Search

Abstract The rise in global temperature and accumulation of petroleum-based wastes in the environment forces the scientific focus towards renewable alternatives. In the present work, an under-exploited resource – spruce bark – is investigated as a raw material for production of bio-oil as a liquid energy carrier. To enhance the energy-content of the produced bio-crude, ultimately being produced through hydrothermal liquefaction, the polysaccharides were extracted through organosolv fractionation and converted to lipids by oleaginous microorganisms. The effect originating from tannins was also investigated by performing a pre-extraction before the organosolv fractionation. It was found that performing the organosolv fractionation and upgrading the isolated organosolv lignin to bio-oil greatly reduced the oxygen content of the oil fraction thereby improving its energy content, and introducing upgraded polysaccharides in the form of lipids, as well as pre-extracted tannins, caused clear changes in the product distribution of the final bio-oil and kept a final product with low oxygen content. The other factor largely influencing the product distribution originated from the various heating rates tested by altering operational mode of the HTL process between batch and semi-continuous. Ultimately, performing the organosolv fractionation and individual upgrading of the polysaccharides had a beneficial effect on reducing the final solids content and enhancing the liquid oil yield.

Abstract Botryococcus braunii, a colonial green microalga which is well-known for its capacity to synthesize hydrocarbons, has significant promise as a long-term source of feedstock for the generation of biofuels. However, cultivating and scaling up B. braunii using conventional aqua-suspended cultivation systems remains a challenge. In this study, we optimized medium components and light intensity to enhance lipid and hydrocarbon production in a multi-cultivator airlift photobioreactor. BBM 3N medium with 200 μmol/m2/s light intensity and a 16 h light–8 h dark regimen yielded the highest biomass productivity (110.00 ± 2.88 mg/L/day), as well as the highest lipid and hydrocarbon content. Cultivation in a flat-panel bioreactor resulted in significantly higher biomass productivity (129.11 ± 2.74 mg/L/day), lipid productivity (32.21 ± 1.31 mg/L/day), and hydrocarbon productivity (28.98 ± 2.08 mg/L/day) compared to cultivation in Erlenmeyer flasks and open 20-L raceway pond. It also exhibited 20.15 ± 1.03% of protein content including elevated levels of chlorophyll a, chlorophyll b, and carotenoids. This work is noteworthy since it is the first to describe fatty acid and hydrocarbon profiles of B. braunii during cobalt treatment. The study demonstrated that high cobalt concentrations (up to 5 mg/L of cobalt nitrate) during Botryococcus culture affected hydrocarbon synthesis, resulting in high amounts of n-alkadienes and trienes as well as lipids with elevated monounsaturated fatty acids concentration. Furthermore, pyrolysis experiments on microalgal green biomass and de-oiled biomass revealed the lipid and hydrocarbon compounds generated by the thermal degradation of B. braunii that facilitate extra economical value to this system.

Abstract Background Biotransformation of waste oil into value-added nutraceuticals provides a sustainable strategy. Thraustochytrids are heterotrophic marine protists and promising producers of omega (ω) fatty acids. Although the metabolic routes for the assimilation of hydrophilic carbon substrates such as glucose are known for these microbes, the mechanisms employed for the conversion of hydrophobic substrates are not well established. Here, thraustochytrid Schizochytrium limacinum SR21 was investigated for its ability to convert oils (commercial oils with varying fatty acid composition and waste cooking oil) into ω-3 fatty acid; docosahexaenoic acid (DHA). Results Within 72 h SR21 consumed ~ 90% of the oils resulting in enhanced biomass (7.5 g L− 1) which was 2-fold higher as compared to glucose. Statistical analysis highlights C16 fatty acids as important precursors of DHA biosynthesis. Transcriptomic data indicated the upregulation of multiple lipases, predicted to possess signal peptides for secretory, membrane-anchored and cytoplasmic localization. Additionally, transcripts encoding for mitochondrial and peroxisomal β-oxidation along with acyl-carnitine transporters were abundant for oil substrates that allowed complete degradation of fatty acids to acetyl CoA. Further, low levels of oxidative biomarkers (H2O2, malondialdehyde) and antioxidants were determined for hydrophobic substrates, suggesting that SR21 efficiently mitigates the metabolic load and diverts the acetyl CoA towards energy generation and DHA accumulation. Conclusions The findings of this study contribute to uncovering the route of assimilation of oil substrates by SR21. The thraustochytrid employs an intricate crosstalk among the extracellular and intracellular molecular machinery favoring energy generation. The conversion of hydrophobic substrates to DHA can be further improved using synthetic biology tools, thereby providing a unique platform for the sustainable recycling of waste oil substrates.

Introduction: The cornerstone of preventative therapy is made up of pit and fissure sealants and fluorides. Resin sealants have been shown to help reduce fissure decay in both primary and permanent teeth. Etching of primary molars is not effective due to prismless enamel, higher organic content, and diversity in fissure shape. Methods of pretreatment of pits and fissures have been hypothesized to promote microporosities in etched enamel and hence sealant adherence. Examining the etching pattern and surface roughness of the enamel surface can be used to gauge these. Objective: This study aimed to evaluate the effect of pretreatment with ozone gas and 5.25% sodium hypochlorite solution on pits and fissures of primary teeth to check for the etching pattern and surface roughness. Materials and Methods: Thirty noncarious primary molars were sectioned to retain the crowns, and randomly divided into three groups, sodium hypochlorite, ozone gas, and control. Each sample was pretreated with the agent, washed, followed by etching with 37% phosphoric acid. Samples were sectioned and subjected to scanning electron microscope analysis to evaluate the etching pattern and surface roughness. Results: Comparison of the etching pattern in three groups showed a statistically insignificant difference (P=0.364). Surface roughness was highest in the hypochlorite group followed by ozone and control which showed a statistically significant difference (P = 0.001). The surface area between the three groups showed a statistically insignificant difference. Conclusion: Sodium hypochlorite is a better pretreatment agent compared to ozone gas and acid etching alone. However, as all results were not statistically significant further research must be carried out to prove the effectiveness of these agents.

The microalga Scenedesmus rotundus, isolated from Jabalpur, Madhya Pradesh, India was designated as Scenedesmus rotundus-MG910488 after morphological and molecular identification. In this study, the effects of various autotrophic growth media on the physiology and lipid accumulation of this microalga were investigated. The cell density, amount of photosynthetic pigments, the productivity of biomass and lipid content and the cell morphology of the microalga were shown to be significantly affected by the variation in growth media. The highest biomass of 754.56 ± 14.80 mg L−1 with biomass productivity of 37.73 ± 0.74 mg L−1 day−1 was achieved when this microalgae was cultivated in the Zarrouk’s medium, whereas the highest lipid content of 33.30 ± 1.21% was observed in the BG-11 medium. The results confirm that the BG-11 is a cost-effective and efficient growth medium for this microalga. It also shows that the ingredients of the growth medium and its concentration influence the growth and synthesis of biomolecules produced by microalga. The biodiesel produced from obtained lipids was qualitatively estimated by Gas Chromatography-Mass Spectroscopy (GC-MS), Nuclear Magnetic Resonance (1H, 13C NMR) and Fourier Transform-Infrared Spectroscopy (FT-IR), which indicate the presence of oleic acid methyl ester, linoleic acid methyl ester and palmitic acid methyl ester as the leading fatty acid methyl esters (FAME) in the samples, which make this strain an ideal feedstock for biodiesel production.

Biodiesel is an emerging alternative fuel that is generally made from edible and non-edible oilseed crops. Jatropha curcus has a high potential for producing biodiesel, which yields 25–35% oil along with 75–65% solid byproduct, generally called a de-oiled cake. The present manuscript deals with the co-digestion of Jatropha de-oiled cake along with cattle dung (1:1 ratio) for biogas production in a floating-type biogas digester. The experimental study was carried out in a modified KVIC biogas plant of 6 cubic meter capacity for 60 days’ retention time under psychrophilic and mesophilic temperature conditions. During all the experiments, the total solid content of the slurry was maintained fixed at 10–12% by mixing 10 kg Jatropha de-oiled cake and 10 kg cattle dung with 80 kg water. The experimental results showed that the average specific biogas production of Jatropha de-oiled cake and cattle dung slurry was observed to be 0.216 m3/kg TS, 0.252 m3/kg VS and 0.287 m3/kg TS, 0.335 m3/kg VS, respectively, under the aforementioned conditions. Moreover, the biogas methane concentration was observed to be 62.33% to 69.16% under mesophilic temperature conditions compared to the psychrophilic temperature conditions, 65.21% to 69.15%, respectively. Furthermore, the average total volatile solids mass removal efficiency of feeding material in the abovementioned process was 7% higher under mesophilic temperature conditions than psychrophilic temperature conditions. Additionally, the results indicated that a total 588.8 kg of input volatile solids produced a total of 7306.56 MJ/m3 and 5177.88 MJ/m3 energy in 60 days under psychrophilic and mesophilic temperature conditions. On the basis of the results, it is concluded that Jatropha de-oiled cake may be a superior solution for improving biogas quality and composition as well as a value-added product, i.e., organic manure.

Photosynthetic organisms such as eukaryotic microalgae and prokaryotic cyanobacteria synthesize a wide range of valuable chemicals. They are predicted to become efficient and renewable sources for valuable products in the future due to their high biomass synthesis using CO2 and solar energy. Microalgae are producers of several carotenoids including lutein, which is a xanthophyll carotenoid with several health advantages, including the prevention of age-related macular degeneration. Currently, it is extracted on commercial scale from marigold flower petals, however, production from plant sources is highly affected by seasonal variations, requires arable land, and has high production cost. Microalgae, on the other hand, are an ideal alternative for lutein synthesis due to their rapid growth and high biomass and lutein yield. It is, however, necessary to further improve lutein productivity, for a successful transition to commercial production. This article describes lutein biosynthesis in microalgae by using their native biochemical pathways, as well as possible target genes for genetic engineering to enhance lutein production. Understanding the processes behind lipid droplet synthesis in chloroplasts, as well as carotenoid transport across chloroplast membranes and carotenoid esterification, might lead to novel ways to boost lutein levels in microalgae.

Municipal mixed plastic waste (MMPW) recycling is an innovative way to turn environmental waste into energy fuels. In the present study, a thermochemical process was applied to depolymerize MMPW to produce hydrocarbon fuels known as plasto-oil. The obtained plasto-oil was blended with conventional diesel to test the performance of the PCCI-mode single-cylinder, four-stroke, direct-injection diesel engine. The PCCI combustion mixture was tested with 15% and 30% fuel vapor to ensure homogeneity with and without exhaust gas recirculation. The modified engine findings were compared to a standard conventional engine. At higher loads, PCCI combustion showed reduced emission of carbon monoxide and nitrogen oxides. While the thermal braking efficiency was marginally reduced at all engine loads while using the blends. The results showed that with and without 10% exhaust gas recirculation, an increase in air mix reduced NOx emissions; however, in the case of smoke emissions, an opposite trend was observed. A blend of plasto-oils also decreased CO and unburned hydrocarbon (HC) emissions at higher loads. In conclusion, it was shown that plasto-oils combined with conventional diesel fuel outperformed diesel fuel alone.

Yeasts are widely used in various sectors of biotechnology, from white (industrial) to red (medical) [...]

Abstract Background Recent evidence points to the nutritional importance of docosahexaenoic acid (DHA) in the human diet. Thraustochytrids are heterotrophic marine oleaginous microorganisms capable of synthesizing high amounts of DHA, as well as other nutraceutical compounds such as squalene, in their cellular compartment. Squalene is a natural triterpene and an important biosynthetic precursor to all human steroids. It has a wide range of applications in the cosmetic and pharmaceutical industries, with benefits that include boosting immunity and antioxidant activity. Apart from its nutritional quality, it can also be utilized for high-grade bio-jet fuel by catalytic conversion. Results In the present study, the potential of thraustochytrid strain Aurantiochytrium sp. T66 to produce DHA and squalene was evaluated. When the strain was cultivated on organosolv-pretreated birch hydrolysate (30 g/L glucose) in flask, it resulted in 10.39 g/L of cell dry weight and 4.98 g/L of total lipids, of which 25.98% was DHA. In contrast, when the strain was grown in a bioreactor, cell dry weight, total lipid, and DHA increased to 11.24 g/L, 5.90 g/L, and 35.76%, respectively. The maximum squalene yield was 69.31 mg/gCDW (0.72 g/L) when the strain was cultivated in flask, but it increased to 88.47 mg/gCDW (1.0 g/L), when cultivation shifted to a bioreactor. Conclusions This is the first report demonstrating the utilization of low cost non-edible lignocellulosic feedstock to cultivate the marine oleaginous microorganism Aurantiochytrium sp. for the production of nutraceutical vital compounds. Owing to the simultaneous generation of DHA and squalene, the strain is suitable for industrial-scale production of nutraceuticals.

Environmental pollution, greenhouse gas emissions, depletion of fossil fuels, and a growing population have sparked a search for new and renewable energy sources such as biodiesel. The use of waste or residues as substrates for microbial growth can favor the implementation of a biorefinery concept with reduced environmental footprint. Cyanobacteria constitute microorganisms with enhanced ability to use industrial effluents, wastewaters, forest residues for growth, and concomitant production of added-value compounds. In this study, a recently isolated cyanobacterium strain of Pseudanabaena sp. was cultivated on hydrolysates from pretreated forest biomass (silver birch and Norway spruce), and the production of biodiesel-grade lipids was assessed. Optimizing carbon source concentration and the (C/N) carbon-to-nitrogen ratio resulted in 66.45% w/w lipid content when microalgae were grown on glucose, compared to 62.95% and 63.79% w/w when grown on spruce and birch hydrolysate, respectively. Importantly, the lipid profile was suitable for the production of high-quality biodiesel. The present study demonstrates how this new cyanobacterial strain could be used as a biofactory, converting residual resources into green biofuel.

The world increasingly requires biodegradable and renewable products in all production fields, with the vast volume of emissions generated by the fuel sector presenting a difficult issue that needs to be addressed [...]

Oleaginous yeasts have attracted increasing scientific interest as single cell oil (SCO) producers. SCO can be used as a fossil-free fuel substitute, but also as a source of rarely found odd-chain fatty acids (OCFAs), such as C15, C17, and C25 fatty acids which have a wide range of nutritional and biological applications. Volatile fatty acids (VFAs) have gained interest as sustainable carbon source for yeasts. This study aims to improve current knowledge on yeast species that yield high amounts of SCO using VFAs as a carbon source. Specifically, the growth of the promising yeasts Cryptococcus curvatus and Rhodotorula toruloides was evaluated on individual VFAs, such as acetic, propionic, and butyric acid. C. curvatus proved to be more tolerant in higher concentrations of VFAs (up to 60 g/L), while butyric acid favored biomass and lipid conversion (0.65 and 0.23 g/gsubstrate, respectively). For R. toruloides, butyric acid favored biomass conversion (0.48 g/gsubstrate), but lipid conversion was favored using acetic acid, instead (0.14 g/gsubstrate). Propionic acid induced the formation of OCFAs, which yielded higher amounts for C. curvatus (up to 2.17 g/L). VFAs derived from the anaerobic digestion of brewer’s spent grain were tested as a cost-competitive carbon source and illustrated the significance of the combination of different VFAs in the quality of the produced SCO, by improving the biodiesel properties and OCFAs production.

Rapid climate change and forecasted damage from fossil fuel combustion, forced researchers to investigate renewable and clean energy sources for the sustainable development of societies throughout the world. Biomass-based energy is one of the most important renewable energy sources for meeting daily energy needs, which are gaining in popularity daily. Gasification-based bioenergy production is an effective way to replace fossil fuels and reduce CO2 emissions. Even though biomass gasification has been studied extensively, there is still much opportunity for improvement in terms of high-quality syngas generation (high H2/CO ratio) and reduced tar formation. Furthermore, the presence of tar has a considerable impact on syngas quality. Downdraft gasifiers have recently shown a significant potential for producing high-quality syngas with lower tar concentrations. This article presents a comprehensive review on the advancement in biomass downdraft gasification technologies for high-quality synthesis gas. In addition, factors affecting syngas production and composition e.g., equivalency ratio, temperature, particle size, and gasification medium on synthesis gas generation are also comprehensively studied. The up-gradation and various applications of synthesis gas are also discussed in brief in this review article.

Given an increasing focus on environmental sustainability, microbial oils have been suggested as an alternative to petroleum-based products. However, microbial oil production relies on the use of costly sugar-based feedstocks. Substrate limitation, elevated costs, and risk of contamination have sparked the search for alternatives to sugar-based platforms. Volatile fatty acids are generated during anaerobic digestion of organic waste and are considered a promising substrate for microbial oil production. In the present study, two freshwater and one marine microalga along with two thraustochytrids were evaluated for their potential to produce lipids when cultivated on volatile fatty acids generated from food waste via anaerobic digestion using a membrane bioreactor. Freshwater microalgae Auxenochlorella protothecoides and Chlorella sorokiniana synthesized lipids rich in palmitic acid (C16:0), stearic acid (C18:0), oleic acid (C18:1), and linoleic acid (C18:2). This composition corresponds to that of soybean and jatropha oils, which are used as biodiesel feedstock. Production of added-value polyunsaturated fatty acids (PUFA) mainly omega-3 fatty acids was examined in three different marine strains: Aurantiochytrium sp. T66, Schizochytrium limacinum SR21, and Crypthecodinium cohnii. Only Aurantiochytrium sp. T66 seemed promising, generating 43.19% docosahexaenoic acid (DHA) and 13.56% docosapentaenoic acid (DPA) in total lipids. In summary, we show that A. protothecoides, C. sorokiniana, and Aurantiochytrium sp. T66 can be used for microbial oil production from food waste material.

The marine microorganisms thraustochytrids have been explored for their potential in the production of various bioactive compounds, such as DHA, carotenoids, and squalene. Squalene is a secondary metabolite of the triterpenoid class and is known for its importance in various industrial applications. The bioinformatic analysis for squalene synthase (SQS) gene (the first key enzyme in the tri-terpenoid synthesis pathway), that is prevailing among thraustochytrids, is poorly investigated. In-silico studies combining sequence alignments and bioinformatic tools helped in the preliminary characterization of squalene synthases found in Aurantiochytrium limacinum. The sequence contained highly conserved regions for SQS found among different species indicated the enzyme had all the regions for its functionality. The signal peptide sequence and transmembrane regions were absent, indicating an important aspect of the subcellular localization. Secondary and 3-D models generated using appropriate templates demonstrated the similarities with SQS of the other species. The 3-D model also provided important insights into possible active, binding, phosphorylation, and glycosylation sites.

Abstract Background The aim of this work was to establish a process for the heterotrophic growth of green microalgae using forest biomass hydrolysates. To provide a carbon source for the growth of the green microalgae, two forest biomasses (Norway spruce and silver birch) were pretreated with a hybrid organosolv-steam explosion method, resulting in inhibitor-free pretreated solids with a high cellulose content of 77.9% w/w (birch) and 72% w/w (spruce). Pretreated solids were hydrolyzed using commercial cellulolytic enzymes to produce hydrolysate for the culture of algae. Results The heterotrophic growth of A. protothecoides was assessed using synthetic medium with glucose as carbon source, where the effect of sugar concentration and the carbon-to-nitrogen ratio were optimized, resulting in accumulation of lipids at 5.42 ± 0.32 g/L (64.52 ± 0.53% lipid content) after 5 days of culture on glucose at 20 g/L. The use of birch and spruce hydrolysates was favorable for the growth and lipid accumulation of the algae, resulting in lipid production of 5.65 ± 0.21 g/L (66 ± 0.33% lipid content) and 5.28 ± 0.17 g/L (63.08 ± 0.71% lipid content) when grown on birch and spruce, respectively, after only 120 h of cultivation. Conclusions To the best of our knowledge, this is the first report of using organosolv pretreated wood biomass hydrolysates for the growth and lipid production of microalgae in the literature. The pretreatment process used in this study provided high saccharification of biomass without the presence of inhibitors. Moreover, the lipid profile of this microalga showed similar contents to vegetable oils which improve the biodiesel properties.

Biolubricants refer to eco-friendly, biodegradable, and non-toxic lubricants. Their applications are still limited compared to mineral oils; however, their sustainable credentials are making them increasingly attractive. Vegetable oils are frequently used for this purpose. However, vegetable oils have issues of low lipid productivity, dependence on climatic conditions, and need for agricultural land. Microbial oils represent a more sustainable alternative. To ensure their widespread applicability, the suitability of microbial oils from a physicochemical point of view needs to be determined first. In this study, oils obtained from various oleagenic microbes—such as microalgae, thraustochytrids, and yeasts—were characterized in terms of their fatty acid profile, viscosity, friction coefficient, wear, and thermal stability. Oleaginous microalgal strains (Auxenochlorella protothecoides and Chlorella sorokiniana), thraustochytrids strains (Aurantiochytrium limacinum SR21 and Aurantiochytrium sp. T66), and yeast strains (Rhodosporidium toruloides and Cryptococcus curvatus) synthesized 64.5%, 35.15%, 47.89%, 47.93%, 56.42%, and 52.66% of lipid content, respectively. Oils from oleaginous microalgae (A. protothecoides and C. sorokiniana) and yeasts (R. toruloides and C. curvatus) possess excellent physicochemical and tribological qualities due to high amount of monounsaturated fatty acids (oleic acid C18:1 content, 56.38%, 58.82%, 46.67%, 38.81%) than those from oleaginous thraustochytrids (A. limacinum SR21 and Aurantiochytrium sp. T66; 0.96%, 0.08%, respectively) supporting their use as renewable and biodegradable alternatives to traditional mineral oil-based lubricants. Oil obtained from microalgae showed a lower friction coefficient than oils obtained from yeasts and thraustochytrids.

Thraustochytrids are considered natural producers of omega-3 fatty acids as they can synthesize up to 70% docosahexaenoic acids (DHA) of total lipids. However, commercial and sustainable production of microbial DHA is limited by elevated cost of carbon substrates for thraustochytrids cultivation. This problem can be addressed by utilizing low-cost renewable substrates. In the present study, growth, lipid accumulation and fatty acid profiles of the marine thraustochytrid Aurantiochytrium sp. T66 (ATCC-PRA-276) cultivated on volatile fatty acids (C1, formic acid; C2, acetic acid; C3, propionic acid; C4, butyric acid; C5, valeric acid and C6, caproic acid) and glucose as control were evaluated for the first time. This strain showed an inability to utilize C3, C5 and C6 as a substrate when provided at >2 g/L, while efficiently utilizing C2 and C4 up to 40 g/L. The highest cell dry weight (12.35 g/L) and total lipid concentration (6.59 g/L) were attained when this strain was cultivated on 40 g/L of butyric acid, followed by cultivation on glucose (11.87 g/L and 5.34 g/L, respectively) and acetic acid (8.70 g/L and 3.43 g/L, respectively). With 40 g/L butyric acid, the maximum docosahexaenoic acid content was 2.81 g/L, corresponding to 42.63% w/w of total lipids and a yield of 0.23 g/gcell dry weight (CDW). This marine oleaginous microorganism showed an elevated potential for polyunsaturated fatty acids production at higher acetic and butyric acid concentrations than previously reported. Moreover, fluorescence microscopy revealed that growth on butyric acid caused cell size to increase to 45 µm, one of the largest values reported for oleaginous microorganisms, as well as the presence of numerous tiny lipid droplets.

Microorganisms are known to be natural oil producers in their cellular compartments. Microorganisms that accumulate more than 20% w/w of lipids on a cell dry weight basis are considered as oleaginous microorganisms. These are capable of synthesizing vast majority of fatty acids from short hydrocarbonated chain (C6) to long hydrocarbonated chain (C36), which may be saturated (SFA), monounsaturated (MUFA), or polyunsaturated fatty acids (PUFA), depending on the presence and number of double bonds in hydrocarbonated chains. Depending on the fatty acid profile, the oils obtained from oleaginous microorganisms are utilized as feedstock for either biodiesel production or as nutraceuticals. Mainly microalgae, bacteria, and yeasts are involved in the production of biodiesel, whereas thraustochytrids, fungi, and some of the microalgae are well known to be producers of very long-chain PUFA (omega-3 fatty acids). In this review article, the type of oleaginous microorganisms and their expertise in the field of biodiesel or omega-3 fatty acids, advances in metabolic engineering tools for enhanced lipid accumulation, upstream and downstream processing of lipids, including purification of biodiesel and concentration of omega-3 fatty acids are reviewed.

Seriola lalandi has been recognized as a potential aquaculture species in Chile, however, little is known about the genetic structure of local populations. This is important, as the current production system is based on an initial wild catching and ill management of these stocks can cause reduced genetic variability. To assess the genetic structure of local S. lalandi we evaluated 27 published microsatellite markers developed from genomic libraries of other species of the genera. However only 12 markers could be used to properly assess the populations, most of these markers showed deviations from Hardy-Weinberg equilibrium with moderate inbreeding (F = 0.12). This species tends to show schooling behavior, so in all likelihood mating between relatives within small groups of fish is not unexpected. The population structure was assessed using Structure software, showing the presence of admixture with varying levels of individual ancestry. This was seen in both populations, without significant genetic differentiation. This may be explained by the migratory behavior, with mating between different populations likely to happen in small groups. Management of aquaculture resources is essential to secure a sustainable production system; this study is the first to provide estimates of genetic diversity of Chilean populations of S. lalandi.

Amelogenesis imperfecta (AI) is a group of hereditary disorders that affect the quality and/or quantity of dental enamel. This paper describes the clinicopathological features of a patient who was born of nonconsanguineous parents and who presented with oral alterations, including yellow and misshapen teeth, intrapulpal calcifications, delayed tooth eruption, and gum enlargement. Scanning electron microscopy of the teeth revealed hypoplastic enamel, and a renal ultrasound detected bilateral nephrocalcinosis, leading to a diagnosis of AI and nephrocalcinosis syndrome. Since nephrocalcinosis is often asymptomatic and can be associated with impaired renal function, dentists who see children with a generalized and thin hypoplastic AI should consider a renal ultrasound scan and referral to a Nephrologist. Children with nephrocalcinosis should also be considered for a dental check.

The rising demand and cost of fossil fuels (diesel and gasoline), together with the need for sustainable, alternative, and renewable energy sources have increased the interest for biomass-based fuels such as biodiesel. Among renewable sources of biofuels, biodiesel is particularly attractive as it can be used in conventional diesel engines without any modification. Oleaginous yeasts are excellent oil producers that can grow easily on various types of hydrophilic and hydrophobic waste streams that are used as feedstock for single cell oils and subsequently biodiesel production. In this study, cultivation of Rhodosporidium kratochvilovae on a hydrophobic waste (clarified butter sediment waste medium (CBM)) resulted in considerably high lipid accumulation (70.74% w/w). Maximum cell dry weight and total lipid production were 15.52 g/L and 10.98 g/L, respectively, following cultivation in CBM for 144 h. Neutral lipids were found to accumulate in the lipid bodies of cells, as visualized by BODIPY staining and fluorescence microscopy. Cells grown in CBM showed large and dispersed lipid droplets in the intracellular compartment. The fatty acid profile of biodiesel obtained after transesterification was analyzed by gas chromatography-mass spectrometry (GC−MS), while its quality was determined to comply with ASTM 6751 and EN 14214 international standards. Hence, clarified sediment waste can be exploited as a cost-effective renewable feedstock for biodiesel production.

Polyunsaturated fatty acids (PUFAs) are essential for human function, however they have to be provided through the diet. As their production from fish oil is environmentally unsustainable, there is demand for new sources of PUFAs. The aim of the present work was to establish the microalgal platform to produce nutraceutical-value PUFAs from forest biomass. To this end, the growth of Phaeodactylum tricornutum on birch and spruce hydrolysates was compared to autotrophic cultivation and glucose synthetic media. Total lipid generated by P. tricornutum grown mixotrophically on glucose, birch, and spruce hydrolysates was 1.21, 1.26, and 1.29 g/L, respectively. The highest eicosapentaenoic acid (EPA) production (256 mg/L) and productivity (19.69 mg/L/d) were observed on spruce hydrolysates. These values were considerably higher than those obtained from the cultivation without glucose (79.80 mg/L and 6.14 mg/L/d, respectively) and also from the photoautotrophic cultivation (26.86 mg/L and 2.44 mg/L/d, respectively). To the best of our knowledge, this is the first report describing the use of forest biomass as raw material for EPA and docosapentaenoic acid (DHA) production.

Brewers’ spent grain (BSG) accounts for 85% of the total amount of by-products generated by the brewing industries. BSG is a lignocellulosic biomass that is rich in proteins, lipids, minerals, and vitamins. In the present study, BSG was subjected to pretreatment by two different methods (microwave assisted alkaline pretreatment and organosolv) and was evaluated for the liberation of glucose and xylose during enzymatic saccharification trials. The highest amount of glucose (46.45 ± 1.43 g/L) and xylose (25.15 ± 1.36 g/L) were observed after enzymatic saccharification of the organosolv pretreated BSG. The glucose and xylose yield for the microwave assisted alkaline pretreated BSG were 34.86 ± 1.27 g/L and 16.54 ± 2.1 g/L, respectively. The hydrolysates from the organosolv pretreated BSG were used as substrate for the cultivation of the oleaginous yeast Rhodosporidium toruloides, aiming to produce microbial lipids. The yeast synthesized as high as 18.44 ± 0.96 g/L of cell dry weight and 10.41 ± 0.34 g/L lipids (lipid content of 56.45 ± 0.76%) when cultivated on BSG hydrolysate with a C/N ratio of 500. The cell dry weight, total lipid concentration and lipid content were higher compared to the results obtained when grown on synthetic media containing glucose, xylose or mixture of glucose and xylose. To the best of our knowledge, this is the first report using hydrolysates of organosolv pretreated BSG for the growth and lipid production of oleaginous yeast in literature. The lipid profile of this oleaginous yeast showed similar fatty acid contents to vegetable oils, which can result in good biodiesel properties of the produced biodiesel.

Microbial oils, obtained from oleaginous microorganisms are an emerging source of commercially valuable chemicals ranging from pharmaceuticals to the petroleum industry. In petroleum biorefineries, the microbial biomass has become a sustainable source of renewable biofuels. Biodiesel is mainly produced from oils obtained from oleaginous microorganisms involving various upstream and downstream processes, such as cultivation, harvesting, lipid extraction, and transesterification. Among them, lipid extraction is a crucial step for the process and it represents an important bottleneck for the commercial scale production of biodiesel. Lipids are synthesized in the cellular compartment of oleaginous microorganisms in the form of lipid droplets, so it is necessary to disrupt the cells prior to lipid extraction in order to improve the extraction yields. Various mechanical, chemical and physicochemical pretreatment methods are employed to disintegrate the cellular membrane of oleaginous microorganisms. The objective of the present review article is to evaluate the various pretreatment methods for efficient lipid extraction from the oleaginous cellular biomass available to date, as well as to discuss their advantages and disadvantages, including their effect on the lipid yield. The discussed mechanical pretreatment methods are oil expeller, bead milling, ultrasonication, microwave, high-speed and high-pressure homogenizer, laser, autoclaving, pulsed electric field, and non-mechanical methods, such as enzymatic treatment, including various emerging cell disruption techniques.