Search

Enormous concerns focus on the high-power and wide bandwidth traveling-wave tube (TWT) for its outstanding performance. In this article, a shape-optimized staggered double-vane slow-wave structure (SWS) for terahertz (THz) sheet beam TWT is proposed. The shape-optimized staggered double-vane SWS takes the advantages of higher interaction impedance, lower transmission loss, and lower phase velocity than conventional staggered double-vane SWSs. The shape-optimized staggered double-vane SWS with 85 periods is designed, fabricated, and cold tested. The measured transmission loss of the shape-optimized staggered double-vane SWS is less than 0.79 dB/cm in the frequency range of 0.211–0.26 THz, which is in good agreement with the simulation results. Furthermore, the beam–wave interaction analysis of a sheet beam TWT with this SWS is given. The output power is predicted to be >100 W with 3-dB bandwidth of >50 GHz. The results show that the shape-optimized staggered double-vane SWS is a very promising scheme to construct a high-power and wideband THz TWT for future applications such as communication and imaging. [ABSTRACT FROM AUTHOR]

The angular log-periodic meander-line traveling wave tube (TWT) is a kind of low voltage, small-sized, high power, low cost, on chip amplifiers, and considered as a key part of the advanced communication systems, the future biomedical applications and the next electronic counter measure (ECM) instruments et al. Here, an angular log-periodic meander-line TWT is presented in this article. The angular log-periodic meander-line slow wave structure (SWS) is supported by two diamond rods. The dispersion and the impedance characteristics are analyzed in detail. In order to reduce the reflection loss, a gradual ridged waveguide is connecting the input–output standard rectangular waveguide to the meander-line SWS. The particle in cell (PIC) simulations show that the output power of the TWT can reach 55 W at 34 GHz with the operation voltage of 1800 V and the beam current of 0.2 A. The SWS is manufactured by a laser machine with Molybdenum sheet. The assembled TWT is tested and the results show that the ${S}_{{11}}$ is less than −10 dB at 30–39 GHz. The ${S}_{{21}}$ mismatch between the simulated and the measurement is discussed at the end. [ABSTRACT FROM AUTHOR]

A novel sine groove waveguide slow wave structure (SGW-SWS), originated from the sine waveguide (SW), is proposed for a wideband terahertz (THz) traveling wave tube (TWT). SGW-SWS not only has high interaction impedance in a relatively wide frequency band, but also has a wide beam tunnel. In addition, it can be fabricated using the Nano-Computer Numerical Control (CNC) milling techniques. The high-frequency simulation results show that, under the same dispersion, the passband of SGW-SWS is 23 GHz wider than that of SW-SWS, and the average interaction impedance of SGW-SWS is higher than that of SW-SWS in the whole passband. And the transverse dimension of beam tunnel is independent of the dispersion characteristics of SGW-SWS, so the beam current can be further increased by enlarging the size of beam tunnel. Moreover, the particle-in-cell (PIC) simulation results reveal that the saturated power and electronic efficiency of SGW-TWT in the frequency range of 201–260 GHz are more than 84.9 W and 2.72%, respectively, when the operating voltage is 20.8 kV and the beam current is 150 mA. [ABSTRACT FROM AUTHOR]

In this article, a novel dielectric-supported staggered dual-meander-line (DS-SDML) planar slow-wave structure (SWS) is proposed for a traveling wave tube (TWT) working at ${E}$ -band. The proposed staggered arrangement of meander-lines (MLs) leads to a stronger beam–wave interaction and achieves higher output power as compared to the symmetric arrangement. The input–output couplers have been designed by using staggered stepped double ridge waveguide, to connect the standard ${E}$ -band rectangular waveguide and the DS-SDML SWS. An attenuator and pitch tapering have been applied to the proposed SWS to suppress the unwanted frequencies and to improve the output power. Particle-in-cell (PIC) simulation results show that for an 11.8-kV, 200-mA sheet-beam, the output power can reach 283 W at 75 GHz, with a maximum gain and electronic efficiency of 34.5 dB and 11.9%, respectively. [ABSTRACT FROM AUTHOR]

A novel slow wave structure (SWS), named staggered double corrugated waveguide (SDCW), is proposed for the development of wideband high-power terahertz (THz) traveling wave tubes (TWTs). The SDCW-SWS not only has the wideband characteristic of staggered double grating (SDG) but also has the high interaction impedance characteristic of symmetrical double grating. In addition, its tunnel width is independent of the lower cutoff frequency and can be further increased. Numerical Eigen mode calculations show that, under the same dispersion, the passband of SDCW-SWS is increased by more than 10 GHz compared with SDG-SWS, and the average interaction impedance at 195 GHz is increased by about 62%. A particle-in-cell simulation analysis confirms that the average output power, saturated gain, and electron efficiency of SDCW-TWT at 195 GHz are ~110 W, ~20.34 dB, and ~5.46%, respectively, when the operating voltage is 20 kV and the beam current is 100 mA. Therefore, SDCW is a promising slow wave circuit of wideband high-power THz traveling wave amplifier. [ABSTRACT FROM AUTHOR]

Traveling wave tube (TWT) is an attractive solution for wideband and high-power sources or amplifiers in the terahertz (THz) band. In this article, a novel slow-wave structure (SWS) for TWT, named double tunnel sine waveguide (DTSW), which is based on sine waveguide (SW), is proposed. The following key technologies are adopted: 1) the rectangular holes, at which the operating mode is cutoff, are alternately opened on the sine-shaped ridges to form two electron beam tunnels and 2) the lower surface of rectangular holes is flush with the top of sine-shaped ridges. Compared with the SW-SWS, DTSW-SWS has the wider operating band and higher interaction impedance under the condition that the phase velocity of the two SWSs is at the same level. In addition, DTSW-SWS is simple in structure and easy to fabricate. The particle-in-cell simulation results reveal that DTSW-TWT has an output power of more than 202 W in the frequency range of 202–255 GHz with the maximum power of ~405 W and electron efficiency of ~9.8% at 215 GHz, under the operating voltage of 23 kV and beam current of 180 mA. Therefore, the DTSW should be considered as a promising SWS for the high-power and wideband THz traveling wave amplifier. [ABSTRACT FROM AUTHOR]

A novel helical groove rectangular waveguide slow wave structure (HGRW-SWS) which evolves from the double staggered grating waveguide (DSGW) SWS is put forward to develop the high-gain and high electron efficiency terahertz (THz) traveling wave tube (TWT). The major advantages of the HGRW SWS are the higher interaction impedance, lower ohmic loss, and lower phase velocity especially in higher frequency band compared with the DSGW SWS. The gain and electron efficiency of TWT using HGRW-SWS have been significantly improved, respectively, compared with the TWT using DSGW-SWS. [ABSTRACT FROM AUTHOR]

In this paper, a 3-D fast time-domain nonlinear algorithm (FTDNA-3-D) based on particle-in-cell method for the beam–wave interaction of the sheet beam slow wave structure (SWS) is presented. Calculation equations of the circuit electric field and the space charge electric field are given. Calculation approaches of the energy exchange and the particle mover are displayed. A simplified coupling impedance simulation approach for sheet beam SWS is indicated. The FTDNA-3-D takes the transverse electric field and the focusing magnetic field into consideration. The FTDNA-3-D could reach a high simulation speed. This novel algorithm gives a faster accurate choice for the design of sheet beam traveling-wave tube (TWT). It could be used to enhance the design efficiency of sheet beam TWT. A Ka-band staggered double vane TWT is used to verify the FTDNA-3-D. Simulation results of output power and gain versus frequency from FTDNA-3-D are compared with results from CST particle studio. The results of FTDNA-3-D are in accord with CST particle studio well. [ABSTRACT FROM AUTHOR]

To improve the output power and electron efficiency and broaden the operating bandwidth, the three-gap extended output cavity was used in the relativistic klystron to replace the single-gap output cavity. The high-frequency characteristics of the three-gap extended cavity were studied. The electron load conductance was derived and corrected based on the theory of relativity, by which a more accurate relation of electron load conductance versus transmit angle can be obtained. The characteristic impedance is three times bigger than that of the single-gap cavity under the case of the $2\pi $ mode, which can improve the M^{2}(R/Q) and the beam–wave interaction efficiency. The model of sheet beam klystron (SBK) is comprised of three-gap input cavity, two-gap first idler, three-gap second idler cavity, and three-gap output cavity. The 3-D particle-in-cell simulation results show that for a 500 kV, 1 kA, 40.134 GHz, and 20 W input power, the SBK is capable of generating an output power higher than 142 MW with the gain of 68.5 dB, maximum interaction efficiency of 28.4%, and 3-dB bandwidth of 240 MHz. [ABSTRACT FROM PUBLISHER]