Search

In this study, nickel supported on various metal oxides were prepared by simple impregnation and the performance for CO2 methanation was tested. The oxide supports were all prepared by thermal decomposition of metal salts to provide comparable oxide properties such as surface area. Among the investigated oxides, nickel supported on CeO2 and Y2O3 showed the highest CO2 conversion of 90% at 320 °C with highest CH4 selectivity of 99%. The order of catalyst activity (XCO2@320°C) was reported: Ni/CeO2 ~ Ni/Y2O3 > > Ni/La2O3 > Ni/ZrO2 > Ni/Al2O3 > Ni/MgO > Ni/CaO > > Ni/MnO. The physicochemical properties of the catalysts were analyzed by TEM, BET, XRD, ICP, H2-TPR, CO2-TPD, H2 chemisorption, TGA, Raman, and XPS. From the characterization results, the catalyst activity was independent to specific surface area of catalyst and crystallite size of Ni. The amount of oxygen vacancies and weak-to-medium basic sites exhibited major roles for enhancing catalyst activity. The CeO2 and Y2O3 as reducible oxide supports not only provided abundant oxygen vacancies / basic sites, but also promoted Ni dispersion with appropriate interaction between metal and support, resulting in higher reducibility at low temperature. The reduction of catalyst at high temperature can significantly improve the performance of Ni supported on non-reducible MgO. However, the Ni/CeO2 and Ni/Y2O3 reduced at high temperature suffered from coalescence of CeO2 and Y2O3, though Ni crystallite sizes are well preserved from sintering. [ABSTRACT FROM AUTHOR]

In this study, the improvement of heat transfer was applied to eliminate hotspots of a highly exothermic reaction, Fischer–Tropsch synthesis (FTS), by means of two facile methods: (I) adding high thermal conductive materials media diluted in catalysts (SiC and Al chips), and (II) using structured reactors equipped with well-designed structured catalysts with advantages of heat dissipation/removal. The 20%Co/SiO2 catalyst powder prepared by simple impregnation was employed for constructing structured catalysts and granular packed bed catalysts. The structured catalyst was prepared by coating method of Co/SiO2 slurry on an aluminum spiral and plate substrate. The catalytic performance of as-prepared catalysts was then tested for FTS in a fixed-bed reactor at 210–230 °C, 20 bar. Both gaseous and liquid products were collected and analyzed. The heat transfer improvement of packed bed catalytic system and structured catalytic system were compared and discussed. As a result, the structured catalytic system with spiral structured catalyst can provide the best improvement of heat/mass transfer, resulting in enhanced diesel selectivity, though the oil production rate was unsatisfactory. Meanwhile, among the packed bed catalytic systems, SiC media possessed the best heat removal material, producing the highest oil yield. In addition, the fresh and spent catalysts were analyzed by several techniques including TEM, SEM, XRD, BET, ICP-OES, H2–TPR, and TGA to relate the physicochemical properties of the prepared catalysts and its FTS performance. [ABSTRACT FROM AUTHOR]

Direct conversion of biogas via the integrative process of dry reforming of methane (DRM) and catalytic methane decomposition (CDM) has received a great attention as a promising green catalytic process for simultaneous production of syngas and carbon nanotubes (CNTs). In this work, the effects of reaction temperature of 700–1100 °C and CH4/CO2 ratio of biogas were investigated over NiMo/MgO catalyst in a fixed bed reactor under industrial feed condition of pure biogas. The reaction at 700 °C showed a rapid catalyst deactivation within 3 h due to the formation of amorphous carbon on catalyst surface. At higher temperature of 800–900 °C, the catalyst can perform the excellent performance for producing syngas and carbon nanotubes. Interestingly, the smallest diameter and the highest graphitization of CNTs was obtained at high temperature of 1000 °C, while elevating temperature to 1100 °C leads to agglomeration of Ni particles, resulting in a larger size of CNTs. The reaction temperature exhibits optimum at 800 °C, providing the highest CNTs yield with high graphitization, high syngas purity up to 90.04% with H2/CO ratio of 1.1, and high biogas conversion (XCH4 = 86.44%, XCO2 = 95.62%) with stable performance over 3 h. The typical composition biogas (CH4/CO2 = 1.5) is favorable for the integration process, while the CO2 rich biogas caused a larger grain size of catalyst and a formation of molybdenum oxide nanorods (MoO3). The long-term stability of NiMo/MgO catalyst at 800 °C showed a stable trend (> 20 h). The experimental findings confirm that NiMo/MgO can perform the excellent activity and high stability at the optimum condition, allowing the process to be more promising for practical applications. [ABSTRACT FROM AUTHOR]

The upgradation of methane in biogas by hydrogenation of CO2 has been currently recognized as a promising route for efficient full utilization of renewable biogas with potential benefits for storage of renewable hydrogen energy and abatement of greenhouse gas emission. As a main constituent of biogas, CO2 can act as a backbone for the formation of additional CH4 by hydrogenation, then producing higher amounts of biomethane. In this work, the upgradation process was investigated in a prototype reactor of double pass operation with vertical alignment using an optimized Ni-Ce/Al-MCM-41 catalyst. The experimental results show that the double pass operation that removes water vapor during the run can significantly increase CO2 conversion, resulting in higher CH4 production yield. As a result, the purity of biomethane increased by 15% higher than a single pass operation. In addition, search for optimum condition of the process was carried out within an investigated range of conditions including flowrate (77–1108 ml min−1), pressure (1 atm–20 bar), and temperature (200–500 °C). The durability test for 458 h was performed using the obtained optimum condition, and it shows that the optimized catalyst can perform excellent stability with negligible influence by the observed change in catalyst properties. The comprehensive characterization on physicochemical properties of fresh and spent catalysts was performed, and the results were discussed. [ABSTRACT FROM AUTHOR]

This work aims to enhance the value of palm empty fruit bunches (EFBs), an abundant residue from the palm oil industry, as a precursor for the synthesis of luminescent carbon dots (CDs). The mechanism of fIuorimetric sensing using carbon dots for either enhancing or quenching photoluminescence properties when binding with analytes is useful for the detection of ultra-low amounts of analytes. This study revealed that EFB-derived CDs via hydrothermal synthesis exceptionally exhibited luminescence properties. In addition, surface modification for specific binding to a target molecule substantially augmented their PL characteristics. Among the different nitrogen and sulfur (N and S) doping agents used, including urea (U), sulfate (S), p-phenylenediamine (P), and sodium thiosulfate (TS), the results showed that PTS-CDs from the co-doping of p-phenylenediamine and sodium thiosulfate exhibited the highest PL properties. From this study on the fluorimetric sensing of several metal ions, PTS-CDs could effectively detect Fe3+ with the highest selectivity by fluorescence quenching to 79.1% at a limit of detection (LOD) of 0.1 µmol L−1. The PL quenching of PTS-CDs was linearly correlated with the wide range of Fe3+ concentration, ranging from 5 to 400 µmol L−1 (R2 = 0.9933). [ABSTRACT FROM AUTHOR]

A series of activated carbons (ACs) derived from spent disposable wooden chopsticks was prepared via steam activation and used to separate carbon dioxide (CO2) from a CO2/hydrogen (H2) mixed gas at atmospheric pressure. A factorial design was employed to investigate the effects of the activation temperature and time as well as their interactions on the production yield of ACs and their CO2 adsorption capacity. The activation temperature exhibited a much higher impact on both the production yield and the CO2 adsorption capacity of ACs than the activation time. The interaction of both parameters did not significantly affect the yield of ACs, but did affect the CO2 adsorption capacity. The optimal preparation condition provided ACs with a desirable yield of around 23.18% and a CO2 adsorption capacity of 85.19 mg/g at 25 °C and 1 atm and consumed the total energy of 225.28 MJ/kg AC or 116.4 MJ/g-mol CO2. A H2 purity of greater than 96.8 mol% was achieved from a mixed gas with low CO2 concentration (< 20 mol%) during the first 3 min of adsorption and likewise around 90 mol% from a mixed gas with a high CO2 concentration (> 30 mol%) during the first 2 min. The CO2 adsorption on the as-prepared ACs proceeded dominantly via multilayer physical adsorption and was affected by both the surface area and micropore volume of the ACs. The adsorption capacity was diminished by around 18% after six adsorption/desorption cycles. The regeneration of the as-prepared chopstick-derived ACs can be easily performed via heating at a low temperature and ambient pressure, suggesting their potential application in the temperature swing adsorption process. [ABSTRACT FROM AUTHOR]

Developing a metallic catalyst for converting furfural (FAL) to highly valuable products such as cyclopentanone (CPO) is important for fine chemical synthesis by the efficient utilization of biomass resources. The presence of diverse unsaturated carbon atoms in FAL and the rearrangement of oxygen atoms hinder the production of CPO. We developed an optimal nickel (Ni)-to-platinum (Pt) molar ratio (1:0.007) for a bimetallic Ni-Pt/alumina (Al 2 O 3 ) catalyst with a low Pt loading via an impregnation method to efficiently catalyze the selective hydrogenation of FAL in an aqueous solution to form CPO. The comprehensive characterizations by X-ray diffraction and X-ray absorption near edge structure analyses elucidated the formation of Ni 0 /Pt 0 and Ni 2+ /Pt 4+ after reduction by H 2 . The addition of a low amount of the Pt-Ni/Al 2 O 3 catalyst resulted in an alleviation of H 2 reduction behavior detected by hydrogen temperature-programmed reduction, accompanied by low H 2 desorption ability observed by hydrogen temperature-programmed desorption. The catalytic activity of Ni-Pt/Al 2 O 3 was higher than those of Ni/Al 2 O 3 and Pt/Al 2 O 3 catalysts. The maximum CPO yield was 66% with 93% FAL conversion under the optimized conditions (160 °C, 20 bar of H 2 pressure, and 2 h). Isotopic deuterium oxide (D 2 O) labeling revealed the transfer of deuterium (D) atoms from D 2 O to the intermediates and products during hydrogenation and rearrangement, which confirmed that water was a medium for rearrangement and the source of hydrogen for the reaction. This study developed an efficient catalyst for the catalytic hydrogenation and ring rearrangement of FAL into CPO., Competing Interests: The authors declare no competing financial interest., (© 2024 The Authors. Published by American Chemical Society.)

The upgradation of methane in biogas by hydrogenation of CO 2 has been currently recognized as a promising route for efficient full utilization of renewable biogas with potential benefits for storage of renewable hydrogen energy and abatement of greenhouse gas emission. As a main constituent of biogas, CO 2 can act as a backbone for the formation of additional CH 4 by hydrogenation, then producing higher amounts of biomethane. In this work, the upgradation process was investigated in a prototype reactor of double pass operation with vertical alignment using an optimized Ni-Ce/Al-MCM-41 catalyst. The experimental results show that the double pass operation that removes water vapor during the run can significantly increase CO 2 conversion, resulting in higher CH 4 production yield. As a result, the purity of biomethane increased by 15% higher than a single pass operation. In addition, search for optimum condition of the process was carried out within an investigated range of conditions including flowrate (77-1108 ml min -1 ), pressure (1 atm-20 bar), and temperature (200-500 °C). The durability test for 458 h was performed using the obtained optimum condition, and it shows that the optimized catalyst can perform excellent stability with negligible influence by the observed change in catalyst properties. The comprehensive characterization on physicochemical properties of fresh and spent catalysts was performed, and the results were discussed., (© 2023. The Author(s).)

Natural kaolin-based Ni catalysts have been developed for low-temperature CO 2 methanation. The catalysts were prepared via a one-step co-impregnation of Ni and Ce onto a natural kaolin-derived metakaolin using a microwave-assisted hydrothermal method as an acid-/base-free synthesis method. The influences of microwave irradiation and Ce promotion on the catalytic enhancement including the CO 2 conversion, CH 4 selectivity, and CH 4 yield were experimentally investigated by a catalytic test of as-prepared catalysts in a fixed-bed tubular reactor. The relationship between the catalyst properties and its methanation activities was revealed by various characterization techniques including X-ray fluorescence, X-ray diffraction, Brunauer-Emmett-Teller, scanning electron microscopy, selected area electron diffraction, transmission electron microscopy, elemental mapping, H 2 temperature-programmed reduction, and X-ray absorption near-edge structure analyses. Among the two enhancement methods, microwave and Ce promotion, the microwave-assisted synthesis could produce a catalyst containing highly dispersed Ni particles with a smaller Ni crystallite size and higher catalyst reducibility, resulting in a higher CO 2 conversion from 1.6 to 7.5% and a better CH 4 selectivity from 76.3 to 79.9% at 300 °C. Meanwhile, the enhancement by Ce addition exhibited a great improvement on the catalyst activities. It was experimentally found that the CO 2 conversion increased approximately 7-fold from 7.5 to 52.9%, while the CH 4 selectivity significantly improved from 79.9 to 98.0% at 300 °C. Though the microwave-assisted synthesis could further improve the catalyst activities of Ce-promoted catalysts, the Ce addition exhibited a more prominent impact than the microwave enhancement. Cerium oxide (CeO 2 ) improved the catalyst activities through mechanisms of higher CO 2 adsorption capacity with its basic sites and the unique structure of CeO 2 with a reversible valence change of Ce 4+ and Ce 3+ and high oxygen vacancies. However, it was found that the catalyst prepared by microwave-assisted synthesis and Ce promotion proved to be the optimum catalyst in this study. Therefore, the present work demonstrated the potential to synthesize a nickel-based catalyst with improved catalytic activities by adding a small amount of Ce as a catalytic promoter and employing microwave irradiation for improving the Ni dispersion., Competing Interests: The authors declare no competing financial interest., (© 2021 The Authors. Published by American Chemical Society.)

Hydrodeoxygenation (HDO) of bio-oil derived from liquefaction of a palm empty fruit bunch (EFB) in glycerol was investigated. To enhance the heating value and reduce the oxygen content of upgraded bio-oil, hydrodeoxygenation of light bio-oil over Ni- and Co-based catalysts on an Al 2 O 3 support was performed in a rotating-bed reactor. Two consecutive steps were conducted to produce bio-oil from EFB including (1) microwave-assisted wet torrefaction of EFB and (2) solvothermolysis liquefaction of treated EFB in a Na 2 CO 3 /glycerol system. The HDO of as-prepared bio-oil was subsequently performed in a unique design reactor possessing a rotating catalyst bed for efficient interaction of a catalyst with bio-oil and facile separation of the catalyst from upgraded bio-oil after the reaction. The reaction was carried out in the presence of each mono- or bimetallic catalyst, namely, Co/Al 2 O 3 , Ni/Al 2 O 3 , NiMo/Al 2 O 3 , and CoMo/Al 2 O 3 , packed in the rotating-mesh host with a rotation speed of 250 rpm and kept at 300 and 350 °C, 2 MPa hydrogen for 1 h. From the results, the qualities of upgraded bio-oil were substantially improved for all catalysts tested in terms of oxygen reduction and increased high heating value (HHV). Particularly, the NiMo/Al 2 O 3 catalyst exhibited the most promising catalyst, providing favorable bio-oil yield and HHV. Remarkably greater energy ratios and carbon recovery together with high H/O, C/O, and H/C ratios were additionally achieved from the NiMo/Al 2 O 3 catalyst compared with other catalysts. Cyclopentanone and cyclopentene were the main olefins found in hydrodeoxygenated bio-oil derived from liquefied EFB. It was observed that cyclopentene was first generated and subsequently converted to cyclopentanone under the hydrogenation reaction. These compounds can be further used as a building block in the synthesis of jet-fuel range cycloalkanes., Competing Interests: The authors declare no competing financial interest., (© 2021 The Authors. Published by American Chemical Society.)

In the present work, the solvent-free hydrodeoxygenation of palm oil as a representative triglyceride model compound to diesel-like hydrocarbons was evaluated in a batch reactor using Pt-decorated MoO 2 catalysts. The catalysts with various Pt loadings (0.5-3%) were synthesized by an incipient wetness impregnation method. The metallic Pt and MoO 2 phases were detected in the XRD patterns of as-prepared catalysts after the reaction and acted as active components for the deoxygenation reactions. The XPS experiments confirmed the existence of metallic Pt and PtO x species. The XANES investigation of Mo L 3 -edge spectra elucidated a change in the valence state by the transformation of MoO 3 into MoO 2 species after the deoxygenation reaction. The TEM observation revealed the formation of Pt nanoparticles in the range of 1-3 nm decorated on MoO 2 species. The number of acid sites increased with stronger metal-support interactions on increasing the Pt loading. The catalytic performance of the MoO 2 catalyst significantly improved with a small amount of Pt decoration. However, the further increase in Pt loading did not relatively increase the deoxygenation activity due to the formation of the agglomerated Pt particles. The high performance of the decorated catalysts could be attributed to the moderate acidity from the Pt dispersed on MoO 2 toward decarbonylation and decarboxylation reactions., Competing Interests: The authors declare no competing financial interest., (Copyright © 2020 American Chemical Society.)