Search

Potassium-ion batteries (KIBs) have received widespread attention as an alternative to lithium-ion batteries because of their low cost and abundance of potassium. However, the poor kinetic performance and severe volume changes during charging/discharging due to the large radius of potassium leading to low capacity and rapid decay. Therefore, development of anode materials with sufficient space and active sites for potassium ion deintercalation and desorption is necessary to ensure structural stability and good electrochemical activity. This study prepared boron-doped pine-cone carbon (BZPC) with 3D interconnected hierarchical porous in ZnCl2 molten-salt by calcination under high temperature. The hierarchical porous structure promoted the penetration of the electrolyte, improved charge-carrier diffusion, alleviated volume changes during cycling, and increased the number of micropores available for adsorbing potassium ions. In addition, due to B doping, the BZPC material possessed abundant defects and active centers, and a wide interlayer distance, which enhanced the adsorption of K ions and promoted their intercalation and diffusion. When used as the anode of a KIB, BZPC provided a high reversible capacity (223.8 mAh g−1 at 50 mA g−1), excellent rate performance, and cycling stability (115.9 mAh g−1 after 2000 cycles at 1 A g−1).

Manganese is widely used in many fields. Many efforts have been made to recover manganese from low-grade pyrolusite due to the depletion of high-grade manganese ore. Thus, it is of practical significance to develop a clean, energy-saving and environmentally friendly technical route to reduce the low-grade pyrolusite. The reported results show that biomass wastes from crops, crop waste, wood and wood waste are environmentally friendly, energy-saving, and low-cost reducing agents for roasting reduction of low-grade pyrolusite. Kinetics of the reduction reactions is necessary for an efficient design of biomass reduction of pyrolusite. Therefore, it is important to look for a general kinetics equation to describe the reduction of pyrolusite by different kinds of biomass, because there is a wide variety of biomass wastes, meaning that it is impossible to investigate the kinetics for each biomass waste. In this paper, thermal gravimetric analysis and differential thermal analysis were applied to study the overall reduction kinetics of pyrolusite using a mixture of hemicellulose and lignin, two major components of biomass. Overall reduction process is the overlap of the respective reduction processes. A new empirical equation based on the Johnson–Mehl–Avrami equation can be used to describe the respective reduction kinetics using hemicellulose and lignin as reductants, and the corresponding apparent activation energy is 30.14 kJ mol−1 and 38.91 kJ mol−1, respectively. The overall kinetic model for the reduction of pyrolusite by the mixture of hemicellulose and lignin can be simulated by the summation of the respective kinetics by considering their mass-loss fractions, while a unit step function was used to avoid the invalid conversion data. The obtained results in this work are necessary to understand the biomass reduction of pyrolusite and provide valuable assistance in the development of a general kinetics equation.

Olivine-type LiMnPO4/C nanorods were successfully synthesized in a chloride/ethylene glycol-based deep eutectic solvent (DES) at 130 °C for 4 h under atmospheric pressure. As-synthesized samples were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), Raman spectroscopy, Fourier transform infrared spectroscopy (FTIR) and electrochemical tests. The prepared LiMnPO4/C nanorods were coated with a thin carbon layer (approximately 3 nm thick) on the surface and had a length of 100–150 nm and a diameter of 40–55 nm. The prepared rod-like LiMnPO4/C delivered a discharge capacity of 128 mAh·g−1 with a capacity retention ratio of approximately 93% after 100 cycles at 1 C. Even at 5 C, it still had a discharge capacity of 106 mAh·g−1, thus exhibiting good rate performance and cycle stability. These results demonstrate that the chloride/ethylene glycol-based deep eutectic solvents (DES) can act as a new crystal-face inhibitor to adjust the oriented growth and morphology of LiMnPO4. Furthermore, deep eutectic solvents provide a new approach in which to control the size and morphology of the particles, which has a wide application in the synthesis of electrode materials with special morphology.

Porous MnO/C microspheres have been successfully fabricated by a fast co-precipitation method in a T-shaped microchannel reactor. The structures, compositions, and electrochemical performances of the obtained MnO/C microspheres are characterized by X-ray diffraction, field emission scanning electron microscopy (FE-SEM), transmission electron microscopy (HRTEM), Brunauer-Emmett-Teller analysis, charge-discharge testing, cyclic voltammograms, and electrochemical impedance spectra. Experimental results reveal that the as-prepared MnO/C, with a specific surface area of 96.66 m²•g-1 and average pore size of 24.37 nm, exhibits excellent electrochemical performance, with a discharge capacity of 655.4 mAh•g-1 after cycling 50 times at 1 C and capacities of 808.3, 743.7, 642.6, 450.1, and 803.1 mAh•g-1 at 0.2, 0.5, 1, 2, and 0.2 C, respectively. Moreover, the controlled method of using a microchannel reactor, which can produce larger specific surface area porous MnO/C with improved cycling performance by shortening lithium-ion diffusion distances, can be easily applied in real production on a large scale. [ABSTRACT FROM AUTHOR]

Olivine-type LiMnPO4/C nanorods were successfully synthesized in a chloride/ethylene glycol-based deep eutectic solvent (DES) at 130 °C for 4 h under atmospheric pressure. As-synthesized samples were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), Raman spectroscopy, Fourier transform infrared spectroscopy (FTIR) and electrochemical tests. The prepared LiMnPO4/C nanorods were coated with a thin carbon layer (approximately 3 nm thick) on the surface and had a length of 100-150 nm and a diameter of 40-55 nm. The prepared rod-like LiMnPO4/C delivered a discharge capacity of 128 mAh.g-1 with a capacity retention ratio of approximately 93% after 100 cycles at 1 C. Even at 5 C, it still had a discharge capacity of 106 mAh.g-1, thus exhibiting good rate performance and cycle stability. These results demonstrate that the chloride/ethylene glycol-based deep eutectic solvents (DES) can act as a new crystal-face inhibitor to adjust the oriented growth and morphology of LiMnPO4. Furthermore, deep eutectic solvents provide a new approach in which to control the size and morphology of the particles, which has a wide application in the synthesis of electrode materials with special morphology. [ABSTRACT FROM AUTHOR]

Abstract: The kinetics of reductive leaching of manganese from low grade pyrolusite using melanoidins of molasses alcohol wastewater as reducing agent in dilute sulfuric acid was investigated. The shrinking core model was applied to quantify the effects of reaction parameters on leaching rate of manganese. The leaching rate increases with the increase of the leaching temperature, sulfuric acid concentration and melanoidins concentration and the decreases of the particle size of pyrolusite. The leaching process follows the kinetics of a shrinking core model and the apparent activation energy is 56.2 kJ·mol-1. The experimental results indicate a reaction order of 0.54 for sulfuric acid concentration and 0.93 for melanoidins concentration. It is concluded that the reductive leaching of pyrolusite with macromolecular melanoidins of molasses alcohol wastewater is controlled by the diffusion through the ash/inert layer composed of the associated minerals. [Copyright &y& Elsevier]