Search

This paper investigates the characterization of in-plane shear properties of thermoplastic composites reinforced with Kevlar/basalt fabrics. Different fabrics had architectures of two dimensional plain woven (2D-P) and three dimensional angle-interlock (3D-A). Intralayer hybridization was performed during the weaving of the fabrics with the combination of Kevlar and basalt yarns. Five 2D-P and three 3D-A composite laminates were manufactured with polypropylene (PP) as a matrix, using compression molding. Iosipescu shear tests were carried out to evaluate the in-plane shear properties. The experimental results revealed that the shear properties including shear modulus, shear strength and shear failure strain of homogeneous composites were improved by 6.5–14.9%, 4.3–19.7%, and 3.2–46.7%, respectively. Similarly, change in the fabric architecture from 2D-P to 3D-A also enhanced the shear strength and shear failure strain by 32.0–41.6% and 7.2–22.5%, respectively. Intralayer hybrid composites had better in-plane shear properties than the interlayer hybrid composites. The fracture morphologies of the specimens were examined by scanning electron microscopy (SEM). [ABSTRACT FROM AUTHOR]

In this study, low velocity impact (LVI) behaviors of composite laminates reinforced with fabrics of different architecture are investigated. Three kinds of fabric architecture, namely, two-dimensional plain woven (2D-P), three-dimensional orthogonal (3D-O) and three-dimensional angle interlock (3D-A), are prepared with Kevlar 29 (Kevlar) yarns. Composite laminates are manufactured with Kevlar fabrics and polypropylene (PP) resin. These composites are impact tested at 4 m/s and 6 m/s impact velocities. The post-impact response of the composites of different fabric architecture is studied. The results revealed that the impact resistance is mainly dependent on the in-plane stiffness of the laminates. The energy absorption ability is predominantly influenced by the existence of yarns in the thickness direction. The 3D composites absorbed 14–26% higher energy than the 2D laminates. Especially, 3D-A laminates exhibited a higher peak load (14.21–30.25%), more energy absorption (12.7–26.2%) and lower cone formation at the back of the target (25–39%) as compared to 3D-O and 2D-P composites. [ABSTRACT FROM AUTHOR]

In this study, experimental investigations on Kevlar fiber reinforced polypropylene (PP) woven composites under high strain rate compression loading are discussed. Kevlar/PP composite laminates with 8 and 24 layers are fabricated using vacuum assisted compression molding technique. Maleic anhydride grafted-PP (MAg-PP) is added to PP to improve the interfacial property between Kevlar fiber and PP resin. The through-thickness properties at high strain rates from 1370 to 6066 s −1 are obtained using split Hopkinson pressure bar (SHPB) setup. The behavior of PP resin is found to be different than the commonly used thermoset resins, such as epoxy. Dynamic stress–strain relations are drawn to reveal the mechanical properties at high strain rates and these relations appear to be rate sensitive. As a result, the peak stress increased by three times, toughness increased by almost ten times and strain at peak stress increased by as much as two times with an increase in the strain rate. The final failure of the specimens is examined by scanning electron microscopy (SEM) to explore the possible failure mechanisms such as, delamination, fiber failure and shear fracture. [ABSTRACT FROM AUTHOR]

The present study deals with the quasi-static and high strain rate characterization of Kevlar-129 based thermoplastic composites. Two different thermoplastic matrices, namely, Polypropylene (PP) and Polyetherimide (PEI) were used to manufacture composite laminates. Quasi-static compression tests were performed at strain rates of 0.041 s−1 and 0.045 s−1. High strain rate tests were performed using a split Hopkinson pressure bar apparatus within the strain rates ranging from 2548 s−1 to 4379 s−1. Stress-strain relations reveals the rate-sensitive behaviour of composites. Kevlar/PP (K-PP) showed higher peak stress under quasi-static loading as compared to the high strain rate test. Comparable peak stresses were revealed under quasi-static and high strain rate loading for Kevlar/PEI (K-PEI) composite. Also, high strain rate compression properties such as peak stress, peak strain and toughness of K-PP were 25%, 27% and 6% higher than that of the K-PEI composite. The failure mechanisms of both the composites were characterized through macroscopic and scanning electron microscopy. K-PP failed majorly due to matrix crush and fibre failure while K-PEI failed due to shear cracking. Damage study reveals that a single fibre based composite system can be tailored to act as an energy-absorbing or dissipating material system by varying the thermoplastic matrix materials. • Static and dynamic compressive properties of Kevlar reinforced high-performance polymers. • Kevlar/Polypropylene outperforms over Kevlar/Polyetherimide under both the quasi-static and high strain rate loads. • The quasi-static strength of Kevlar/Polypropylene is 25% higher than its high strain rate strength. • Polypropylene matrix results in ductile failure, while the Polyetherimide matrix results in brittle failure. [ABSTRACT FROM AUTHOR]