Search

The selection of abrasive material and parameters of the Air-Abrasion device for a particular application is a crucial detail. However, there are no standard recommendations or manuals for choosing these details; the operator must depend on his experience and knowledge of the procedure to select the best possible material and set of parameters. This short review attempts to identify some of the effects that the selection of material and parameters could have on the performance of the Air-Abrasion procedure for a particular application. The material and parameter data are collected from various studies and categorized according to the most popular materials in use right now. These studies are then analyzed to arrive at some inferences on the performance of Air-Abrasion materials and parameters. This review arrives at a few conclusions on the effectiveness of a material and parameter set, and that there is potential for developments in the area of standardizing parameter selection; also, there is scope for further studies on Bio-Active Glass as an alternative to the materials currently used in Air-Abrasion. [ABSTRACT FROM AUTHOR]

Renal transplantation is the treatment of choice for improved survival and quality of life in patients with end-stage renal disease. However, perirenal fluid collections are common surgical complications after renal transplant, with about 0.6 to 18% of patients developing a lymphocele. Conventional treatments include percutaneous aspiration and drainage, laparoscopic fenestration, and open surgical decompression stepwise. Recently, a new image-guided percutaneous transperitoneal balloon fenestration technique has been described as an alternative to the laparoscopic or surgical technique. We present the case of a 25-year-old male patient diagnosed with a lymphocele after 2 months of transplantation and no resolution of the lymphocele with percutaneous aspiration and drainage. We used this new technique under ultrasound and fluoroscopy guidance, which resulted in the resolution of the lymphocele at 1 month postprocedure. This case report highlights this new technique's potential role in successfully managing the posttransplant lymphocele in a minimally invasive manner. [ABSTRACT FROM AUTHOR]

The airflow behaviour and particle deposition before and after the maxillary expansion are evaluated using the computational fluid dynamics method. A pediatric patient was subjected to maxillary expansion and the CT scans of pre and post were recorded. The procured CT scans were developed into 3D models using Materialise MIMICS 21.0 (Materialise, Ann Arbor, MI). The analysis was performed using ANSYS FLUENT 2020 R2 with three different flow rates defined at the nostril inlet as 5, 10, and 15 LPM. The surface area and nasal volume increased by 5.1% and 16.5%, respectively, for the post-maxillary expansion case. The velocity profiles show a maximum value at the nasal valve regions followed by a decreased velocity in the mid-nasal region with an 85% lower velocity observed at the nasal valve for the post-maxillary expansion case. The nasal resistance and pressure drop decrease by 46% to 66% in post-maxillary expansion cases. The maximum WSS at the nasal valve region is observed which is reduced by around 47% for postmaxillary expansion cases. Particle deposition studies show a reduction in particle depositions in post cases indicating a greater number of inhaled particles reaching the lungs. The pressure drop and the nasal resistance values were reduced by more than 50% for post-maxillary expansion. The particle deposition studies show increased depositions at higher flow rates for both cases. [ABSTRACT FROM AUTHOR]

In replacement surgery of the hip joint, an implant is replaced into the natural femur which recreates the articulation and functionally of a natural joint. Total hip replacement is significantly increasing by the day worldwide and is likely to increase by 174% by 2030. Primary revision is another major concern for total hip replacement with revision rates likely to increase by 137%. The first part of the article states the basic anatomy of the hip joint, different ligaments in the hip, the disorders associated with the joint, and evaluation of total hip arthroplasty. In the second part some of the major works are highlighted followed by a detailed discussion about different design considerations and wear-related issues in hip joints. More emphasis is given to the tribological behavior of implants under different conditions. The design aspects and several parameters which affect the wear rate in implants are summarized. Also, different testing methods which are used both in experimental and numerical techniques are reported to estimate the wear rates in hip implants with the evolution of hip implants since the early 20th century, in terms of different designs, materials and wear hip implant arthroplasty is known as one of the best advancements in healthcare. Further research is needed to establish to improve the life expectancy of hip implants. [ABSTRACT FROM AUTHOR]

The effect of structural chemistry of different soft segments on various structural properties of polyurethane-urea (PUU) elastomers was evaluated in this study. A series of PUU elastomers were prepared by the reaction of 4,4'-diisocyanato dicylohexylmethane (H12MDI) with polycaprolactone (PCL), Polytetramethylene glycol (PTMG), Polyethylene glycol (PEG), Polybutylene adipate (PBA) and amine chain extender 4,4'-methylenebis(2,6-diethylaniline) (MBDEA). Fourier transform infrared (FTIR) spectroscopy was used to study the synthesis of final PUU elastomers. Thermal behaviour of PUU elastomers was investigated by thermogravimetric analysis (TGA) and differential scanning calorimetry (DSC) analysis. The surface properties and hardness of elastomers were characterized by measuring contact angle and hardness in shore A scale. The results showed highest thermal stability and hydrophobicity of PUPCL i.e., Polycaprolactone polyol based PUU elastomer. The proposed synthesis of PUU elastomers was confirmed by the appearance of -NH peak at 3305-3315 cm-1 and disappearance of -NCO peak at 2270 cm-1 in FTIR spectra. [ABSTRACT FROM AUTHOR]

In this study, we evaluated the morphological behavior of polyurethane elastomers (PUEs) by modifying the soft segment chain length. This was achieved by increasing the soft segment molecular weight (Mn = 400–4000 gmol−1). In this regard, polycaprolactone diol (PCL) was selected as the soft segment, and 4,4′-cyclohexamethylene diisocyanate (H12MDI) and 1,6-hexanediol (HDO) were chosen as the hard segments. The films were prepared by curing polymer on Teflon surfaces. Fourier transform infrared spectroscopy (FTIR) was utilized for functional group identification in the prepared elastomers. FTIR peaks indicated the disappearance of −NCO and −OH groups and the formation of urethane (NHCOO) groups. The morphological behavior of the synthesized polymer samples was also elucidated using scanning electron microscopy (SEM) and atomic force microscopy (AFM) techniques. The AFM and SEM results indicated that the extent of microphase separation was enhanced by an increase in the molecular weight of PCL. The phase separation and degree of crystallinity of the soft and hard segments were described using X-ray diffraction (XRD). It was observed that the degree of crystallinity of the synthesized polymers increased with an increase in the soft segment's chain length. To evaluate hydrophilicity/hydrophobicity, the contact angle was measured. A gradual increase in the contact angle with distilled water and diiodomethane (38.6°–54.9°) test liquids was observed. Moreover, the decrease in surface energy (46.95–24.45 mN/m) was also found to be inconsistent by increasing the molecular weight of polyols. [ABSTRACT FROM AUTHOR]