgroup differences. Conclusion: CL augmentation reduces AR-ROM by 7–12% in single-level instrumentation of the lumbar spine, with the effect increasing along with the extensiveness of the decompression technique. In light of the discrete absolute changes, CL augmentation may be warranted for highly unstable vertebral segments rather than for standard single-level posterior spinal fusion and decompression.

Musculoskeletal modeling is a well-established method in spine biomechanics and generally employed for investigations concerning both the healthy and the pathological spine. It commonly involves inverse kinematics and optimization of muscle activity and provides detailed insight into joint loading. The aim of the present work was to develop and validate a procedure for the automatized generation of semi-subject-specific multi-rigid body models with an articulated lumbar spine. Individualization of the models was achieved with a novel approach incorporating information from annotated EOS images. The size and alignment of bony structures, as well as specific body weight distribution along the spine segments, were accurately reproduced in the 3D models. To ensure the pipeline’s robustness, models based on 145 EOS images of subjects with various weight distributions and spinopelvic parameters were generated. For validation, we performed kinematics-dependent and segment-dependent comparisons of the average joint loads obtained for our cohort with the outcome of various published in vivo and in situ studies. Overall, our results agreed well with literature data. The here described method is a promising tool for studying a variety of clinical questions, ranging from the evaluation of the effects of alignment variation on joint loading to the assessment of possible pathomechanisms involved in adjacent segment disease.

The cortical bone trajectory (CBT) has been introduced with the aim of better screw hold, however, screw-rod constructs with this trajectory might provide less rigidity in lateral bending (LB) and axial rotation (AR) compared to the constructs with the traditional trajectory (TT). Therefore, the addition of a horizontal cross-connector could be beneficial in counteracting this possible inferiority. The aim of this study was to compare the primary rigidity of TT with CBT screw-rod constructs and to quantify the effect of cross-connector-augmentation in both. Spines of four human cadavers (T9 -L5) were cropped into 15 functional spine units (FSU). Eight FSUs were instrumented with TT and seven FSUs with CBT pedicle screws. The segments were tested in six loading directions in three configurations: uninstrumented, instrumented with and without cross-connector. The motion between the cranial and caudal vertebra was recorded. The range of motion (ROM) between the CBT and the TT group did not differ significantly in either configuration. Cross-connector -augmentation did reduce the ROM in AR (16.3%, 0.27°, p = 0.02), LB (2.9%, 0.07°, p = 0.03) and flexion-extension FE (2.3%, 0.04°, p = 0.02) for the TT group and in AR (20.6%, 0.31°, p = 0.01) for the CBT-group. The primary rigidity of TT and CBT single level screw-rod constructs did not show significant difference. The minimal reduction of ROM due to cross-connector-augmentation seems clinically not relevant. Based on the findings of these study there is no increased necessity to use a cross-connector in a CBT-construct.

The surgical standard of care for lumbar discectomy leaves the annulus fibrosus (AF) defect unrepaired, despite considerable risk for a recurrent herniation. Identification of a viable defect repair strategy has until now been elusive. The scope of this ex vivo biomechanical study was to evaluate crosslinking hydrogels as potentially promising AF defect sealants, and provide a baseline for their use in combination with collagen scaffolds that restore disc volume. This study directly compared genipin crosslinked fibrin hydrogel (FibGen) as a promising preclinical candidate against a clinically available adhesive composed of glutaraldehyde and albumin (BioGlue). Forty-two bovine coccygeal functional spine units (FSU) were randomly allocated into four groups, namely untreated (control, n = 12), repaired with either one of the tested hydrogels (BioGlue, n = 12; FibGen, n = 12), or FibGen used in combination with a collagen hydrogel scaffold (FibGen+Scaffold, n = 6). All specimens underwent a moderate mechanical testing protocol in intact, injured and repaired states. After completion of the moderate testing protocol, the samples underwent a ramp-to-failure test. Lumbar discectomy destabilized the FSU as quantified by increased torsional range of motion (28.0° (19.1, 45.1) vs. 41.39° (27.3, 84.9), p