Search

Waste carbon fibers as reinforcing elements in construction materials have recently gained increasing interest from researchers, providing outstanding strength performance and a lower environmental footprint compared to virgin fibers. Combination with cement-free binders, namely alkali-activated materials, is becoming increasingly important for sustainable development in the construction industry. This paper presents results relating to the potential use of waste carbon fibers in alkali-activated mortars. The waste carbon fiber fraction utilized in this research is difficult to integrate as reinforcement in ceramic–cementitious matrices due to its agglomerated form and chemical inertness. For this reason, a nanoceramic coating pretreatment based on nanoclay has been implemented to attempt improvements in terms of deagglomeration, dispersibility, and compatibility with alkali-activated materials. After chemical–physical and microstructural analysis on the nanoclay-plated fibers (including X-ray diffraction, IR spectroscopy, contact angle measurements, and electron microscopy) mortars were produced with four different dosages of treated and untreated waste fibers (0.25 wt.%, 0.5 wt.%, 0.75 wt.%, and 1 wt.%). Mechanical tests and fractographic investigations were then performed. The nanoclay coating interacts compatibly with the waste carbon fibers and increases their degree of hydrophilicity to improve their deagglomeration and dispersion. Compared to the samples incorporating as-received fillers, the addition of nanoclay-coated fibers improved the strength behavior of the mortars, recording a maximum increase in flexural strength of 19% for a fiber content of 0.25 wt.%. This formulation is the only one providing an improvement in mechanical behavior compared to unreinforced mortar. Indeed, as the fibrous reinforcement content increases, the effect of the nanoclay is attenuated by mitigating the improvement in mechanical performance. [ABSTRACT FROM AUTHOR]

This paper explores the new potential strategy of using fine recycled aggregates (fRA) derived from waste 3D printed concrete (3DPC) as a substitute for cement in additive manufacturing. This study hypothesizes that fRA can optimize mixture design, reduce cement content, and contribute to sustainable construction practices. Experimental programs were conducted to evaluate the fresh and hardened properties, printability window, and buildability of 3DPC mixes containing fRA. Mixes with replacement rates of cement with fRA by 10 vol%, 20 vol%, 30 vol%, 40 vol%, and 50 vol% were produced. A comprehensive experimental protocol consisting of rheological studies (static and dynamic yield stress), dynamic elastic modulus determination (first 24 h of hydration), flexural and compressive strengths (2 d and 28 d), and an open porosity test was performed. The obtained results were verified by printing tests. In addition, an economic and environmental life cycle assessment (LCA) of the mixes was performed. The results indicate that up to 50 vol% cement replacement with fRA is feasible, albeit with some technical drawbacks. While fRA incorporation enhances sustainability by reducing CO2 emissions and material costs, it adversely affects the printability window, green strength, setting time, and mechanical properties, particularly in the initial curing stages. Therefore, with higher replacement rates (above 20 vol%), potential optimization efforts are needed to mitigate drawbacks such as reduced green strength and buildability. Notably, replacement rates of up to 20 vol% can be successfully used without compromising the overall material properties or altering the mixture design. The LCA analysis shows that reducing the cement content and increasing the fRA addition results in a significant reduction in mix cost (up to 24%) and a substantial decrease in equivalent CO2 emissions (up to 48%). In conclusion, this study underscores the potential of fRA as a sustainable alternative to cement in 3D printed concrete. [ABSTRACT FROM AUTHOR]

This study presents a new approach towards the production of sol-gel silica-coated Bi2O3/Gd2O3 cement additives towards the improvement of early mechanical performance and radiation attenuation. Two types of silica coatings, which varied in synthesis method and morphology, were used to coat Bi2O3/Gd2O3 structures and evaluated as a cement filler in Portland cement pastes. Isothermal calorimetry studies and early strength evaluations confirmed that both proposed coating types can overcome retarded cement hydration process, attributed to Bi2O3 presence, resulting in improved one day compressive strength by 300% and 251% (depending on coating method) when compared to paste containing pristine Bi2O3 and Gd2O3 particles. Moreover, depending on the type of chosen coating type, various rheological performances of cement pastes can be achieved. Thanks to the proposed combination of materials, both gamma-rays and slow neutron attenuation in cement pastes can be simultaneously improved. The introduction of silica coating resulted in an increment of the gamma-ray and neutron shielding thanks to the increased probability of radiation interaction. Along with the positive early age effects of the synthesized structures, the 28 day mechanical performance of cement pastes was not suppressed, and was found to be comparable to that of the control specimen. As an outcome, silica-coated structures can be successfully used in radiation-shielding cement-based composites, e.g. with demanding early age performances. [ABSTRACT FROM AUTHOR]

Incorporating metal oxide nanoparticles into cement-based composites delays the hydration process and strength gain of cementitious composites. This study presents an approach toward improving the performance of bismuth oxide (Bi2O3) and gadolinium oxide (Gd2O3) particles in cementitious systems by synthesizing core–shell structures via a sol-gel process. Two types of silica coatings on cementitious pastes with 5% and 10% substitution levels were proposed. The rheology, hydration, and mechanical properties of the pastes were analyzed to determine the relationship between the coating type and nanoparticle concentration. The results indicate that despite the significant disparities in the performance of the resulting material, both methods are appropriate for cement technology applications. Bi2O3's silica coatings accelerate the hydration process, leading to early strength development in the cement paste. However, due to the coarse particle size of Gd2O3, silica coatings exhibited negligible effects on the early age characteristics of cement pastes. [ABSTRACT FROM AUTHOR]

The utilization of waste fibers in the production of reinforced concrete materials offers several advantages, including reducing environmental strain and socio-economic impacts associated with composite waste, as well as enhancing material performance. This study focuses on the development of cementitious mortars using secondary waste carbon fibers, which are by-products derived from the industrial conversion of recycled fibers into woven/non-woven fabrics. The research primarily addresses the challenge of achieving adequate dispersion of these recycled fibers within the matrix due to their agglomerate-like structure. To address this issue, a deagglomeration treatment employing nanoclay conditioning was developed. The functionalization with nanoclay aimed to promote a more uniform distribution of the reinforcement and enhance compatibility with the cementitious matrix. Various fiber weight percentages (ranging from 0.5 w/w% to 1 w/w% relative to the cement binder) were incorporated into the fiber-reinforced mix designs, both with and without nanoceramic treatment. The influence of the reinforcing fibers and the compatibility effects of nanoclay were investigated through a comprehensive experimental analysis that included mechanical characterization and microstructural investigation. The effectiveness of the nanoceramic conditioning was confirmed by a significant increase in flexural strength performance for the sample incorporating 0.75 w/w% of waste fibers, surpassing 76% compared to the control material and exceeding 100% compared to the fiber-reinforced mortar incorporating unconditioned carbon fibers. Furthermore, the addition of nanoclay-conditioned carbon fibers positively impacted compression strength performance (+13% as the maximum strength increment for the mortar with 0.75 w/w% of secondary waste carbon fibers) and microstructural characteristics of the samples. However, further investigation is required to address challenges related to the engineering properties of these cementitious composites, particularly with respect to impact resistance and durability properties. [ABSTRACT FROM AUTHOR]

Due to global environmental concerns related to climate change, the need to improve the service life of structures and infrastructures is imminently urgent. Structural elements typically suffer service life reductions, leading to poor environmental sustainability and high maintenance costs. Graphene oxide nanosheets (GONSs) effectively dispersed in a cement matrix can promote hydration, refine the microstructure and improve interfacial bonding, leading to enhanced building materials' performance, including mechanical strength and transport properties. Cement-based nanocomposites engineered with GONSs were obtained using two commercial nanofillers, a GO water suspension and a free-flowing GO nanopowder, characterized by fully comparable morphology, size and aspect ratio and different oxidation degrees (i.e., oxygen-to-carbon molar ratio), 0.55 and 0.45, respectively. The dosage of the 2D-nanofiller ranged between 0.01% and 0.2% by weight of cement. The electrical and thermal properties were assessed through electrochemical impedance spectroscopy (EIS) and a heat flow meter, respectively. The results were discussed and linked to micrometric porosity investigated by micro-computed tomography (μ-CT) and transport properties as determined by initial surface absorption test (ISAT), boil-water saturation method (BWS) and chloride ion penetration test. Extra-low dosage mortars, especially those loaded with a lower oxidation degree (i.e., 0.45GO), showed decreased permeability and improved barrier to chloride ion transport combined with enhanced thermal and electrical conductivity with respect to that of the control samples. [ABSTRACT FROM AUTHOR]

The increase in concrete structures' durability is a milestone to improve the sustainability of buildings and infrastructures. In order to ensure a prolonged service life, it is necessary to detect the deterioration of materials by means of monitoring systems aimed at evaluating not only the penetration of aggressive substances into concrete but also the corrosion of carbon-steel reinforcement. Therefore, proper data collection makes it possible to plan suitable restoration works which can be carried out with traditional or innovative techniques and materials. This work focuses on building heritage and it highlights the most recent findings for the conservation and restoration of reinforced concrete structures and masonry buildings. [ABSTRACT FROM AUTHOR]

Additive manufacturing (AM), also referred as 3D printing, is a technology that enables building automated three-dimensional objects in a layer-by-layer manner. AM of cement-based and alkali-activated composites has gathered attention over the last decade and is one of the most rapidly developing civil engineering fields. Development of proper mixture compositions which are suitable in fresh and hardened state is one of the key challenges of AM technology in construction. As the behaviour of cement-based materials (CBM) and alkali-activated materials (AAM) is determined by chemical and physical processes at the nano-level, incorporation of nano- and micro-sized admixtures has great influence on the performance of printable composites. These modifications are attributed to the unique reactivity of nanoparticles associated with their small size and large surface area. This review paper summarizes recent developments in the application of nano- and micro-particles on 3D printable cementitious composites and how they influence the performance of 3D-printed construction materials. The research progress on nano-engineered CBM and AAM is reviewed from the view of fresh and hardened properties. Moreover, comparison between nano- and micro-sized admixtures including nanosilica, graphene-based materials, and clay nanoparticles as well as chemical admixtures such as viscosity-modifying admixtures and superplasticizers is presented. Finally, the existing problems in current research and future perspectives are summarized. This review provides useful recommendations toward the significant influence of nano- and micro-sized admixtures on the performance of 3D printable CBMs. [ABSTRACT FROM AUTHOR]

Portland Cement Concrete (PCC) pavement was studied with incorporation of an environmentally friendly eco-additive, sodium acetate (C2H3NaO2). This additive was added to PCC pavement in three different percentages of 2%, 4% and 6% of binder weight. For a comprehensive elucidation of the eco-additive incorporation on the performance of PCC pavement, casted samples were cured in three different environments, namely: water, outdoors and pond water. Water absorption tests, flexural and compressive strength tests after 7 and 28 days of curing were conducted and results compared with the control samples without any addition of sodium acetate. Results demonstrated a significant improvement in the impermeability, compressive strength and flexural strength of PCC pavement when sodium acetate concrete is cured in a water bath and outdoors. However, no/little improvement in the impermeability, compressive strength and flexural strength was observed in sodium acetate samples that were cured in pond water. Microstructural analysis of treated samples by using scanning electron microscopy (SEM) illustrated the strengthening effect that sodium acetate provides to the pore structure of concrete pavement. [ABSTRACT FROM AUTHOR]

This article is aimed at investigating the long‐term performance of three original hydrophobic materials, namely, sodium acetate, fluoropolymer, and silicone resin. Their performance was compared with traditional silane when applied to fully dry concrete, fully saturated concrete, and concrete with 2 and 4% moisture content. A recently developed freeze–thaw process, which is based on temperature and humidity variations, was employed in this study to assess the durability of applied materials. The outcomes of the adopted freeze–thaw system were compared with the results obtained from running a conventional freeze–thaw test. Mass change, water absorption, and microcracks development of treated concrete were investigated and compared with untreated concrete after completing 6 months of freeze–thaw cycles. Results confirmed the high affinity of the proposed materials to moisture at application time compared with silane. Additionally, it was demonstrated that moisture content has a critical impact on the bonding between applied materials and concrete, hence their efficacy in enhancing the durability of concrete. [ABSTRACT FROM AUTHOR]

Hot metal gas forming (HMGF) is a desirable way for the automotive industry to produce complex metallic parts with poor formability, such as aluminum alloys. A simple hot gas forming method was developed to form aluminum alloy tubes using flame heating. An aluminum alloy tube was heated by a flame torch while the tube was rotated and compressed using a lathe machine and simultaneously pressurized with a constant air pressure. The effects of the internal pressure and axial feeding on expansion and wall thickness distribution were examined. The results showed that the proposed gas forming method was effective for forming aluminum alloy tubes. It was also indicated that axial feeding is a vital parameter to prevent reductions in wall thickness by supplying the material flow during the forming process. [ABSTRACT FROM AUTHOR]

An eco-friendly pre-treatment coupled with surface functionalisation were developed to enhance the quality of wheat straw particles to be used for development of high-performance polylactic acid (PLA) compressed strawboard. Eco-friendly hybrid pre-treatment (i.e., hot water followed by steam, H+S) and surface functionalisation processes employing attapulgite nanoclay (AT) and graphene nanoplatelets (G) were used to obtain an appropriate wheat straw surface quality while increasing its compatibility with the PLA matrix. The successful pre-treatment and surface functionalisation of wheat straw particles was verified through characterisation techniques, including SEM, FTIR, XRD, Raman spectroscopy, and TGA. Tensile strength and water absorption properties of compressed strawboards were examined to investigate the influence of pre-treatment and surface functionalisation of wheat straws. The maximum tensile strengths of 28 MPa and 27 MPa were recorded for 10 H+S-AT and 10 H+S-G samples, respectively, which are considerably higher than the value (i.e., 9.7 MPa) registered for the sample without pre-treatment and surface functionalisation (i.e., 10UN). The lowest water absorption after 24 h of immersion was registered for 10UN-G (i.e., 1.6%), which is 11% and 31% lower than the 10UN and 10 H+S samples, respectively. The effect is attributed to an improved interfacial bond between wheat straw and PLA matrix due to the graphene surface functionalisation, as evidenced by the SEM. • Dual enhancement of pre-treatment and surface nano-functionalising was proposed. • Pre-treatment and functionalising effects on the straw's structure were verified. • Crosslinking effect of surface functionalising agents is confirmed. • Maximum tensile strength of 28 MPa was registered for 10 H+S-AT. • The developed composites can be used in several applications, e.g., construction and automotive industry. [ABSTRACT FROM AUTHOR]

Utilising wheat straw reinforced OPC-free composites in the construction industry requires efficient, eco-friendly pre-treatment coupled with surface functionalisation methods to turn it into a high-performance material. Herein, alkali-activated material (AAM) was used as an OPC-free matrix, while eco-friendly hybrid pre-treatment and surface functionalisations were applied to mitigate the surface quality deficiencies of wheat straw and improve its compatibility with low-carbon binders. Wheat straw particles were subjected to a mild physical pre-treatment (hot-water followed by steam) and surface functionalisation using attapulgite nanoclay and graphene nanoplatelets to improve their capacity as an effective reinforcing material in AAM. Comprehensive characterisation verified successful pre-treatment and surface functionalisation, which led to the improved interfacial bond between wheat straw and AAM. The best results were obtained for the AAM samples reinforced with pre-treated straw that was functionalised with attapulgite nanoclay (i.e., H+S-AT), in which the volume of permeable voids decreased by 18%, while compressive and flexural strength at 90 d increased by 41% and 27%, respectively, compared to the control sample. However, the effect on the thermal properties of the resulted composites was not significant. • Hybrid pre-treatment and functionalising method using nanomaterials is presented. • Surface functionalising methods with AT nanoclay and G nanoplatelets were tested. • The deterioration mechanisms of wheat straw reinforced AAM were explained. • Improved compatibility of straw particles in the alkali-activated matrix was found. • Attapulgite functionalisation of straw improves compressive and flexural strengths. [ABSTRACT FROM AUTHOR]

The impact of extra-low dosage (0.01% by weight of cement) Graphene Oxide (GO) on the properties of fresh and hardened nanocomposites was assessed. The use of a minimum amount of 2-D nanofiller would minimize costs and sustainability issues, therefore encouraging the market uptake of nanoengineered cement-based materials. GO was characterized by X-ray Photoelectron Spectroscopy (XPS), Fourier-transform infrared spectroscopy (FTIR), Atomic Force Microscopy (AFM), X-ray Diffraction (XRD), and Raman spectroscopy. GO consisted of stacked sheets up to 600 nm × 800 nm wide and 2 nm thick, oxygen content 31 at%. The impact of GO on the fresh admixtures was evaluated by rheology, flowability, and workability measurements. GO-modified samples were characterized by density measurements, Scanning Electron Microscopy (SEM) analysis, and compression and bending tests. Permeability was investigated using the boiling-water saturation technique, salt ponding test, and Initial Surface Absorption Test (ISAT). At 28 days, GO-nanocomposite exhibited increased density (+14%), improved compressive and flexural strength (+29% and +13%, respectively), and decreased permeability compared to the control sample. The strengthening effect dominated over the adverse effects associated with the worsening of the fresh properties; reduced permeability was mainly attributed to the refining of the pore network induced by the presence of GO. [ABSTRACT FROM AUTHOR]

• Wheat straw optimised as feedstock for bio-composites. • Detection and removal of defects prior to bio-composite manufacture. • Significant tensile performance improvement of bio-composites. • Eco-friendly combination of physical pre-treatments to improve the surface. Individual and hybrid pre-treatments, including hot water, steam and microwave were used on wheat straw to mitigate the surface quality deficiencies for an intimate interfacial bond between substrate and Polylactic Acid matrix. Microstructural analysis showed the expansion of cells due to the pre-treatments which in turn promotes mechanical entanglement between wheat straw and PLA, thus, improving the tensile properties of bio-based composites. The tensile strength, elongation at break, elastic modulus, and toughness increased by 166 %, 18 %, 68 %, and 285 %, respectively, for hot water followed by steam pre-treated wheat straw bio-based composites compared to untreated. [ABSTRACT FROM AUTHOR]

The utilisation of biochar, the carbon negative product of pyrolysis, reduces the carbon footprint of the cementitious composites as it possesses the potential to replace the consumption of Portland cement. In a systematic investigation, biochar was used as a partial cement replacement for up to 20 wt% in both cement pastes and mortars. A comprehensive experimental framework was conducted to evaluate the impact of biochar replacement on the performance of (i) cement paste in terms of hydration kinetics, rheology, strength development, porosity, and (ii) mortars in terms of mechanical, thermal, and transport properties. In addition, the durability of developed mortars, including freezing and thawing resistance, thermal resistance, acid (corrosion) resistance, flammability, and smoke production, were examined. The results revealed that lower replacement rates of cement with biochar (up to 5 wt%) do not substantially change the performance of cementitious composites. However, incorporating biochar in higher dosages (i.e., 20 wt%) influenced the hydration process, reduced flexural and compressive strengths by 49% and 29%, respectively, and increased the water absorption coefficient by 60% compared to control specimens. The same cement mortar demonstrated the most promising freeze-thaw (i.e., 98% relative residual compressive strength), acid resistance as well as considerably lower thermal conductivity. In addition, regardless of biochar content, mortars did not exhibit flammability. Therefore, this study demonstrated that despite specific technical issues, biochar can be successfully incorporated into high dosage to cementitious composite as an alternative binder with minimum environmental impacts to improve durability and insulating performance of mortars. • Biochar was used to replace up to 20% of the cement in the paste and mortar. • Biochar increases yield stress and decreases workability of cement-based composites. • Biochar lowers mechanical properties in ambient and elevated temperature conditions. • Oven-dry density and thermal conductivity of mortars were substantially decreased. • Improved durability e.g. freeze-thaw and acid resistance was reported. [ABSTRACT FROM AUTHOR]