Search

The use of phenoxy nanocomposite films as carriers of nanofillers involving multiwalled carbon nanotubes and nanoclays is successfully demonstrated for application in epoxy carbon fibers reinforced composites (CFRC) processed by RTM. Model studies on individual nanocomposite filaments embedded in epoxy precursors show that the nanofillers are passively transported by the interdiffusion gradient during heating over distance around 800 lm. A morphology gradient is generated after reaction induced phase separation and the nanofillers end up in the epoxy, despite their initial dispersion in the phenoxy. The proof of concept is extended to CFRC panels where nanocomposite phenoxy films are prepositioned between every odd carbon layer of the preform. Carbon nanotubes are filtered by the carbon fabrics, which limits their full diffusion and that of phenoxy through the preform. This has negative consequences on fracture toughness (GIc). For nanoclay, GIc is rather slightly improved although the origin is not fully clear.

We explore the influence of the interdiffusion of two thermoplastic tougheners and RTM6 epoxy resin precursors on the resulting morphologies after curing and the consequences on delamination toughness of the corresponding carbon fiber reinforced composites. Two thermoplastics with contrasting Tg and compatibility, i.e. poly(ether sulfone) (PES) and phenoxy are compared. The dramatic improvement of the interlaminar fracture toughness (GIC) found for the phenoxy-RTM6 system as compared to the pure thermoset reference can be ascribed to the broad morphology gradient only observed for that system. By contrast, the PES-RTM6 system is characterized by a steep morphology gradient and a corresponding decrease of as compared to the reference.

Toughening of epoxy thermosets with thermoplastics is an important avenue towards improved properties of high-performance systems. The main focus of the work reported was to study the complex issue of interdiffusion between thermoplastics and epoxy resin precursors, using a combination of experimental and numerical simulation methods, in order to understand the key parameters driving the process. Diameter changes of thermoplastic filaments in contact with epoxide and diamine precursors have been followed and an original approach using carbon nanotubes as tracers of the filament swelling front has been developed. This method shows that the improved mobility of low-molecular-weight resin monomers as well as the greater mobility of phenoxy of lower glass transition temperature as compared to poly(ether sulfone) control dissolution by favouring the penetration of precursors into the thermoplastic and lead to both swelling of the outer part of the filaments and reduction of the inner unaffected core. Simulation by molecular dynamics supports the idea that diffusion of polymer macromolecules remains limited compared to the dominant effect of precursor diffusion. Indeed, low diffusion coefficients have been predicted for thermoplastic oligomers compared to resin monomers. For the latter, the calculated values correlate well with the experimental data measured during interdiffusion

BACKGROUND: Preparative fractionation techniques are currently used in order to obtain large amounts of polyethylene fractions. Preparative successive solution fractionation (SSF) and temperature rising elution fractionation (TREF) are compared as regards obtaining, at a multi-gram scale, low-dispersity fractions of high-density polyethylene (HDPE). The operative separation mechanisms during a SSF of a broad HDPE, which are not yet totally elucidated, are also studied in this work. RESULTS: SSF and TREF approaches lead to the separation of HDPE macromolecules according to their molar masses. If very homogeneous fractions (dispersities from 1.1 to 1.3) are isolated in TREF at the lowest elution temperature, the collected mass is too low. At higher elution temperatures, the fractions have too broad a molar mass distribution (dispersities from 2.7 to 3.7). With the SSF procedure, dispersities are not as low as for the first TREF fractions. But, the relative weight fraction is better distributed between the different extraction temperatures. The molar mass distribution exhibits a dispersity of around 1.9. CONCLUSION: The SSF method is the most suitable way to obtain large gram amounts of low-dispersity (ca 2) HDPE fractions over a wide molar mass range. Complementary gram-scale rheological characterization is thus possible enabling a better comprehension of the SSF mechanism. Liquid-liquid demixing is the main mechanism in SSF, but its relative importance depends on polymer characteristics and solvent quality. (C) 2008 Society of Chemical Industry

BACKGROUND: The surface properties of high-density polyethylene and linear low-density polyethylene were modified by grafting urethane monoacrylate monomer under UV irradiation. This graft polymerization was carried out on native substrates and on substrates pre-treated by wet oxidation, for different oxidation times. RESULTS: As the urethane monacrylate layer is crosslinked, its grafting efficiency was checked by dissolving the polyethylene substrates in hot toluene. Grafting was evidenced by Fourier transform infrared spectroscopy of the obtained residues, which showed that both the characteristic urethane acrylate (3350 cm(-1)) and polyethylene (2920, 730 and 720 cm(-1)) bands were observable for any polyethylene oxidation time. For an oxidation time longer than 10 hours, acrylate grafting was homogeneous and the grafted surface was smooth with a roughness of less than 10 nm. In addition, X-ray photoelectron spectroscopy analysis of the residues revealed that O/C had an average value of 0.19, which is lower than the value corresponding to pure acrylate (0.42), whereas N/C had an average value of 0.068, also lower than that of pure acrylate (0.09), thus confirming the grafting. CONCLUSION: A urethane monoacrylate layer was grafted on native and oxidized polyethylene films. For highly oxidized films, the grafted surfaces are smooth and homogeneous. (C) 2008 Society of Chemical Industry.

We characterize sparsely and randomly branched polycarbonate and fractions thereof by a combination of solution and rheological techniques, and we compare the observations with the results of Monte Carlo simulations as well as tube-based modeling. On-line coupling of size exclusion chromatography with intrinsic viscosity (SEC-IV) yields values for the viscosity branching index g', which deviate significantly from linear behavior above approximately 0.3 branches per chain. The experimental g' also follows closely the predictions for the geometric branching factor g calculated by Monte Carlo simulations of the polymer structure across the entire molar mass distribution (g=g'). The Monte Carlo simulations provide an explicit description of the molecular architectures present and can therefore in principle be used to test models suitable for sparsely branched polymers. Experimental dynamic moduli of unfractionated and fractionated samples are compared with predictions of a tube-based model recently published in van Ruymbeke et al. [J. Non-Newt. Fluid Mech. 128, 7-22 (2005b)]. When the model is calibrated for polydisperse linear polycarbonate, discrepancies between the predicted and measured dynamic moduli are clearly observed at levels well below the detection limit of branching by the SEC-IV coupling method. The comparison between observed and predicted moduli is therefore a very sensitive method for the detection of sparse long chain branching in poorly and moderately entangled polymers, of which polycarbonate is a good example. (c) 2006 The Society of Rheology.

Surface modification of high-density-polyethylene (HDPE) and linear-low-density polyethylene (LLDPE) films is promoted by sodium hypochlorite solutions using two different processes (I and IT). Such an oxidation system introduces limited amounts of carbonyl-carboxyl and hydroxyl groups onto the surface of hydrocarbon polymers. FTIR, XPS, and SEM were used to assess the efficiency of the oxidation. The hydrophilicity of the studied surfaces was investigated by the sessile drop technique and the Wilhelmy plate and a plausible oxidation mechanism is proposed. (c) 2006 Wiley Periodicals, Inc.

We have developed a sensitive method to detect very low levels of long chain branching in sparsely branched polymers and applied it to high-density polyethylene samples with broad molar mass distribution obtained by Ziegler-Natta, Phillips, and metallocene catalysis. We compare experimental dynamic moduli with predicted values. The predicted moduli, which are only valid for truly linear chains, are computed from a known molar mass distribution by the application of a modified time-dependent diffusion reptation model described in [van Ruymbeke et al., Macromolecules 35, 2689 (2002)]. Discrepancies between experimental and predicted moduli are observed at branching levels below the usual detection limit Of C-13 nuclear magnetic resonance (about I branch per 10000 carbon atoms). Our method is easier to implement and the results more clearcut than those obtained by the zero-shear viscosity method. The sensitivity is comparable with the activation energy spectrum method described in [Wood-Adams et al., Macromolecules 33, 7489 (2000)]. The use of our method is however not restricted to thermorheologically complex polymers. The interest of polymer fractionation is also demonstrated for the detection of extremely low levels of long chain branching. (c) 2005 The Society of Rheology.

The previously developed model [Polym Bull 2000, 44, 525] used to characterize the porous gel inside a gel permeation chromatography (GPC) column, has been extended to also include the interstitial space between the macroscopic gel particles. The hydrodynamic dimensions for 12 polystyrene (PS) standards, measured by GPC with differential refractive index (DRI), differential viscometry (VISCO), and multiangle laser light scattering (MALLS) detectors, have been used to determine the fractal parameters of the polystyrene-divinylbenzene gel corresponding to four commercial columns. The new developed model enables to predict the calibration curve for the sets of coupled columns based on the parameters of each column. (C) 2004 Wiley Periodicals, Inc.

Owing to their low polydispersity and their well controlled molecular architecture, 3-arms stars polystyrenes made by anionic synthesis are suitable models to study the solution proper-ties of long chain branched polymers. A fine characterization of such polymers by size exclusion chromatography-viscometry has shown that they often contain unwanted linear chains, leading to chromatograms presenting overlapping peaks. A mathematical procedure has been developed in order to deconvolute these chromatograms and has been validated, thanks to blends of polystyrene standards. It allows one to calculate the purity of the sample as well as the intrinsic viscosity and molar mass distribution of each component. For stars with three arms of the same length, branching parameters have also been calculated and a viscosity law has been established. (C) 2002 Elsevier Science Ltd. All rights reserved.

Chlorinated polypropylene (CPO) is commonly used as an adhesion promoter for paint on polypropylene/ ethylene - propylene copolymer blends (PP/EP). An adhesion mechanism frequently proposed in the literature is the CPO diffusion into the substrate, leading to molecular entanglement. It is shown here that CPO and PP/EP are immiscible. On the other hand, the use of radiolabelled CPO allowed quantification of CPO diffusion into PP/EP substrates as a function of several parameters and under conditions which simulate industrial practice. Diffusion requires substrate swelling by the solvent. This explains that it increases with the EP content of the material, with the solvent ability to swell the substrate, and with the thickness of the paint. For baked samples, diffusion passes through a maximum when the delay between CPO application and baking is varied. This is due to a balance between two processes working in opposite directions, i.e. substrate swelling and solvent evaporation.

In this study we correlate parameters describing molecular structure (molar mass distribution, short chain branching content, intermolecular heterogeneity) of different ethylene-hexene Cr-catalyzed copolymers, with slow crack growth and rapid crack propagation resistances, respectively measured with Bent Strip and Charpy tests. The PTREF technique, coupled with classical techniques, was used. Two new indices were proposed to correlate mechanical properties and molecular structure. (C) 2001 John Wiley & Sons, Inc.

The purpose of this study is to propose a correlation between IR spectra and molecular structure of ethylene-propylene (EP) copolymers possibly blended with isotactic polypropylene (iPP). The method is based on the deconvolution of the spectrum in the CH2-rocking range, i.e., 800-680 cm(-1), where the bands of interest overlap. The six bands present in this region were signal averaged in position and width. The spectra were then deconvoluted (curve fitted) assuming a Lorentzian shape for the bands. The band at 1167 cm(-1) (with a shoulder at 1156 cm(-1)) corresponding to a CH3 vibration is considered as an internal standard. The method was checked by varying some fitting parameters. In order to realize some quantitative measurements, calibration curves were established with some EP samples, characterized by C-13 NMR, which were used as standards. The amounts of total -(CH2-CH2)- units (ethylene units), isolated ethylene and structural defaults in PP were determined for different iPP/EP blends. Ethylene crystallinity has also been determined. A good correlation was evidenced between infrared and C-13 NMR measurements. (C) 2000 John Wiley & Sons, Inc.

High-resolution solid-state C-13-NMR, differential scanning calorimetry, and Fourier transform infrared spectroscopy were used to compare the very low crystalline degree and crystallite dimensions of ethylene runs in a series of isotactic polypropylene/ethylene-propylene copolymer blends exhibiting a range of properties. Results obtained from the three techniques on samples with the same thermal history are in a satisfying qualitative agreement. They show that the morphology of the polyethylene domains is only very slightly dependent on the viscosity ratio of the two blend components. On the opposite, it is largely governed by the ethylene content of the ethylene-propylene copolymer. (C) 1999 John Wiley & Sons, Inc.

The fracture toughness of PP-EP (Polypropylene-Ethylene-Propylene) blends is studied at room temperature using the "essential work of fracture" (EWF) method. The results obtained by applying this method are compared with those of puncture and tensile tests. Whereas the classical puncture tests do not allow classifying the rubber-toughened PP-EP blends, the EWF method proves to be a sensitive technique to monitor the effect of composition and morphology of the blend on fracture toughness. Moreover, the application of the EWF method allows monitoring how the fracture toughness of a material depends on its ability to deform extensively before fracturing and on its capacity to bear some load. A good combination of these two properties thus yields materials presenting an optimal fracture toughness.

Characterization of high-temperature poly(ether sulfone) (HTPES) molar mass was performed using light scattering, viscometry and size-exclusion chromatography (SEC). In pure N-methyl-2-pyrrolidone (NMP), a large increase of the reduced viscosity at low concentration was observed. By addition of a salt such LiBr, this effect was suppressed. Using the viscosity laws of HTPES and poly(methyl methacrylate) (PMMA) in NMP + LiBr the SEC method was standardized via the universal calibration established with PMMA standards. The Mark-Houwink-Sakurada (MHK) relationship for HTPES in NMP containing 0,1 mol/L LiBr at 25 degrees C with the intrinsic viscosity [eta] and molecular weight M afforded the MHK constants K = 33,8 . 10(-5) dL . mol(a) . g(1+a) and a = 0,70. The weight-average molar masses obtained from SEC were very close to those obtained from light scattering. A comparison of number-average molar masses obtained from H-1 NMR, potentiometric titration of chain-ends, and from SEC has shown more discrepancy for high molar masses. The study of dilute solution properties of HTPES macromolecules has shown the marked decrease of anisotropy with the number of repeating units, the low values of the characteristic ratio and of the Kuhn segment. All these conformational properties are similar to those of freely rotating chains.

The changes in the molecular composition of purified commercial polystyrene following thermal degradation were analyzed by gel permeation, reverse phase liquid and gas chromatography. Three major low molecular weight compounds were identified: styrene monomer, a dimer, and a trimer. The composition, the molecular weight, and the structure of the two oligomers were determined by elementary analysis, mass spectroscopy, nuclear magnetic resonance, and infrared spectroscopy. A linear structure with an ethylene end group is proposed for the two oligomers. The appearance of these degradation compounds is explained on the basis of an intramolecular mechanism involving chain-end folding and transfer of a labile tertiary hydrogen.