Search

Shear thickening fluids (STFs) are a special class of field responsive fluids which exhibit change of phase from liquid to solid when subjected to imposed shear. This remarkable characteristic of STFs has led to their application in soft body armor technologies, leading the development of concept of Liquid Body Armors (LBAs). LBAs extensively rely upon the symbiotic relationship between STF and high strength FRP (Fiber Reinforced Polymer) composites comprising of high tenacity fibers such as Kevlar, UHMWPE (Ultra High Molecular Weight Poly Ethylene) etc. Although in the past, STFs have been widely characterized by rheometers at low strain rates (≤10 3 s −1 ), but in actual practical scenarios, body armours encounter much higher strain rates (of the order of 10 5 –10 7 s −1 ) under a ballistic impact. The main objective of this study is to capture the dynamics of STFs at such high strain rates by employing Split Hopkinson Pressure Bar (SHPB) technique. The STF sample was synthesized by dispersing 67.5 wt.% of 100 nm silica powder in Poly Propylene Glycol (PPG) and ethanol, using ultrasonic homogenization method. The mechanical response of STF was studied at high strain rates in terms of the stress-strain behavior and variation of the impact toughness with the loading rate of the fluid specimen. It was observed that the impact toughness of STF increased progressively with the specimen loading rate. The peak stress and peak strain rate attained in the SHPB tests were 147 MPa and 22,100 s −1 , respectively. The characteristic transition time of STF was found to be in the range of 13–25 µs. [ABSTRACT FROM AUTHOR]

Kevlar ® fabric reinforced plastics (KFRPs) are specialized composites with multiple layers of fabrics (∼ranging from 20 to 50 layers) designed for high impact applications. In this work, Kevlar-129 fiber was reinforced with polyetherimide (PEI) and polypropylene (PP) to obtain two groups of laminates in three configurations i.e. 16, 24 and 30 layers. Holes of diameter 11.6 mm were profile cut using fiber laser machining system operating at 1070 nm wavelength. Effects of polymeric matrix on the failure of the Kevlar – polyetherimide (K-PEI) and Kevlar – polypropylene (K-PP) laminates were characterized by studying the following: (i) threshold laser power required to make the holes (ii) surface morphology using scanning electron microscopy (iii) damage zone along the laser cut path using scanning acoustic microscopy and optical microscopy. K-PEI laminates underwent material separation at much lesser line energy (ratio of laser power to velocity) than K-PP laminates during laser machining. Scanning electron microscopy (SEM) was used to further analyze the laser cut surfaces. A prominent observation on the laser-irradiated surface was: less recast/resolidified polymer covered the Kevlar fabric in K-PEI as compared to a thicker polymeric layer in K-PP. Heat affected zone and damage factors were evaluated using scanning acoustic microscopy (SAM). Surface roughness and kerf width were also analyzed to understand the effect of laser machining of Kevlar laminates. [ABSTRACT FROM AUTHOR]

• High hardness steel (HHS) sheet with UHMWPE composite backing were tested against a hardened steel core projectile. • The projectile core was eroded by the HHS sheet and stopped in UHMWPE composite. • It is observed that only a core eroded to a certain length and weight by armor system can be defeated. • In numerical modeling core failure strain was determined from the residual weight of cores. • The numerical model can be used to evolve armor design. Thin high hardness steel sheets can be an alternative to expensive ceramic armor systems designed to defeat hardened core projectiles. A thin high hardness steel sheet backed with UHMWPE fiber-reinforced composite was ballistically tested against a 7.62 × 39 mm hardened steel core projectile in a single-stage gas gun. Thin steel sheets of 530 BHN hardness were adhesively bonded with UHMWPE fiber-reinforced composite to fabricate armor plates. Armor plates were able to defeat the projectile showing considerable potential. Tensile strength of steel sheet and UHMWPE-fiber reinforced ply was also determined. A detailed numerical simulation of the impact event was also performed to understand the phenomenon of defeat and penetration in greater detail. The numerical model was calibrated from the recovered projectile's core after the ballistic test. [ABSTRACT FROM AUTHOR]

• Vacuum compression moulded Basalt-Polyeteherimide (PEI) composites manufacturing. • Optimization of Basalt-PEI composite manufacturing moulding parameters. • Basalt-PEI composite under quasi-static and dynamic high strain rate loading. • Elastic recovery of Basalt-PEI composite can help in reflecting the blast wave. High temperature blast and ballistic resistant light weight fibre reinforced plastic composites are very much in demand. Accordingly, the present investigation is focused on the quasi-static and high strain rate behaviour of Basalt/Polyetherimide (PEI) composite. Nine different types of composite samples were fabricated by compression moulding. The moulding pressures and temperatures were varied in the range of 15–25 bars and 325 °C−375 °C, respectively. Quasi-static testing was done at the rate of 3 mm/min to establish the optimum moulding parameters. High strain rate compression tests in the strain rate range of 900/s−3200/s were performed on the optimum moulded composite specimens. High strain rate testing revealed that 40 layered Basalt/PEI composite moulded at 25 bar pressure and 350 °C attained highest stress of 932 MPa whereas, the same was found to attain 446 MPa under quasi-static loading conditons. Thus, establishing the rate depedency of Basalt/PEI composite. Damage studies revealed that Basalt/PEI undergoes brittle damage, typically resulting in shear plane angle of 42°−45°. SEM micrographs revealed brittle fibre failure and matrix free fibre bundles, indicating the importance of process parameter optimiation. [ABSTRACT FROM AUTHOR]

Quasi-static tensile test of UHMWPE fiber-reinforced composite laminate is challenging to perform due to low interlaminar shear strength and low coefficient of friction. Tensile tests proposed in the literature were conducted and limitations associated with each method led to the evolution of a new method. Tensile test of single-ply was realized as the best representative of tensile strength of a composite than tensile test of UHMWPE laminate. A fixture was developed for single-ply tests which increased friction and provided the mechanical constraint to slipping. The fixture is easy to fabricate and has provided repeatable results for eight grades of UHMWPE fiber-based (0/90) fabrics. Reported tensile strengths are in quite high range of 900–1500 MPa. • Ballistic composites are quite different from structural composites. • Tensile strength difficult to determine with standard methods. • All available methods tested for efficacy. • A new method is suggested for efficient testing. • Properties of wight commercial grades determined by suggested method. [ABSTRACT FROM AUTHOR]