Search

This paper deals with analysis and comparison of the equivalent plastic strain and temperature fields in the aluminium alloy 2024 T3 (AA2024 T3) welded joint, with macro/microstructure appearance and hardness profile. In the alloys hardened by heat treatment, grain size and particle size of the precipitate are functions of equivalent plastic strain, strain rate and temperature. By analysing the equivalent plastic strain fields and temperature fields it is possible, to some extent, to capture the effect of welding parameters and thermo-mechanical conditions on grain structure, and therefore hardness and strength in the welded joint. A coupled thermo-mechanical model is applied to study the material behaviour during the linear welding stage of friction stir welding. The 3-D finite element model has been created in ABAQUS/EXPLICIT software using the Johnson-Cook material law. The values of thermo-mechanical quantities during the welding stage are obtained from the numerical model and shown as distributions across the joint. The obtained values of these quantities are related to the microstructure of the joint zones and hardness distribution, and this relation is discussed. [ABSTRACT FROM AUTHOR]

The influence of friction stir welding parameters on thermo-mechanical behavior of the material during welding is analyzed. An aluminum alloy is considered (Al 2024 T351), and different rotating and welding speeds are applied. The finite element model consists of the working plate (Al alloy), backing plate and welding tool. The influence of the welding conditions on material behavior is taken into account the application of the Johnson-Cook material model. The rotation speed of the tool affects the results. If increased, it contributes to an increase of friction-generated heat intensity. The other component of the generated heat, which stems from the plastic deformation of the material, is negligibly changed. When the welding speed, i.e. tool translation speed, is increased, the intensity of friction-generated heat decreases, while the heat generation due to plastic deforming is becoming more pronounced. Summed, this leads to rather small change of the total generation. The changes of the heat generation influence both the temperature field and reaction force. Also, the inadequate selection of welding parameters resulted in occurrence of the defects (pores) in the model. [ABSTRACT FROM AUTHOR]

This paper presents experimental and numerical analysis of the change of temperature and force in the vertical direction during the friction stir welding of high-strength aluminium alloy 2024 T3. This procedure confirmed the correctness of the numerical model, which is subsequently used for analysis of the temperature field in the welding zone, where it is different to determine the temperature experimentally. 3D finite element model is developed using the software package Abaqus; arbitrary Lagrangian-Eulerian formulation is applied. Johnson-Cook material law and Coulomb's Law of friction are used for modelling the material behaviour. Temperature fields are symmetrical with respect to the welding line. The temperature values below the tool shoulder, i. e. in the welding zone, which are reached during the plunge stage, are approximately constant during the entire welding process and lie within the interval 430-502 °C. The temperature of the material in the vicinity of the tool is about 500 °C, while the values on the top surface of the welding plates (outside the welding zone, but close to the tool shoulder) are about 400 °C. The temperature difference between the top and bottom surface of the plates is small, 10-15 °C. [ABSTRACT FROM AUTHOR]

This paper deals with the heat generation in the Al alloy Al2024-T3 plate under different rotating speeds and plunge speeds during the plunge stage of friction stir welding. A 3-D finite element model is developed in the commercial code ABAQUS/Explicit using the arbitrary Lagrangian-Eulerian formulation, the Johnson- Cook material law, and Coulomb's Law of friction. The heat generation in friction stir welding can be divided into two parts: frictional heat generated by the tool and heat generated by material deformation near the pin and the tool shoulder region. Numerical results obtained in this work indicate a more prominent influence from the friction-generated heat. The slip rate of the tool relative to the workpiece material is related to this portion of heat. The material velocity, on the other hand, is related to the heat generated by plastic deformation. Increasing the plunging speed of the tool decreases the friction-generated heat and increases the amount of deformation-generated heat, while increasing the tool rotating speed has the opposite influence on both heat portions. Numerical results are compared with the experimental ones, in order to validate the numerical model, and a good agreement is obtained. [ABSTRACT FROM AUTHOR]