Search

Groundwater potential delineation in the Akka basin, southwest Morocco, has been determined through the combination of geospatial techniques and geological data. The geometric average and expected value are two multi-criteria approaches used to integrate a set of factors–data for which the weights of each factor are assigned using the fuzzy logic function, which transforms values of factors influencing groundwater presence in a range of [0, 1]. The efficiency factors used in this study are the lineament density, node density, drainage density, distance from rivers, distance from lineament, permeability, slope, topographic witness index, plan curvature, and profile curvature. Thereafter, the groundwater potential map was generated in a GIS environment. To assess and compare the efficiency of the two models, the well data existing in the basin were used to choose the most efficient model. For that reason, the prediction area (P–A) graph, the normalized density (Nd), and its weight (We) were applied to estimate the capacity of each model to predict the target area. The analysis shows that the expected value model (Nd = 1.86 and We = 0.62) is more efficient than the geometric average model (Nd = 0.96 and We = −0.04). The results of the expected value model can be used in the future planning and management of water resources in the Akka basin.

Ensuring water availability for agriculture and drinking water supply in semi-arid mountainous regions requires control of factors influencing groundwater availability. In most cases, the population draws its water needs from the alluvial aquifers close to villages that are already limited and influenced by current climatic change. In addition, the establishment of deep wells in the hard rock aquifers depletes the aquifer. Hence, understanding the factors influencing water availability is an urgent requirement. The use of geographic information system (GIS), and remote sensing (RS), together with decision-making methods like analytical hierarchy process (AHP) will be of good aid in this regard. In the Tata basin, located in SE Morocco, ten factors were used to explain the groundwater potentiality map (GWPM). Five categories of potential zones were determined: very low (8.67%), low (17.74%), moderate (46.77%), high (19.95%), and very high (6.87%). The efficiency of the AHP model is validated using the ROC curve (receiver operating characteristics) which revealed a good correlation between the high potential groundwater zones and the spatial distribution of high flow wells. Geophysical prospecting, using electrical resistivity profiles, has made it possible to propose new well sites. It corresponds to conductive resistivity zones that coincide with the intersection of hydrogeological lineaments.

Water scarcity affects all continents, with approximately 1.2 billion people living in areas where water is physically lacking. This scarcity is more accentuated in countries with an arid climate, and its impact becomes more threatening when the economy depends mainly on it. The Kingdom of Morocco, with its agricultural vocation, is one of them, especially in its southern regions. Therefore, mapping areas with high groundwater potential based on available geospatial data allows for optimizing the choice of a future well in such areas. Geometric average and fractal models were used to assess and delineate potential groundwater areas in the Tissent basin, Southeast Morocco. Eight factors, including topography, geology, hydrology, and hydrogeology, influencing the distribution of water resources was used. The formation permeability factor presents the most significant impact among the others, although it is directly related to most of them. The areas located in the central and downstream part of the basin are characterized by a high water potentiality due to increased geological formations’ permeability near the drainage system, which constitutes a recharge zone, and a low slope allowing a prolonged water-formation contact time favoring a gradual infiltration of the water towards the deep aquifers. The groundwater potential map has been edited and validated by comparing it with data from 52 wells scattered throughout the basin. The favorable potential sectors cover 15.81% of the basin’s total area. The moderate ones account for 21.36% while the unfavorable areas cover 62.83%. These results aim to provide policymakers and managers with a guide map for groundwater research and reduce hydrogeological investigation costs.

International audience; In this paper, perforation experiments were carried out and numerically modelled in order to analyze the response of 2024-T3 aluminum alloy plates under different initial temperatures T0. This alloy has a particular relevance since it is widely used as a structural component in aircrafts, but it is also interesting for other sectors of industry. A gas gun projectile launcher was used to perform impacts within initial velocities V0 from 40 m/s to 120 m/s and at temperatures varying from 293 K to 573 K. A temperature softening of the material was observed which was manifested in the reduction in the ballistic limit by 10% within the temperature range studied. Changes in the material failure mode were also observed at different test conditions. Additionally, a finite element model was developed to predict the material response at high velocities and to confirm the temperature softening that was observed experimentally. An optimization of the failure criterion resulted in a reliable model for such mild aluminum alloys. The results reported here may be used for different applications in the automotive and military sectors.

In this paper, experimental and numerical results of an aluminum alloy&rsquo, s mechanical behavior are discussed. Over a wide range of strain rates (10&minus, 4 s&minus, 1 &le, έ &le, 103 s&minus, 1) the influence of the loading impact, velocity and temperature on the dynamic response of the material was analyzed. The interface friction effect on the material&rsquo, s dynamic response is examined using a split Hopkinson pressure bar (SHPB) in a high temperature experiment using finite element analysis (FEA). The effect of different friction conditions between the specimen and the transmitted/incident bars in the SHPB system was examined using cylinder bulk specimens and cylinder plates defined with four-layer configurations. The results of these tests alongside the presented numerical simulations allow a better understanding of the phenomenon and reduces (minimizes) errors during compression tests at high and low strain rates with temperatures ranging from 21 to 300 &deg, C.

The majority of structures contain singularities that cause a high stress concentration on the root of defect which affect the mechanical properties. In this regard, it’s important to take into account that the development process of fracture phenomenon requires a physical volume of elaboration of failure process. The concept of determination of this volume forces us to defineits diameter that called the effective distance. In order to settle this issue, the current paper proposes a new method such as stress triaxiality to define the fracture process zonecaused by aU-notch in a volumetric approach that’s examined under a mixed mode I+II. The bend specimens are computed by finite element method (FEM) and the local stress distribution was calculated by the Abaqus/CAE. The study shows a credibility of the criteria (χ stress gradient and β parameter of triaxiality) to determine the effective distance along the notch. The comparison between the various values shows a good agreement.