Search

Microencapsulation of n-tetracosane, whose melting point is approximately 50 degrees C, in a silica shell has been performed through the sol-gel method using tetraethyl orthosilicate (TEOS) as the precursor for silica-shell formation. Additionally, two types of silane coupling agents were used to modify the surface of the microcapsules to change the wettability. The morphology of the microcapsules was observed by scanning electron microscopy. The chemical composition was characterized by Fourier transform infrared spectroscopy. The results confirmed the presence of n-tetracosane and silica in the synthesized microcapsules. Wettability analysis showed hydrophobic and hydrophilic features because of the added silane coupling agents. From the results of differential scanning calorimetry measurements, the encapsulation ratio of the microcapsules increased with decreasing TEOS/n-tetracosane ratio, and the highest encapsulation ratio was 87.1 % at a TEOS/n-tetracosane ratio of 0.25. The pH in the microcapsule solution was affected by addition of a silane coupling agent, and shifting the pH to the basic side lowered the encapsulation ratio owing to enhancement of silica condensation. After 100 differential scanning calorimetry cycles, there was no significant degradation in the phase-change temperatures and enthalpies, which confirmed the good phase-change stability and repeatability. Therefore, the microcapsules are a potential material for thermal-energy-storage systems to effectively utilize energy.

Vanadium dioxide (VO2) is a phase transition material that exhibits metallic or insulating characteristics depending upon its temperature. In this study, a multilayered film consisting of 2, silicon dioxide (SiO2) and gold was proposed as a metamaterial that switches its absorptivity over a broad wavelength range depending on the ambient temperature as a fundamental element of a building pigment. At high temperatures, the multilayer showed a high absorptivity at mid-infrared wavelengths, promoting radiative cooling. Simultaneously, the multilayer presented a low absorptivity in the visible and near-infrared wavelengths, enhancing sunlight absorption. The daily average heat flux can possibly be suppressed in summer in comparison with a gray body whose emissivity was 0.8. Conversely, at a lower temperatures, the multilayer showed opposite absorptivity in both the mid-infrared and visible ranges, and its daily average heat flux increased in winter. The metal–insulator phase transition of VO2 caused a drastic shift of the resonant wavelength related to surface phonons and surface plasmons at an infrared wavelength, and optical interference at a visible wavelength, originating at the interface of the SiO2 layer. Thus, the radiative heat flux for both sunlight absorption and radiative cooling was simultaneously controlled depending on the temperature of VO2.

Droplet transportation using a wettability gradient surface has attracted much attention owing to applications such as in microfluidic devices. A surface with a spatial structural gradient was prepared through a simple and cost-effective process even though understanding of droplet behavior on the structure was still limited. Here, we report impinging droplet motion on a gradient wrinkled surface. Surfaces were prepared through hard film deposition on soft pre-strained polydimethylsiloxane (PDMS) with a mask installed with a slit to control the amount of deposition, which is related to the wavelength of the wrinkles. Droplets were impinged with varying position with respect to the structure, and the droplet motion was observed in the direction away from the region under the slit. We found an asymmetric contact angle and alternate motion on both sides of the three-phase contact line during the motion according to the gradient of the wrinkle wavelength. These results may help not only to understand the behavior of droplet impingement on a gradient structural surface but also to further develop applications using directional droplet transfer.

Securing freshwater resources is a global issue for ensuring sustainable development. Fog harvesting is attracting great attention as a method to collect water without any energy input. Previous reports that were inspired by insects and plants have given insights such as the effectiveness of in-plane wettability and structural differences for droplet transport, which might enhance artificial water harvesting efficiency. However, further efforts to transfer droplets while maintaining performance are needed because droplet motion owing to these effects is limited to the in-plane direction. In this study, we report droplet transport between three-dimensional copper wire structures with nanostructured hydrophobic and superhydrophilic features. This mechanism enhanced the fog harvesting capability by more than 20% compared with the cumulative value of individual wires. In addition, the relationship between the droplet height and spacing of wires affected the performance. Our results show the importance of out-of-plane directional droplet transport from the wire surface assisted by differences in wire wettability, which minimizes limiting factors of fog harvesting including clogging and droplet shedding. Furthermore, the proposed arrangement reduces the overall system width compared with that of a two-dimensional arrangement while maintaining the amount of harvested water. These results provide a promising approach to designing large-scale and highly efficient fog harvesters.