Search

NIO1 is a compact and flexible radiofrequency H- ion source, developed by Consorzio RFX and INFN-LNL. Aim of the experimentation on NIO1 is the optimization of both the production of negative ions and their extraction and beam optics. In the initial phase of its commissioning, NIO1 was operated with nitrogen, but now the source is regularly operated also with hydrogen. To evaluate the source performances an optical emission spectroscopy diagnostic was installed. The system includes a low resolution spectrometer in the spectral range of 300-850 nm and a high resolution (50 pm) one, to study respectively the atomic and the molecular emissions in the visible range. The spectroscopic data have been interpreted also by means of a collisional-radiative model developed at IPP Garching. Besides the diagnostic hardware and the data analysis methods, the paper presents the first plasma measurements across a transition to the full H mode, in a hydrogen discharge. The characteristic signatures of this transition in the plasma parameters are described, in particular the sudden increase of the light emitted from the plasma above a certain power threshold., 3 pages, 2 figures. Contributed paper for the ICIS 2015 conference. Accepted manuscript

The PRIMA project aims at the construction of two ITER-NBI facilities in Padova (Italy). The first one is called SPIDER which is negative H/D 100 keV RF source, while the second one (MITICA) will be a full scale 1 MeV deuterium beam injector as the one that will be used in ITER. In order to resolve the horizontal beam intensity profile in MITICA and one of the eight beamlets groups in SPIDER, the Close-contact Neutron Emission Surface Mapping (CNESM) system is being developed. The goal of this device is to reconstruct the D− beam evaluating the map of the neutron emission due to interaction of the deuterium beam with the deuterons implanted in the beam dump surface. For this reason, the CNESM diagnostic, which is based on nGEM detectors for fast neutrons, will be placed right behind the SPIDER and MITICA beam dump, i.e. in an UHV (Ultra High Vacuum) environment. Since the nGEM detectors need to operate at atmospheric pressure a vacuum sealed detector box has been designed to be installed inside the vacuum vessel and able to sustain atmospheric pressure inside. This paper describes the status of the CNESM diagnostic and underlines the different phases followed during the realization and installation of the diagnostic on the SPIDER beam dump as well as its imaging performances.

To reach fusion conditions and control the plasma configuration in ITER, the next step in tokamak fusion research, two neutral beam injectors (NBIs) will supply 16.5 MW each, by neutralizing accelerated negative hydrogen or deuterium ions. The requirements of ITER NBIs (40A/1 MeV D- ions for ≤1 h, 46A/870 keV H- ions for ≤1000 s) have never been simultaneously attained. So in the Neutral Beam Test Facility (NBTF, Consorzio RFX, Italy) the operation of the full-scale ITER NBI prototype (MITICA) will be tested and optimised up to full performances, focussing on accelerator (including voltage holding), beam optics, neutralisation, residual ion removal. The NBTF includes also the full-scale prototype of the ITER NBI source with 100 keV particle energy (SPIDER), for early investigation of: negative ion production and extraction, source uniformity, negative ion current density and beam optics. This paper will describe the main results of the first two years of SPIDER operation, devoted to characterizing plasma and beam parameters, including investigation of RF-plasma coupling efficiency and magnetic filter field effectiveness in reducing co-extracted electrons. SPIDER is progressing towards the first caesium injection, which aims at increasing the negative ion density. A major shutdown, planned for 2021, to solve the issues identified during the operation and to carry out programmed modifications, will be outlined. The installation of each MITICA power supply and auxiliary system is completed; in-vessel mechanical components are under procurement by Fusion for Energy (F4E). Integration, commissioning and test of the power supplies, procured by F4E and QST, as the Japanese Domestic Agency (JADA), will be presented. In particular, 1.0MV insulating tests were carried out step-by-step and successfully completed. In 2020 integrated tests of the power supplies on the accelerator dummy load started, including the assessment of their resilience to accelerator grid breakdowns using a short-circuit device located in vacuum. The aggressive programme, to validate the NBI design at NBTF and to meet ITER schedule (requiring NBIs in operation in 2032), will be outlined. Unfortunately, in 2020 the coronavirus disease infection affected the NBTF activities. A solution to proceed with integrated power tests despite the coronavirus is presented.

Heating neutral beam (HNB) injectors, necessary to achieve burning conditions and to control plasma instabilities in ITER, are characterized by such demanding parameters that a neutral beam test facility (NBTF) dedicated to their development and optimization is being realized in Padua (Italy) with direct contributions from the Italian government (through Consorzio RFX as the host entity) and the ITER international organization (with kind contributions from the ITER domestic agencies of Europe, Japan and India) and technical and scientific support from various European laboratories and universities. The NBTF hosts two experiments: SPIDER, devoted to ion source optimization for the required source performance, and MITICA, the full-size prototype of the ITER HNB, with an ion source identical to SPIDER. This paper gives an overview of the progress towards NBTF realization, with particular emphasis on issues discovered during this phase of activity and on solutions adopted to minimize the impact on the schedule and maintain the goals of the facilities. The realization of MITICA is well advanced; operation is expected to start in 2023 due to the long procurement time of the in-vessel mechanical components. The beam source power supplies, operating at 1 MV, are in an advanced phase of realization; all high-voltage components have been installed and the complex insulation test phase began in 2018. At the same time, construction and installation of SPIDER plant systems was successfully completed with their integration into the facility. The mechanical components of the SPIDER ion source were installed inside the vessel and connected to the plants. Integrated commissioning with the control, protection and safety systems ended positively and the first experimental phase has begun. The first results of the SPIDER experiment, with data from operational diagnostics, and the plans for the 1 MV insulation tests on the MITICA high-voltage components are presented.

Nell’agosto del 1961, a Zagabria per la mostra nove tendencije, si riunì un gruppo di artisti, provenienti da diverse aree culturali: italiana, francese e tedesca. Le neoavanguardie così costituitesi erano maturate nello stesso ambiente culturale, quello della rivista “Čovjek i Prostor” (Uomo e spazio), che era stato un laboratorio anche per l’attività critica di Vera Horvat Pintarić (1926) e principalmente di Matko Meštrović (1933) e Radoslav Putar (1929-1994). Osservando i nuovi fermenti artistici di ambito italiano, francese e tedesco, questi ultimi due studiosi contribuirono, ognuno con un peso diverso, a elaborare l’ideologia originaria della manifestazione internazionale di nove tendencije.

The ITER project requires additional heating by two neutral beam injectors, each accelerating up to 1 MV a 40 A beam of negative deuterium ions for one hour. Such requirements have never been reached, so it was decided to build in Padova a facility (PRIMA) that hosts two experimental devices: SPIDER, a 100 kV negative H/D RF beam source, and MITICA, a full-scale injector for the ITER NBI. SPIDER has begun operation in 2018, while MITICA is expected to start after 2020. In both devices the accelerated deuterium beam impinges on an actively cooled beam dump used to stop the deuterons. Detection of fusion neutrons produced between beam–deuterons and dump-embedded deuterons will be used as a means to resolve the horizontal beam intensity profile. A neutron detection system called Close-contact Neutron Emission Surface Mapping (CNESM) is installed right behind the SPIDER beam dump, with the aim to provide the neutron emission map of the beam dump surface. The core of this diagnostic system is an nGEM (neutron-Gas Electron Multiplier) detector which will be able to reconstruct the fast neutron beam profile with an efficiency of about 10−4. A crucial point in order to correctly reconstruct the profile of the deposited D − power is the directionality discrimination capability of the detector. This paper reports on the results of the characterization of the nGEM directionality capabilities, performed at the Frascati Neutron Generator (FNG) using 2.5 MeV neutrons, before installation of the detector inside the SPIDER vacuum vessel.

The ITER neutral beam test facility under construction in Padova will host two experimental devices: SPIDER, a 100 kV negative H/D RF beam source, and MITICA, a full scale, 1 MeV deuterium beam injector . SPIDER will start operations in 2016 while MITICA is expected to start during 2019. Both devices feature a beam dump used to stop the produced deuteron beam. Detection of fusion neutrons produced between beam-deuterons and dump-implanted deuterons will be used as a means to resolve the horizontal beam intensity profile. The neutron detection system will be placed right behind the beam dump, as close to the neutron emitting surface as possible thus providing the map of the neutron emission on the beam dump surface. The system uses nGEM neutron detectors . These are Gas Electron Multiplier detectors equipped with a cathode that also serves as neutron–proton converter foil. The cathode is designed to ensure that most of the detected neutrons at a point of the nGEM surface are emitted from the corresponding beamlet footprint (with dimensions of about 40×22 mm2) on the dump front surface. The size of the nGEM detector for SPIDER is 352 mm×200 mm. Several smaller size prototypes have been successfully made in the last years and the experience gained on these detectors has led to the production of the full size detector for SPIDER during 2014. This nGEM has a read-out board made of 256 pads (arranged in a 16×16 matrix) each with a dimension of 22 mm×13 mm. This paper describes the production of this detector and its tests (in terms of beam profile reconstruction capability, uniformity over the active area, gamma rejection capability and time stability) performed on the ROTAX beam-line at the ISIS spallation source (Didcot-UK).

Neutral beam injection (NBI) for plasma heating and current drive is necessary for International Thermonuclear Experimental reactor (ITER) tokamak. Due to its various advantages, a radio frequency (RF) driven plasma source type was selected as a reference ion source for the ITER heating NBI. The ITER relevant RF negative ion sources are inductively coupled (IC) devices whose operational working frequency has been chosen to be 1 MHz and are characterized by high RF power density (~9.4 W cm−3) and low operational pressure (around 0.3 Pa). The RF field is produced by a coil in a cylindrical chamber leading to a plasma generation followed by its expansion inside the chamber. This paper recalls different concepts based on which a methodology is developed to evaluate the efficiency of the RF power transfer to hydrogen plasma. This efficiency is then analyzed as a function of the working frequency and in dependence of other operating source and plasma parameters. The study is applied to a high power IC RF hydrogen ion source which is similar to one simplified driver of the ELISE source (half the size of the ITER NBI source).

The realization of the ITER Neutral Beam Test Facility (NBTF) and the start the experimental phase are important tasks of the fusion roadmap, since the target requirements of injecting to the plasma a beam of Deuterium atoms with a power up to 16.5 MW, at 1MeV of energy and with a pulse length up to 3600s have never been reached together before. The ITER NBTF, called PRIMA (Padova Research on ITER Megavolt Accelerator), is hosted in Padova, Italy; it includes two experiments: MITICA, the full-scale prototype of the ITER injector and SPIDER, the full-size negative ion source. The realization promoted by the ITER organization is carried out with the contribution of the European Union, channeled through the Joint Undertaking for ITER (F4E), of the Consorzio RFX which hosts the Test Facility, the Japanese and the Indian ITER Domestic Agencies (JADA and INDA) and several European laboratories, such as IPP-Garching, KIT-Karlsruhe, CCFECulham, CEA-Cadarache. The early start of operation of PRIMA experiments is urgent because sufficient experimental time is necessary to face and solve the issues related to the achievement of the desired performance in time for the ITER operation, requiring NBI since the beginning. Substantial progresses have been recently achieved: the buildings construction, begun in October 2012, has been completed by the end of 2015 and the installation of some components has been started since the end of 2014. The SPIDER realization is well advanced: the installation phase is proceeding in good agreement with the general plan; it is expected to be almost completed by the end of 2016. In parallel, the commissioning of the SPIDER power supply (PS) and auxiliary plant systems is being proceeding. Tests at full power and remote control are planned, including also those addressed to reproduce the grid breakdowns and to test the relevant protections. The design of the MITICA injector components was completed in 2015their procurement is being made through a number of tenders, some of them already launched. The HV Power Supply system of the MITICA 1MV accelerator, provided by JADA, was delivered on site in December 2015. The challenging installation of these components, including the step-up transformers and the SF6 gas insulated transmission line, started soon after and will go on throughout 2016. The present phase, with the PRIMA buildings continuously filled with new components, with the installation activities progressing and with also the commissioning and testing phase starting represents a substantial step forward toward the main target. The paper will describe the main challenges the Project Team has dealt during this phase and the important feedback derived for the ITER HNB systems both from the technical and the organizational standpoints.

SPIDER is one of two projects of the ITER Neutral Beam Test Facility under construction in Padova, Italy, at the Consorzio RFX premises. It will have a 100 keV beam source with a full-size prototype of the radiofrequency ion source for the ITER neutral beam injector (NBI) and also, similar to the ITER diagnostic neutral beam, it is designed to operate with a pulse length of up to 3600 s, featuring an ITER-like magnetic filter field configuration (for high extraction of negative ions) and caesium oven (for high production of negative ions) layout as well as a wide set of diagnostics. These features will allow a reproduction of the ion source operation in ITER, which cannot be done in any other existing test facility. SPIDER realization is well advanced and the first operation is expected at the beginning of 2018, with the mission of achieving the ITER heating and diagnostic NBI ion source requirements and of improving its performance in terms of reliability and availability. This paper mainly focuses on the preparation of the first SPIDER operations - integration and testing of SPIDER components, completion and implementation of diagnostics and control and formulation of operation and research plan, based on a staged strategy

In spite of the wide use of RF sources, a complete understanding of the mechanisms regulating the RF-coupling of the plasma is still lacking so self-consistent simulations of the involved physics are highly desirable. For this reason we are developing a 2.5D fully kinetic Particle-In-Cell Monte-Carlo-Collision (PIC-MCC) model of a cylindrical ICP-RF source, keeping the time step of the simulation small enough to resolve the plasma frequency scale. The grid cell dimension is now about seven times larger than the average Debye length, because of the large computational demand of the code. It will be scaled down in the next phase of the development of the code. The filling gas is Xenon, in order to minimize the time lost by the MCC collision module in the first stage of development of the code. The results presented here are preliminary, with the code already showing a good robustness. The final goal will be the modeling of the NIO1 (Negative Ion Optimization phase 1) source, operating in Padua at Consorzio RFX.

The deployment of neutral beam injectors in future fusion plants is beset by the particularly poor efficiency of the neutralization process. Beam-generated plasma neutralizers were proposed as a passive and intrinsically safe scheme of efficient plasma neutralizers. The concept is based on the natural ionization of the gas target by the beam, and on a suitable confinement of the secondary plasma. The technological challenge of such a concept is the magnetic confinement of the secondary plasma: a proof-of-principle for the concept is needed. The possibility to test of such a system in the small negative ion beam system NIO1 is discussed in this paper. The constraints given by the facility are first discussed. A model of beam-gas interaction is developed to provide the charge-state of beam particles along the neutralizer, and to provide the source terms of plasma generation. By using a cylindrical model of plasma diffusion in magnetic fields, the ionization degree of the target is estimated. In the absence of magnetic fields the diffusion model is validated against experimental measurements of the space-charge compensation plasma in the drift region of NIO1. Finally, the feasibility study for a beam-generated plasma neutralizer in NIO is presented. The neutralizer length, required gas target thickness, and a very simple magnetic setup were considered, taking into account the integration in NIO1. For the basic design a low ionization degree (1%) is obtained, however a promising plasma density up to hundred times the beam density was calculated. The proposed test in NIO1 can be the starting point for studying advanced schemes of magnetic confinement aiming at ionization degrees in the order of 10%.The deployment of neutral beam injectors in future fusion plants is beset by the particularly poor efficiency of the neutralization process. Beam-generated plasma neutralizers were proposed as a passive and intrinsically safe scheme of efficient plasma neutralizers. The concept is based on the natural ionization of the gas target by the beam, and on a suitable confinement of the secondary plasma. The technological challenge of such a concept is the magnetic confinement of the secondary plasma: a proof-of-principle for the concept is needed. The possibility to test of such a system in the small negative ion beam system NIO1 is discussed in this paper. The constraints given by the facility are first discussed. A model of beam-gas interaction is developed to provide the charge-state of beam particles along the neutralizer, and to provide the source terms of plasma generation. By using a cylindrical model of plasma diffusion in magnetic fields, the ionization degree of the target is estimated. In the absence ...

The ITER Neutral Beam Test Facility (NBTF), called PRIMA (Padova Research on ITER Megavolt Accelerator), is hosted in Padova, Italy and includes two experiments: MITICA, the full-scale prototype of the ITER heating neutral beam injector, and SPIDER, the full-size radio frequency negative-ions source. The NBTF realization and the exploitation of SPIDER and MITICA have been recognized as necessary to make the future operation of the ITER heating neutral beam injectors efficient and reliable, fundamental to the achievement of thermonuclear-relevant plasma parameters in ITER. This paper reports on design and R&D carried out to construct PRIMA, SPIDER and MITICA, and highlights the huge progress made in just a few years, from the signature of the agreement for the NBTF realization in 2011, up to now - when the buildings and relevant infrastructures have been completed, SPIDER is entering the integrated commissioning phase and the procurements of several MITICA components are at a well advanced stage

An axisymmetric system to recover beam energy from partially neutralized Hbeams was recently proposed, for a given beam acceleration voltage Vs . In the case of ion source NIO1 Vs may range from 20 to 60 kV. A realistic beam with 3 mrad divergence, and a composition of 25 : 50 : 25 of H- , H0 and H+ has been considered. The collector works by decelerating the Hions (into a system similar to a Faraday cup provided with an exit hole electrode), so that they are radially deflected by space charge and anode lens effects, and collected to a low kinetic energy Kc (less than 1 keV), while neutral and H+ ions can pass through the exit hole electrode. A following collector can recover H+ energy. Since the space charge calculations are challenging for highly nonlinear problem and for a possible (numerically unstable) virtual cathode phenomena different computation tools were compared for simulations. Stabilization techniques are compared. Limits for local perveance are discussed. Also mesh asymmetry effects and the related transverse oscillations of H+ beam may be observed. Efficiency over 90 % can be reached in typical conditions. The secondary yield (which is low thanks to low impact energy Kc and Faraday cup concept) is estimated.

Neutral beam injection is one of the most important methods of plasma heating in thermonuclear fusion experiments, allowing the attainment of fusion conditions as well as driving the plasma current. Neutral beams are generally produced by electrostatically accelerating ions, which are neutralised before injection into the magnetised plasma. At the particle energy required for the most advanced thermonuclear devices and particularly for ITER, neutralisation of positive ions is very inefficient so that negative ions are used. The present paper is devoted to the description of the phenomena occurring when a high-power multi-ampere negative ion beam travels from the beam source towards the plasma. Simulation of the trajectory of the beam and of its features requires various numerical codes, which must take into account all relevant phenomena. The leitmotiv is represented by the interaction of the beam with the background gas. The main outcome is the partial neutralisation of the beam particles, but ionisation of the background gas also occurs, with several physical and technological consequences. Diagnostic methods capable of investigating the beam properties and of assessing the relevance of the various phenomena will be discussed. Examples will be given regarding the measurements collected in the small flexible NIO1 source and regarding the expected results of the prototype of the neutral beam injectors for ITER. The tight connection between measurements and simulations in view of the operation of the beam is highlighted.

The ion sources play an important role in the framework of the nuclear fusion, as a fundamental part of the neutral beam injection systems needed for the auxiliary heating of the plasma magnetically confined in fusion devices. In the case of large experiments, such as ITER and beyond, the use of negative ions was found necessary to increase the neutralization efficiency of high-energy beams, calling for an additional effort in the research on the physical mechanisms regulating their formation and extraction as a beam from the source. This paper summarizes the analyses investigating the physical phenomena occurring in the source and their effect on the optics of the extracted beam. The results, carried out by means of advanced numerical tools, are particularly useful to yield a better evaluation of the real performances of the system, and particularly of the accelerator, whose modeling usually neglect some characteristics of the source. These analyses were performed for the specific case of the SPIDER experiment (Source for Production of Ion of Deuterium Extracted from an RF plasma), representing the major test bed for negative ion source worldwide. The choice of a specific device for the source modeling was found useful to support its operational phase and to help the experimental data interpretation and the identification of dangerous operating conditions. Nonetheless, the validity of the results here presented still holds in more general cases.

In the framework of the strategy for the development and the procurement of the NB systems for ITER, it has been decided to build in Padova a test facility, including two experimental devices: a full size plasma source with low voltage extraction and a full size NB injector at full beam power (1 MV). These two different devices will separately address the main scientific and technological issues of the 17 MW NB injector for ITER. In particular the full size plasma source of negative ions will address the ITER performance requirements in terms of current density and uniformity, limitation of the electron/ion ratio and stationary operation at full current with high reliability and constant performances for the whole operating time up to 1 h. The required negative ion current density to be extracted from the plasma source ranges from 290 A/m2 in D2 (D−) and 350 A/m2 in H2 (H−) and these values should be obtained at the lowest admissible neutral pressure in the plasma source volume, nominally at 0.3 Pa. The electron to ion ratio should be limited to less than 1 and the admissible ion inhomogeneity extracted from the grids should be better than 10% on the whole plasma cross-section having a surface exposed to the extraction grid of the order of 1 m2. The main design choices will be presented in the paper as well as an overview of the design of the main components and systems.

Fast neutron detectors with a sub-centimetric space resolution are required in order to qualify neutron beams in applications related to magnetically-controlled nuclear fusion plasmas and to spallation sources. Based on the results obtained with small area prototypes, the first medium-size (20 x 35.2 cm2 active area) nGEM detector has been realized for both the CNESM diagnostic system of the SPIDER NBI prototype for ITER and as a beam monitor for fast neutrons beam lines at spallation sources, too. The nGEM is a Triple GEM gaseous detector equipped with polyethylene layers used to convert fast neutrons into recoil protons through the elastic scattering process. This paper describes the performance of the medium-size nGEM detector tested at the VESUVIO beam line of the ISIS spallation source. Being this detector the actual largest area fast neutron detector based on the GEM technology, particular attention was paid in the study of detector response in different points over the active area. Measurements of GEM counting rate (both as a function of VGEM and of time) and of the capability of the detector to reconstruct the beam in different positions are presented. This detector serves as a basis for the realization of an even larger area detector that will be used in the MITICA NBI prototype for ITER that represents the evolution of SPIDER.

The ITER project requires additional heating by two neutral beam injectors, each accelerating to 1 MV a 40 A beam of negative deuterium ions, to deliver to the plasma a power of about 17 MW for one hour. As these requirements have never been experimentally met, it was recognized as necessary to setup a test facility, PRIMA (Padova Research on ITER Megavolt Accelerator), in Italy, including a full-size negative ion source, SPIDER, and a prototype of the whole ITER injector, MITICA, aiming to develop the heating injectors to be installed in ITER. This realization is made with the main contribution of the European Union, through the Joint Undertaking for ITER (F4E), the ITER Organization and Consorzio RFX which hosts the Test Facility. The Japanese and the Indian ITER Domestic Agencies (JADA and INDA) participate in the PRIMA enterprise; European laboratories, such as IPP-Garching, KIT-Karlsruhe, CCFE-Culham, CEA-Cadarache and others are also cooperating. Presently, the assembly of SPIDER is on-going and the MITICA design is being completed. The paper gives a general overview of the test facility and of the status of development of the MITICA and SPIDER main components at this important stage of the overall development; then it focuses on the latest and most critical issues, regarding both physics and technology, describing the identified solutions.

Two Neutral Beam Injectors (NBI) will provide a substantial fraction of the heating power necessary to ignite thermonuclear fusion reactions in ITER. The development of the NBI system at unprecedented parameters (40 A of negative ion current accelerated up to 1 MV) requires a strong demonstration activity, which was endorsed by ITER to optimise the crucial components and systems. A test facility, PRIMA (Padova Research on ITER Megavolt Accelerator), is presently in the final phase of construction at Consorzio RFX (Padova, Italy) in the CNR research area and will house two experiments, named SPIDER and MITICA. A full-size negative ion source, SPIDER (Source for the Production of Ions of Deuterium Extracted from Rf plasma), will be operated in the facility to demonstrate the creation and extraction of a D-/H- current up to 50/60A on a wide surface (more than 1m2) with uniformity within 10%. The second experimental device is the prototype of the whole ITER injector, MITICA (Megavolt ITer Injector and Concept Advancement), aiming to develop the knowledge and the technologies to guarantee the successful operation of the two injectors to be installed in ITER, including the capability of 1MV voltage holding at low pressure. The beam source is the key component of the system, whose design results from a tradeoff between requirements of the optics and real grids with finite thickness and thermo-mechanical constraints due to the cooling needs and the presence of permanent magnets. The experimental effort is supplemented by numerical simulations devoted to the optimisation of the accelerator optics and to the estimation of heat loads and currents on the various surfaces. In the paper the main requirements will be discussed and the design and the status of the main components and systems will be described. Particularly a review of the accelerator physics and a comparison between the designs of the SPIDER and MITICA accelerators are presented.

A joint Japan-EU R&D activity is in progress to optimize the accelerator for the ITER NBI. The accelerator baseline design is based on a five grids system which can be adapted to operate with three grids for initial operations at low voltage (500 kV). Moreover, in order to speed up the test of the NBI system at the Test Facility, a negative ion source with extraction voltage up to 100 kV will be operated in parallel to the full injector. In this contribution the three accelerators mentioned above are presented discussing the procedure to optimize the grid geometry in order to assure optimum optics during operation when the grids undergo deformations and thermal stresses due to the particles that hit their surface.

To reach fusion conditions and control plasma configuration in ITER, a suitable combination of additional heating and current drive systems is necessary. Among them, two Neutral Beam Injectors (NBI) will provide 33 MW hydrogen/deuterium particles electrostatically accelerated to 1 MeV; efficient gas-cell neutralisation at such beam energy requires negative ions, obtained by caesium-catalysed surface conversion of atoms inside the ion source. As ITER NBI requirements have never been simultaneously attained, a Neutral Beam Test Facility (NBTF) was set up at Consorzio RFX (Italy), including two experiments. MITICA is the full-scale NBI prototype with 1 MeV particle energy. SPIDER, with 100 keV particle energy, aims at testing and optimising the full-scale ion source: extracted beam uniformity, negative ion current density (for one hour) and beam optics (beam divergence