Search

This study focused on developing an advanced bitterness sensor designed to minimize interference from common anions such as nitrate (NO3−) and iodide (I−) by incorporating partially dissociated amine compounds into the sensor membrane. The conventional bitter sensor (C00) uses fully dissociated quaternary ammonium salt tetradecyl ammonium bromide (TDAB), which typically exhibits high responses to these anions, leading to inaccurate bitterness assessments. To address this issue, we explored the use of three partially dissociated amines—oleylamine (OAm), dioctadecylamine (DODA), and tridodecylamine (TDA)—as lipids in the membrane components. We fabricated sensor membranes and tested their ion selectivity, interference resistance to anion, and sensitivity to iso-alpha acids (IAAs), representative bitter compounds in beer. The results showed that the membranes with partially dissociated amines significantly reduced anion interference. Notably, the sensitivity of the TDA membrane to IAAs was 80.4 mV/dec in concentration, exceeding the 68.5 mV/dec of the TDAB membrane. This enhanced sensitivity, coupled with reduced anion interference, reveals a novel property of partially dissociated lipids in taste sensors, distinguishing them from fully dissociated lipids. These findings pave the way for the development of sensors that can accurately assess a bitter taste and have potential applications in the food and beverage industry. [ABSTRACT FROM AUTHOR]

A modified carbon paste sensor based on N,N′-(((ethane-1,2-diylbis(oxy))bis(2,1-phenylene))bis(methanylylidene))bis(pyridine-2-amine; BPA Schiff base as Cr(III) selective carrier was fabricated and studied in this work. The proposed sensor homogenization and mechanism of action was studied by infra-red (IR) and scanning electron microscope (SEM) with energy dispersive X-ray (EDX) tools. The sensor covered 1.0 × 10−7–1.0 × 10–1 mol L−1 linear range and a detection limit of 7.22 × 10–8 mol L−1 for Cr(III) with 20.17 ± 0.13 mV decade−1 Nernstian slope. 5 s was the response time of the prepared sensor and it was reproducible and stable for 3 months. The working pH range was 3.3–6.0 and it also works well to determine Cr(III) ion in presence of water miscible solvents up to 12.5% content of the methanol and 17.5% of ethanol. The electrode's selectivity was studied using separate and mixed solution methods for selectivity coefficients determination and the sensor showed good selectivity relative to a variety of metal ions (selectivity coefficients = 1.01 × 10−5–8.57 × 10−3). In addition, the practical analysis value of the sensor was demonstrated by measurement of Cr(III) quantitatively in mineral water, supplement and also as an indicator electrode in Cr(III) against EDTA potentiometric titration with good reproducibility (RSDs of 0.91–2.15%). [ABSTRACT FROM AUTHOR]

The increasing emergence of multidrug-resistant (MDR) pathogens due to antibiotic misuse translates into obstinate infections with high morbidity and high-cost hospitalizations. To oppose these MDR superbugs, new antimicrobial options are necessary. Although both quaternary ammonium salts (QASs) and phosphonium salts (QPSs) possess antimicrobial effects, QPSs have been studied to a lesser extent. Recently, we successfully reported the bacteriostatic and cytotoxic effects of a triphenyl phosphonium salt against MDR isolates of the Enterococcus and Staphylococcus genera. Here, aiming at finding new antibacterial devices possibly active toward a broader spectrum of clinically relevant bacteria responsible for severe human infections, we synthesized a water-soluble, sterically hindered quaternary phosphonium salt (BPPB). It encompasses two triphenyl phosphonium groups linked by a C12 alkyl chain, thus embodying the characteristics of molecules known as bola-amphiphiles. BPPB was characterized by ATR-FTIR, NMR, and UV spectroscopy, FIA-MS (ESI), elemental analysis, and potentiometric titrations. Optical and DLS analyses evidenced BPPB tendency to self-forming spherical vesicles of 45 nm (DLS) in dilute solution, tending to form larger aggregates in concentrate solution (DLS and optical microscope), having a positive zeta potential (+18 mV). The antibacterial effects of BPPB were, for the first time, assessed against fifty clinical isolates of both Gram-positive and Gram-negative species. Excellent antibacterial effects were observed for all strains tested, involving all the most concerning species included in ESKAPE bacteria. The lowest MICs were 0.250 µg/mL, while the highest ones (32 µg/mL) were observed for MDR Gram-negative metallo-β-lactamase-producing bacteria and/or species resistant also to colistin, carbapenems, cefiderocol, and therefore intractable with currently available antibiotics. Moreover, when administered to HepG2 human hepatic and Cos-7 monkey kidney cell lines, BPPB showed selectivity indices > 10 for all Gram-positive isolates and for clinically relevant Gram-negative superbugs such as those of E. coli species, thus being very promising for clinical development. [ABSTRACT FROM AUTHOR]

Carbon nanomaterials were introduced into this research as modifiers for polymeric membranes for single-piece electrodes, and their properties were studied for the case of nitrate-selective sensors. The use of graphene, carbon black and carbon nanotubes is shown to significantly improve the potentiometric response, while no redox response was observed. The use of carbon nanomaterials results in a near-Nernstian response (54 mV/pNO3−) towards nitrate ions over a wide linear range (from 10−1 to 10−6 M NO3−). The results obtained by chronopotentiometry and electrochemical impedance spectroscopy reveal little resistance, and the capacitance parameter is as high as 0.9 mF (for graphene-based sensor). The high electrical capacity of electrodes results in the good stability of the potentiometric response and a low potential drift (0.065 mV/h). Introducing carbon nanomaterials into the polymetric membrane, instead of using them as separate layers, allows for the simplification of the sensors' preparation procedure. With single-piece electrodes, one step of the procedure could be omitted, in comparison to the procedure for the preparation of solid-contact electrodes. [ABSTRACT FROM AUTHOR]

A series of activated carbons (YMBC) obtained from yerba mate twig residue (YMT) were prepared by chemical (H3PO4) and thermal activation. Five materials were synthesized, varying the carbonization temperature (400–600 °C under N2 atmosphere) and H3PO4:YMT ratio (60–80 wt%). They were physicochemically and texturally characterized by SEM-EDX, BET, FT-IR, and 31P MAS-NMR. Potentiometric titration with the n-butylamine technique was used to evaluate their acidic properties. The materials exhibited a high specific surface area (572 m2 g−1 < SBET < 1031 m2 g−1) and mesoporosity (67% < Smeso/SBET < 93%). The results showed that the acid strength and the number of acid sites increased with the H3PO4:YMT ratio and decreased with the calcination temperature increment. The FT-IR and 31P characterization revealed the presence of Hn+2PnO3n+1 species firmly (via P-O-C linkages) and loosely attached (by electrostatic interaction). The latter were successfully removed by refluxing the material in water or n-propanol. The optimal reaction conditions were applied to the synthesis of other levulinic acid esters using YMBC-500-70NP as a catalyst. Furthermore, the effective separation of the product combined with the use of a recyclable catalyst resulted in a clean and environmentally friendly strategy for the synthesis of alkyl levulinates, bioproducts of relevance to the biorefinery industry, which can be applied as fragrances, flavoring agents, as well as fuel additives. [ABSTRACT FROM AUTHOR]

Lately, children's daily consumption of some products, such as cereals and candies, has been rising, which provides a compelling rationale for determining any metallic substances that may be present. Monitoring the concentration of certain metals, like nickel, in these products is necessary due to medical issues in humans when consumed regularly. So, in this work, a novel and highly selective carbon paste as a Ni(II) ion-selective sensor was prepared and investigated using ceramic magnesium aluminum spinel nanoparticles as the ionophore and tritolyl phosphate (TOCP) as a plasticizer. A modified co-precipitation method was used to synthesize the spinel nanoparticles. X-ray diffraction, scanning electron microscope with EDAX, transmission electron microscope, and BET surface area were used to determine the phase composition, microstructure, pores size, particle size, and surface area of the synthesized nanoparticles. The spinel nanoparticle was found to have a nano crystallite size with a cubic crystal system, a particle size ranging from 17.2 to 51.52 nm, mesoporous nature (average pore size = 8.72 nm), and a large surface area (61.75 m2/g). The composition ratio of graphite carbon as a base: TOCP as binder: spinal as ionophore was 67.3:30.0:2.7 (wt%) based on potentiometric detections over concentrations from 5.0 × 10−8 to 1.0 × 10−2 mol L−1 with LOD of 5.0 × 10−8 mol L−1. A measurement of 29.22 ± 0.12 mV decade−1 over pH 2.0–7.0 was made for the Nernstian slope. This sensor demonstrated good repeatability over nine weeks and a rapid response of 8 s. A good selectivity was shown for Ni(II) ions across many interferents, tri-, di-, and monovalent cations. The Ni(II) content in spiked real samples, including cocaine, sweets, coca, chocolate, carbonated drinks, cereals, and packages, were measured. The results obtained indicated no significant difference between the proposed potentiometric method and the officially reported ICP method according to the F- and t-test data. In addition to utilizing ANOVA statistical analysis, validation procedures have been implemented, and the results exceed the ICP-MS methodology. [ABSTRACT FROM AUTHOR]

Under ideal conditions, nanotubes with a fixed negative tube-wall charge will reject anions and transport-only cations. Because many proposed nanofluidic devices are optimized in this ideally cation-permselective state, it is important to know the experimental conditions that produce ideal responses. A parameter called Ccrit, the highest salt concentration in a contacting solution that still produces ideal cation permselectivity, is of particular importance. Pioneering potentiometric studies on gold nanotubes were interpreted using an electrostatic model that states that Ccrit should occur when the Debye length in the contacting salt solution becomes equivalent to the tube radius. Since this "double-layer overlap model" (DLOM), treats all same-charge ions as identical point charges, it predicts that all same-charged cations should produce the same Ccrit. However, the effect of cation on Ccrit in gold nanotubes was never investigated. This knowledge gap has become important because recent studies with a polymeric cation-permselective nanopore membrane showed that DLOM failed for every cation studied. To resolve this issue, we conducted potentiometric studies on the effect of salt cation on Ccrit for a 10 nm diameter gold nanotube membrane. Ccrit for all cations studied were, within experimental error, the same and identical, with values predicted by DLOM. The reason DLOM prevailed for the gold nanotubes but failed for the polymeric nanopores stems from the chemical difference between the fixed negative charges of these two membranes. [ABSTRACT FROM AUTHOR]

Solid-contact ion-selective electrodes (SC-ISEs) have the advantages of easy miniaturization, even chip integration, easy carrying, strong stability, and more favorable detection in complex environments. They have been widely used in conjunction with portable, wearable, and intelligent detection devices, as well as in on-site analysis and timely monitoring in the fields of environment, industry, and medicine. This article provides a comprehensive review of the composition of sensors based on redox capacitive and double-layer capacitive SC-ISEs, as well as the ion–electron transduction mechanisms in the solid-contact (SC) layer, particularly focusing on strategies proposed in the past three years (since 2021) for optimizing the performance of SC-ISEs. These strategies include the construction of ion-selective membranes, SC layer, and conductive substrates. Finally, the future research direction and possibilities in this field are discussed and prospected. [ABSTRACT FROM AUTHOR]

Self‐powered pressure detection using smart wearable devices is the subject of intense research attention, which is intended to address the critical need for prolonged and uninterrupted operations. Current piezoelectric and triboelectric sensors well respond to dynamic stimuli while overlooking static stimuli. This study proposes a dual‐response potentiometric pressure sensor that responds to both dynamic and static stimuli. The proposed sensor utilizes interdigital electrodes with MnO2/carbon/polyvinyl alcohol (PVA) as the cathode and conductive silver paste as the anode. The electrolyte layer incorporates a mixed hydrogel of PVA and phosphoric acid. The optimized interdigital electrodes and sandpaper‐like microstructured surface of the hydrogel electrolyte contribute to enhanced performance by facilitating an increased contact area between the electrolyte and electrodes. The sensor features an open‐circuit voltage of 0.927 V, a short‐circuit current of 6 µA, a higher sensitivity of 14 mV/kPa, and outstanding cycling performance (>5000 cycles). It can accurately recognize letter writing and enable capacitor charging and LED lighting. Additionally, a data acquisition and display system employing the proposed sensor, which facilitates the monitoring of athletes' rehabilitation training, and machine learning algorithms that effectively guide rehabilitation actions are presented. This study offers novel solutions for the future development of smart wearable devices. [ABSTRACT FROM AUTHOR]

The work is devoted to the study of the influence of nitrogenous bases on the composition of oil and the structure of asphaltenes on their colloidal stability in solution. Model petroleum systems with a basic nitrogen content of 1, 2, and 3% wt. were used as objects of study. Asphaltene-like nitrogenous bases were obtained by thermolysis of model petroleum systems with different nitrogen contents. The results were obtained using elemental analysis, non-aqueous potentiometric titration, spectrophotometry, 1H NMR spectroscopy, and liquid adsorption chromatography. It was established that the content of Nbas in asphaltenes increases by 0.3–1.3% wt. with the increase in quinoline content in petroleum components. Quinoline is incorporated into the supramolecular structure of asphaltenes and increases their average molecular weight by 650 amu. and aromaticity by 2%. The aggregative stability of asphaltenes decreases by 1.5–6 times with an increase in their average molecular weight and an increase in Nbas in their composition as a component of a dispersion medium. The colloidal stability of synthetic asphaltene-like substances, on the contrary, is due to the appearance of their molecular sequence of fragments containing Nbas in aromatic rings. [ABSTRACT FROM AUTHOR]

Fluorine, depending on its concentration and chemical form, is essential or toxic to humans and animals. Therefore, it is crucial to be able to determine it reliably. In this study, fluorine was determined in animal feed after extraction with HCl (gastric juice simulation). The standard potentiometric method with a fluoride-selective electrode (ISE) and newly developed high-resolution continuum source graphite furnace molecular absorption spectrometry (HR-CS GFMAS) method was applied. Feed samples turned out to be a challenge for HR-CS GFMAS. Chemical interferences (formation of competing molecules, CaF, GaCl, and GaP, instead of the target GaF molecule) and spectral effects (including a phosphorous molecule spectrum and atomic lines) were identified. An additional difficulty was caused by reagent contamination with F and memory effects. Difficulties were eliminated/reduced. The quality of ISE analysis was multi-directionally verified (including comprehensive proficiency testing). A risk of inaccuracy at low F concentration, where the calibration relationship is nonlinear, was investigated. The results of both methods were consistent, which confirms the accuracy of the methods and informs that the extracted fluorine is in fluoride form. The results of extensive ISE tests conducted in Poland in 2021–2023 have shown that, in most cases, the fluoride content is significantly lower than the threshold values. [ABSTRACT FROM AUTHOR]

Potentiometric titration in a fast and simultaneously high-resolution modality was proposed for the identification and quantification of protolytic groups of variable strength at the surface of primary soil particles. The method is implemented by titrimetric data processing as multicomponent spectra (pKa spectrotitrimetry). Due to the high resolution, the error of acidity-constant assessment (3–5%) is lower, compared to existing approaches; due to the fast titration, the effect of soil hydrolysis is minimized. The soil profiles for acidic Retisols (podzolic soils)—under a spruce crown and in the intercrown space—were studied. These soils, which have similar bulk properties and genesis but developed under different plant covers, were distinguished by pKa spectral features at 4–5; 5.5–6.5; 6.5–8.5; 7.5–8.5; and 9–10, as well as total group concentrations. Differences in acidic and basic-group distribution (carboxyl groups, amorphous aluminosilicates, carbonate species, amino groups, soluble (poly)phenolic compounds, phospholipids) and Al and Fe complex compounds within the same soil profiles and between two Retisols were found and quantified. The acidity constants and group concentrations found by pKa spectrotitrimetry were compared with conventional soil-composition indicators (total organic carbon, oxalate-soluble Fe and Al, and phosphorus), using principal component analysis. The main correlations are between the concentrations of oxalate-soluble Al and groups with pKa values of 5.0–6.5 and 8.5; oxalate-soluble Fe and pKa values of 9.0–10.0; and P2O5 and pKa values of 4.0–6.0 and 6.5–8.5. The method provides a set of major acidity values without a priori information on a soil sample and can be used for screening and identifying similar soils. [ABSTRACT FROM AUTHOR]

Flow injection amperometry provides an opportunity to avoid common drawbacks of classical potentiometry for solid-contact ion-selective electrodes. The current is generated by solid-contact in course of the polymer chain recharging in response to an excess of cations or anions in the polymer film. Cations cause cathodic peaks on the chronoamperogram, while anions result in anodic peaks. For polyaniline with negatively charged substituents, a response to cations is observed, whereas the presence of uncharged ones results in anion detection. Moreover, in the case of the protonated –SO3H group, this compensating current is an order of magnitude lower than that for the deprotonated one. For electroactive self-doped polyanilines, the maximal amperometric signal is achieved at the working potential within the electroactivity range. The proposed constant potential amperometric approach was validated by the successful analysis of human serum with a Na+-selective electrode based on polyaniline. [ABSTRACT FROM AUTHOR]

Graphene oxide (GO) was used as an ion-to-electron transducer for all-solid-state nitrate electrodes based on an alkyl ammonium salt as the sensing element. Commercially available carbon screen-printed electrodes modified with GO were used as conductive substrates, whose morphology and distribution along the surface were evaluated by scanning electron microscopy and Raman spectroscopy. The potentiometric performance of the GO-based electrodes revealed a Nernstian slope of −53.5 ± 2.0 mV decade−1 (R2 = 0.9976 ± 0.0015) in the range from 3.0 × 10−6 to 10−2 M and a lower limit of detection of 1.9 × 10−6 M. An impressive reproducibility between equally prepared electrodes (n = 15) was demonstrated by a variation of <6% for the calibration parameters. Constant current chronopotentiometry and water layer tests were used to evaluate the potential signal stability, providing similar performance to previously published works with graphene-based ion-selective electrodes. Notably, the GO-based sensors showed the absence of a water layer, a long-term drift of 0.3 mV h−1, and a stable performance (LOD and sensitivity) over 3 months. The applicability of the proposed sensors was demonstrated in determining nitrate levels in water samples with great accuracy, yielding recovery values from 87.8 to 107.9%, and comparable (p > 0.05) results to a commercial nitrate probe. These findings demonstrate the use of GO as an alternative ion-to-electron transducer for the fabrication of all-solid-state potentiometric electrodes. [ABSTRACT FROM AUTHOR]

Phosphate is an important fertilizer in agriculture and electrochemical sensors based on cobalt (Co) are promising for measurement of phosphate. The deposition of Co onto conductive substrates to form a nano/microstructured Co layer with rich active sites is a typical strategy to improve detection performances. However, the widely used substrates show smooth surfaces, which cannot provide extra active sites. Herein, a high‐performance phosphate sensor is fabricated by generating Co nanoparticles (NPs) on a hierarchically porous laser‐induced graphene (LIG) matrix with a large surface area. Specifically, a Co layer is first electroplated on the LIG matrix. Nevertheless, the pores of LIG will be blocked by the dense Co layer so the performances of the fabricated LIG‐Co sensor exhibit limited enhancements. Therefore, a "nearly all etching (NAE)" technique is developed to transform the dense Co layer to dispersive Co NPs and re‐expose the pores of LIG, both increasing the active sites. Compared to the LIG‐Co sensor, the LIG‐Co NP sensor displays overall superiority. The response time, sensitivity, and linearity are enhanced from ≈60 to ≈10 s, from 0.012 to 0.069 V dec−1, and from 0.973 to 0.998, respectively. The LIG‐Co NP sensor also shows a decent anti‐interference capability. [ABSTRACT FROM AUTHOR]

Copper(II), nickel(II) and zinc(II) complexes of various peptide fragments of tau protein were studied by potentiometric and spectroscopic techniques. All peptides contained one histidyl residue and represented the sequences of tau(91–97) (Ac-AQPHTEI-NH2), tau(385–390) (Ac-KTDHGA-NH2) and tau(404–409) (Ac-SPRHLS-NH2). Imidazole-N donors of histidine were the primary metal binding sites for all peptides and all metal ions, but in the case of copper(II) and nickel(II), the deprotonated amide groups were also involved in metal binding by increasing pH. The most stable complexes were formed with copper(II) ions, but the presence of prolyl residues resulted in significant changes in the thermodynamic stability and speciation of the systems. It was also demonstrated that nickel(II) and especially zinc(II) complexes have relatively low thermodynamic stability with these peptides. The copper(II)-catalyzed oxidation of the peptides was also studied. In the presence of H2O2, the fragmentation of peptides was detected in all cases. In the simultaneous presence of H2O2 and ascorbic acid, the fragmentation of the peptide is less preferred, and the formation of 2-oxo-histidine also occurs. [ABSTRACT FROM AUTHOR]

Recently, fluorescent sensors have gained considerable attention due to their high sensitivity, low cost and noninvasiveness. Among the different materials that can be used for this purpose, carbon dots (CDs) represent valuable candidates for applications in sensing. These, indeed, are easily synthesized, show high quantum yield and are highly biocompatible. However, it was pointed out that the photoluminescence properties of these nanomaterials are strictly dependent on the synthetic and purification methods adopted. The presence of halloysite nanotubes (HNTs), a natural, low cost and biocompatible clay mineral, has been found to be efficient in obtaining small and highly monodispersed CDs without long and tedious purification techniques. Herein, we report the comparison of synthetic pathways for obtaining halloysite-N-doped CDs (HNTs-NCDs) that could be used in biological sensing. One was based on the synthesis of N-doped CDs by a bottom-up approach on HNTs' surface by a MW pyrolysis process; the other one was based on the post-modification of pristine N-doped CDs with halloysite derivatives. The evaluation of the best synthetic route was performed by different physico-chemical techniques. It was found that the bottom-up approach led to the formation of N-doped CDs with different functional groups onto the HNTs' surface. This evidence was also translated in the different fluorescence quantum yields and the existence of several functional groups in the obtained materials was investigated by potentiometric titrations. Furthermore, the ability of the synthesized nanomaterials as sensors for Fe3+ ions detection was assessed by spectroscopic measurements, and the cellular uptake was verified by confocal/fluorescence microscopies as well. [ABSTRACT FROM AUTHOR]

Schematic diagram of the whole process for detecting sulfur-containing components in lithium-sulfur batteries, including graded leaching, efficient oxidation and precise quantitative detection. [Display omitted] • A highly effective approach for the graded leaching and precise quantitative detection techniques of sulfur-containing components within Li-S batteries has been successfully developed. The total detection rate of this method for sulfur-containing components in Li-S batteries exceeds 99 %. • Clarify that the presence of lithium polysulfide in the electrolyte after discharge is the main factor for restricting the full utilization of Li-S batteries' capacity, and propose targeted improvement measures. • This study offers a considerably refined and comprehensive methodology for the capacity fading and failure mechanisms assessment of high-energy-density Li-S batteries. Lithium-sulfur (Li-S) batteries are a strong contender for the new-generation battery system to meet the growing energy demand due to their significantly high energy density (2600 Wh/kg) and cost-effectiveness. However, the practical operating conditions yield an initial capacity of less than 80 % of the theoretical capacity, resulting in a limited lifespan and hindering broader application. What's worse, current mechanism, especially the evolution process of sulfides for the initial capacity degradation is not clear due to the practical difficulties of effective separation and detection of sulfur-containing components. Herein, we have developed an instrumental analysis method enabling graded leaching and quantitative determination of sulfur-containing components. This technology achieves a detection precision surpassing 99.11 %, addressing the inherent deficiency in calculating sulfur-containing components using the decrement method. Applying this method reveals that the presence of lithium polysulfides in the electrolyte (26.34 wt%) after discharging is the primary factor causing insufficient capacity utilization in Li-S batteries. This work not only demonstrates the unique behavior of Li-S batteries at high sulfur loading but also provides a systematic evaluation method to guide further research on high-energy-density batteries, and provides theoretical and technical support to promote the development of high-energy, long-life Li-S batteries. [ABSTRACT FROM AUTHOR]

Human skin protects the organs, tissues, and systems of the body from the effects of external irritants and the acid-base state of the skin provides a significant barrier factor. The surface layer of the epidermis was studied using non-invasive potentiometry methods before and after applying daily hygiene products. The possibility of obtaining rapid assessments of the restoration of the protective function of human skin is shown to be an important factor in assessing the general condition of the microflora and the immune function of the skin. [ABSTRACT FROM AUTHOR]

The acid ionization constants (pKa) of the N-benzoylthiourea / 2-thiohydantoin-pyrrolidines were determined by the potentiometric titration method. Titrations were performed by adding sodium chloride, which gives ionic strength, and hydrochloric acid, which is required for the protonation of the ionizable groups, to 2x10-4 M solutions of the synthesized compounds prepared in an acetonitrile-water (20:80, v / v) solvent system at 25 ± 0.1 °C and sodium hydroxide was used as a titrant. The HYPERQUAD computer program was utilized to determine acid ionization constants based on the data obtained from the Molspin Titration System. Analyzing the obtained results, it is possible to propose three pKa (pKa1, pKa2, and pKa3) values that correspond to the enol, thiol, and NH species for N-benzoylthiourea derivatives in the range of 3.02-10.91 and carboxyl, enol and enthiol species for thiohydantoin derivatives in the range of 2.13-10.96. [ABSTRACT FROM AUTHOR]

The suitability of various nitrogen, sulfur, oxygen, and phosphorus compounds as complexing agents in a silver electrolyte was examined by using potentiometric titration under practical conditions. The setup consisted of three electrodes to measure the pH and the activity of the silver ions simultaneously. Different ratios of silver to complexing agent from 1:10 to 1:1 at a constant ionic strength of 0.2 mol/L were investigated. The type of the complexes and their corresponding critical stability constants were evaluated by fitting the measured data using a self-developed algorithm. The pH and Nernst potential curve were calculated for the assumed complexes based on the law of mass action to find the best approximation. The correct definition of the occurring species is challenging and can lead to significant changes in the calculation of stability constants. For this reason, the measured silver potential curves were primarily used for the rating of the complexing agents. An evaluation of the measurements shows that the donor atom of the complexing agent and its ligand field strongly affected the stability and type of the complexes. Only a few complexing agents were found to be suitable for use in the cyanide-free silver electrolyte. [ABSTRACT FROM AUTHOR]

A new construction of a potentiometric sensor was introduced for the first time. It relies on the use of two membranes instead of one, as in the well-known coated-disc electrode. For this purpose, a new electrode body was constructed, including not one, but two glassy carbon discs covered with an ion-selective membrane. This solution allows for the sensor properties to be enhanced without using additional materials (layers or additives) on the membrane. The new construction is particularly useful for in situ measurements in environmental samples. Two ion-selective polymeric membranes were used, namely H+ and K+-selective membranes, to confirm the universality of the idea. The tests conducted included chronopotentiometric tests, electrochemical impedance spectroscopy, and potentiometric measurements. The electrical and analytical parameters of the sensors were evaluated and compared for all tested electrodes to evaluate the properties of the planar electrode versus previously known constructions. Research has shown that the application of two membranes instead of one allows for the resistance of an electrode to be lowered and for the electrical capacitance to be elevated. Improving the electrical properties of an electrode resulted in the enhancement of its analytical properties. The pH measurement range of the planar electrode is 2–11, which is much wider in contrast to that of the single-membrane electrode. The linear range of the K+-selective planar electrode is wider than that of the coated-disc electrode and equals 10−6 to 10−1 M. The response time turned out to be a few seconds shorter, and the potential drift was smaller due to the application of an additional membrane in the electrode construction. This research creates a new opportunity to design robust potentiometric sensors, as the presented construction is universal and can be used to obtain electrodes selective to various ions. [ABSTRACT FROM AUTHOR]

Two new surfactant sensors were developed by synthesizing Pt-doped acid-activated multi-walled carbon nanotubes (Pt@MWCNTs). Two different ionophores using Pt@MWCNTs, a new plasticizer, and (a) cationic surfactant 1,3-dihexadecyl-1H-benzo[d]imidazol-3-ium-DHBI (Pt@MWCNT-DHBI ionophore) and (b) anionic surfactant dodecylbenzenesulfonate-DBS (Pt@MWCNT-DBS ionophore) composites were successfully synthesized and characterized. Both surfactant sensors showed a response to anionic surfactants (dodecylsulfate (SDS) and DBS) and cationic surfactants (cetylpyridinium chloride (CPC) and hexadecyltrimethylammonium bromide (CTAB)). The Pt@MWCNT-DBS sensor showed lower sensitivity than expected with the sub-Nernstian response of ≈23 mV/decade of activity for CPC and CTAB and ≈33 mV/decade of activity for SDS and DBS. The Pt@MWCNT-DHBI surfactant sensor had superior response properties, including a Nernstian response to SDS (59.1 mV/decade) and a near-Nernstian response to DBS (57.5 mV/decade), with linear response regions for both anionic surfactants down to ≈2 × 10−6 M. The Pt@MWCNT-DHBI was also useful in critical micellar concentration (CMC) detection. Common anions showed very low interferences with the sensor. The sensor was successfully employed for the potentiometric titration of a technical grade cationic surfactant with good recoveries. The content of cationic surfactants was measured in six samples of complex commercial detergents. The Pt@MWCNT-DHBI surfactant sensor showed good agreement with the ISE surfactant sensor and classical two-phase titration and could be used as an analytical tool in quality control. [ABSTRACT FROM AUTHOR]

In this research, a coated graphite polyvinyl chloride (PVC) membrane electrode was fabricated for the potentiometric determination of lithium based on 13-(3-nitrophenyl)-12H,14H-benzo[g]chromeno[2,3-b]chromene-7,12,14(13H)-trione (L) as the ionophore. The best Nernstian response was observed from the membrane composition of 31% PVC, 7% L, 2% NaTPB, and 60% dioctyl phthalate (DOP) as the plasticizer. The designed sensor showed a wide linearity over the concentration range of 1 x 10-8-1 x 10-3 M with a slope of 60.2 ± 0.3 mV decade-1, and the limit of detection (LOD) of 7.5 x 10-9 M. The selectivity of the designed sensor was investigated by the matched potential method and no serious interference was observed. The response time and life span of the electrode were 5 s and 16 weeks, respectively. The potential response of the electrode was independent of solution pH in the pH range of 3.0-12.0. The influence of the presence of organic solvents on the potential response of the electrode was also scrutinized, and the results showed that the designed sensor keeps its Nernstian behavior in solutions with 20% non-aqueous content. In the end, the electrode was successfully applied to determine lithium carbonate in tablet, urine, and serum samples with recovery% values of 96.0 to 106.33 and RSD% 1.99-4.45. [ABSTRACT FROM AUTHOR]

The use of an electrochemical approach for assessment of the oxidative stress severity is a promising direction for point-of-care testing development, which is especially important for critically ill patients. The aim of this study was to determine the influence of different types of blood collection tubes (with clot activator and separating gel, lithium heparin, sodium citrate and K2EDTA) and storage conditions (at 25, 4 and -23 °C up to 5 days) on the electrochemical analysis of the antioxidant status of blood plasma, assessed by measuring the open circuit potential of platinum electrode (OCP) and antioxidant capacity via cyclic voltammetry method (q). It was obtained that blood collection tubes with lithium heparin and clot activator are the most suitable for the electrochemical analysis of antioxidant status of blood plasma, since they do not affect the results of measurements. Furthermore, data obtained during storage blood plasma samples in different temperature conditions indicate that it is preferable to perform electrochemical analysis in fresh samples. [ABSTRACT FROM AUTHOR]

Abstract Self‐powered pressure detection using smart wearable devices is the subject of intense research attention, which is intended to address the critical need for prolonged and uninterrupted operations. Current piezoelectric and triboelectric sensors well respond to dynamic stimuli while overlooking static stimuli. This study proposes a dual‐response potentiometric pressure sensor that responds to both dynamic and static stimuli. The proposed sensor utilizes interdigital electrodes with MnO2/carbon/polyvinyl alcohol (PVA) as the cathode and conductive silver paste as the anode. The electrolyte layer incorporates a mixed hydrogel of PVA and phosphoric acid. The optimized interdigital electrodes and sandpaper‐like microstructured surface of the hydrogel electrolyte contribute to enhanced performance by facilitating an increased contact area between the electrolyte and electrodes. The sensor features an open‐circuit voltage of 0.927 V, a short‐circuit current of 6 µA, a higher sensitivity of 14 mV/kPa, and outstanding cycling performance (>5000 cycles). It can accurately recognize letter writing and enable capacitor charging and LED lighting. Additionally, a data acquisition and display system employing the proposed sensor, which facilitates the monitoring of athletes’ rehabilitation training, and machine learning algorithms that effectively guide rehabilitation actions are presented. This study offers novel solutions for the future development of smart wearable devices.

This paper presents the development of a non-toxic and low-cost potassium ion sensor utilizing an Extended Gate Field-Effect Transistor (EGFET) configuration with all-solid-state electrodes fabricated on a printed circuit board (PCB) substrate. An Ag/AgCl-based pseudo-reference electrode (PRE) has been fabricated planar to a ion-selective membrane (ISM) coated on the gold solid-contact electrode (SCE). The PRE has shown $\lt 1~mV/day$ drift potential, exhibiting exceptional stability and reproducibility. While the SCE has demonstrated a high sensitivity of $49~mV/log[K^{+}]$ , covering a wide linear detection range from $10^{-4}~M$ to $1~M$ with a rapid response time of less than 10 seconds. The sensor has displayed minimal hysteresis ( $\lt 15~mV$ ) and remained stable over a broad pH range ( $pH~4$ to $pH~10$ ). These uni-planar, all-solid-state electrodes along with off-the-shelf FET mitigate the requirement of additional wire bonding by utilizing a common PCB platform for sensing as well as circuitry area. Additionally, the PRE, SCE and the FET in the EGFET-configuration-based sensing system have exhibited a high current sensitivity of $1.43~(\mu A)^{1/2}/log[K^{+}]$ . Our sensor presents a practical and reliable solution for soil nutrient measurement in precision agriculture, offering significant advantages over existing potassium sensors in terms of cost-effectiveness, sensitivity, stability, and environmental safety. The presented approach holds promise for optimizing agricultural productivity and minimizing environmental impact through efficient nutrient monitoring and smart irrigation and fertilization management systems.

Ensuring the long-term stability of screen-printed (SP) reference electrodes (REs) is increasingly essential because a major technical challenge in fabricating electrochemical sensors using screen printing is preparing an RE with a stable potential as it scales down in size. In this study, we fabricated SP electrodes that exhibit long-term stability in voltammetric and potentiometric experiments. The SP electrodes consisted of carbon working electrodes, a carbon counter electrode, an Ag/AgCl RE, and an ion-selective electrode (ISE) for detecting nitrate ions. The Ag/AgCl RE featured an electrolyte layer, a hydrophobic junction layer, and a small hole, collectively contributing to its long-term stability. This design achieved potential stability with minimal drift over extended periods in both 0.01 M PBS (pH 7.4) and 0.1 M Bis-tris (pH 6.5) buffer solutions. Additionally, the SP Ag/AgCl RE exhibited relatively low potential drift in the presence of various chemicals and different pH solutions. We analyzed the electrochemical behavior of two redox species, Fe(CN)63-/4− and Ru(NH3)62+/3+, using cyclic voltammetry and electrochemical impedance spectroscopy techniques at the SP electrodes. Potentiometric experiments confirmed the sensitivity, long-term stability, and selectivity of the SP ISE for nitrate ion detection, even in the presence of interfering ions.

The new era of solid contact ion selective electrodes (SC-ISEs) miniaturized design has received an extensive amount of concern. Because it eliminated the requirement for ongoing internal solution composition optimization and created a two-phase system with stronger detection limitations. Herein, the determination of venlafaxine HCl is based on a comparison study between different ion- to electron transduction materials (such as; multiwalled carbon nanotubes (MWCNTs), polyaniline (PANi), and ferrocene) and illustrating their mechanisms in their applied sensors. Their different electrochemical features (such as bulk resistance (Rb**), double-layer capacitance (Cdl), geometric capacitance (Cg), and specific capacitance (Cp)) were evaluated and discussed by using the Electrochemical Impedance Spectroscopy (EIS), Chronopotentiometry (CP), and Cyclic Voltammetry (CV) experiments. The results indicated that each transducer's influence on the proposed sensor's electrochemical characteristics is determined by their unique chemical and physical properties. The electrochemical features vary for different solid contact materials used in transduction mechanisms. The results confirm that the MWCNT sensor revealed the best electrochemical behavior with the potentiometric response of a near-Nernestian slope of 56.1 ± 0.8 mV/decade with detection limits of 3.8 × 10−6 mol/L (r2 = 0.999) and a low potential drift (∆E/∆t) of 34.6 µV/s. Also, the selectivity study was performed in the presence of different interfering species either in single or complex matrices. This demonstrates excellent selectivity, stability, conductivity, and reliability as a VEN-TPB ion pair sensor for accurately measuring VEN in its various formulations. The proposed method was compared to HPLC reported technique and confirmed no significant difference between them. So, the proposed sensors fulfill their solutions' demand features for VEN appraisal. [ABSTRACT FROM AUTHOR]

Skin cancer and other skin-related inflammatory pathologies are rising due to heightened exposure to environmental pollutants and carcinogens. In this context, natural products and repurposed compounds hold promise as novel therapeutic and preventive agents. Strengthening the skin's antioxidant defense mechanisms is pivotal in neutralizing reactive oxygen species (ROS) and mitigating oxidative stress. Sunset Yellow (SY) exhibits immunomodulatory characteristics, evidenced by its capacity to partially inhibit the secretion of proinflammatory cytokines, regulate immune cell populations, and modulate the activation of lymphocytes. This study aimed to investigate the antioxidant and anti-genotoxic properties of SY using in-silico, in vitro, and physiochemical test systems, and to further explore its potential role in 7,12-dimethylbenz(a) anthracene (DMBA)/ 12-o-tetradecanoylphorbol-13-acetate (TPA)-induced two-stage skin carcinogenesis. In vitro experiments showed that pre-treatment of SY significantly enhanced the cell viability of HaCaT cells when exposed to tertiary-Butyl Hydrogen Peroxide (tBHP). This increase was accompanied by reduced ROS levels, restoration of mitochondrial membrane potential, and notable reduction in DNA damage in (SY + tBHP) treated cells. Mechanistic investigations using DPPH chemical antioxidant activity test and potentiometric titrations confirmed SY's antioxidant properties, with a standard reduction potential ( E o ) of 0.211 V. Remarkably, evaluating the effect of topical application of SY in DMBA/TPA-induced two-step skin carcinogenesis model revealed dose-dependent decreases in tumor latency, incidence, yield, and burden over 21-weeks. Furthermore, computational analysis and experimental validations identified GSK3β, KEAP1 and EGFR as putative molecular targets of SY. Collectively, our findings reveal that SY enhances cellular antioxidant defenses, exhibits anti-genotoxic effects, and functions as a promising chemopreventive agent. [ABSTRACT FROM AUTHOR]

Organic ammonium and phosphonium salts exert excellent antimicrobial effects by interacting lethally with bacterial membranes. Particularly, quaternary ammonium lipids have demonstrated efficiency both as gene vectors and antibacterial agents. Here, aiming at finding new antibacterial devices belonging to both classes, we prepared a water-soluble quaternary ammonium lipid (6) and a phosphonium salt (1) by designing a synthetic path where 1 would be an intermediate to achieve 6. All synthesized compounds were characterized by Fourier-transform infrared spectroscopy and Nuclear Magnetic Resonance. Additionally, potentiometric titrations of NH3+ groups 1 and 6 were performed to further confirm their structure by determining their experimental molecular weight. The antibacterial activities of 1 and 6 were assessed first against a selection of multi-drug-resistant clinical isolates of both Gram-positive and Gram-negative species, observing remarkable antibacterial activity of both compounds against Gram-positive isolates of Enterococcus and Staphylococcus genus. Further investigations on a wider variety of strains of these species confirmed the remarkable antibacterial effects of 1 and 6 (MICs = 4–16 and 4–64 µg/mL, respectively), while 24 h-time-killing experiments carried out with 1 on different S. aureus isolates evidenced a bacteriostatic behavior. Moreover, both compounds 1 and 6, at the lower MIC concentration, did not show significant cytotoxic effects when exposed to HepG2 human hepatic cell lines, paving the way for their potential clinical application. [ABSTRACT FROM AUTHOR]

[Display omitted] Manipulating metal valence states and porosity in the metal–organic framework (MOF) by alloying has been a unique tool for creating high-valent metal sites and pore environments in a structure that are inaccessible by other methods, favorable for accelerating the catalytic activity towards sensing applications. Herein, we report Fe3+-driven formation of catalytic active Ni3+ species in the amine-crafted benzene-dicarboxylate (BDC-NH 2)-based MOF as a high-performance electrocatalyst for glucose sensing. This work took the benefit of different bonding stability between BDC-NH 2 ligand, and Fe3+ and Ni2+ metal precursor ions in the heterometallic Ni x Fe (1- x) -BDC-NH 2 MOF. The FeCl 3 that interacts weakly with ligand, oxidizes the Ni2+ precursor to Ni3+-based MOF owing to its Lewis acidic behavior and was subsequently removed from the structure supported by Ni atoms, during solvothermal synthesis. This enables to create mesopores within a highly stable Ni-MOF structure with optimal feed composition of Ni 0.7 Fe 0.3 -BDC-NH 2. The Ni3+-based Ni 0.7 Fe 0.3 -BDC-NH 2 demonstrates superior catalytic properties towards glucose sensing with a high sensitivity of 13,435 µA mM−1 cm−2 compared to the parent Ni2+-based Ni-BDC-NH 2 (10897 μA mM−1 cm−2), along with low detection limit (0.9 μM), short response time (≤5 s), excellent selectivity, and higher stability. This presented approach for fabricating high-valent nickel species, with a controlled quantity of Fe3+ integrated into the structure allowing pore engineering of MOFs, opens new avenues for designing high-performing MOF catalysts with porous framework for sensing applications. [ABSTRACT FROM AUTHOR]

Electrodeposited amorphous hydrated iridium oxide (IrOx) is a promising material for pH sensing due to its high sensitivity and the ease of fabrication. However, durability and variability continue to restrict the sensor's effectiveness. Variation in probe films can be seen in both performance and fabrication, but it has been found that performance variation can be controlled with potentiostatic conditioning (PC). To make proper use of this technique, the morphological and chemical changes affecting the conditioning process must be understood. Here, a thorough study of this material, after undergoing PC in a pH-sensing-relevant potential regime, was conducted by voltammetry, scanning electron microscopy (SEM), energy-dispersive X-ray spectroscopy (EDS), X-ray diffraction (XRD), and X-ray photoelectron spectroscopy (XPS). Fitting of XPS data was performed, guided by raw trends in survey scans, core orbitals, and valence spectra, both XPS and UPS. The findings indicate that the PC process can repeatably control and conform performance and surface bonding to desired calibrations and distributions, respectively; PC was able to reduce sensitivity and offset ranges to as low as ±0.7 mV/pH and ±0.008 V, respectively, and repeat bonding distributions over ~2 months of sample preparation. Both Ir/O atomic ratios (shifting from 4:1 to over 4.5:1) and fitted components assigned hydroxide or oxide states based on the literature (low-voltage spectra being almost entirely with suggested hydroxide components, and high-voltage spectra almost entirely with suggested oxide components) trend across the polarization range. Self-consistent valence, core orbital, and survey quantitative trends point to a likely mechanism of ligand conversion from hydroxide to oxide, suggesting that the conditioning process enforces specific state mixtures that include both theoretical Ir(III) and Ir(IV) species, and raising the conditioning potential alters the surface species from an assumed mixture of Ir species to more oxidized Ir species. [ABSTRACT FROM AUTHOR]

Drug plant raw materials represent an important source of biologically active substances (BASs), which are used in pharmaceutical, cosmetic, food, and other industries. This paper presents the results of studying colloidal properties of crushed sophora Japanese fruits (hereinafter referred to as sophora) in order to improve the extraction of BASs. To achieve the goal, the following tasks have been set: the study of the ζ potential of sophora particles at different times of contact between the particles and an extractant and the pH values of the medium; determining the isoelectric point (IEP) of the sophora particles by electrophoresis; finding the point of zero charge (PZC) of sophora particles using potentiometric titration; and studying the influence of medium pH, sophora particle size, temperature, the presence of surfactants and ions, and the nature of an extractant on sophora swelling. The points of zero charge ) of the aqueous dispersions of sophora and extracted flavonoids are 5.8 and 5.2, respectively, thus being close to the values . The swelling of sophora particles is limited and accompanied by the gradual fracture of the plant cells. Adsorption equilibrium is achieved within 30 min. In an alkaline region and in the presence of alcohol, the swelling of the sophora particles decreases, while it increases at elevated temperature and in the presence of NaI ions. [ABSTRACT FROM AUTHOR]

The reaction of the vanadyl ion (VO2+) with imidazole-4-carboxylic acid (Im4COOH), imidazole-2-carboxylic acid (Im2COOH) and methylimidazole-2-carboxylic acid (MeIm2COOH), respectively, in the presence of small bioligands (bL) [oxalate (Ox), lactate (Lact), citrate (Cit) and phosphate (Phos)] and high-molecular-weight (HMW) human serum proteins [albumin (HSA) and transferrin (hTf)] were studied in aqueous solution using potentiometric acid–base titrations. The species distribution diagrams for the high-molecular-mass (HMM) proteins with oxidovanadium(IV) under physiological pH were dominated by VO(HMM)2, VOL(HMM) for unsubstituted ligands (L− = Im4COO− and Im2COO−). However, for the N-substituted MeIm2COOH, the species distribution diagrams under physiological pH were dominated by VOL2, VO(HMM)2 and VO2L2(HMM). These species were further confirmed by LC-MS, MALDI-TOF-MS and EPR studies. The glucose-stimulated insulin secretion (GSIS) action of the complexes was investigated using INS-1E cells at a 1 µM concentration, which was established through cytotoxicity studies via the MTT assay. The neutral complexes, especially VO(MeIm2COO)2, showed promising results in the stimulation of insulin secretion than the cationic [VO(MeIm2CH2OH)2]2+ complex and the vanadium salt. Oxidovanadium(IV) complexes reduced insulin stimulation significantly under normoglycaemic levels but showed positive effects on insulin secretion under hyperglycaemic conditions (33.3 mM glucose media). The islets exposed to oxidovanadium(IV) complexes under hyperglycaemic conditions displayed a significant increase in the stimulatory index with 1.19, 1.75, 1.53, 1.85, 2.20 and 1.29 observed for the positive control (sulfonylurea:gliclazide), VOSO4, VO(Im4COO)2, VO(Im2COO)2, VO(MeIm2COO)2 and VO(MeIm2CH2OH)22+, respectively. This observation showed a potential further effect of vanadium complexes towards type 2 diabetes and has been demonstrated for the first time in this study. [ABSTRACT FROM AUTHOR]

The adsorption of divalent ions on metal oxides is controlled by the pH of a solution. It is commonly assumed that this is a reversible process for pH changes. However, there are reports that the sorption of ions on oxides may not be reversible. To verify this, we used potentiometric titration, ion-selective electrodes (ISEs), and electrokinetic measurements to examine the reversibility of the adsorption of hydrogen ions and three metal ions (Ca2+, Cu2+, and Fe2+) on TiO2. The ferrous ion was used as a reference because its adsorption is entirely irreversible. The surface charge determined by potentiometric titration and the adsorption edges measured using ISE indicate that the adsorption of copper ions is reversible with changes in pH. In the case of calcium ions, the results suggest a certain degree of irreversibility. There are apparent differences in the electrokinetic potential data obtained during titration with base and acid, which suggests that the adsorption is irreversible. We have explained this contradiction by considering the complex and dynamic nature of electrophoretic mobility. In our opinion, potentiometric titration may be the simplest and most reliable method for assessing the reversibility of multivalent ion adsorption. [ABSTRACT FROM AUTHOR]

The chemical speciation of binary and ternary VO2+-picolinic acid (HPic) complexes with the amino acids: Leucine (Leu, HL), Isoleucine (Ile, HL), Valine (Val, HL), Tryptophan (Thr, HL), Glutamine (Gln, HL), Lysine (Lys, HL), Arginine (Arg, HL) and Tyrosine (Tyr, H2L) were obtained. This study was performed by potentiometric titrations at 25 °C using 1.0 mol·dm−3 NaCl as the ionic medium. The experimental data were analyzed with the least squares program LETAGROP, and the respective distribution diagrams were obtained with the HYSS program. The relative stability parameters Δlog10K, log10X and %R.S were determined. [ABSTRACT FROM AUTHOR]

Effects of dry and wet grind on peanut oil and protein yield, oil bodies (OBs) stability, fatty acid composition, protein composition and functional characteristics were systematically analyzed. Results showed that peanut oil and protein yields reached highest at dry grind 90 s (92.56% and 83.05%, respectively), while peanut oil and protein yields were 94.58% and 85.36%, respectively, at wet grind 120 s. Peanut oil and protein yields by wet grind was 2.18% and 2.78% higher than that of dry grind, respectively. Surface protein concentration (Г) and absolute value of zeta potential of OBs extracted by wet grind (WOBs) were 11.53 mg/m2 and 18.51 mV, respectively, which were higher than OBs extracted by dry grind (DOBs), indicating stability of WOBs was higher than DOBs. Relative contents of oleic acid and linoleic acid in peanut oil, essential and hydrophobic amino acids in protein extracted by wet grind were higher than dry grind. There was little difference in protein composition between wet and dry grind, but thermal denaturation degree of protein obtained by wet grind was lower than dry grind. Solubility, oil retention, emulsion stability, foaming and foam stability of protein obtained by wet grind were better than dry grind. Results from this study provided theoretical basis for grind pretreatment selection of aqueous enzymatic method. [ABSTRACT FROM AUTHOR]

The shelf life of a food product is a limited period of time after production and packaging, during which it maintains the necessary and acceptable level of quality for final consumption. The aim of the research was to predict the shelf life of chocolate packaged in two bilaminated containers with respect to peroxide value, using accelerated testing and constant relative humidity. The peroxide value was evaluated by potentiometric titration. The order of the reaction was defined and with the Arrhenius model the degradation rate constant was found for each container and temperature of study. Shelf life was determined with the kinetic equation of oxidation compound formation at 5, 20 and 35℃ at 217, 114 and 64 days for the 20 microns (μ) packages, and 114, 95 and 81 days for the 50 μ packages respectively. It is concluded that the 20 μ packaging between a storage temperature of 15 and 18℃ is the suggested packaging with a shelf life between 141 and 124 days. The results would enable those working in the chocolate manufacturing and packaging industry to take the temperatures and types of packaging studied as a reference in their production. [ABSTRACT FROM AUTHOR]

This study has introduced a pioneering methodology by employing biochars as a basic carbocatalyst in the context of multicomponent reactions. Biochars were produced from different manures and organic wastes using the pyrolysis-carbonization process under limited oxygen conditions. The prepared biochars were well characterized using Fourier transform infrared spectroscopy (FT-IR), scanning electron microscopy (SEM), energy-dispersive X-ray spectroscopy (EDX), Brunauer–Emmett–Teller (BET) analysis, and powder X-ray diffraction (XRD). The chemical characteristics and potentiometric titration analysis provide compelling evidence of the intriguing basicity properties exhibited by the prepared biochars. The pH values, ash content, and potentiometric titration results confirmed the exceptional basicity characteristics of cow manure biochar formed at 600 oC (CB600), establishing it as the most basic carbocatalyst in this study. Encouraged by these initial results, the activity of the biochars as basic carbocatalysts was evaluated in multicomponent synthesis of 4H-benzo[h]chromene and pyranopyrazoles and 600 °C exhibited the most pronounced catalytic performance owing to its superior total basicity. By these findings, it can be asserted that this work introduces the groundbreaking application of biochars as potent basic carbocatalysts for the multicomponent synthesis of structurally diverse heterocycles. Unveiling the vital basic role of biochars will definitely open up new opportunities in organic chemistry and provide salient features for environmentally-friendly chemistry, including easy retrieval, non-toxicity, and widespread accessibility. Highlights: Biochars were introduced as potent basic carbocatalysts for multicomponent synthesis of heterocycles. Quantitatively assess basicity of the prepared biochars was performed using potentiometric titration. The activity of the biochars as basic carbocatalysts was evaluated in multicomponent synthesis of chromenes and pyranopyrazoles. [ABSTRACT FROM AUTHOR]

Total alkalinity (AT) and dissolved inorganic carbon (CT) in the oceans are important properties with respect to understanding the ocean carbon cycle and its link to global change (ocean carbon sinks and sources, ocean acidification) and ultimately finding carbon-based solutions or mitigation procedures (marine carbon removal). We present a database of more than 44 400 AT and CT observations along with basic ancillary data (spatiotemporal location, depth, temperature and salinity) from various ocean regions obtained, mainly in the framework of French projects, since 1993. This includes both surface and water column data acquired in the open ocean, coastal zones and in the Mediterranean Sea and either from time series or dedicated one-off cruises. Most AT and CT data in this synthesis were measured from discrete samples using the same closed-cell potentiometric titration calibrated with Certified Reference Material, with an overall accuracy of ±4 µ mol kg -1 for both AT and CT. The data are provided in two separate datasets – for the Global Ocean and the Mediterranean Sea (10.17882/95414, Metzl et al., 2023), respectively – that offer a direct use for regional or global purposes, e.g., AT –salinity relationships, long-term CT estimates, and constraint and validation of diagnostic CT and AT reconstructed fields or ocean carbon and coupled climate–carbon models simulations as well as data derived from Biogeochemical-Argo (BGC-Argo) floats. When associated with other properties, these data can also be used to calculate pH, the fugacity of CO 2 (f CO 2) and other carbon system properties to derive ocean acidification rates or air–sea CO 2 fluxes. [ABSTRACT FROM AUTHOR]

The present work describes the complexation of the anti-inflammatory sialorphin derivative Pal-Lys-Lys-Gln-His-Asn-Pro-Arg (palmitic acid-lysine-lysine-glutamine-histidine-asparagine-proline-arginine) with Cu(II) ions in an aqueous solution, at a temperature of 25.0 ± 0.1 °C, over the whole pH range. The complexing properties were characterized by potentiometric and UV-Vis spectrophotometric methods. The potentiometric method was used to calculate the logarithms of the overall stability constants (log β) and the values of the stepwise dissociation constants (pKa) of the studied complexes. The percentage of each species formed in an aqueous solution was estimated from the species distribution curve as a function of pH. The absorbance (A) and molar absorption coefficient (ε) values for the Cu(II)-sialorphin derivative system were determined with UV-Vis spectroscopy. Our studies indicate that the sialorphin derivative forms stable complexes with Cu(II) ions, which may lead to future biological and therapeutic applications. [ABSTRACT FROM AUTHOR]

The fabrication of ion-selective electrodes (ISEs) via printing technologies such as screen-printing, inkjet printing, and 3D printing is attracting increasing attention due to the superb reproducibility and scalability of these technologies. In contrast to traditional manual casting, coating, and assembling procedures often used in research labs, printing methods are much more compatible with manufacturing processes in industry and, therefore, are easier to scale up. In this paper, we first summarized and compared the printing mechanisms and ink requirements of screen printing, inkjet printing, and 3D printing technologies. Then we present an overview of how different printing technologies can create sensor components, such as electrical contact layers, ion-to-electron transduction layers, ion sensing membranes, reference electrode membranes, insulation layers, and microfluidic/detection housings. The printing protocol, ink material, and sensor performance are highlighted for a few selected ISEs. This review concludes with a summary of the advantages and drawbacks of various printing technologies.

Abstract Phosphate is an important fertilizer in agriculture and electrochemical sensors based on cobalt (Co) are promising for measurement of phosphate. The deposition of Co onto conductive substrates to form a nano/microstructured Co layer with rich active sites is a typical strategy to improve detection performances. However, the widely used substrates show smooth surfaces, which cannot provide extra active sites. Herein, a high‐performance phosphate sensor is fabricated by generating Co nanoparticles (NPs) on a hierarchically porous laser‐induced graphene (LIG) matrix with a large surface area. Specifically, a Co layer is first electroplated on the LIG matrix. Nevertheless, the pores of LIG will be blocked by the dense Co layer so the performances of the fabricated LIG‐Co sensor exhibit limited enhancements. Therefore, a “nearly all etching (NAE)” technique is developed to transform the dense Co layer to dispersive Co NPs and re‐expose the pores of LIG, both increasing the active sites. Compared to the LIG‐Co sensor, the LIG‐Co NP sensor displays overall superiority. The response time, sensitivity, and linearity are enhanced from ≈60 to ≈10 s, from 0.012 to 0.069 V dec−1, and from 0.973 to 0.998, respectively. The LIG‐Co NP sensor also shows a decent anti‐interference capability.

This study focused on developing an advanced bitterness sensor designed to minimize interference from common anions such as nitrate (NO3−) and iodide (I−) by incorporating partially dissociated amine compounds into the sensor membrane. The conventional bitter sensor (C00) uses fully dissociated quaternary ammonium salt tetradecyl ammonium bromide (TDAB), which typically exhibits high responses to these anions, leading to inaccurate bitterness assessments. To address this issue, we explored the use of three partially dissociated amines—oleylamine (OAm), dioctadecylamine (DODA), and tridodecylamine (TDA)—as lipids in the membrane components. We fabricated sensor membranes and tested their ion selectivity, interference resistance to anion, and sensitivity to iso-alpha acids (IAAs), representative bitter compounds in beer. The results showed that the membranes with partially dissociated amines significantly reduced anion interference. Notably, the sensitivity of the TDA membrane to IAAs was 80.4 mV/dec in concentration, exceeding the 68.5 mV/dec of the TDAB membrane. This enhanced sensitivity, coupled with reduced anion interference, reveals a novel property of partially dissociated lipids in taste sensors, distinguishing them from fully dissociated lipids. These findings pave the way for the development of sensors that can accurately assess a bitter taste and have potential applications in the food and beverage industry.

Carbon nanomaterials were introduced into this research as modifiers for polymeric membranes for single-piece electrodes, and their properties were studied for the case of nitrate-selective sensors. The use of graphene, carbon black and carbon nanotubes is shown to significantly improve the potentiometric response, while no redox response was observed. The use of carbon nanomaterials results in a near-Nernstian response (54 mV/pNO3−) towards nitrate ions over a wide linear range (from 10−1 to 10−6 M NO3−). The results obtained by chronopotentiometry and electrochemical impedance spectroscopy reveal little resistance, and the capacitance parameter is as high as 0.9 mF (for graphene-based sensor). The high electrical capacity of electrodes results in the good stability of the potentiometric response and a low potential drift (0.065 mV/h). Introducing carbon nanomaterials into the polymetric membrane, instead of using them as separate layers, allows for the simplification of the sensors’ preparation procedure. With single-piece electrodes, one step of the procedure could be omitted, in comparison to the procedure for the preparation of solid-contact electrodes.

Under ideal conditions, nanotubes with a fixed negative tube-wall charge will reject anions and transport-only cations. Because many proposed nanofluidic devices are optimized in this ideally cation-permselective state, it is important to know the experimental conditions that produce ideal responses. A parameter called Ccrit, the highest salt concentration in a contacting solution that still produces ideal cation permselectivity, is of particular importance. Pioneering potentiometric studies on gold nanotubes were interpreted using an electrostatic model that states that Ccrit should occur when the Debye length in the contacting salt solution becomes equivalent to the tube radius. Since this “double-layer overlap model” (DLOM), treats all same-charge ions as identical point charges, it predicts that all same-charged cations should produce the same Ccrit. However, the effect of cation on Ccrit in gold nanotubes was never investigated. This knowledge gap has become important because recent studies with a polymeric cation-permselective nanopore membrane showed that DLOM failed for every cation studied. To resolve this issue, we conducted potentiometric studies on the effect of salt cation on Ccrit for a 10 nm diameter gold nanotube membrane. Ccrit for all cations studied were, within experimental error, the same and identical, with values predicted by DLOM. The reason DLOM prevailed for the gold nanotubes but failed for the polymeric nanopores stems from the chemical difference between the fixed negative charges of these two membranes.

Solid-contact ion-selective electrodes (SC-ISEs) have the advantages of easy miniaturization, even chip integration, easy carrying, strong stability, and more favorable detection in complex environments. They have been widely used in conjunction with portable, wearable, and intelligent detection devices, as well as in on-site analysis and timely monitoring in the fields of environment, industry, and medicine. This article provides a comprehensive review of the composition of sensors based on redox capacitive and double-layer capacitive SC-ISEs, as well as the ion–electron transduction mechanisms in the solid-contact (SC) layer, particularly focusing on strategies proposed in the past three years (since 2021) for optimizing the performance of SC-ISEs. These strategies include the construction of ion-selective membranes, SC layer, and conductive substrates. Finally, the future research direction and possibilities in this field are discussed and prospected.