Search

A technology is developed for manufacturing planar microfluidic chips (MFCs) based on Silgard 8040, encompassing template fabrication, mold production, sealing, and adsorbent filling. These MFCs, filled with a Porapak-Q adsorbent, facilitate sample preparation and calibration under uniform conditions, integrating both sample collection and preconcentration stages. Experimental investigations have identified optimal conditions for acetone preconcentration using Silgard 8040-based MFCs, achieving a maximum concentration factor of 43 at adsorption temperature (Tads) of 0°C, desorption temperature (Tdes) of 70°C, adsorption volume (Vads) of 45 mL, and desorption time (tdes) of 1 s. The feasibility of using MFCs for sample collection and preparation, taking into account sample storage time, has been evaluated. The procedure maintains accuracy within 6–10% over 8 h without a necessity for additional drying of the collected samples from exhaled air. [ABSTRACT FROM AUTHOR]

Gold nanoparticles (AuNPs) have emerged as promising agents in biomedical applications due to their unique physicochemical properties. This study investigates the cellular interactions of AuNPs with A549 (non-small cell lung adenocarcinoma) and BEAS-2B (normal bronchial epithelial) cell lines. AuNPs were synthesized via the citrate reduction method, resulting in 20, 50, and 70 nm particles. Cells were incubated with AuNPs for increasing durations (30 minutes, 4 hours, and 24 hours). Post-incubation, cells were washed with PBS, air-fixed, and subsequently analyzed using Atomic Force Microscopy (AFM) to obtain detailed topographical maps. AFM imaging revealed distinct interactions between AuNPs and the two cell lines. A549 cells displayed darker regions on the cell surface, indicative of topographical depressions likely resulting from nanoparticle-induced membrane collapse. In contrast, BEAS-2B cells did not exhibit such depressions, which is consistent with the literature that suggests cancer cells are mechanically softer than normal cells. The surface roughness analysis results indicated that the preservation of surface integrity post-fixation validates the air-fixation methodology for obtaining reliable mechanical data from AFM analyses. [ABSTRACT FROM AUTHOR]

Although not expected to be used due to restrictions raised on their usage, Persisted Organic Pollutants (POP) such as organochlorinated pesticides (OCPs) can be found in several matrices, even nowadays. The lack of biodegradation and, furthermore, their persistence in the environment result in the possible occurrence of these lipophilic toxins in several matrices, from environmental samples and foods to human milk. The current review focuses on the usage of hyphenated techniques for the determination and monitoring of OCPs in several matrices, such as milk—both animal and human milk. The lipid matrix of milk and dairy products favors the possible bioaccumulation of the above pollutants, and the complex matrix of the dairy products is a challenge for method development. Additionally, spectroscopic methods—mainly Nuclear Magnetic Resonance (NMR)-based metabolomics—for biomonitoring of OCPs persistence, bioaccumulation, and effect of possible exposure, along with NMR usage in several methods developed, are also presented and discussed. Finally, we introduce and present the metabolomic approach for OCPs and other POPs in lipid matrices. [ABSTRACT FROM AUTHOR]

Scrub typhus is caused by the Gram-negative obligate intracellular bacterium Orientia tsutsugamushi, and this tick-borne disease is difficult to distinguish from other acute febrile illnesses as it typically presents with symptoms such as rash, crusting at the bite site, headache, myalgia, lymphadenopathy, and elevated liver transaminases. It can often be diagnosed clinically, but not all patients present with characteristic symptoms, so serological diagnosis and molecular techniques may be required. However, existing diagnostic tests often have low sensitivity and specificity, making early detection difficult. This study presents a nucleic acid extraction method using large volumes of plasma and buffy coat to increase sensitivity, as well as an improved detection method using two target genes. Using the I-PULL device, nucleic acids can be extracted from up to 4 mL of sample in 30 min, avoiding contamination. The extracted DNA detects two genes of O. tsutsugamushi, increasing sensitivity compared to single-gene detection. Clinical validation in 38 patient samples showed 100% specificity and 95.24% sensitivity for the single target gene, with specificity and sensitivity rising to 100% when both genes are analyzed. This molecular diagnostic platform can be useful for distinguishing scrub typhus from similar diseases. [ABSTRACT FROM AUTHOR]

Pesticide residues in human diets pose significant health hazards, particularly for vulnerable populations such as infants and children. This study aimed to determine pesticide residues in apples and to assess the cumulatively chronic risk posed to adult and child consumers from simultaneous exposure to multiple residues. During the 2022–2023 harvest seasons, 100 apple samples from Turkey were analyzed for the presence of 225 different pesticide residues. Pesticide extraction was performed using the QuEChERS method, followed by detection through liquid chromatography coupled with tandem mass spectrometry. Fifteen distinct pesticides (ten insecticides and five fungicides) were detected in 64 out of the 100 apple samples analyzed. Eleven samples contained pesticide residues that exceeded the maximum residue limit (MRL) set by the Turkish Food Codex and the European Union. Thiophanate-methyl was the most frequently detected pesticide (34%) in apples, with concentrations ranging from 0.012 to 0.108 mg kg−1, all of which were well below the MRL of 0.5 mg kg−1. Other commonly detected residues included chlorantraniliprole (28%), acetamiprid (24%), sulfoxaflor (22%), bifenazate (18%), indoxacarb (13%), diflubenzuron (12%), and carbendazim (10%). Under a worst-case scenario, the hazard index (HI) values for adults and children were 0.85% and 2.60%, respectively, indicating that these values remain significantly below the risk threshold of 100%, suggesting no associated health risks from apple consumption. However, regular monitoring of pesticide residues in fresh fruits and vegetables remains critically important. [ABSTRACT FROM AUTHOR]

Food allergens in processed foods are affected by heating, processing, and the food matrix. To conduct highly reliable tests, extracting allergens into test solutions is necessary for appropriate detection. In addition to the commonly used enzyme-linked immunosorbent assay (ELISA), liquid chromatography-mass spectrometry (LC–MS), which has the advantage of simultaneously detecting multiple allergens in foods, is being increasingly used. When managing food allergens at food manufacturing sites, obtaining the same measured values is desirable, regardless of the analytical method used. Therefore, in this study, we focused on the importance of pretreatment steps for LC–MS when examining food allergens in processed foods, which can be difficult to analyze. The ELISA method uses food extracts optimized for analyzing allergens in processed foods. We developed a high-resolution accurate mass spectrometry (HRAM)-LC–MS/MS method using the same food extract used in the ELISA method and an MS sample preparation kit. Multiple food allergen analysis was performed using 1, 5, 10, and 20 ppm of allergen-incurred processed foods. Overall, a strong correlation was observed between the measured values of HRAM-LC–MS/MS and ELISA, demonstrating the applicability of multi-allergen analysis using LC–MS. [ABSTRACT FROM AUTHOR]

Ricin is a toxic protein regarded as a potential chemical weapon for bioterrorism or criminal use. In the event of a ricin incident, rapid analytical methods are essential for ricin confirmation in a diversity of matrices, from environmental to human or food samples. Mass spectrometry–based methods provide specific toxin identification but require prior enrichment by antibodies to reach trace-level detection in matrices. Here, we describe a novel assay using the glycoprotein asialofetuin as an alternative to antibodies for ricin enrichment, combined with the specific detection of signature peptides by high-resolution mass spectrometry. Additionally, optimizations made to the assay reduced the sample preparation time from 5 h to 80 min only. Method evaluation confirmed the detection of ricin at trace levels over a wide range of pH and in protein-rich samples, illustrating challenging matrices. This new method constitutes a relevant antibody-free solution for the fast and specific mass spectrometry detection of ricin in the situation of a suspected toxin incident, complementary to active ricin determination by adenine release assays. [ABSTRACT FROM AUTHOR]

Despite advancements in the sensitivity and performance of analytical instruments, sample preparation remains a bottleneck in the analytical process. Currently, solid-phase extraction is more widely used than traditional organic solvent extraction due to its ease of use and lower solvent requirements. Moreover, various microextraction techniques such as micro solid-phase extraction, dispersive micro solid-phase extraction, solid-phase microextraction, stir bar sorptive extraction, liquid-phase microextraction, and magnetic bead extraction have been developed to minimize sample size, reduce solvent usage, and enable automation. Among these, in-tube solid-phase microextraction (IT-SPME) using capillaries as extraction devices has gained attention as an advanced "green extraction technique" that combines miniaturization, on-line automation, and reduced solvent consumption. Capillary tubes in IT-SPME are categorized into configurations: inner-wall-coated, particle-packed, fiber-packed, and rod monolith, operating either in a draw/eject system or a flow-through system. Additionally, the developments of novel adsorbents such as monoliths, ionic liquids, restricted-access materials, molecularly imprinted polymers (MIPs), graphene, carbon nanotubes, inorganic nanoparticles, and organometallic frameworks have improved extraction efficiency and selectivity. MIPs, in particular, are stable, custom-made polymers with molecular recognition capabilities formed during synthesis, making them exceptional "smart adsorbents" for selective sample preparation. The MIP fabrication process involves three main stages: pre-arrangement for recognition capability, polymerization, and template removal. After forming the template-monomer complex, polymerization creates a polymer network where the template molecules are anchored, and the final step involves removing the template to produce an MIP with cavities complementary to the template molecules. This review is the first paper to focus on advanced MIP-based IT-SPME, which integrates the selectivity of MIPs into efficient IT-SPME, and summarizes its recent developments and applications. [ABSTRACT FROM AUTHOR]

The escalating impact and remarkable progress of nanotechnology have shifted the paradigms of medicine and the healthcare system. Nanosystems have emerged, extensively holding the potential to advance disease diagnosis and treatment specificity. The extraordinary attributes imparted by nano-systems have helped in overcoming the limitations of conventional interventions to an extent and led to targeted therapy, to name one. The role of nanotechnology in diagnosis is another breakthrough in its appellation. This article aims to address the current characterization and sample preparation techniques for the analysis of nanosystems and provide insights into novel methodologies and in situ instrumentation that have eased sampling procedures. [ABSTRACT FROM AUTHOR]

Coloring agents in foods and drinks have been popular for centuries. This study aims to analyze the presence of ten synthetic colors (namely, (allura red (E129), amaranth (E123), sunset yellow (E110), tetrazine (E102), fast green (E143), ponceau 4R (New Coccine) (E124), erythrosin B (E127), brilliant blue FCF (E133), brilliant black (E151) and carmoisine (E122))) in food and drink samples using ultra-high-performance liquid chromatography diode array detection (UHPLC-DAD). The present analytical method was carried out using Agilent Poroshell 120 HPH-C18 column, 3 × 100 mm, 2.7 µm, and a mobile phase consisting of 10 mM Na2HPO4, pH 7, mixed with methanol as a time-increment gradient solution until the time was 20 min, then decreased with time until the time was 26 min. The pH was set by orthophosphoric acid at 7 and 5 μL injection volume, 0.50 mL flow rate, and the elution systems were monitored at 428 nm for E102, 518 nm for E124, E110, E129, E122, 530 nm for E151, E127, 622 nm for E143, and E133, respectively. The limit of detection and quantification for all colors ranged from 0.017 to 0.025 and 0.057 and 0.082 mg L−1, respectively. The correlation coefficient values ranged between 0.9991 and 1.0. The selectivity of the assay revealed no interference from other components in the analyzed samples. The percent recovery and precision (intra- and inter-day) of the spiked samples were within the acceptable limits of the ICH guidelines. Five analytical parameters were employed, and the results showed a new, novel, and robust method according to ICH guidelines for analyzing these colors. While most of the investigated food and drinks fell within the accepted range, some fell outside. The current sample preparation and analytical methods are comprehensive and universal for extracting and measuring synthetic colors in various food and drink samples. [ABSTRACT FROM AUTHOR]

The escalating impact and remarkable progress of nanotechnology have shifted the paradigms of medicine and the healthcare system. Nanosystems have emerged, extensively holding the potential to advance disease diagnosis and treatment specificity. The extraordinary attributes imparted by nano-systems have helped in overcoming the limitations of conventional interventions to an extent and led to targeted therapy, to name one. The role of nanotechnology in diagnosis is another breakthrough in its appellation. This article aims to address the current characterization and sample preparation techniques for the analysis of nanosystems and provide insights into novel methodologies and in situ instrumentation that have eased sampling procedures.

INTRODUCTION. Metaphase analysis is used to assess the mutagenicity of medicines, and its accuracy depends directly on the quality of cytogenetic preparations. Existing procedures for cytogenetic sample preparation require optimisation because of their time and labour intensiveness and potential for artefactual chromosome loss that leads to errors in the interpretation of analytical results.AIM. This study aimed to optimise a cytogenetic sample preparation procedure for mammalian bone marrow cells for in vivo metaphase analysis.MATERIALS AND METHODS. The study was performed in randomly bred male mice weighing 18–20 g. The authors prepared cytogenetic samples of bone marrow cells according to the procedures set forth in the Guidelines for Conducting Preclinical Studies of Drugs (A.N. Mironov (ed.), 2012), and GOST 34659-2020, Methods for Testing the Impact of Chemical Products on the Human Body. Assessment of Chromosomal Aberrations in Bone Marrow Cells of Mammals, as described and with modifications. Sample preparation involved using Hanks’ solution, sodium citrate and potassium chloride solutions, acetic acid, methyl alcohol, medium 199, HEPES, and Giemsa stain.RESULTS. The authors conducted an experimental comparison of the characteristics of cytogenetic preparations of mammalian bone marrow cells for in vivo metaphase analysis prepared using several methods. The samples prepared in accordance with the Guidelines for Conducting Preclinical Studies of Drugs exhibited the highest percentage of analysable metaphase plates, in comparison with those obtained using the other sample preparation procedures. The authors optimised the sample prepara tion conditions, including the composition of the hypotonic solution (0.56% KCl), the time of hypotonic treatment (20 min), the time of fixation (12 h), and the composition of the culture medium (liquid medium 199 with Hanks’ salts and glutamine). The authors introduced a step of preliminary chromosome fixation with 6% acetic acid, which generally contributed to an increase in the proportion of analysable metaphase plates by reducing the scattering and sticking of chromosomes. CONCLUSIONS. The authors presented a modified sample preparation procedure for cytogenetic preparations that, compared with the previous procedures, offers an increase in the percentage of analysable metaphase plates to 56%, a 12% rise in the percentage of full sets of chromosomes (n=40), and a 2–10-hour reduction in the preparation time.

Abstract Mass spectrometry has revolutionized cell signaling research by vastly simplifying the analysis of many thousands of phosphorylation sites in the human proteome. Defining the cellular response to perturbations is crucial for further illuminating the functionality of the phosphoproteome. Here we describe µPhos (‘microPhos’), an accessible phosphoproteomics platform that permits phosphopeptide enrichment from 96-well cell culture and small tissue amounts in 90% selectivity, and excellent quantitative reproducibility. Employing highly sensitive trapped ion mobility mass spectrometry, we quantify ~17,000 Class I phosphosites in a human cancer cell line using 20 µg starting material, and confidently localize ~6200 phosphosites from 1 µg. This depth covers key signaling pathways, rendering sample-limited applications and perturbation experiments with hundreds of samples viable. We employ µPhos to study drug- and time-dependent response signatures in a leukemia cell line, and by quantifying 30,000 Class I phosphosites in the mouse brain we reveal distinct spatial kinase activities in subregions of the hippocampal formation.

Among the various compounds regarded as emerging contaminants (ECs), pharmaceuticals and personal care products (PPCPs) are of particular concern. Their continuous release into the environment has a negative global impact on human life. This review summarizes the sources, occurrence, persistence, consequences of exposure, and toxicity of PPCPs, and evaluates the various analytical methods used in the identification and quantification of PPCPs in a variety of solid and liquid environmental matrices. The current techniques of choice for the analysis of PPCPs are state-of-the-art liquid chromatography coupled to mass spectrometry (LC-MS) or tandem mass spectrometry (LC-MS2). However, the complexity of the environmental matrices and the trace levels of micropollutants necessitate the use of advanced sample treatments before these instrumental analyses. Solid-phase extraction (SPE) with different sorbents is now the predominant method used for the extraction of PPCPs from environmental samples. This review also addresses the ongoing analytical method challenges, including sample clean-up and matrix effects, focusing on the occurrence, sample preparation, and analytical methods presently available for the determination of environmental residues of PPCPs. Continuous development of innovative analytical methods is essential for overcoming existing limitations and ensuring the consistency and diversity of analytical methods used in investigations of environmental multi-class compounds. [ABSTRACT FROM AUTHOR]

Preparation of biomacromolecules for structural biology studies is a complex and time‐consuming process. The goal is to produce a highly concentrated, highly pure product that is often shipped to large facilities with tools to prepare the samples for crystallization trials or for measurements at synchrotrons and cryoEM centers. The aim of this article is to provide guidance and to discuss general considerations for shipping biomacromolecular samples. Details are also provided about shipping samples for specific experiment types, including solution‐ and cryogenic‐based techniques. These guidelines are provided with the hope that the time and energy invested in sample preparation is not lost due to shipping logistics. [ABSTRACT FROM AUTHOR]

Mass spectrometry has revolutionized cell signaling research by vastly simplifying the analysis of many thousands of phosphorylation sites in the human proteome. Defining the cellular response to perturbations is crucial for further illuminating the functionality of the phosphoproteome. Here we describe µPhos ('microPhos'), an accessible phosphoproteomics platform that permits phosphopeptide enrichment from 96-well cell culture and small tissue amounts in <8 h total processing time. By greatly minimizing transfer steps and liquid volumes, we demonstrate increased sensitivity, >90% selectivity, and excellent quantitative reproducibility. Employing highly sensitive trapped ion mobility mass spectrometry, we quantify ~17,000 Class I phosphosites in a human cancer cell line using 20 µg starting material, and confidently localize ~6200 phosphosites from 1 µg. This depth covers key signaling pathways, rendering sample-limited applications and perturbation experiments with hundreds of samples viable. We employ µPhos to study drug- and time-dependent response signatures in a leukemia cell line, and by quantifying 30,000 Class I phosphosites in the mouse brain we reveal distinct spatial kinase activities in subregions of the hippocampal formation. Synopsis: The study introduces µPhos, an accessible, plate-based workflow for low-input mass spectrometry-based phosphoproteomics. µPhos greatly facilitates high-dimensional experimental designs, as demonstrated by a 96-well drug response screen and analysis of small anatomical regions in the mouse brain. Systematic optimization results in sensitive and selective enrichment of phosphopeptides in <100 µL, allowing direct processing of 96-well plates within one working day. µPhos combined with dia-PASEF reproducibly quantifies 6000 to 17,000 confidently localized phosphosites from 1 to 20 µg protein starting material. Sub-region resolved analysis of the mouse brain phosphoproteome infers spatially distinct kinase activity. Time-course analysis of chronic myeloid leukemia cells treated with tyrosine kinase inhibitors reveals drug-specific responses. The study introduces µPhos, an accessible, plate-based workflow for low-input mass spectrometry-based phosphoproteomics. µPhos greatly facilitates high-dimensional experimental designs, as demonstrated by a 96-well drug response screen and analysis of small anatomical regions in the mouse brain. [ABSTRACT FROM AUTHOR]

Microplastics (MP) are omnipresent in a wide range of environments, constituting a potential threat for aquatic and terrestrial wildlife. Effects in consumers range from physical injuries to pathological reactions. Due to potential bioaccumulation of MP, predators are of particular concern for MP induced health effects. The Eurasian otter is an apex predator in (semi-)aquatic habitats feeding primarily on fish. Furthermore, the species is classified as "near threatened" on the IUCN Red List. Thus, the Eurasian otter is of conservation concern and may serve as a bioindicator for MP pollution. Feces can be used to detect pollutants, including MP. Initial studies confirmed the presence of MP in otter feces (= spraints). However, as specific, validated protocols targeting at an efficient and standardized extraction of MP from otter spraints are missing, experimental results reported from different groups are challenging to compare. Therefore, we (i) present steps towards a standardized protocol for the extraction of MP from otter feces, (ii) give recommendations for field sample collection of otter spraints, and (iii) provide a user-friendly step-by-step workflow for MP extraction and analysis. Applying this framework to field samples from five study sites along the River Inn (n = 50), we detected MP of different sizes and shapes (ranging from microfibers to road abrasion and tire wear) in all otter spraint samples. [ABSTRACT FROM AUTHOR]

The measurement uncertainty (MU) in environmental analyses is usually considered as a combination of the additive contributions from sampling, sample preparation and analytical measurement (usually instrumental). The target MU for such studies is usually relatively high due to the natural sample heterogeneity and/or the complicated pretreatment procedure required. In the analytical practice, the contribution of the sample preparation to MU is rarely evaluated. Thus, it remains a hidden part of the one related to the analysis. However, the knowledge for the contribution of sample preparation might provide important information and further possibility for optimization of the entire analytical procedure and reduction of the expanded MU of the analytical result. From statistical point of view, the separation of uncertainty contributions from the different steps is, generally, not a trivial task. Selection of the proper statistical approach depends on the data structure and quality, variables distribution, etc. In the present study, three different statistical methods for evaluation of the uncertainty contribution of the sample preparation were applied, compared, and discussed. The considered approaches are based on, both, classical and robust analysis of variances (ANOVA) applied to data from instrumental analysis of marine algae and bee honey samples, undergoing microwave digestion. Some general recommendations on the statistical approach selection are revealed based on real experimental data set. [ABSTRACT FROM AUTHOR]

The exposure of humans to microplastics through food is a topic of great interest. Foods of marine origin, such as fish and salt, have been the most extensively studied in this regard. Conversely, foods considered less likely to be contaminated (such as dairy products) have been investigated to a lesser extent. This is the first study addressing the occurrence of microplastics in cheese. In this paper, we report the first analytical approach for cheese preparation, before a chemical analysis of microplastics in cheese was performed. Therefore, the most suitable digestion methods were investigated. Alkaline digestion (i.e., KOH 5 M, 50 °C, 48 h) achieved a digestion efficiency of 97.5 ± 0.8%. To assess the feasibility of the preparative method proposed, a recovery rate of spiked polystyrene microbeads (~10 µm) of 98.5 ± 0.4% was determined. Further, the effects of the digestion agent on the microbeads were also investigated. To confirm whether the preparative method allows for the confirmation of the plastic-nature of microparticles, a qualification of spiked microplastics (polystyrene, 150 µm, and polyethylene terephthalate, 300 µm) was performed using pyrolysis–gas chromatography–mass spectrometry. [ABSTRACT FROM AUTHOR]

Soil is one of the main destinations for pesticides and veterinary drugs used in agriculture and animal production. The negative consequences of the accumulation of these compounds in the environment make it important to monitor these compounds in the soil. In this study, we compared different extraction procedures using solvent shaking, ultrasound, or QuEChERS, and their combinations, for the simultaneous determination of 75 pesticide and seven veterinary drug residues in agricultural soil by ultra-high performance liquid chromatography coupled to serial mass spectrometry (UHPLC–MS/MS). The method using QuEChERS combined with shaking showed the best results for soil using the addition of water, followed by extraction with acetonitrile acidified with acetic acid and shaking in a shaker. For partitioning, anhydrous magnesium sulfate and anhydrous sodium acetate were used. The extract was centrifuged, filtered, and diluted (1:4, v/v) in water for determination by UHPLC–MS/MS. Method validation showed adequate accuracy and precision results, with recoveries between 70 and 120% and RSD ≤ 20% for the vast majority of the compounds evaluated at the spike levels of 10, 25, 50, and 100 μg kg−1. The method limits of detection (LOD) and quantification (LOQ) ranged from 3.0 to 7.5 μg kg−1 and from 10 to 25 μg kg−1, respectively. The method was applied to different agricultural soil samples and proved to be efficient for routine analysis. [ABSTRACT FROM AUTHOR]

Accurate measurement of steroid hormones is crucial to elucidate new mechanisms of action and diagnose steroid metabolism-related diseases. This study presents a simple, sensitive, and automated analytical method for nine representative steroid hormones. The method involves on-line coupling of in-tube solid-phase microextraction (IT-SPME) with liquid chromatography–tandem mass spectrometry (LC–MS/MS). The steroid hormones were extracted and enriched on a Supel-Q PLOT capillary column using IT-SPME. Subsequently, they were separated and detected within 6 min using a Discovery HS F5-3 column and positive ion mode multiple reaction monitoring system via LC–MS/MS. Calibration curves of these compounds using each stable isotope-labeled internal standard (IS) showed linearity with correlation coefficients greater than 0.9990 in the range of 0.01–40 ng/mL, with limits of detection (S/N = 3) of 0.7–21 pg/mL. Moreover, intra- and inter-day variations were lower than 8.1 and 15% (n = 6), respectively. The recoveries of these compounds from saliva samples were in the range of 82–114%. The developed IT-SPME/LC–MS/MS method of steroid hormones is a highly sensitive, specific, and non-invasive analytical method that allows extraction and enrichment with no organic solvents, and enables direct automated online analysis by simply ultrafiltrating a small sample of saliva. [ABSTRACT FROM AUTHOR]

The European Union's recent decision to renew the authorization for the use of glyphosate until 15 December 2033 has stimulated scientific discussion all around the world regarding its toxicity or otherwise for humans. Glyphosate is a chemical of which millions of tons have been used in the last 50 years worldwide to dry out weeds in cultivated fields and greenhouses and on roadsides. Concern has been raised in many areas about its possible presence in the food chain and its consequent adverse effects on health. Both aspects that argue in favor of toxicity and those that instead may indicate limited toxicity of glyphosate are discussed here. The widespread debate that has been generated requires further investigations and field measurements to understand glyphosate's fate once dispersed in the environment and its concentration in the food chain. Hence, there is a need for validated analytical methods that are available to analysts in the field. In the present review, methods for the analytical determination of glyphosate and its main metabolite, AMPA, are discussed, with a specific focus on chromatographic techniques applied to cereal products. The experimental procedures are explained in detail, including the cleanup, derivatization, and instrumental conditions, to give the laboratories involved enough information to proceed with the implementation of this line of analysis. The prevalent chromatographic methods used are LC-MS/MS, GC-MS/SIM, and GC-MS/MS, but sufficient indications are also given to those laboratories that wish to use the better performing high-resolution MS or the simpler HPLC-FLD, HPLC-UV, GC-NPD, and GC-FPD techniques for screening purposes. The concentrations of glyphosate from the literature measured in wheat, corn, barley, rye, oats, soybean, and cereal-based foods are reported, together with its regulatory status in various parts of the world and its accumulation mechanism. As for its accumulation in cereals, the available data show that glyphosate tends to accumulate more in wholemeal flours than in refined ones, that its concentration in the product strictly depends on the treatment period (the closer it is to the time of harvesting, the higher the concentration), and that in cold climates, the herbicide tends to persist in the soil for a long time. [ABSTRACT FROM AUTHOR]

Polycyclic aromatic hydrocarbons are considered to be potentially genotoxic and carcinogenic to humans. For non-smoking populations, food is the main source of polycyclic aromatic hydrocarbons exposure. Due to their lipophilic nature, oils and fats rank among the food items with the highest polycyclic aromatic hydrocarbon content. Consequently, the detection of polycyclic aromatic hydrocarbons in edible oils is critical for the promotion of human health. This paper reviews sample pretreatment methods, such as liquid-phase-based extraction methods, adsorbent-based extraction methods, and the QuEChERS (quick, easy, cheap, effective, rugged, and safe) method, combined with detection techniques like mass spectrometry and chromatography-based techniques for accurate quantification of polycyclic aromatic hydrocarbons in edible oils since 2010. An overview on the advances of the methods discussed herein, along with a commentary addition of current challenges and prospects, will guide researchers to focus on developing more effective detection methods and control measures to reduce the potential risks and hazards posed by polycyclic aromatic hydrocarbons. [ABSTRACT FROM AUTHOR]

Effective pathogen detection is essential for plant disease control. However, plant sample preparation for downstream assays, such as quantitative polymerase chain reaction (qPCR), is challenging to perform outside of a laboratory. This paper reports two sample preparation methods featuring chemical and mechanical lysis and nucleic acid extraction using a micro-homogenizer, followed by serial dilution or nucleic acid purification with a paper disk before assay. Five minutes of lysis and extraction resulted in DNA and RNA yields of up to 76.5% and 63.3%, respectively, compared to mortar and pestle controls. Crude lysates were unsuitable for direct use in qPCR assays; however, serial dilution or quick wash using chromatography paper rendered samples ready for such assays. Additionally, the nucleic acids stored on paper disks under various storage conditions remained stable for one month. These methods can facilitate the in-field preparation of citrus samples and allow for both onsite and mail-in diagnostics for growers. [ABSTRACT FROM AUTHOR]

Suitable sample collection and preparation methods are essential to enable nucleic acid amplification testing at the point of care (POC). Strategies that allow direct isothermal nucleic acid amplification testing (iNAAT) of crude sample lysate without the need for nucleic acid extraction minimize time to result as well as the need for operator expertise and costly infrastructure. The authors review research to understand how sample matrix and preparation affect the design and performance of POC iNAATs. They focus on approaches where samples are directly combined with liquid reagents for preparation and amplification via iNAAT strategies. They review factors related to the type and method of sample collection, storage buffers, and lysis strategies. Finally, they discuss RNA targets and relevant regulatory considerations. Limitations in sample preparation methods are a significant technical barrier preventing implementation of nucleic acid testing at the POC. The authors propose a framework for co-designing sample preparation and amplification steps for optimal performance with an extraction-free paradigm by considering a sample matrix and lytic strategy prior to an amplification assay and readout. In the next 5 years, the authors anticipate increasing priority on the co-design of sample preparation and iNAATs. [ABSTRACT FROM AUTHOR]

Cryptosporidium is a cause of diarrheal infections responsible for a loss of human and animal welfare worldwide. The impact of the parasite is underestimated and the reported sources of infection are diverse, as it occurs in a wide variety of hosts. Wildlife has been reported as a notifiable source, but few studies are available on its occurrence in European wild boar and cervid species. To determine the occurrence of Cryptosporidium in game in Brandenburg, Germany, a molecular survey was conducted during the 2017 to 2020 hunting seasons. A total of 562 fecal samples from wild boar (Sus scrofa, n = 262), roe deer (Capreolus capreolus, n = 174), red deer (Cervus elaphus, n = 62), fallow deer (Dama, n = 51) and 13 samples of unspecified species were analyzed for both 18S ribosomal RNA (18S rRNA) and Cryptosporidium oocyst wall protein (COWP) gene sequence regions. PCR results showed that 21.2 % of the samples (n = 119/562) were positive for at least one target gene (18S rRNA: n = 114; COWP: n = 14), but differences in Cryptosporidium occurrence were observed within species and hunting seasons, with variations ranging from 1.8 % to 41.7 % (roe deer), respectively. Analysis of Sanger sequences of the 18S rRNA and COWP PCR products indicated that the C. sp. deer genotype was predominant in deer (roe deer: 86.7 %, red deer: 66.7 %, fallow deer: 58.8 %), while C. suis and C. scrofarum were mainly detected in wild boar (88.5 %). The human pathogenic species C. parvum was detected in only 1.2 % (n = 7) of the samples analyzed, but without a clear indication of a specific wild animal host. The highest Cryptosporidium diversity was found in wild boar and roe deer with five and four different species, respectively. Comparison of the 18S rRNA sequences with the designated reference revealed minor variations at several nucleotide positions in some isolates, possibly indicating evolutionary adaptations and the development of new subtypes. In conclusion, wildlife represents a reservoir for a diverse spectrum of Cryptosporidium species and may thus contribute to their environmental spread and the transmission to humans.

Phytosterols (PSs) are bioactive compounds in the sterol family, present in numerous complex food and plant matrices in free and conjugated forms. The interest in these compounds arises for phytotherapeutic purposes, particularly for their action on cholesterol metabolism and impact on cardiovascular diseases. There is a need to develop approaches that can selectively extract target analytes and accurately identify and quantify them with high precision. This work proposed the synthesis of molecularly imprinted polymers (MIPs) for PSs with a sonochemical approach, enabling a rapid polymerization step (5 min). This proposed MIP was able to extract 8 PSs (brassicasterol, stigmastanol, campesterol, campestanol, stigmasterol, β-sitosterol, Δ5-avenasterol, α-spinasterol) from a wide range of plant and food matrices belonging to different classes (Brassicaceae, dried fruits and Leguminosae) and was coupled to ultra-high liquid chromatography with tandem mass spectrometry (UHPLC-MS/MS). MIP based on dispersed solid phase extraction (dSPE-MIP) and targeted analysis has proven to be particularly effective in addressing the challenges associated with the complexity of plant-derived matrices, minimising interferences. This was demonstrated by the excellent control of the matrix effect, which was within ±15 %, ensuring the robustness and reliability of the method. The identification and quantification of 8 different PSs was successfully achieved with satisfactory recovery values ranging from 65 % to 100 %. The proposed strategy offers an affordable alternative to classical methods, providing enhanced sensitivity, selectivity and overall performance.

Food analysis plays an important role in preserving the integrity and quality of food. Despite these noble goals, most official methods for the analysis of nutrients (vitamins, carotenoids, etc.) antioxidants (polyphenols, etc.), and contaminants (pesticides, veterinary drugs, mycotoxins etc.) still rely on time-consuming, complex, and polluting procedures of sample preparation. To solve this discrepancy, the scientific community has frantically been working to make extraction procedures faster and safer, resorting to miniaturization, automation, low-energy consumption, and solvents/sorbents from renewable resources. This review provides an overview of the most sustainable extraction methods in food analysis, developed over the last ten years (2014–2024), including relevant examples of both liquid phase and sorbent-based techniques. Particular emphasis is placed on solutions aimed at improving the method sustainability such as smart devices, neoteric solvents, and composite sorbents, discussing the latest advancements and future trends in this sector.

A new derivatization reagent, phthalylglycyl chloride (PG-Cl), for the analysis of urinary amino acids was demonstrated using reversed-phase ultra-high performance liquid chromatography coupled to electrospray ionization-quadrupole-time-of-flight mass spectrometer. The study compares the limits of detection and quantification for different sample preparation techniques with the commonly used and effective method of derivatization using dansyl chloride. The stability of the derivatives was investigated, and the study includes an example of urinary amino acid analysis using PG-Cl derivatization. The optimal values for pH, temperature, and concentration of the derivatization reagent were established. Limits of quantification in the range of 0.5–500 µg/mL were obtained for different amino acids. The possibility of phthalylglycyl chloride usage for non-target screening applications and targeted analysis of amino acids in urine was discussed. An advantages and issues of PG-Cl in comparison with commonly used acyl-chlorides (FMOC-Cl and DNS-Cl) provided and discussed.

Solid-phase analytical derivatization is a versatile sample preparation technique that enhances analysis accuracy, efficiency, reproducibility, and sensitivity. The technique combines the advantages of analytical derivatization and solid-phase extraction, providing a versatile approach for analysing analytes with various functional groups in complex matrices. Analytical derivatization is a technique used for functional group analysis that involves modifying the structure of an analyte to enhance sensitivity and specificity. Solid-phase analytical derivatization is a one-pot procedure that combines analytical derivatization and extraction. In the presence of acids, it can derivatize phenols, carboxylic acids, and other analytes. Furthermore, solid-phase analytical derivatization increases the reaction rate of carbonyl compounds, making it easier to extract aldehydes and ketones rapidly. This technique utilises electrophoresis, chromophores, fluorophores, and functional groups for detection and extraction. It initially began as a batch procedure but has now developed into an automated, microextraction, and derivatization method. Solid-phase analytical derivatization is highly efficient due to the significant excess of the derivatizing reagent relative to the analyte, along with the pre-impregnation of derivatizing reagents, which can speed up the process compared to traditional solution-based derivatization. This tutorial aims to provide detailed insights into the practical aspects of implementing solid-phase analytical derivatization in analytical method development and discuss the prospects and future trends.

Nonsteroidal anti-inflammatory drugs (NSAIDs) are a class of drugs with antipyretic, analgesic, and anti-inflammatory effects widely used worldwide. This study aimed at developing an environmentally friendly and high-throughput sample preparation method for the determination of six NSAIDs in urine samples followed by high-performance liquid chromatography coupled to diode-array detection (HPLC-DAD). The experimental workflow consisted of hollow-fiber microporous membrane liquid-liquid extraction (HF-MMLLE) using a supramolecular solvent immobilized into the porous of polypropylene hollow membranes (1 cm length). These membranes were attached to a 96-well plate system to permit multiple extractions simultaneously. Under the optimized conditions, limits of detection (LODs) and limits of quantification (LOQs) ranged from 6.06 to 30.3 µg/L and from 20 to 100 µg/L, respectively. The linear ranges varied from 20 to 1000 µg/L for indomethacin and diclofenac, from 50 to 1000 µg/L for ketoprofen and ibuprofen, and from 100 to 1000 µg/L for naproxen and fenoprofen. The coefficients of determination (R²) ranged from 0.9735 to 0.9997. Intraday precision ranged from 6.13 to 20.11 %, interday precision varied from 2.87 to 20.72 %, and accuracy ranged from 92.49 to 126.89 %. Moreover, the recently proposed Sample Preparation Metric of Sustainability (SPMS) was employed to evaluate the greenness of the sample preparation technique resulting in a score of 8.0, which is highly satisfactory according to the concepts of green analytical chemistry.

In this comparative study, four green evaluation tools, blue applicability grade index (BAGI), Analytical GREEnness (AGREE), Green Analytical Procedure Index (GAPI), and Analytical Eco-Scale were evaluated to assess 16 selected analytical methods including fiber-solid phase microextraction, stir bar sorptive extraction, and thin film microextraction joint to gas and liquid chromatographic as well as spectrofluorimetry techniques. The required parameters and data were extracted from the selected articles and calculations were performed based on the unique evaluation protocol of each tool. A uniform approach was applied in calculations and evaluations. A comparison of selected methods was done by determining the factors affecting greenness. High energy consumption, organic solvents, waste generation, analysis throughput, and the number of determined analytes, are among the crucial parameters that require improvement in the selected methods. The results show that using more than one evaluation tool in evaluating the greenness of analytical methods is very effective in obtaining synergistic results and increasing the understanding of the greenness of analytical methods.

Conventional analytical methodologies for the determination of organic contaminants in water matrices are often laborious and time-consuming, and require a large amount of chemicals. In this study, we have developed a green sample preparation approach using Araucaria angustifolia bracts as a natural sorbent in the bar adsorptive microextraction technique. The determination of eight emerging contaminants (methyl, propyl, and butylparaben, bisphenols A and F, estradiol, ethinylestradiol, and benzophenone) in river-water samples were carried out, employing high-performance liquid chromatography with diode-array detection (HPLC-DAD). Central composite design revealed that the best conditions for the extraction step involved adding 30 % (w/v) NaCl to the sample at pH 6 and leaving it for 180 min. Simplex-centroid design indicated 80 μL of a mixture of acetonitrile and water (3:1) as the best desorption solvent. Desorption time was univariately evaluated as 40 min. Calibration curves obtained correlation coefficients higher than 0.995. The limits of quantification were in the range of 1 to 10 µg L−1 with inter-day precision from 13 to 22 %. Relative recoveries in two river-water samples varied from 62 to 116 %, exhibiting relative standard deviations from 5 to 28 %, which confirmed the method's accuracy and precision. This method contributes to the development of more environmentally friendly sample preparation strategies.

This study was conducted to optimize a targeted plant proteomics approach from signature peptide selection and liquid chromatography with tandem mass spectrometry (LC-MS/MS) analytical method development and optimization to sample preparation method optimization. Three typical protein extraction and precipitation methods, including trichloroacetic acid (TCA)/acetone method, phenol method, and TCA/acetone/phenol method, and two digestion methods, including trypsin digestion and LysC/trypsin digestion, were evaluated for selected proteins related to the impact of engineered nanomaterials (ENMs) on wheat (Triticum aestivum) plant growth. In addition, we compared two plant tissue homogenization methods: grinding freeze-dried tissue and fresh tissue into a fine powder using a mortar and pestle aided with liquid nitrogen. Wheat plants were grown under a 16 h photoperiod (light intensity 150 μmol·m-2·s-1) for 4 weeks at 22 °C with a relative humidity of 60% and were watered daily to maintain a 70-90% water content in the soil. Processed samples were analyzed with an optimized LC-MS/MS method. The concentration of selected signature peptides for the wheat proteins of interest indicated that the phenol extraction method using fresh plant tissue, coupled with trypsin digestion, was the best sample preparation method for the targeted proteomics study. Overall, the optimized approach yielded the highest total peptide concentration (68,831 ng/g, 2.4 times the lowest concentration) as well as higher signature peptide concentrations for most peptides (19 out of 28). In addition, three of the signature peptides could only be detected using the optimized approach. This study provides a workflow for optimizing targeted proteomics studies.

The Ga+ focused Ion Beam (FIB) or Xe+ Plasma FIB (PFIB) procedure has enabled the ability to make specimens where mechanical tests in the microscale regime can be achieved with high precision. Nevertheless, milling times can be long and shape optimization can be arduous collectively limiting the ability to readily make a sufficient number of test samples. In this work, we present a sample preparation technique for microscale cantilever fabrication which streamlines the milling procedures by using combined electropolishing and FIB milling. Specifically, the procedure mitigates extensive undercutting requirements which reduces the fabrication time for the microcantilever to more than half that time as compared to direct milling methods from making similar geometries directly from the bulk material. This process is discussed along with specific aspects related to the sample alignment of the cantilever to specific fracture planes for single crystals. In addition, we comment on the applicability of this method to polycrystalline samples.

The article presents the research on the adaptation and implementation of a method for determining mono- and diacylglycerols in vegetable oils. The relevance of the research is determined by the introduction of standardization of monochloropropanediols and glycidol in vegetable oils and some types of fat and oil products since 2025. According to the scientific literature, mono- and diacylglycerols, formed during the ripening of oil seeds under the influence of the enzyme lipase, are precursors of monochloropropanediols and glycidol, which, in turn, according to the World Health Organization, are carcinogenic substances. Some of the most probable mechanisms for the formation of contaminants from mono- and diacylglycerols have been considered; according to them diacylglycerols are considered to be the main source of glycidyl ethers, and monoacylglycerols are that of monochloropropanediols. An important factor influencing the speed and completeness of the described reactions is the presence in the system of water molecules, chlorine ions, hydrogen protons, as well as high temperatures. Catalysts for such side reactions are heavy metals, including their salts. Thus, in order to implement effective measures to control the formation of contaminants in oil, it is important to have a complete picture of the quality indicators of the feedstock and, above all, data on the content of mono- and diacylglycerols, methods for determining which are not available in laboratory practice in the Russian Federation.The goal of the research is to develop a method for the quantitative determination of mono- and diacylglycerols in vegetable oils.As a result of the research, the sample preparation method has been improved, calibration dependencies have been determined using an internal standard, and an identification and quantitative analysis technique has been proposed, on the basis of gas chromatography with a flame ionization detector and the use of a high-temperature capillary column. Verification work has been carried out and the metrological characteristics of the proposed method have been determined. The method has been tested on real objects – various types of vegetable oils.

SCIENTIFIC RELEVANCE. An important quality-control issue for therapeutic monoclonal antibodies (mAbs) is the determination of residual protein A leaching from the carrier during the purification of mAbs by affinity chromatography. However, unrelated compounds (immunoglobulins) present in the sample can complicate the immunoenzymatic detection of protein A (matrix effect), potentially leading to false-negative test results. To increase the efficiency of enzyme-linked immunosorbent assay (ELISA), it is necessary to develop a sample preparation step that can irreversibly break the bond in the protein A–mAb complex.AIM. This study aimed to develop and validate an analytical procedure for the determination of residual protein A in active substances of therapeutic mAbs by ELISA with a test kit comprising in-house reagents.MATERIALS AND METHODS. Recombinant protein A was used as an antigen. Polyclonal antibodies to protein A were produced by immunising chickens, selecting immunised eggs, and isolating antibodies from these eggs. Protein A-specific antibodies were purified by affinity chromatography. Residual protein A was determined using sandwich ELISA with preliminary sample preparation. The analytical procedure was validated in accordance with the requirements of the State Pharmacopoeia of the Russian Federation (Validation of Analytical Procedures, OFS.1.1.0012).RESULTS. The authors obtained, isolated, and purified chicken IgY antibodies to recombinant protein A. The authors selected sample preparation conditions for the determination of residual protein A by ELISA and optimum compositions of buffer solutions, including the composition of a denaturing buffer to disrupt the protein A–mAb complex. The developed analytical procedure was validated. According to the measurements of protein A, the accuracy of the analytical procedure ranged within 83–108% of the nominal value, the interlaboratory precision ranged within 96–116%, and the repeatability was up to 13%. The lower limit of quantitation was 10 ng/mL with a minimum required dilution of 1:10. The analytical range extended from 10 to 40 ng/mL. The analytical procedure showed results comparable to those obtained with a similar test kit from an international manufacturer.CONCLUSIONS. The developed analytical procedure for the determination of residual protein A by ELISA with a test kit comprising in-house reagents can minimise the matrix effect in therapeutic mAbs. This analytical procedure will alleviate import substitution and reduce quality control costs for Russian immunobiologicals.

Microwave-induced combustion (MIC) was proposed in this study for honey decomposition aiming for As, Cd, Hg, and Pb determination by inductively coupled plasma mass spectrometry (ICP-MS). Sample mass (up to 1.0 g), absorbing solution (0.5 to 14.4 mol L−1 HNO3, and H2O), heating program, and combustion aids were evaluated. The Eurachem guidelines were used for method validation. The proposed method enabled combustion of a high sample mass (0.8 g of honey, with 0.4 g of microcrystalline cellulose and 100 µL of 6 mol L−1 NH4NO3) using 6 mL of an absorbing solution consisting of 1 mol L−1 HNO3, which resulted in low residual carbon in solution (< 25 mg L−1). Honey samples from different geographical origins were analyzed. Results showed no significant difference in comparison to other two microwave decomposition methods, based on microwave-assisted wet digestion with single reaction chamber (MAWD-SRC) and microwave-assisted wet digestion (MAWD). Standard addition experiments resulted in recoveries higher than 98%. The limits of detection ranged from 1.10 (As) to 4.60 ng g−1 (Pb). In addition to using only diluted reagents and resulting in digests virtually free of interferences, the proposed method was faster (< 30 min) than most of those presented in the literature. [ABSTRACT FROM AUTHOR]

This work discusses ceramic filter materials used as substrates to study biological objects by electron microscopy. The composition, structure, pore sizes, and morphology of ceramic substrates made of foamed silicate prior to and following the application of inverse silicon oxide opals were evaluated by x-ray diffraction analysis and SEM method. Adescription of the use of the obtained filtering substrates in an experiment with biological objects is given. The substrates seem promising for electron microscopy, since they can be used for sample preparation of biological objects with the use of metal spraying or ionic liquid. This technique, together with the filtering porous material and the technical capabilities of the microscope, preserves the physical characteristics of biological objects. [ABSTRACT FROM AUTHOR]

Aquatic ecosystems serve as the primary reservoir for microplastics entering the environment. The assessment of the microplastics content in natural waters and sediments is a pressing task, the resolution of which is essential for evaluating the degree of pollution of water bodies, identifying sources of contamination, and assessing potential risks to aquatic inhabitants. Currently, there is no universal analytical approach to separating microplastics from natural waters and sediments for subsequent identification. This review summarizes information on the methods for sampling microplastics from natural waters and sediments and sample preparation techniques, including size- and density-based particle separation methods, as well as digestion-based methods relying on the digestion of samples to remove natural organic matter. Additionally, it outlines the classification of microplastics and provides general insights into their prevalence in aquatic ecosystems and potential toxicity. [ABSTRACT FROM AUTHOR]

The continuous growth in the production, unsustainable use, and disposal of plastics in recent decades has led to the emergence of a new type of pollutant, microplastics (MPs). In this article, the focus is on the form of MPs, which are produced by the fragmentation of textile fibres during washing processes. The problems associated with the characterisation and quantification of MPs in this type of sample are related to the wide range of concentrations, forms, and degree of degradation as well as physico-chemical and biological properties. Although the basic principles for the analysis of microplastics present in the environmental samples are known, there is the lack of standardised methods for the analysis of MPs in laundry effluents and domestic washing. Therefore, the continuous development of sophisticated analytical techniques and methodologies is required for the reliable collection and isolation, quantification, and characterisation of one of the most challenging analytes. The aim of this review is to outline the key steps of MPs analysis in laundry effluents and domestic washing, focusing on those steps that are underestimated in the current literature: sampling and sample preparation for analysis. Precisely these analytical steps, which can become the main source of analytical measurement system errors, ensure the quality of the analysis. This paper emphasises the importance of monitoring background contamination and presents guidelines to ensure quality control specifically for this type of analyte. [ABSTRACT FROM AUTHOR]

Organophosphate flame retardants (OPFRs) are high-production volume chemicals widely present in environmental compartments. The presence of water-soluble OPFRs (tri-n-butyl phosphate (TnBP), tris(2-butoxyethyl) phosphate (TBEP), tris(2-chloroethyl) phosphate (TCEP), tris(2-chloroisopropyl) phosphate (TCPP), and triethyl phosphate (TEP)) in water compartments evidences the struggle of conventional wastewater treatment plants (WWTPs) to effectively eliminate these toxic compounds. This study reports for the first time the use of white-rot fungi as a promising alternative for the removal of these OPFRs. To accomplish this, a simple and cost-efficient quantification method for rapid monitoring of these contaminants' concentrations by GC–MS while accounting for matrix effects was developed. The method proved to be valid and reliable for all the tested parameters. Sample stability was examined under various storage conditions, showing the original samples to be stable after 60 days of freezing, while post-extraction storage techniques were also effective. Finally, a screening of fungal degraders while assessing the influence of the glucose regime on OPFR removal was performed. Longer chain organophosphate flame retardants, TBP and TBEP, could be easily and completely removed by the fungus Ganoderma lucidum after only 4 days. This fungus also stood out as the sole organism capable of partially degrading TCEP (35% removal). The other chlorinated compound, TCPP, was more easily degraded and 70% of its main isomer was removed by T. versicolor. However, chlorinated compounds were only partially degraded under nutrient-limiting conditions. TEP was either not degraded or poorly degraded, and it is likely that it is a transformation product from another OPFR's degradation. These results suggest that degradation of chlorinated compounds is dependent on the concentration of the main carbon source and that more polar OPFRs are less susceptible to degradation, given that they are less accessible to radical removal by fungi. Overall, the findings of the present study pave the way for further planned research and a potential application for the degradation of these contaminants in real wastewaters. [ABSTRACT FROM AUTHOR]

Nowadays, molecularly imprinted polymers (MIPs) are well established and are considered excellent materials for performing selective extractions. However, with the progressive implementation of the principles of green chemistry, it is necessary to find greener alternatives for both the synthesis and further use of MIPs in sample preparation. Accordingly, in the present work, different deep eutectic solvents (DES, both hydrophilic and hydrophobic), as an alternative to conventional organic solvents (i.e., toluene), were evaluated as porogens for the synthesis of imprinted fibers (monoliths), using fused silica capillaries as molds, for solid-phase microextraction (SPME). From this study, the polymer prepared with propazine (dummy template), methacrylic acid (monomer), ethylene glycol dimethacrylate (cross-linker), and a formic acid:L-menthol (1:1) DES (porogen) showed the best performance for selective rebinding of triazines. After optimization of the different variables involved in SPME, the new imprinted fibers were successfully applied to the extraction of target analytes (desisopropylatrazine, desethylatrazine, simazine, and atrazine) from soil sample extracts, providing relative recoveries ranging from 75.7 to 120.1%, reaching limits of detection within the range of 6.2–15.7 ng g−1, depending upon the analyte. [ABSTRACT FROM AUTHOR]

Commercial viticulture necessitates regular pesticide applications to manage diseases and pests, raising significant concerns regarding pesticide residues among stakeholders. Due to health risks associated with these residues in Turkish vine leaves, the European Commission has increased the frequency of official control from 20% to 50%. Thus, the aim of this study was to determine multi-class pesticide residues in brined vine leaves from Turkey. A total of 766 samples of vine leaves were collected between May 2022 and June 2023. More than 500 residues were analyzed using the quick, easy, cheap, effective, rugged, and safe (QuEChERS) method, followed by liquid chromatography-tandem mass spectrometry. In-house validation data demonstrated that the analytical method exhibits fit-for-purpose performance in terms of linearity, accuracy, precision, and measurement uncertainty. Out of 766 samples analyzed, 180 samples (23.5%) contained one (131, 17.1%) or multiple (49, 6.4%) pesticides. Both the frequencies of occurrence and the rate of maximum residue level (MRL) exceedance increased in 2023 compared to 2022, with the MRL exceedance rate rising from 9.5% to 25.2%. Forty-three different residues were found in quantifiable concentrations and eight of them were non-approved. Among the residues, the non-systemic pyrethroid insecticides, lambda-cyhalothrin (8.0%) and cypermethrin (7.2%), were the two most frequently detected, with concentrations ranging from 0.010 to 0.248 mg kg−1 and from 0.011 to 0.533 mg kg−1 , respectively. Turkey is a major exporter of vine leaves and these results provide crucial information regarding pesticide occurrence and quality assessment of vine leaves. The significant increase in both pesticide occurrence and MRL exceedance rates between 2022 and 2023 underscores the urgency for regulatory bodies to reassess current pesticide usage and monitoring practices. The findings emphasize the importance of implementing more stringent rules and improving enforcement methods in order to reduce the spread of unapproved pesticides and ensure adherence to global food safety standards. [ABSTRACT FROM AUTHOR]