Search

In this study, we investigate phosphomolybdic acid (PMA), which allows solution processing of quantum dot light-emitting diodes. With its low cost, easy solution processes, and excellent physical and optical properties, PMA is a potential candidate as the hole injection layer (HIL) in optoelectronic devices. We evaluate the physical and electrical properties of PMA using various solvents. The surface morphology of the PMA film was improved using a solvent with appropriate boiling points, surface tension, and viscosity to form a smooth, pinhole-free film. The energy level was regulated according to the solvent, and PMA with the appropriate electronic structure provided balanced charge carrier transport in quantum dot electroluminescent (QD-EL) devices with enhanced efficiency. A device using PMA dissolved in cyclohexanone was demonstrated to exhibit improved efficiency compared to a device using PEDOT:PSS, which is a conventional solution HIL. However, the stability of PMA was slightly poorer than PEDOT:PSS; there needs to be further investigation.

Colloidal quantum-dot-based light-emitting diodes (QD-LEDs) have gained tremendous attention as great candidates to potentially replace current emissive display technologies. The luminescence efficiency of a QD LED has increased rapidly in the past decade; this was triggered by the use of metal oxides in the charge transport layers, particularly zinc oxide (ZnO) for the electron transport layer (ETL). However, the ZnO ETL often results in undesirable device performance such as efficiency roll-off and poor device stability because of excessive electron injection into the QD emissive layer. Here, we explore solution-processable tin dioxide (SnO2) nanoparticles (NPs) as alternatives to ZnO NPs for the ETL in QD-LEDs. We evaluated the thin-film quality and electrical performance of SnO2 NPs and then applied them to the ETL for constructing QD-LEDs. As a result of the smooth surface morphology, moderate electron-transport ability, and lower carrier concentration compared to ZnO NPs, the QD-LED with SnO2 NP-ETL exhibited improved performance in terms of lower turn-on and operating voltages, maximum luminance, improved efficiency roll-off, and improved power efficiency over the reference device with the ZnO NP-ETL. This shows promising potential for SnO2 NPs in optoelectronic applications.

Self-assembled monolayers (SAMs) of organic molecules are frequently employed to improve the electrical performance of organic field-effect transistors (OFETs). However, the relationship between SAM properties and OFET performance has not been fully explored, leading to an incomplete understanding of the system. This study investigates the effect of the SAM alkyl chain length on the crystalline phase of pentacene films and OFET performance. Two types of SAMs—with alkyl chain lengths of 10 (decyltrichlorosilane, DTS) and 22 (docosyltrichlorosilane, DCTS)—were examined, and variations in the performance of pentacene-based OFETs with the nature of the SAM treatment were observed. Despite the similar surface morphologies of the pentacene films, field-effect mobility in the DCTS-treated OFET was twice that in the DTS-treated OFET. To find the reason underlying the dependence of the OFET’s electrical performance on the SAM alkyl chain length, X-ray diffraction measurements were conducted, followed by a phase analysis of the pentacene films. Bulk and thin-film phases were observed to coexist in the pentacene film grown on DTS, indicating several structural defects in the film; this can help explain the dependence of the OFET electrical performance on the SAM alkyl chain length, mediated by the different crystalline phases of pentacene.

The emerging technology of colloidal quantum dot electronics provides an opportunity for combining the advantages of well-understood inorganic semiconductors with the chemical processability of molecular systems. So far, most research on quantum dot electronic devices has focused on materials based on Pb- and Cd chalcogenides. In addition to environmental concerns associated with the presence of toxic metals, these quantum dots are not well suited for applications in CMOS circuits due to difficulties in integrating complementary n- and p-channel transistors in a common quantum dot active layer. Here, we demonstrate that by using heavy-metal-free CuInSe2 quantum dots, we can address the problem of toxicity and simultaneously achieve straightforward integration of complimentary devices to prepare functional CMOS circuits. Specifically, utilizing the same spin-coated layer of CuInSe2 quantum dots, we realize both p- and n-channel transistors and demonstrate well-behaved integrated logic circuits with low switching voltages compatible with standard CMOS electronics., Designing efficient toxic-element-free technologies in solution-processable CMOS electronics remains a challenge. Here, the authors demonstrate integrated logic CMOS circuits based on heavy-metal-free colloidal CuInSe2 quantum dots with low switching voltages and with degradation-free performance on month-long time scales.

Electrical annealing (EA) is one of the post treatments to enhance the electrical performances of organic devices. To date, the improvements using EA have only been reported for the solution-processed devices because its mechanism has been known as the alignments of ionic impurities or polymer chains. In this paper, we applied EA to thermally evaporated organic diodes which not have ionic impurities or polymer chains. After EA, the turn-on voltage of the diode was reduced, and the forward-bias current of the diode was increased without changing the reverse-bias current, resulting in an improvement of the cutoff frequency of the rectifier. In addition, we proposed a new mechanism to explain why the EA can be applied to the thermally evaporated organic devices. Based on time-of-flight secondary ion mass spectrometry and impedance spectra, we suggest that this improvement is due to the creation of a MoO3:pentacene mixed layer, leading to ease of charge injection. We believe that our finding will be helpful to understand change at the organic/metal interfaces and useful to apply a wide range of organic devices such as organic photovoltaics, organic light-emitting diodes, and organic thin-film transistors.

Large hysteresis behaviors on molybdenum disulfide (MoS2) field-effect transistors (FETs) without passivation have been typically observed, which can be one of the obstacles to understanding the intrinsic properties of MoS2 layers. Reported herein is the fact that the negligible hysteresis gap of MoS2 can be achieved through thermal annealing without any further passivation layer. The hysteresis gap of the MoS2 FETs with thermal annealing was reduced to 0.08 V, and the device showed good field-effect mobility (23.3 cm2/V s) and a high on-to-off ratio (∼107). The hysteresis-free MoS2 FETs were systematically investigated by analyzing both the contact property and the bias stability. Furthermore, low contact resistance (6.21 Ω cm) and excellent bias stability with a 1.29 × 108 sec relaxation time were obtained.

A vapor-phase-processed fluorinated silazane self-assembled monolayer (SAM), 1,3-bis(trifluoropropyl)-1,1,3,3-tetramethyldisilazane (FPDS), was introduced as a surface modifier for pentacene-based organic thin-film transistors (OTFTs). A remarkable improvement in the field effect mobility from 0.25 cm2/Vs (without SAM-treatment) to 0.42 cm2/Vs (with FPDS-treatment) was observed, which was attributed to the better pentacene growth on a hydrophobic surface. A significant reduction in the contact resistance was also observed by FPDS treatment due to the improved bulk conductivity and diminished charge trapping at the gate dielectric surface by the SAM treatment. In addition, FPDS treatment efficiently improved the bias stability of the OTFTs; the drain-to-source current degradation by the bias stress was greatly reduced from 80% to 50% by FPDS treatment, and the characteristic time for charge trapping of the FPDS treated OTFTs was approximately one order of magnitude larger than that of the OTFTs without SAM treatment.

We demonstrated modulation of charge carrier densities in all-solution-processed organic field-effect transistors (OFETs) by modifying the injection properties with self-assembled monolayers (SAMs). The all-solution-processed OFETs based on an n-type polymer with inkjet-printed Ag electrodes were fabricated as a test platform, and the injection properties were modified by the SAMs. Two types of SAMs with different dipole direction, thiophenol (TP) and pentafluorobenzene thiol (PFBT) were employed, modifying the work function of the inkjet-printed Ag (4.9 eV) to 4.66 eV and 5.24 eV with TP and PFBT treatments, respectively. The charge carrier densities were controlled by the SAM treatment in both dominant and non-dominant carrier-channel regimes. This work demonstrates that control of the charge carrier densities can be efficiently achieved by modifying the injection property with SAM treatment; thus, this approach can achieve polarity conversion of the OFETs.

Pentacene diodes with 2,3,4,5,6-pentafluorobenzenethiol-coated Au anodes show high current densities of 100 A cm−2 at 3 V with rectification ratios of 107. Using such diodes in rectifier circuits allows an output voltage of 3.8 V to be achieved from a 10 V sinusoidal input at 1 GHz.

We demonstrate that nanocrystalline Al-doped zinc oxide (n-AZO) thin film used as an electron-extraction layer can significantly enhance the performance of inverted polymer solar cells based on the bulk heterojunction of poly[[9-(1-octylnonyl)-9H-carbazole-2,7-diyl]-2,5-thiophenediyl-2,1,3-benzothiadiazole-4,7-diyl-2,5-thiophenediyl] (PCDTBT) and [6,6]-phenyl C71-butyric acid methyl ester (PC70BM). A synergistic study with both simulation and experiment on n-AZO was carried out to offer a rational guidance for the efficiency improvement. As a result, An n-AZO film with an average grain size of 13 to 22 nm was prepared by a sol-gel spin-coating method, and a minimum resistivity of 2.1 x 10(-3) Omega.cm was obtained for an Al-doping concentration of 5.83 at.%. When an n-AZO film with a 5.83 at.% Al concentration was inserted between the ITO electrode and the active layer (PCDTBT:PC70BM), the power conversion efficiency increased from 3.7 to 5.6%. (C) 2015 Optical Society of America