Search

There is current interest in using agro-based biopolymers in industrial applications. Because cottonseed protein is abundantly available, it would be useful to explore its feasibility as a polymeric additive and possible substitute for petroleum-based materials. In this work, we studied cottonseed protein isolate as a paper additive and observed its effects on the paper’s dry and wet strength. The tensile strength of paper was found to vary with the amount of the protein applied. By application of an 11% protein solution to the paper, the dry and wet strength increased by 33 and 16% compared with the paper by itself, respectively. The combined use of cottonseed protein and an acid (acetic, adipic, aspartic, and citric acids) to promote adhesion resulted in even greater dry paper strength but not in greater wet paper strength. Thermogravimetric analysis, infrared spectroscopy, and scanning electron microscopic studies suggested that the protein interacted with acid and that both components interacted with paper fibers to produce increased strength. [ABSTRACT FROM AUTHOR]

In this study, perennial fast growth Napier grass fibers were used for pulp and papermaking. Chlorination and alkaline processes were carried out using sodium chlorite and sodium hydroxide respectively, for pulp extraction from Napier grass. Detailed chemical composition analysis of the Napier grass fibers and the extracted pulp was carried out and a comparison with other perennial grasses was made. The extracted fibers and pulp obtained from Napier grass were characterized using scanning electron microscopy and Fourier transform infrared spectroscopy. The physical, optical, and mechanical properties of Napier grass pulp handmade paper sheets produced in the laboratory were investigated by finding the opacity, brightness, tensile index, breaking length, and burst index. Handmade paper sheets made from Napier grass pulp were compared to paper made from other perennial grasses. The superior properties of paper produced from Napier grass pulp indicate the suitability of Napier grass as an alternative non-wood source for papermaking. [ABSTRACT FROM AUTHOR]

Nowadays, effect pigments are widely used in many printing industries. The colorful effects produced by light scattering of these types of pigments add an additional value to the prints and enhances the overall quality of color appearance. The aim of this study was to investigate the quality enhancement of printed specialty papers with various effect pigments in combination with offset inks. Four different effect pigments were used (one luster pigment-EP1, two interference pigments-EP2, EP3, and one multicolor pigment-EP4) as well as two types of paper substrates (film synthetic paper and wood-free paper). The effect pigments were overprinted on dried CMYK offset prints on both paper substrates. The following analysis were performed: scanning electron microscopy analysis of effect pigment particles, contact angles of papers and offset prints, Fourier transform infrared spectrocopy (FTIR), principal components analysis (principal components analysis (PCA)), and flop index analysis of overprinted effect pigments, and paper and print gloss. The results of the experiment indicate that effect pigments behaved differently on different printing substrates. From the FTIR and PCA, it was found that the different composition of effect pigments differently influence the behavior of these particles on the final prints. Effect pigments overprinted on offset CMYK inks on both paper substrates enhance print gloss, except interference pigment EP2 on film synthetic paper. It was also found that the ink color has the most pronounced influence on flop index, followed by the papertype and the type of effect pigment. Higher flop index was obtained at wood-free paper, especially by overprinted pigment EP2. © 2012 Wiley Periodicals, Inc. Col Res Appl, 38, 168-176, 2013. [ABSTRACT FROM AUTHOR]

Conductive paper was prepared via in situ chemical oxidative polymerization of 3,4-ethylenedioxythiophene (EDOT) in pulp suspension by using iron(III) p-toluenesulfonate (Fe(OTs)3) as both an oxidant and a dopant source. The deposition of poly(3,4-ethylenedioxythiophene) (PEDOT) on the pulp fiber surface was verified and characterized by ATR-FTIR and SEM analyses. The factors affecting the conductivity of the PEDOT-coated paper were investigated, and the preparation conditions of the conductive paper with a low resistivity and excellent environmental stability was obtained. The optimum reaction temperature and time were 60 °C and 4 h, respectively. The molar ratio of EDOT to Fe(OTs)3 of 1:1 was optimal when considering both cost and performance factors. The conductivity of the PEDOT-coated paper could be controlled by adjusting EDOT concentration. The threshold concentration of EDOT was about 3 g⋅L-1, and a volume resistivity as low as 5.9x10³ Ω⋅cm could be achieved, which reached the conductivity range of an electrical conductor. The environmental stability of the PEDOT-coated conductive paper was very good due to the much higher oxidation potential of PEDOT. [ABSTRACT FROM AUTHOR]