Search

Abstract In the development of structural composites based on regenerated cellulose filaments, the physical and chemical interactions at the fibre-matrix interphase need to be fully understood. In the present study, continuous yarns and filaments of viscose (rayon) were treated with either polymeric diphenylmethane diisocyanate (pMDI) or a pMDI-based hardener for polyurethane resins. The effect of isocyanate treatment on mechanical yarn properties was evaluated in tensile tests. A significant decrease in tensile modulus, tensile force and elongation at break was found for treated samples. As revealed by size exclusion chromatography, isocyanate treatment resulted in a significantly reduced molecular weight of cellulose, presumably owing to hydrolytic cleavage caused by hydrochloric acid occurring as an impurity in pMDI. Yarn twist, fibre moisture content and, most significantly, the chemical composition of the isocyanate matrix were identified as critical process parameters strongly affecting the extent of reduction in mechanical performance. To cope with the problem of degradative reactions an additional step using calcium carbonate to trap hydrogen ions is proposed.

Summary Due to the rising global environment protection awareness, recycling strategies that comply with the circular economy principles are needed. Polyesters are among the most used materials in the textile industry; therefore, achieving a complete poly(ethylene terephthalate) (PET) hydrolysis in an environmentally friendly way is a current challenge. In this work, a chemo‐enzymatic treatment was developed to recover the PET building blocks, namely terephthalic acid (TA) and ethylene glycol. To monitor the monomer and oligomer content in solid samples, a Fourier‐transformed Raman method was successfully developed. A shift of the free carboxylic groups (1632 cm−1) of TA into the deprotonated state (1604 and 1398 cm−1) was observed and bands at 1728 and 1398 cm−1 were used to assess purity of TA after the chemo‐enzymatic PET hydrolysis. The chemical treatment, performed under neutral conditions (T = 250 °C, P = 40 bar), led to conversion of PET into 85% TA and small oligomers. The latter were hydrolysed in a second step using the Humicola insolens cutinase (HiC) yielding 97% pure TA, therefore comparable with the commercial synthesis‐grade TA (98%).

Actual polymer bioresorbable stents (BRS) generate a risk of device thrombosis as a consequence of the incomplete endothelialization after stent implantation. The material-tissue interactions are not fully controlled and stent fabrication techniques do not allow personalized medical solutions. This work investigates the effect of different functionalization strategies onto solvent-cast poly(l-lactic acid) (PLLA) surfaces with the capacity to enhance surface endothelial adhesion and the fabrication of 3D printed BRS. PLLA films were obtained by solvent casting and treated thermally to increase mechanical properties. Surface functionalization was performed by oxygen plasma (OP), sodium hydroxide (SH) etching, or cutinase enzyme (ET) hydrolysis, generating hydroxyl and carboxyl groups. A higher amount of carboxyl and hydroxyl groups was determined on OP and ET compared to the SH surfaces, as determined by contact angle and X-ray photoelectron spectroscopy (XPS). Endothelial cells (ECs) adhesion and spreading was higher on OP and ET functionalized surfaces correlated with the increase of functional groups without affecting the degradation. To verify the feasibility of the approach proposed, 3D printed PLLA BRS stents were produced by the solvent-cast direct writing technique.

To study hydrolysis of aromatic and aliphatic polyesters cutinase 1 from Thermobifida cellulosilytica (Thc_Cut1) was expressed in P. pastoris. No significant differences between the expression of native Thc_Cut1 and of two glycosylation site knock out mutants (Thc_Cut1_koAsn and Thc_Cut1_koST) concerning the total extracellular protein concentration and volumetric activity were observed. Hydrolysis of poly(ethylene terephthalate) (PET) was shown for all three enzymes based on quantification of released products by HPLC and similar concentrations of released terephthalic acid (TPA) and mono(2-hydroxyethyl) terephthalate (MHET) were detected for all enzymes. Both tested aliphatic polyesters poly(butylene succinate) (PBS) and poly(3-hydroxybutyrate-co-3-hydroxyvalerate) (PHBV) were hydrolyzed by Thc_Cut1 and Thc_Cut1_koST, although PBS was hydrolyzed to significantly higher extent than PHBV. These findings were also confirmed via quartz crystal microbalance (QCM) analysis; for PHBV only a small mass change was observed while the mass of PBS thin films decreased by 93% upon enzymatic hydrolysis with Thc_Cut1. Although both enzymes led to similar concentrations of released products upon hydrolysis of PET and PHBV, Thc_Cut1_koST was found to be significantly more active on PBS than the native Thc_Cut1. Hydrolysis of PBS films by Thc_Cut1 and Thc_Cut1_koST was followed by weight loss and scanning electron microscopy (SEM). Within 96 h of hydrolysis up to 92 and 41% of weight loss were detected with Thc_Cut1_koST and Thc_Cut1, respectively. Furthermore, SEM characterization of PBS films clearly showed that enzyme tretment resulted in morphological changes of the film surface.

In this study cutinases from Thermobifida cellulosilyticaDSM44535 (Thc_Cut1 and Thc_Cut2) and Thermobifida fuscaDSM44342 (Thf42_Cut1) hydrolyzing poly(ethylene terephthalate) (PET) were successfully cloned and expressed in E.coliBL21-Gold(DE3). Their ability to hydrolyze PET was compared with other enzymes hydrolyzing natural polyesters, including the PHA depolymerase (ePhaZmcl) from Pseudomonas fluorescensand two cutinases from T. fuscaKW3. The three isolated Thermobifidacutinases are very similar (only a maximum of 18 amino acid differences) but yet had different kinetic parameters on soluble substrates. Their kcatand Kmvalues on pNP–acetate were in the ranges 2.4–211.9 s–1and 127–200 μM while on pNP–butyrate they showed kcatand Kmvalues between 5.3 and 195.1 s–1and between 1483 and 2133 μM. Thc_Cut1 released highest amounts of MHET and terephthalic acid from PET and bis(benzoyloxyethyl) terephthalate (3PET) with the highest concomitant increase in PET hydrophilicity as indicated by water contact angle (WCA) decreases. FTIR-ATR analysis revealed an increase in the crystallinity index A1340/A1410upon enzyme treatment and an increase of the amount of carboxylic and hydroxylic was measured using derivatization with 2-(bromomethyl)naphthalene. Modeling the covalently bound tetrahedral intermediate consisting of cutinase and 3PET indicated that the active site His-209 is in the proximity of the O of the substrate thus allowing hydrolysis. On the other hand, the models indicated that regions of Thc_Cut1 and Thc_Cut2 which differed in electrostatic and in hydrophobic surface properties were able to reach/interact with PET which may explain their different hydrolysis efficiencies. [ABSTRACT FROM AUTHOR]

The present study investigated the effect of selected structural parameters on the mechanical performance of regenerated cellulose composites. The experimental setup comprised continuous viscose (rayon) yarns embedded in a matrix of epoxy resin. Mechanical and microscopic characterizations involved comparing the following: yarns consisting of untwisted filaments and twisted warp and weft yarns taken from a plain weave fabric, yarns with and without avivage (fiber finish), as well as yarns with and without an acrylic coating. During the epoxy treatment, samples were either prestressed or laid horizontally to preserve the original yarn structure. Tensile tests revealed that yarn crimp had a significant impact on the strength properties of composite specimens, a higher crimp ratio leading to a decrease in performance. Applying prestress to crimped yarns has proven to be an effective way to enable straight alignment in the loading direction, which is essential for the design of stiffness‐ and strength‐optimized yarn composites. Unlike an avivage, which did not markedly affect the mechanical properties of composite yarns, the application of an acrylic coating prior to resin impregnation was found to provide significantly increased extensibility and more ductile fracture behavior. [ABSTRACT FROM AUTHOR]

Actual polymer bioresorbable stents (BRS) generate a risk of device thrombosis as a consequence of the incomplete endothelialization after stent implantation. The material-tissue interactions are not fully controlled and stent fabrication techniques do not allow personalized medical solutions. This work investigates the effect of different functionalization strategies onto solvent-cast poly(l-lactic acid) (PLLA) surfaces with the capacity to enhance surface endothelial adhesion and the fabrication of 3D printed BRS. PLLA films were obtained by solvent casting and treated thermally to increase mechanical properties. Surface functionalization was performed by oxygen plasma (OP), sodium hydroxide (SH) etching, or cutinase enzyme (ET) hydrolysis, generating hydroxyl and carboxyl groups. A higher amount of carboxyl and hydroxyl groups was determined on OP and ET compared to the SH surfaces, as determined by contact angle and X-ray photoelectron spectroscopy (XPS). Endothelial cells (ECs) adhesion and spreading was higher on OP and ET functionalized surfaces correlated with the increase of functional groups without affecting the degradation. To verify the feasibility of the approach proposed, 3D printed PLLA BRS stents were produced by the solvent-cast direct writing technique. [ABSTRACT FROM AUTHOR]

Certain members of the carboxylesterase superfamily can act at the interface between water and water-insoluble substrates. However, nonnatural bulky polyesters usually are not efficiently hydrolyzed. In the recent years, the potential of enzyme engineering to improve hydrolysis of synthetic polyesters has been demonstrated. Regions on the enzyme surface have been modified by using site-directed mutagenesis in order to tune sorption processes through increased hydrophobicity of the enzyme surface. Such modifications can involve specific amino acid substitutions, addition of binding modules, or truncation of entire domains improving sorption properties and/or dynamics of the enzyme. In this review, we provide a comprehensive overview on different strategies developed in the recent years for enzyme surface engineering to improve the activity of polyester-hydrolyzing enzymes. [ABSTRACT FROM AUTHOR]

Due to the rising global environment protection awareness, recycling strategies that comply with the circular economy principles are needed. Polyesters are among the most used materials in the textile industry; therefore, achieving a complete poly(ethylene terephthalate) ( PET) hydrolysis in an environmentally friendly way is a current challenge. In this work, a chemo-enzymatic treatment was developed to recover the PET building blocks, namely terephthalic acid ( TA) and ethylene glycol. To monitor the monomer and oligomer content in solid samples, a Fourier-transformed Raman method was successfully developed. A shift of the free carboxylic groups (1632 cm−1) of TA into the deprotonated state (1604 and 1398 cm−1) was observed and bands at 1728 and 1398 cm−1 were used to assess purity of TA after the chemo-enzymatic PET hydrolysis. The chemical treatment, performed under neutral conditions (T = 250 °C, P = 40 bar), led to conversion of PET into 85% TA and small oligomers. The latter were hydrolysed in a second step using the Humicola insolens cutinase (HiC) yielding 97% pure TA, therefore comparable with the commercial synthesis-grade TA (98%). [ABSTRACT FROM AUTHOR]

ABSTRACT We have investigated the structures of two native cutinases from Thermobifida cellulosilytica, namely Thc_Cut1 and Thc_Cut2 as well as of two variants, Thc_Cut2_DM (Thc_Cut2_ Arg29Asn_Ala30Val) and Thc_Cut2_TM (Thc_Cut2_Arg19Ser_Arg29Asn_Ala30Val). The four enzymes showed different activities towards the aliphatic polyester poly(lactic acid) (PLLA). The crystal structures of the four enzymes were successfully solved and in combination with Small Angle X-Ray Scattering (SAXS) the structural features responsible for the selectivity difference were elucidated. Analysis of the crystal structures did not indicate significant conformational differences among the different cutinases. However, the distinctive SAXS scattering data collected from the enzymes in solution indicated a remarkable surface charge difference. The difference in the electrostatic and hydrophobic surface properties could explain potential alternative binding modes of the four cutinases on PLLA explaining their distinct activities. Biotechnol. Bioeng. 2017;114: 2481-2488. © 2017 Wiley Periodicals, Inc. [ABSTRACT FROM AUTHOR]

Blends of polyethylene terphalet (PET) with polylactic acid (PLA) were investigated to study the influence of the additive of PET on (tear, impact strength) and (transparency, color). The compositions were prepared in wt (20/80), (50/50), (80/20). Mechanical properties like tear strength and Impact Izod, and optical properties like colors and transparency were also reported. Polyethylene terphaletee decrease the tear strength when additive PET and Impact Izod strength of PLA was increased when additive PET when tested in the machine directions. Optical property such as colors was increased and the value of transparency was decreased as the loading of PET increased. [ABSTRACT FROM AUTHOR]

To study hydrolysis of aromatic and aliphatic polyesters cutinase 1 from Thermobifida cellulosilytica (Thc_Cut1) was expressed in P. pastoris. No significant differences between the expression of native Thc_Cut1 and of two glycosylation site knock out mutants (Thc_Cut1_koAsn and Thc_Cut1_koST) concerning the total extracellular protein concentration and volumetric activity were observed. Hydrolysis of poly(ethylene terephthalate) (PET) was shown for all three enzymes based on quantification of released products by HPLC and similar concentrations of released terephthalic acid (TPA) and mono(2-hydroxyethyl) terephthalate (MHET) were detected for all enzymes. Both tested aliphatic polyesters poly(butylene succinate) (PBS) and poly(3-hydroxybutyrate-co-3- hydroxyvalerate) (PHBV) were hydrolyzed by Thc_Cut1 and Thc_Cut1_koST, although PBS was hydrolyzed to significantly higher extent than PHBV. These findings were also confirmed via quartz crystal microbalance (QCM) analysis; for PHBV only a small mass change was observed while the mass of PBS thin films decreased by 93% upon enzymatic hydrolysis with Thc_Cut1. Although both enzymes led to similar concentrations of released products upon hydrolysis of PET and PHBV, Thc_Cut1_koST was found to be significantly more active on PBS than the native Thc_Cut1. Hydrolysis of PBS films by Thc_Cut1 and Thc_Cut1_koST was followed by weight loss and scanning electron microscopy (SEM). Within 96 h of hydrolysis up to 92 and 41% of weight loss were detected with Thc_Cut1_koST and Thc_Cut1, respectively. Furthermore, SEM characterization of PBS films clearly showed that enzyme tretment resulted in morphological changes of the film surface. [ABSTRACT FROM AUTHOR]

The present study addresses comprehensively the problem of producing polyesters through sustainable processes while using fully renewable raw materials and biocatalysts. Polycondensation of bio-based dimethyl adipate with different diols was catalyzed by cutinase 1 from Thermobifida cellulosilytica (Thc_cut1) under solvent free and thin-film conditions. The biocatalyst was immobilized efficiently on a fully renewable cheap carrier based on milled rice husk. A multivariate factorial design demonstrated that Thc_cut1 is less sensitive to the presence of water in the system and it works efficiently under milder conditions (50 °C; 535 mbar) when compared to lipase B from Candida antarctica (CaLB), thus enabling energy savings. Experimental and computational investigations of cutinase 1 from Thermobifida cellulosilytica (Thc_cut1) disclosed structural and functional features that make this serine-hydrolase efficient in polycondensation reactions. Bioinformatic analysis performed with the BioGPS tool pointed out functional similarities with CaLB and provided guidelines for future engineering studies aiming, for instance, at introducing different promiscuous activities in the Thc_cut1 scaffold. The results set robust premises for a full exploitation of enzymes in environmentally and economically sustainable enzymatic polycondensation reactions. [ABSTRACT FROM AUTHOR]

The next generation of plastics are expected to contribute to a massive reduction in the carbon footprint by the exploitation, in industrial productive processes, of renewable monomers such as polyols and dicarboxylic acids obtainable via biotechnological production. More specifically, there is a rising demand for advanced polyesters displaying new functional properties while meeting higher sustainability criteria. Polyesters are part of everyday life with applications in clothing, food packaging, car manufacturing and biomedical devices. This review is intended to provide an overview of the array of renewable building blocks already available for synthetic purposes and exploitable in the production of polyesters. Moreover, new greener routes for more environmentally friendly polyester production and processing are discussed, pointing out the major technological challenges. © 2016 Society of Chemical Industry [ABSTRACT FROM AUTHOR]

Natural fibers have gained much attention as reinforcing components in composite materials. Despite several interesting characteristics like low cost, low density, high specific properties and biodegradability they show poor compatibility with the polymer matrix. We have shown that it is possible to use a laccase from Trametes hirsuta as a biocatalyst to attach different types of functional phenolic molecules onto the fibers. A 5% incorporation of the functional molecules was achieved as measured via X-ray photoelectron spectroscopy (XPS) in flax although it was lower in coconut fibers. In combination with different mediators it was possible to broaden the activation scope and graft hydrophobic molecules like dimer fatty amines. Among the different mediators tested 1-hydroxybenzotriazole (HBT), 2,2,6,6-tetramethylpiperidin-1-yloxy (TEMPO) and 2'-azino-bis(3-ethylbenzothiazoline-6-sulphonic acid) (ABTS), TEMPO were the most effective achieving a 10% increase in carbon as measured by XPS. [ABSTRACT FROM AUTHOR]

The front cover of the journal "Green Chemistry" is presented.

ABSTRACT Modeling and comparison of the structures of the two closely related cutinases Thc_Cut1 and Thc_Cut2 from Thermobifida cellulosilytica DSM44535 revealed that dissimilarities in their electrostatic and hydrophobic surface properties in the vicinity to the active site could be responsible for pronounced differences in hydrolysis efficiencies of polyester (i.e., PET, polyethyleneterephthalate). To investigate this hypothesis in more detail, selected amino acids of surface regions outside the active site of Thc_Cut2, which hydrolyzes PET much less efficiently than Thc_Cut1 were exchanged by site-directed mutagenesis. The mutants were expressed in E. coli BL21-Gold(DE3), purified and characterized regarding their specific activities and kinetic parameters on soluble substrates and their ability to hydrolyze PET and the PET model substrate bis(benzoyloxyethyl) terephthalate (3PET). Compared to Thc_Cut2, mutants carrying Arg29Asn and/or Ala30Val exchanges showed considerable higher specific activity and higher kcat/ KM values on soluble substrates. Exchange of the positively charged arginine (Arg19 and Arg29) located on the enzyme surface to the non-charged amino acids serine and asparagine strongly increased the hydrolysis activity for 3PET and PET. In contrast, exchange of the uncharged glutamine (Glu65) by the negatively charged glutamic acid lead to a complete loss of hydrolysis activity on PET films. These findings clearly demonstrate that surface properties (i.e., amino acids located outside the active site on the protein surface) play an important role in PET hydrolysis. Biotechnol. Bioeng. 2013;110: 2581-2590. © 2013 Wiley Periodicals, Inc. [ABSTRACT FROM AUTHOR]

The aim of the study is to activate inert PET surface in order to introduce the carboxyl groups and to obtain its hydrophilic character. Two advanced and environmentally friendly techniques were used for these purposes: i) oxygen plasma activation; ii) enzymatic treatment by cutinase. Differently treated PET foils were studied in terms of carboxylic group content (non-aqueous potentiometric titrations, XPS) and hydrophobic/hydrophilic character (goniometry). Moreover, the influence of both activation procedures onto chitosan adsorption was examined by XPS, zeta potential measurements and ATR-FTIR spectroscopy. Obtained results show that plasma activation gives for around 19% higher amount of carboxylic groups than cutinase treatment and is during the storage less stable. Results clearly show that the use of both surfaces activation processes increases the ability of PET foils for chitosan adsorption. Due to the fact that chitosan is an antimicrobial agent, obtained materials may be applied as an active packaging system. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013 [ABSTRACT FROM AUTHOR]

Alkyd resins are polyesters containing unsaturated fatty acids that are used as binding agents in paints and coatings. Chemical drying of these polyesters is based on heavy metal catalyzed cross-linking of the unsaturated fatty acid moieties. Among the heavy-metal catalysts, cobalt complexes are the most effective, yet they have been proven to be carcinogenic. Therefore, strategies to replace the cobalt-based catalyst by environmentally friendlier and less toxic alternatives are under development. Here, we demonstrate for the first time that a laccase–mediator system can effectively replace the heavy-metal catalyst and cross-link alkyd resins. Interestingly, the biocatalytic reaction does not only work in aqueous media, but also in a solid film, where enzyme diffusion is limited. Within the catalytic cycle, the mediator oxidizes the alkyd resin and is regenerated by the laccase, which is uniformly distributed within the drying film as evidenced by confocal laser scanning microscopy. During gradual build-up of molecular weight, there is a concomitant decrease of the oxygen content in the film. A new optical sensor to follow oxygen consumption during the cross-linking reaction was developed and validated with state of the art techniques. A remarkable feature is the low sample amount required, which allows faster screening of new catalysts. [ABSTRACT FROM AUTHOR]

Enzyme application in polymer engineering is rapidly increasing and is set to revolutionize many industries. Given the multidisciplinary nature of this field, it has become clear that successful development of functional polymers entails tapping into advances in bioengineering, molecular biology, genetic engineering, chemical engineering, biochemistry, material science, nanotechnology, etc. This review summarizes the different strategies and reaction conditions that can influence the synthesis or modification of polymers. It is hoped that this review will provide scientists from different backgrounds with information on the different reaction engineering strategies for the successful development of functional polymers using oxidative enzymes. [ABSTRACT FROM AUTHOR]

A new esterase from Thermobifida halotolerans (Thh_Est) was cloned and expressed in E. coli and investigated for surface hydrolysis of polylactic acid (PLA) and polyethylene terephthalate (PET). Thh_Est is a member of the serine hydrolases superfamily containing the -GxSxG- motif with 85--87% homology to an esterase from T. alba, to an acetylxylan esterase from T. fusca and to various Thermobifida cutinases. Thh_Est hydrolyzed the PET model substrate bis(benzoyloxyethyl)terephthalate and PET releasing terephthalic acid and mono-(2-hydroxyethyl) terephthalate in comparable amounts (19.8 and 21.5 mmol/mol of enzyme) while no higher oligomers like bis-(2-hydroxyethyl) terephthalate were detected. Similarly, PLA was hydrolyzed as indicated by the release of lactic acid. Enzymatic surface hydrolysis of PET and PLA led to a strong hydrophilicity increase, as quantified with a WCA decrease from 90.8° and 75.5° to 50.4° and to a complete spread of the water drop on the surface, respectively. [ABSTRACT FROM AUTHOR]

A new cutinase from Thermobifida alba (Tha_Cut1) was cloned and characterized for polyethylene terephthalate (PET) hydrolysis. Tha_Cut1 showed a high degree of identity to a T. cellulolysitica cutinase with only four amino acid differences outside the active site area, according to modeling data. Yet, Tha_Cut1 was more active in terms of PET surface hydrolysis leading to considerable improvement in hydrophilicity quantified based on a decrease of the water contact angle from 87.7° to 45.0°. The introduction of new carboxyl groups was confirmed and measured after esterification with the fluorescent reagent alkyl bromide, 2-(bromomethyl) naphthalene (BrNP), resulting in a fluorescence emission intensity increase from 980 to 1420 a.u. On the soluble model substrates p-nitrophenyl acetate (PNPA) and p-nitrophenyl butyrate (PNPB), the cutinase showed Km values of 213 and 1933 μM and kcat values of 2.72 and 6.03 s−1 respectively. The substrate specificity was investigated with bis(benzoyloxyethyl)terephthalate (3PET) and Tha_Cut1 was shown to release primarily 2-hydroxyethyl benzoate. This contrasts with the well-studied Humicula insolens cutinase which preferentially liberates terminal benzoic acid from 3PET. [ABSTRACT FROM AUTHOR]

From a screening on agar plates with bis(benzoyloxyethyl) terephthalate (3PET), a Bacillus subtilis p-nitrobenzylesterase (BsEstB) was isolated and demonstrated to hydrolyze polyethyleneterephthalate (PET). PET-hydrolase active strains produced clearing zones and led to the release of the 3PET hydrolysis products terephthalic acid (TA), benzoic acid (BA), 2-hydroxyethyl benzoate (HEB), and mono-(2-hydroxyethyl) terephthalate (MHET) in 3PET supplemented liquid cultures. The 3PET-hydrolase was isolated from non-denaturating polyacrylamide gels using fluorescein diacetate (FDA) and identified as BsEstB by LC-MS/MS analysis. BsEstB was expressed in Escherichia coli with C-terminally fused StrepTag II for purification. The tagged enzyme had a molecular mass of 55.2 kDa and a specific activity of 77 U/mg on p-nitrophenyl acetate and 108 U/mg on p-nitrophenyl butyrate. BsEstB was most active at 40°C and pH 7.0 and stable for several days at pH 7.0 and 37°C while the half-life times decreased to 3 days at 40°C and only 6 h at 45°C. From 3PET, BsEstB released TA, MHET, and BA, but neither bis(2-hydroxyethyl) terephthalate (BHET) nor hydroxyethylbenzoate (HEB). The kcat values decreased with increasing complexity of the substrate from 6 and 8 (s−1) for p-nitrophenyl-acetate (4NPA) and p-nitrophenyl-butyrate (4NPB), respectively, to 0.14 (s−1) for bis(2-hydroxyethyl) terephthalate (BHET). The enzyme hydrolyzed PET films releasing TA and MHET with a concomitant decrease of the water-contact angle (WCA) from 68.2° ± 1.7° to 62.6° ± 1.1° due to formation of novel hydroxyl and carboxyl groups. These data correlated with a fluorescence emission intensity increase seen for the enzyme treated sample after derivatization with 2-(bromomethyl)naphthalene. © 2011 American Institute of Chemical Engineers Biotechnol. Prog., 2011 [ABSTRACT FROM AUTHOR]