Search

• A new method of defining the velocity field in the coolant inlet is used to quantitatively investigate the effects of the coolant swirl intensity on the film cooling performance in the operating conditions of h series turbine vanes. • The critical value of the coolant vorticity to the transformation of film coverage is 20,000 /s. • When the coolant vorticity is 40,000 /s, the area-averaged film cooling effectiveness at the near field downstream of the film hole is 54 % higher than the non-swirling case. • With high blowing ratios and large vorticities, a stable flow field is formed, where the additional coolant vortex and induced vortex appear. • For high blowing ratios, with the increase of the vorticity, the momentum advantage of the coolant gradually transforms into the effectiveness advantage. Advanced H/J series heavy-duty gas turbines are widely equipped with film cooling to protect turbine blades. Previous studies have shown that coolant swirl has an important influence on film cooling performance. However, there are few studies on the quantitative analysis of the coolant swirl intensity because of the swirl generated by the specific structure, and most of the research was carried out at relatively low temperatures. In this paper, a new method of defining the velocity field in the coolant inlet is used to quantitatively investigate the coolant swirl intensity. A numerical study of the film cooling performance for the coolant jet with various swirl intensities is conducted in the operating conditions of H series turbine vanes. The effects of the blowing ratio and coolant vorticity on the vortex structure and mixing process of the flow field are investigated emphatically, and the mechanisms for the variation of the film cooling effectiveness are analyzed. The results show that the film cooling effectiveness is greatly improved with the swirling coolant jet at high blowing ratios. When Ω n =40,000 /s, the area-averaged (L = 5 D) film cooling effectiveness is 54 % higher than the non-swirling case. Ω n =20,000 /s is a critical value of the coolant vorticity. When Ω n >20,000 /s, the film coverage transforms significantly. Furthermore, the main vortical structures in a typical SJICF flow field with high blowing ratios and large vorticities are proposed. Compared with the non-swirling JICF, the additional coolant vortex and induced vortex appear in the SJICF. Under the influence of the two vortices, the coolant momentum is sacrificed for enhanced attachment to the wall resulting in the momentum advantage gradually transforming into the effectiveness advantage with the increase of the vorticity. [ABSTRACT FROM AUTHOR]

The gas turbine blade tip might face substantial heat loads because of leakage flow between the blades and the casing. For blade tip cooling, a composite cooling structure with film holes and broken ribs is first used on GE-E3 blade in this work. The flow and cooling characteristics of the innovative structure are studied by numerical simulation under various blowing ratio (BR) conditions. Meanwhile, the impact of modifying both the rib angle and the rib height on the adiabatic film cooling effectiveness (AFCE) at the tip of the squealer is analyzed. According to the results, adding rib structures to the squealer tip can effectively regulate the paths of cavity vortices and kidney-shaped vortex pairs (KVP) at the tip. As a result, the averaged AFCE at the blade tip is improved. The notch pressure-side broken rib structure has good aerothermal performance, and the highest AFCE at BRs of 0.50, 1.00, and 1.50 basically occur under the "R60-100 %" condition (R60 refers to the rib structure of 60°, and 100 % is the ratio of rib height to notch depth), and the corresponding AFCE are 27.71 %, 26.00 %, and 32.47 % higher than those of the no-rib case, respectively. The corresponding AFCE increased by 27.71 %, 26.52 %, and 32.47 %, respectively, compared to the no-rib condition. The highest AFCE at a BR of 1.50 occurs at "R75-70 %", which is a 38.20 % increase in AFCE compared to the no rib case. The improvement in AFCE is due to the difference in the flow of the cooling jets, which are subject to cavity vortices at different BRs. The analysis shows that the addition of ribs disrupts the formation of KVPs and weakens the influence of the cavity vortex, thus reducing the low AFCE region at the lower end of the tip groove and increasing the AFCE. However, due to the blocking effect of the ribs, the pressure loss at the blade tip is elevated. The proposed blade tip cooling structure is expected to provide new ideas for the next generation of advanced gas turbine cooling designs. • A composite tip cooling structure with film holes and broken ribs is proposed. • The flow and cooling characteristics under various blowing ratio conditions are studied. • Impact of modifying rib structure dimensions on effectiveness at squealer tip is analyzed. • Squealer tip ribs can regulate cavity vortices and kidney-shaped vortex pairs, thus improving cooling effectiveness. • The proposed tip cooling structure provides new ideas for next generation blade cooling designs. [ABSTRACT FROM AUTHOR]

• A novel double-wall with composite swirl/film cooling structure was proposed. • The structure exhibited outstanding overall cooling effectiveness (OCE) in the simulated range. • The cooling performance at high blowing ratios were obtained and the OCE was sensitive to bi. • The empirical correlations obtained by nonlinear fitting were in good agreement with the simulations. • It provided a guidance for developing advanced gas turbine blades double-wall cooling structures. A novel double-wall with composite swirl/film cooling structure is proposed in this work to enhance the cooling effectiveness of contemporary gas turbine blades. The influence of different shaped chambers and Biot numbers on the overall cooling effectiveness (OCE) are investigated by Reynolds time-averaged Navier-Stokes simulations and conjugate heat transfer analysis. The results suggest that the proposed composite cooling configuration exhibits outstanding OCE in the simulated range. When the R m is 1.00 and the Biot number is 0.11, the OCE of the composite structure is improved by 8.92 % over the conventional double-wall structure, and the distribution is more uniform. In addition, the optimal flow and cooling performance of the composite swirl/film cooling structure at high R m conditions are obtained. The OCE is very sensitive to the variation of the Biot number. Finally, the empirical correlations obtained by the multivariate nonlinear regression fitting method are in good agreement with the simulations, with errors within 10 %. The results also provide important guidance for the development of advanced gas turbine blades double-wall cooling structures. [ABSTRACT FROM AUTHOR]