Search

Item does not contain fulltext, This study assessed whether the Symax implant, a modification of the Omnifit((R)) stem (in terms of shape, proximal coating and distal surface treatment), would yield improved bone remodelling in a clinical DEXA study, and if these results could be predicted in a finite element (FE) simulation study. In a randomized clinical trial, 2 year DEXA measurements between the uncemented Symax and Omnifit((R)) stem (both n=25) showed bone mineral density (BMD) loss in Gruen zone 7 of 14% and 20%, respectively (p<0.05). In contrast, the FE models predicted a 28% (Symax) and 26% (Omnifit((R))) bone loss. When the distal treatment to the Symax was not modelled in the simulation, bone loss of 35% was predicted, suggesting the benefit of this surface treatment for proximal bone maintenance. The theoretical concept for enhanced proximal bone loading by the Symax, and the predicted remodelling pattern were confirmed by DEXA-results, but there was no quantitative match between clinical and FE findings. This was due to a simulation based on incomplete assumptions concerning the yet unknown biological and mechanical effects of the new coating and surface treatment. Study listed under ClinicalTrials.gov with number NCT01695213.

1 april 2013, Item does not contain fulltext, In cementless total hip arthroplasty, long-term implant stability is achieved by bone ingrowth. The strength of the new bond gradually increases in time, due to bone maturation and progression of ingrowth. In finite element simulations, osseointegration generally is implemented as an instant change in the mechanical behavior of the implant-bone interface, although this is a simplified interpretation of the bone ingrowth process. The aim of the present study was to build on previous bone ingrowth simulations and propose a new methodology to simulate bone ingrowth as a time-dependent process. We developed an algorithm to calculate the strength of the local implant-bone bond based of the magnitude of interface micromotions and gaps in time. Our algorithm was subsequently tested in multiple hip reconstructions in which the bone quality and implant-bone contact area were varied. The results of the simulations showed that in the ideal situation (good bone quality and no interface gaps), 91% of implant area could achieve ingrowth, while in the worst case only 17% of implant area showed ingrowth. The initial contact area had a significant effect on ingrowth, overruling the effect of variations in bone quality. The progression of ingrowth had a stabilizing effect on adjacent regions, especially in the high contact area cases. Further development and validation of the presented algorithm requires more information on the nature of the relation between the ingrowth rate and the magnitude of micromotions and gap.

Radboud Universiteit Nijmegen, 6 november 2012, Promotor : Verdonschot, N.J.J. Co-promotor : Janssen, D.W., Contains fulltext : 107923.pdf (publisher's version ) (Open Access)

1 juli 2012, Item does not contain fulltext, The finite element (FE) method has become a common tool to evaluate peri-prosthetic micromotions in cementless total hip arthroplasty. Often, only the peak joint load and a selected number of muscle loads are applied to determine micromotions. Furthermore, the applied external constraints are simplified (diaphyseal fixation), resulting in a non-physiological situation. In this study, a scaled musculoskeletal model was used to extract a full set of muscle and hip joint loads occurring during a walking cycle. These loads were applied incrementally to an FE model to analyze micromotions. The relation between micromotions and external loads was investigated, and how micromotions during a full loading cycle compared to those calculated when applying a peak load only. Finally, the effect of external constraints was analyzed (full model vs. diaphyseal fixation and reduced number of muscle loads). Relatively large micromotions were found during the swing phase when the hip joint forces were relatively low. Maximal micromotions, however, did concur with the peak hip joint force. Applying only a peak joint force resulted in peak micromotions similar to those found when full walking cycle loads were applied. The magnitude and direction of the micromotions depended on the applied muscle loads, but not on external constraints.

Item does not contain fulltext, In order to design a good cementless femoral implant many requirements need to be fulfilled. For instance, the range of micromotions at the bone-implant interface should not exceed a certain threshold and a good ratio between implant-bone stiffness that does not cause bone resorption, needs to be ensured. Stiff implants are known to evoke lower interface micromotions but at the same time they may cause extensive resorption of the surrounding bone. Composite stems with reduced stiffness give good remodeling results but implant flexibility is likely to evoke high micromotions proximally. Finding a good balance between these incompatible design goals is very challenging. The current study proposes a finite element methodology that employs subsequent ingrowth and remodeling simulations and can be of assistance when designing new implants. The results of our simulations for the Epoch stem were in a good agreement with the clinical data. The proposed implant design made of porous tantalum with an inner CoCrMo core performed slightly better with respect to the Epoch stem and considerably better with respect to a Ti alloy stem. Our combined ingrowth and remodeling simulation can be a useful tool when designing a new implant that well balances mentioned incompatible design goals.

Item does not contain fulltext, In total hip arthroplasty, micromotions at the implant-bone interface influence the long-term survival of the prosthesis. These micromotions are often measured using sensors that are fixed to the implant and bone at points that are remote from the interface. Given that the implant-bone system is not rigid, errors may be introduced. It is not possible to assess the magnitude of these errors with the currently available experimental methods. However, this problem can be investigated using the finite element method (FEM). The hypothesis that the actual interface micromotions differ from those measured in the experimental manner was tested using a case-specific FE model, validated against deflection experiments. The FE model was used to simulate an 'experimental' method to measure micromotions. This 'experimental' method was performed by mimicking the distance between the measurement points; the implant point was selected at the interface while the bony point was at the outer surface of bone. No correlation was found between the micromotions computed at the interface and when using remote reference points. Moreover, the magnitudes of micromotions computed with the latter method were considerably greater. By reducing the distance between the reference points the error decreased, but the correlation stayed unchanged. Care needs to be taken when interpreting the results of micromotion measurement systems that use bony reference points at a distance from the actual interface.

Item does not contain fulltext