Search

Active and passive microwave characteristics of diurnal soil freeze-thaw transitions and their relationships are crucial for developing retrieval algorithms of the soil liquid water content (θliq) and freeze/thaw state, which, however, have been less explored. This study investigates these microwave characteristics and relationships via analysis of ground-based measurements of brightness temperature (TB) and backscattering coefficients (σ⁰) in combination with simulations performed with the Tor Vergata discrete radiative transfer model. Both an L-band (1.4 GHz) radiometer ELBARA-III and a wide-band (1-10 GHz) scatterometer are installed in a seasonally frozen Tibetan meadow ecosystem to measure diurnal variations of TB and copolarized σ⁰ at both hh (σhh⁰) and vv (σ vv⁰) polarizations. Analysis of measurements collected between December 2017 and March 2018 shows that 1) diurnal cycles are observed in both TB and σ ⁰ due to the change in surface θliq caused by diurnal soil freeze-thaw transitions; 2) a negatively linear relationship is found between e and σ⁰ regardless of frequency, polarization combinations, and observation angles; 3) slopes (β ) of linearly fit equations between eH and σhh⁰ decrease with increasing observation angles of ELBARA-III, while the ones between eV and σvv⁰ increase with increasing observation angles; and 4) correlations between e and σ⁰ increase with decreasing microwave frequency of σ⁰ measurements and ELBARA-III observation angles, and magnitudes of diurnal σ⁰ cycles also increase with decreasing microwave frequency. Moreover, the calibrated Tor Vergata model shows capability to reproduce both diurnal e and σ⁰ variations as well as to quantify their relationships at different frequencies and observation angles.

The Microwave Radiation Imager (MWRI) sensors aboard on the Chinese FengYun-3 (FY-3) series satellites have a great potential for long-term study of sea ice distribution. This study corrected the newly released FY-3D MWRI brightness temperature (TB) data with the Advanced Microwave Scanning Radiometer 2 (AMSR2) TB data and used an Arctic Radiation and Turbulence Interaction Study Sea Ice (ASI) dynamic tie points algorithm to derive the sea ice concentration (SIC) from these corrected MWRI TB data. We assessed the accuracy of our MWRI-ASI SIC product by comparing with the published SIC products at different spatial resolution and by validating with the Moderate Resolution Imaging Spectroradiometer (MODIS) and Sentinel-1 data. We find that MWRI-ASI SIC has the smallest difference with AMSR2-ASI SIC with the mean absolute difference (MAD) of 6.8%, and the differences mainly occur at the marginal ice zone regions. The MWRI-ASI displays the highest difference with Sea Ice Index and OSI-430-b at 25 km with the mean MAD of 11.8%. MADs between MWRI-ASI SIC and SIC products from other sensors are below 10% except for late June to early October, when those are higher. Compared with the MODIS SIC, MWRI-ASI SIC outperforms other SIC products at the same resolution, with the mean bias of -2.1% and mean RMSD of 13.5%. Although MWRI-ASI tends to under-estimate high SIC, it can capture details of large leads, ice edge, and fragmented ice area. Our MWRI-ASI SIC product at 12.5 km is promising to integrate into long-term sea ice records.

FengYun-3C (FY-3C) is the second-generation polar-orbiting meteorological satellite in China. As one of the most important microwave payloads deployed onboard FY-3C, microwave radiation imager (MWRI) has been continuously observing radiance originating from land and sea surface and supports numerical weather predictions at regional and global scales. With a long-term monitoring of the cold-end reference, MWRI onboard FY-3C was found suffering from discontinuous observations due to its temporary power-OFF/power-ON in the years of 2015 and 2018, resulting in anomalous brightness temperature (TB) jump up to 2–3 K in magnitude at some channels. Analysis of the operating status of FY-3C MWRI indicated that deviation of the receiver system from its optimal operating status affects the nonlinearity characteristics significantly. A correction algorithm, which relates nonlinearity to the autogain control (AGC) operating voltage of the sensor, is thus proposed on the basis of on-ground thermal/vacuum (T/V) test results in the prelaunch phase in order to mitigate the calibration anomalies of FY-3C MWRI. Nonlinearity correction of FY-3C MWRI is further corroborated by comparisons of simultaneously overlapping observations of global precipitation measurement (GPM) microwave imager (GMI). The results demonstrated that after nonlinearity correction the performance of FY-3C MWRI has been improved at all channels except for the 36-V channel where technical failures have been detected since October 2016.

Across spatial and temporal scales, sea-ice motion has implications on ship navigation, the sea-ice thickness distribution, sea ice export to lower latitudes and re-circulation in the polar seas, among others. Satellite remote sensing is an effective way to monitor sea-ice drift globally and daily, especially using the wide swaths of passive microwave missions. Since the late 1990s, many algorithms and products have been developed for this task. Here, we investigate how processing sea-ice drift vectors from the intersection of individual swaths of the Advanced Microwave Scanning Radiometer 2 (AMSR2) mission compares to today's status-quo (processing from daily averaged maps of brightness temperature). We document that the swath-to-swath (S2S) approach results in many more (two orders of magnitude) sea-ice drift vectors than the daily-maps (DM) approach. These S2S vectors also validate better when compared to trajectories of on-ice drifters. For example, the RMSE of the 24 hour Arctic sea-ice drift is 0.9 km for S2S vectors, and 1.3 km for DM vectors from the 36.5 GHz imagery of AMSR2. Through a series of experiments with actual AMSR2 data and simulated Copernicus Imaging Microwave Radiometer (CIMR) data, we study the impact that geo-location uncertainty and imaging resolution have on the accuracy of the sea-ice drift vectors. We conclude by recommending that a swath-to-swath approach is adopted for the future operational Level-2 sea-ice drift product of the CIMR mission. We outline some potential next steps towards further improving the algorithms, and making the user community ready to fully take advantage of such a product.

Objectives: To predict meteorological phenomena such as rain events from sky status during rainy and non-rainy periods. Methods: The method used here is based on brightness temperature ratio measurement at two different frequencies, namely 23.8 GHz and 30 GHz respectively, using ground based dual frequency radiometric data. The ratios of brightness temperature readings obtained by the dual-frequency radiometer at the two above mentioned frequencies are calculated for each simultaneously-taken pair of measurements. Data obtained by the authors for the year 2009 at Cachoeira Paulista in Brazil has been used for analysis. Findings: The major results obtained from the analysis of data collected over a continuous period of seven months are used to construct corresponding histograms and cumulative count graphs of brightness temperature ratios. The histograms and graphs clearly show three peak values that could be interpreted as thresholds between clear sky, cloudy sky and rainy sky conditions respectively. Novelty: The study implements detection of rain events from sky status during rainy and non-rainy periods using peak brightness temperature values obtained from graphs generated using the observation data. The outlined technique can therefore be used to clearly determine sky conditions and accurately predict rain phenomena. The ratio of brightness temperatures at the two frequencies is a unique parameter which is critical to the successful estimation of rain from sky status. The results agree well with multi-channel radiometric data obtained by other researchers at lower frequencies. Keywords: sky status; microwave; millimeter wave; dual frequency radiometer; brightness temperature; rainfall

Based on the spatiotemporally weighted two-step method (STW-TSM), the spatiotemporal characteristics of the residual microwave brightness temperature (MBT) with the Mw7.9 Wenchuan earthquake on May 12, 2008 are revealed by satellite data from the Advanced Microwave Scanning Radiometer - Earth Observing System (AMSR-E) sensor. Two significant MBT positive anomalies are found to be exactly in spatial accordance with two geological Quaternary zones, and the detailed geometric information of the MBT positive anomaly is found to be correlated with the microwave frequencies. After eliminating other possible influential factors, including surface temperature, vegetation index, land-surface roughness, and surface soil moisture under the conditions of space, time, and magnitude, and according to the microwave radiative transfer model, the dielectric variation in the ground surface is suggested to be the primary contributor of the MBT positive anomaly. The positive-hole (P-hole) theory is applied to interpret the geological preference of the MBT positive anomalies through a chain process: crustal stress enhancing—P-hole producing and flowing down stress gradients—surface P-hole accumulating—dielectric constant decreasing—and microwave radiation increasing. The stress-resulting effect of the dielectric decrease on MBT the increase provides a novel mechanism for microwave remote-sensing monitoring of crustal stress field alteration, earthquake preparation, and upcoming shocks. This research has a particular significance for searching potential georelations between the tectonic earthquake preparation and the abnormal satellite MBT.

This study presents a correction algorithm to remove the backlobe intrusion from the hot-load reflector of microwave radiation imager (MWRI) on-board China FengYun-3C (FY-3C) meteorological satellite. Discontinuities in the radiometric gain of MWRI, due to inaccurate backlobe spillover of the hot-load reflector, have been diagnosed. A physical correction method, relating the radiometric gain difference between two distinct backlobe scenes to the spillover of the hot-load reflector, is thus established to estimate the in-orbit spillover factor of the MWRI hot-load reflector. Meanwhile, it is found that brightness temperature (TB) at each 1° × 1° grid could not address the backlobe pattern appropriately, leading to abrupt changes in the radiometric gain occurring near the coastlines. To better represent the backlobe spillover, the effective backlobe TB is now averaged over a 4° × 4° area from advanced microwave scanning radiometer-observed TBs, which is now in a finer resolution of 0.25° × 0.25°. With the adjusted spillover for the hot-load reflector, anomalous behaviors of the radiometric gain are mitigated effectively and the improvement at the coastlines is pronounced, inducing TB variation up to 2 K in magnitude at the 10.65 GHz channel. Although the algorithm presented in this study is only restricted to channel frequencies up to 23.8 GHz due to its accuracy limitation, it could tackle similar issues for those microwave radiometers not capable of in-orbit backlobe maneuvers and receiving the radiances inevitably from the outer edge of the hot-load or cold-sky reflectors.

Global warming is one of the most serious problems we are facing in the 21st Century. Sea ice has an important role of reflecting the solar radiation back into space. However, once sea ice started to melt, the ice-free water would absorb the solar radiation and amplify global warming in the Arctic region. Thus, importance of sea ice monitoring is increasing. Since longer wavelength microwave can penetrate clouds, passive microwave radiometers on-board satellites are powerful tools for monitoring the global distribution of sea ice on daily basis. The Advanced Passive Microwave Scanning Radiometer AMSR2 which was launched by JAXA in May 2012 on-board GCOM-W satellite provides brightness temperature data that are used to estimate sea ice concentration, the fundamental parameter that is used to monitor the sea ice cover. JAXA is providing AMSR2 sea ice concentration data, derived using ASMR2 Bootstrap Algorithm as a standard product of AMSR2, as a means to communicate how the sea ice cover is changing. This paper describes the advantages of AMSR2 in calculating sea ice concentration and evaluate the accuracy of the sea ice concentration in the Sea of Okhotsk by comparing the result with simultaneously collected MODIS data. The result suggested that under normal winter condition, the RMSE of the AMSR2 sea ice concentration could be less than 10%.

The additional microwave radiation from underground rock mass (lithosphere) that is caused by tectonic activity and alternating crustal stress has been shown to be a detectable electromagnetic signal via satellite remote sensing. However, the emission of microwave radiation produced inside the lithosphere will be affected by its overburden matter, such as sand, soil, water, and vegetation, and this effect is unknown. In this article, we use a C-band microwave radiometer to detect the variations in the microwave brightness temperature ( $T_{B}$ ) of rock samples in the process of axial loading. For the rock samples, the surface was bare and covered with dry sand or humid sand. The experimental detection illustrates that the dry sand unexpectedly allows more stress-associated additional radiation ( $\Delta T_{B}$ ) to be received by the radiometer, while humid sand shows significant extinction of $\Delta T_{B}$ . Both the radiative transfer theory and the stress-activated positive hole hypothesis are applied to interpret the mechanisms of the effect of dry and humid sand layers on $\Delta T_{B}$ . The outflow of stress-activated positive holes is from inside the loaded rock, and hence their accumulation beneath the surface of the sand layer is expected to reduce the local dielectric permittivity of sand, thereby making the detected $\Delta T_{B}$ by the microwave radiometer to be larger than that extrapolated theoretically in accordance with radiative transfer theory. This article is valuable for understanding the diverse $T_{B}$ anomalies that have been observed prior to tectonic earthquakes, and it facilitates the evaluation of the potential application of $\Delta T_{B}$ to seismic monitoring and earthquake prediction.

Land surface temperature (LST) is a key parameter and plays an important role in hydrology, ecology, environment, and biogeochemistry. It is difficult for the existing satellites to acquire global LST with spatial and temporal consistency. The Moon-based Earth observation platform with a long life, large coverage can observe continuously the Earth, and obtain the global-scale LST. At present, various approaches for retrieving LST from passive microwave remote sensing data have been developed for the satellite remote sensing data with small and constant viewing zenith angle, however, the Moon-based Earth observation platform located outside the Earth's ionosphere has the viewing zenith angle of 0-90°. In this study, a modified physical-based method of LST retrieval from passive microwave data was developed for wide viewing zenith angles, and the LST and emissivity can be simultaneously estimated through the analysis of various atmospheric and ionosphere parameters. Three types of data, including the FengYun-3B satellite microwave radiation imager data, the multichannel Advanced Microwave Scanning Radiometer data, and Moon-based microwave radiation simulation data with the viewing zenith angles of 52-53°, 55°, and 0-90°, respectively, were used to retrieve LST. Results show that the estimation accuracy of LST decreases with the increase of viewing zenith angle. The 23.8 and 36.5 GHz brightness temperature is optimum for the LST estimation under a large-scale viewing zenith angle, and the root mean square errors of the LST are 5.18, 5.44, and 4.79 K, respectively.

Microwave Imager Combined Active and Passive (MICAP), which is a package of active and passive microwave instruments including L/C/K-band radiometers and L-band scatterometer, has been approved to be taken onbord the Chinese Ocean Salinity Mission. The L-band one-dimensional synthetic aperture radiometer (L-Rad) is the key part of MICAP to measure sea surface salinity (SSS). Since radio frequency interference (RFI) is reported as a serious threat to L-band radiometry, the RFI detection and mitigation techniques must be carefully designed before launch. However, these techniques need to be developed based on the knowledge of how RFI affects complex correlation, visibility function, and reconstructed brightness temperature. This paper presents a time-domain signal modeling method for the simulation of interferometric measurement under RFI’s presences, and a simulation system for L-Rad is established accordingly. Several RFI cases are simulated with different RFI types, parameters, and positions, and the RFI characteristics upon L-Rad’s measurement are discussed. The proposed simulation system will be further dedicated to the design of RFI processing strategy onboard MICAP.

Ground-based multichannel microwave radiometers (GMRs) can observe the atmospheric microwave radiation brightness temperature at K-bands and V-bands and provide atmospheric temperature and humidity profiles with a relatively high temporal resolution. Currently, microwave radiometers are operated in many countries to observe the atmospheric temperature and humidity profiles. However, a theoretical analysis showed that a radiometer can be used to observe solar radiation. In this work, we improved the control algorithm and software of the antenna servo control system of the GMR so that it could track and observe the sun and we use this upgraded GMR to observe solar microwave radiation. During the observation, the GMR accurately tracked the sun and responded to the variation in solar radiation. Furthermore, we studied the feasibility for application of the GMR to measure the absolute brightness temperature (TB) of the sun. The results from the solar observation data at 22.235, 26.235, and 30.000 GHz showed that the GMR could accurately measure the TB of the sun. The derived solar TB measurements were 9950 ± 334, 10,351 ± 370, and 9217 ± 375 K at three frequencies. In a comparison with previous studies, we obtained average percentage deviations of 9.1%, 5.3%, and 4.5% at 22.235, 26.235, and 30.0 GHz, respectively. The results demonstrated that the TB of the sun retrieved from the GMR agreed well with the previous results in the literature. In addition, we also found that the GMR responded to the variation in sunspots and a positive relationship existed between the solar TB and the sunspot number. According to these results, it was demonstrated that the solar observation technique can broaden the field usage of GMR.

Chinese FY-4M is a new-generation geosynchronous satellite, which will be launched in the near future. It is equipped with multichannel millimeter wave radiometers, which operate in the range of 50–430 GHz. This satellite will increase revisit time and significantly improve the monitoring and weather variation forecasting capabilities. Calibration is an important issue for the quantitative analysis and application of brightness temperature observations. Calibration is first conducted in a thermal/vacuum chamber prior to the launch. A hot target onboard the satellite is used to provide relative irradiance for onboard calibration, and the cold cosmos is used as a cold target. However, complicated space conditions may result in many uncertainties and instabilities during calibration. A new method is required to evaluate the performance of the instruments during long-term operation. Because of the non-existence of atmospheric and other environmental interferences, the lunar surface maintains its physical and chemical stability. Thus, it is an ideal source for thermal calibration. The earliest ground-based observation of thermal microwave emission of the Moon dates back to the early 1940s. At that time, the temperature profile and dielectric constant of the lunar surface had not been studied in detail. Thus, interpreting the observed microwave brightness temperature was difficult. In recent years, many studies of the lunar surface have been performed owing to the advances in satellite-borne remote sensing programs. The Diviner Lunar Radiometer Experiment onboard the Lunar Reconnaissance Orbiter investigated the global solar reflectance and mid-IR irradiance. These infrared measurements contribute to the quantitative description of the thermophysical properties of the superficial lunar regolith media. Chinese probes, Chang’e-1 and Chang’e-2, carried four-channel microwave radiometers to observe the microwave thermal emission of the lunar regolith media, which may provide information on superficial dielectric properties of the lunar surface. These advances created a foundation for the millimeter channel observation of the lunar surface. In this study, a real-time model of the sub-solar position and total irradiance of the lunar surface was developed. The altitude of FY-4M is 35800 km. The distance between the Moon and the Earth is between 363400 km (perigee) and 405400 km (apogee). This large distance enables nadir observation from the FY-4M radiometer toward the center region of the lunar equator. The observation beam angle ranges from 0.097° to 0.027°. The diameters of the observation regions at different channels are 750 km (55 GHz), 480 km (89, 118 GHz), 300 km (166, 183 GHz), and 210 km (425 GHz) at apogee. Based on the surface albedo derived from the Clementine data and the constrained thermophysical parameters of the lunar regolith media obtained from the Diviner infrared brightness temperature, the one-dimensional thermal transfer equation is solved to obtain the physical temperature profile of the lunar regolith media. Using the 37-GHz brightness temperature from Chang’e-2 observations, the loss tangent of the regolith media is inverted. Using the fluctuation dissipation theorem, the brightness temperature of the lunar surface in FY-4M millimeter channels is calculated. The thermophysical profile of the regolith can be validated using the Diviner infrared brightness temperature data. The calculated temperature at a depth of 1.3 m is consistent with the measurements obtained in the Apollo heat flow experiment. The surface temperature and millimeter brightness temperature on the lunar equator (0°N, 0°E) during the entire year of 2010 are simulated. The peak value of the brightness temperature is attained after that of the surface physical temperature peak value. In the low frequency channel, the penetration depth increases, its peak value is typically small, and the peak appears later. This study thus presents an effective model for FY-4M calibration and data analysis.

An ultrawideband radiometer was used to measure microwave brightness temperature spectra over Arctic sea ice in the Lincoln Sea near the north coast of Greenland. Spectra over the range of 0.5–2 GHz were compared to thermal infrared images collected during the airborne campaign and also compared to nearly concurrent Sentinel-1 C-band synthetic aperture radar (SAR) data. Based on those comparisons, spectral signatures were associated with thick multiyear ice and thin ice. A radiative transfer (RT) model consisting of a homogeneous slab of sea ice bounded by sea water and air was then used to invert the spectra for sea ice thickness and salinity. Inferred thicknesses were consistent with ice thickness climatology for ice floes in the Lincoln Sea. Salinities are higher than expected which may be a consequence of neglecting surface and volume scattering contributions in the models.

We have developed an algorithm for thin ice detection under winter conditions using the Advanced Microwave Scanning Radiometer 2 (AMSR2) radiometer high-frequency brightness temperature (36 and 89 GHz) L1R swath data, and a method to combine thin ice swath charts to a more reliable daily thin ice chart. Moderate Resolution Imaging Spectroradiometer (MODIS) ice thickness swath charts were used as reference data for the algorithm development. The algorithm is based on the classification of 36-GHz polarization ratio (PR36) and H-polarization 89–36-GHz gradient ratio (GR3689H) signatures with linear discriminant analysis. We applied an atmospheric correction to the AMSR2 L1R data following established sea ice concentration (SIC) retrieval algorithms. The PR36 and GR8936H signatures were adjusted to a constant air temperature ( $T_{a}$ ) before the thin ice detection using an empirical relationship between them and $T_{a}$ . The maximum thickness of detected thin ice was estimated to be 20 cm. The thin ice detection with the L1R data is conducted only when SIC $\ge70$ % and $T_{a}\le -5\,\,^\circ \text{C}$ to limit conditions where thick ice may be erroneously detected as thin ice. The thin ice detection algorithm was developed for the Barents and Kara Seas, but it should also be applicable for other Arctic marginal ice zones (MIZs). The daily thin ice chart was validated using an independent set of MODIS daily ice thickness charts. The average probability for misclassification of thick ice as thin ice was 10% and 32% for vice versa. We demonstrate the use of the daily thin ice chart for monitoring the thin ice fraction in the Barents and Kara Seas.

The water cycle observation mission (WCOM) will build upon previous L and C band passive microwave soil moisture satellite missions. WCOM will consist of a passive microwave synthetic aperture radiometer operating at L , S , and C bands. The WCOM requirements for passive soil moisture are to estimate soil moisture in the top 5 cm of soil layer with an error less than 0.04 m3/m3, at 15-km resolution and with a 3-day revisit. A new set of algorithms for these multi-frequency platforms will need to be developed for estimating the data products at the desired resolution. To accomplish this, a brightness temperature (TB) downscaling methodology is developed that uses passive S -band TB (30 km) to downscale L -band TB (50 km) and to estimate soil moisture at a 30-km resolution, based on the linear relationships between the passive signals of L band and S band. To test this downscaling method, analysis was performed using PALS data from the Soil Moisture Experiments in 2002 (SMEX02). For this study, 4-km L -band observations were downscaled to 800 m. The root mean square errors between the downscaled TBL at 800 m with the observed TBL at 800 m are 2.63 and 1.60 K for H and V polarizations, respectively. The results also showed that it was possible to use these disaggregated TB to estimate soil moisture to meet the mission requirement of 0.04 m3/m3. These results showed that we can obtain higher resolution soil moisture from the L -band passive TB with a high accuracy ( S -band information.

The NASA-sponsored Calibrated Passive Micro- wave Daily Equal-Area Scalable Earth Grid 2.0 Brightness Temperature (CETB) Earth System Data Record Project team has generated a multisensor, multidecadal time series of high-resolution radiometer products designed to support climate studies. This project uses image reconstruction techniques to generate conventional and enhanced-resolution daily brightness temperature images on a standard set of map projections. Sensors included in CETB are the Aqua Advanced Microwave Scanning Radiometer–Earth Observing System (AMSR-E), Scanning Multichannel Microwave Radiometer, and all Special Sensor Microwave/Imager and Special Sensor Microwave Imager/Sounder radiometers. These span frequencies between 6 and 89 GHz. This paper considers the issues of adding the L-band (1.6 GHz) Soil Moisture Active Passive (SMAP) radiometer measurements to the CETB climate record, with emphasis on optimizing the reconstruction to provide the highest possible spatial resolution at the lowest noise level. SMAP radiometer reconstruction on SMAP-standard grids is also considered. Simulation is used to optimize the reconstruction, and the results confirmed using actual data. A comparison of the performance of the Backus–Gilbert approach and the radiometer form of the Scatterometer Image Reconstruction algorithm is provided. These are compared to the conventional drop-in-the-bucket gridded imaging.

Collocated CloudSat rain rates and Advanced Microwave Scanning Radiometer for EOS (AMSR-E) 89-GHz brightness temperature Tb retrievals allow for the development of an algorithm to estimate light, warm rain statistics as a function of AMSR-E 89-GHz Tb for shallow marine clouds. Four statistics are calculated from CloudSat rainfall rate estimates within each 4 km × 6 km Tb pixel sampled by both sensors: the probability of rainfall, the mean rain rate, the mean rate when raining, and the maximum rain rate. Observations with overlying cold clouds are removed from the analysis. To account for confounding variables that modify Tb, curves are fit to the mean relationships between Tb and these four statistics within bins of constant column-integrated water vapor from AMSR-E, and sea surface temperature and wind speed from reanalysis grids. The coefficients that define these curves are then applied to all available AMSR-E Tb retrievals to estimate rain rate throughout the eastern subtropical oceans. A preliminary analysis shows strong agreement between AMSR-E rain rates and the CloudSat training dataset. Comparison with an existing microwave precipitation product shows that the new statistical product has an improved sensitivity to light rain. A climatology for the year 2007 shows that precipitation rates tend to be heavier where the sea surface is warmer and that rain is most frequent where stratocumulus transitions to trade cumulus in the subtropics.

A physically based Bayesian passive microwave precipitation retrieval requires an accurate forward radiative transfer model along with realistic database representation of hydrometeors, atmospheric properties, and surface emission. NASA’s Global Precipitation Measurement (GPM) Mission provides an unprecedented opportunity for the development of such databases, matching a well-calibrated radiometer with dual-frequency radar. Early versions of passive microwave products from GPM utilized a physically constructed database in a Bayesian retrieval scheme, assumed ice particles to be spheres, and used Mie radiative transfer. A large body of recent work demonstrates that this is insufficient for retrieval at the GPM radiometer frequencies. In this paper, the retrieval is updated to use nonspherical particles. Simulated brightness temperature (Tb) agreement with observations is shown to be significantly improved across the high frequencies, decreasing biases significantly and increasing correlations to observed Tb. This is compared with a second identical retrieval performed with the assumption of spherical ice particles, and retrieval results are compared globally, seasonally, and instantaneously for a case study at the rain rate level. While not at the high level of improvement shown in Tb space, the precipitation retrieval is improved as compared to one using observed Tb in correlation, bias, and root-mean-square error. Reported improvements, while modest in magnitude, advance the retrieval to more physical consistency which allows for deeper insight into ice particle properties associated with precipitation.

Consistency between the brightness temperatures observed with a ground-based microwave radiometer and the brightness temperatures computed by forward modeling is important in many different data applications. Using the National Centers for Environmental Prediction-Final Operational Global Analysis (NCEP-FNL) dataset as a reference, the brightness temperature was obtained through the radiation transfer model for forward calculation. The problem of segmented features in long time of observational data from ground-based microwave radiometers (the so-called “jumping problem”) was identified. By analyzing the deviation and correlation between the observational bright temperature data and the forward calculated data under clear sky conditions, a revised scheme is proposed for the bright temperature observational data. Data obtained with a ground-based microwave radiometer in Beijing from January 1, 2010 to December 31, 2011 around the date of liquid nitrogen calibration show that the correlation between the observed brightness temperatures and the forward computed brightness temperatures is better after correction, especially at 28 and 30 GHz. The “jumping” problem in the observational data for the brightness temperature is eliminated after correction and the time continuity of the observational data and its consistency with the forward calculated data based on the NCEP-FNL dataset are improved. The proposed correction scheme can be used both for real-time data quality control and to improve the accuracy of historical datasets obtained with poorly calibrated microwave radiometers or radiometers working in polluted environments.

An enhanced spatial resolution brightness temperature product is proposed for future conical scan microwave radiometers. The technique is developed for Copernicus Imaging Microwave Radiometer (CIMR) measurements that are simulated using the CIMR antenna pattern at the L-band and the measurement geometry proposed in the Phase A study led by Airbus. An inverse antenna pattern reconstruction method is proposed. Reconstructions are obtained using two CIMR configurations, namely, using measurements collected at L-band by the forward (FWD) scans only, and combining forward and backward (FWD+BWD) scans. Two spatial grids are adopted, namely, 3km × 3 km and 36km × 36km. Simulation results, referred to synthetic and realistic reference brightness fields, demonstrate the soundness of the proposed scheme that provides brightness temperature fields reconstructed at a spatial resolution up to ~1.9 times finer than the measured field when using the FWD+BWD combination., This work has been produced for the European Space Agency (ESA) in the frame of the Copernicus programme as a partnership between ESA and the European Commission.

形態: カラー図版あり, Physical characteristics: Original contains color illustrations, Accepted: 2020-11-01, 資料番号: PA2110066000

An advanced algorithm for atmospheric water vapor column (WVC) retrieval from the Advanced Microwave Scanning Radiometer (AMSR) measurements over the Arctic sea ice (SI) and open ocean waters is presented. The algorithm is built on the physical modeling of the brightness temperature (BT) of the microwave radiation of the SI–open ocean–atmosphere system at the AMSR frequencies and polarizations. The BTs are calculated using a data set of the SI, atmospheric, and oceanic parameters changing in the range of their natural variability in the Arctic, and using the SI microwave emission coefficients varied according to the published experimental data. The inverse operator explores neural networks (NNs), trained on an ensemble of modeled BTs. The algorithm is applied both to the AMSR-E and to the AMSR2 measurement data. Validation of the algorithm is performed with radiosonde (r/s) WVC measurements from the four Arctic coastal stations at different SI conditions during 2014–2017. The results of the application of the new algorithm to satellite radiometer measurements are also compared with the Era-Interim reanalysis WVC, as well as with other satellite WVC products, based on the data of the Moderate Resolution Imaging Spectrometer (MODIS) and on the data of the Advanced Microwave Sounding Unit-B (AMSU-B) for 2008 and 2015. To justify the usage of the Era-Interim WVC as a reference data set for the algorithm accuracy estimation in the Arctic area, Era-Interim WVC is also compared with the r/s WVC measurements.

The paper describes a method of simultaneous measurements of kinematic parameters of a high-speed process by a microwave radio interferometer with a 3-mm range of wavelengths and the brightness temperature of the same process by the microwave radio interferometer operating in the radiometer mode. The methods of radiometer calibration and analysis of radiometric data are described. Results of experimental investigations are reported by an example of measuring the detonation velocity and estimating the brightness temperature of the detonation front in TNT.

The Tropical Rainfall Measuring Mission (TRMM) Microwave Imager (TMI), launched in late November 1997, has provided a > 17-year record of tropical precipitation measurements, and prior to the launch of the global precipitation measurements (GPM) satellite in February 2014, the TMI served as the radiometric transfer standard for the TRMM constellation radiometers. Thus, the radiometric calibration of the TRMM constellation radiometers depends upon that of TMI. Therefore, the level-1 TMI brightness temperatures have been reprocessed to produce the TMI legacy brightness temperature product namely 1B11 version 8 (also known as GPM05), which has been released by NASA in late 2017. During this data reprocessing, a radiometric calibration anomaly, associated with the hot load, was discovered. This error was caused by an occasional transient solar intrusion, which introduced a systematic error in the brightness temperature. To remove this error, an independent hot load correction algorithm was implemented. In this paper, the process of identifying the issue, developing the solution, and evaluating the results is described.

This paper describes the technical approach to generate homogeneous warm brightness temperature scene binary mask over the earth for the intercalibration of microwave imagers. The objective is to identify homogeneous desert scenes as targets in radiometric intercalibration of multisource multisensor systems such as Global Precipitation Measurement (GPM) constellation. In this paper, a method is developed to generate mask over continental Australia using 10, 18, and 37 GHz vertical and horizontal polarized radiance observations from GPM Microwave Imager data. Major factors considered are diurnal variation, second Stokes parameter, spatial homogeneity, and surface emissivity. Major advantage of this tool is its minimal, almost negligible, dependence on any external ancillary modeled or observed data.

Accurate estimation of passive microwave land surface emissivity (LSE) is crucial for numerical weather prediction model data assimilation, for microwave retrievals of land precipitation and atmospheric profiles, and for a better understanding of land surface and subsurface characteristics. In this study, global instantaneous LSE is estimated for a 9-yr period from the Advanced Microwave Scanning Radiometer for Earth Observing System (AMSR-E) and for a 5-yr period from the Advanced Microwave Scanning Radiometer 2 (AMSR2) sensors. Estimates of LSE from both sensors were obtained by using an updated algorithm that minimizes the discrepancy between the differences in penetration depths from microwave and infrared remote sensing observations. Concurrent ancillary datasets such as skin temperature from the Moderate Resolution Imaging Spectroradiometer (MODIS) and profiles of air temperature and humidity from the Atmospheric Infrared Sounder are used. The latest collection 6 of MODIS skin temperature is used for the LSE estimation, and the differences between collections 6 and 5 are also comprehensively assessed. Analyses reveal that the differences between these two versions of infrared-based skin temperatures could lead to approximately a 0.015 difference in passive microwave LSE values, especially in arid regions. The comparison of global mean LSE features from the combined use of AMSR-E and AMSR2 with an independent product—Tool to Estimate Land Surface Emissivity from Microwave to Submillimeter Waves (TELSEM2)—shows spatial pattern correlations of order 0.92 at all frequencies. However, there are considerable differences in magnitude between these two LSE estimates, possibly because of differences in incidence angles, frequencies, observation times, and ancillary datasets.

The Microwave Radiation Imager (MWRI) on board Chinese Fengyun-3 (FY-3) satellites provides measurements at 10.65, 18.7, 23.8, 36.5, and 89.0 GHz with both horizontal and vertical polarization channels. Brightness temperature measurements of those channels with their central frequencies higher than 19 GHz from satellite-based microwave imager radiometers had traditionally been used to retrieve cloud liquid water path (LWP) over ocean. The results show that the lowest frequency channels are the most appropriate for retrieving LWP when its values are large. Therefore, a modified LWP retrieval algorithm is developed for retrieving LWP of different magnitudes involving not only the high frequency channels but also the lowest frequency channels of FY-3 MWRI. The theoretical estimates of the LWP retrieval errors are between 0.11 and 0.06 mm for 10.65- and 18.7-GHz channels and between 0.02 and 0.04 mm for 36.5- and 89.0-GHz channels. It is also shown that the brightness temperature observations at 10.65 GHz can be utilized to better retrieve the LWP greater than 3 mm in the eyewall region of Super Typhoon Neoguri (2014). The spiral structure of clouds within and around Typhoon Neoguri can be well captured by combining the LWP retrievals from different frequency channels.

Satellite and ground-based microwave radiometers are routinely used for the retrieval of liquid water path (LWP) under all atmospheric conditions. The retrieval of water vapor and LWP from ground-based radiometers during rain has proved to be a difficult challenge for two principal reasons: the inadequacy of the nonscattering approximation in precipitating clouds and the deposition of rain drops on the instrument’s radome. In this paper, we combine model computations and real ground-based, zenith-viewing passive microwave radiometer brightness temperature measurements to investigate how total, cloud, and rain LWP retrievals are affected by assumptions on the cloud drop size distribution (DSD) and under which conditions a nonscattering approximation can be considered reasonably accurate. Results show that until the drop effective diameter is larger than ~200 $\mu \text{m}$ , a nonscattering approximation yields results that are still accurate at frequencies less than 90 GHz. For larger drop sizes, it is shown that higher microwave frequencies contain useful information that can be used to separate cloud and rain LWP provided that the vertical distribution of hydrometeors, as well as the DSD, is reasonably known. The choice of the DSD parameters becomes important to ensure retrievals that are consistent with the measurements. A physical retrieval is tested on a synthetic data set and is then used to retrieve total, cloud, and rain LWP from radiometric measurements during two drizzling cases at the atmospheric radiation measurement Eastern North Atlantic site.

In previous studies, remote sensing properties of hailstorms have been discussed using various spaceborne sensors. Relationships between hail occurrence and strong passive microwave brightness temperature depressions have been established. Using a 16-yr precipitation-feature database derived from the Tropical Rainfall Measuring Mission (TRMM) satellite, the performance of the TRMM Precipitation Radar and TRMM Microwave Imager is further investigated for hail detection. Detection criteria for hail larger than 19 mm are separately developed from Ku-band radar reflectivity and microwave brightness temperature properties of precipitation features that are collocated with surface hail reports over the southeastern and south-central United States. A threshold of 44 dBZ at −22°C is found to have the highest critical success index and Heidke skill score. The threshold of 230 K at 37 GHz yields the best scores among passive microwave properties. Using these two thresholds, global distributions of possible hail events are generated over 65°S–65°N using two years of observations from the Global Precipitation Measurement Core Observatory satellite. Differences in the derived hail geographical distributions are found between radar and passive microwave methods over tropical South America, the “Maritime Continent,” west-central Africa, Argentina, and South Africa. These discrepancies result from different vertical structures of the maximum radar reflectivity profiles over these regions relative to the southeastern and south-central United States, where the thresholds were established. Those differences generally led to overestimates in the tropics from the passive microwave methods, relative to the radar-based methods.

A conical cavity has been designed and fabricated for use as a broadband passive microwave calibration source, or blackbody, at the National Institute of Standards and Technology. The blackbody will be used as a national primary standard for brightness temperature and will allow for the prelaunch calibration of spaceborne radiometers and calibration of ground-based systems to provide traceability among radiometric data. The conical geometry provides performance independent of polarization, minimizing reflections, and standing waves, thus having a high microwave emissivity. The conical blackbody has advantages over typical pyramidal array geometries, including reduced temperature gradients and excellent broadband electromagnetic performance over more than a frequency decade. The blackbody is designed for use between 18 and 230 GHz, at temperatures between 80 and 350 K, and is vacuum compatible. To approximate theoretical blackbody behavior, the design maximizes emissivity and thus minimizes reflectivity. A newly developed microwave absorber is demonstrated that uses cryogenically compatible, thermally conductive two-part epoxy with magnetic carbonyl iron (CBI) powder loading. We measured the complex permittivity and permeability properties for different CBI-loading percentages; the conical absorber is then designed and optimized with geometric optics and finite-element modeling, and finally, the reflectivity of the resulting fabricated structure is measured. We demonstrated normal incidence reflectivity considerably below −40 dB at all relevant remote sensing frequencies.

Scattering differences induced by frozen particle microphysical properties are investigated, using the vertically (V) and horizontally (H) polarized radiances from the Global Precipitation Measurement (GPM) Microwave Imager (GMI) 89 and 166 GHz channels. It is the first study on frozen particle microphysical properties on a global scale that uses the dual-frequency microwave polarimetric signals.From the ice cloud scenes identified by the 183.3 ± 3 GHz channel brightness temperature (Tb), we find that the scattering by frozen particles is highly polarized, with V–H polarimetric differences (PDs) being positive throughout the tropics and the winter hemisphere mid-latitude jet regions, including PDs from the GMI 89 and 166 GHz TBs, as well as the PD at 640 GHz from the ER-2 Compact Scanning Submillimeter-wave Imaging Radiometer (CoSSIR) during the TC4 campaign. Large polarization dominantly occurs mostly near convective outflow regions (i.e., anvils or stratiform precipitation), while the polarization signal is small inside deep convective cores as well as at the remote cirrus region. Neglecting the polarimetric signal would easily result in as large as 30 % error in ice water path retrievals. There is a universal bell curve in the PD–TBV relationship, where the PD amplitude peaks at ∼ 10 K for all three channels in the tropics and increases slightly with latitude (2–4 K). Moreover, the 166 GHz PD tends to increase in the case where a melting layer is beneath the frozen particles aloft in the atmosphere, while 89 GHz PD is less sensitive than 166 GHz to the melting layer. This property creates a unique PD feature for the identification of the melting layer and stratiform rain with passive sensors.Horizontally oriented non-spherical frozen particles are thought to produce the observed PD because of different ice scattering properties in the V and H polarizations. On the other hand, turbulent mixing within deep convective cores inevitably promotes the random orientation of these particles, a mechanism that works effectively in reducing the PD. The current GMI polarimetric measurements themselves cannot fully disentangle the possible mechanisms.

Vicarious cold calibration (VCC) for spaceborne microwave radiometers is analyzed and modified for application to conical scanning microwave imagers at frequencies from 6 to 90 GHz. The details of the algorithm are modified to account for additional frequencies and polarizations that were not included in the development of the original algorithm. The modified algorithm is shown to produce a more stable cold reference brightness temperature (TB) than the original algorithm. An analysis is performed of this updated algorithm to show the global regions that contribute to the derivation of the cold reference TB and to show which geophysical parameters contribute to the coldest TBs. The analysis suggests that water vapor variability has the largest impact on the TBs in the VCC algorithm. The modified VCC algorithm is applied to microwave imager data and is used as an intercalibration method. It is shown to agree well with other intercalibration methods, demonstrating that it is a valid and accurate method for calibration of microwave imagers.

The self-designed HaiYang-2B (HY-2B) satellite was launched on 24 October 2018 in China at 22:57 UT in a 99.34&deg, inclination sun-synchronous orbit. The Scanning Microwave Radiometer (SMR) on the core observatory has the capability to provide near-real-time multi-channel brightness temperature (Tb) observations, which are designed mainly for improving the level of marine forecasting and monitoring, serving the development and utilization of marine resources. After internal calibration and ocean calibration, the first effort to retrieve land surface snow parameters was performed in this study, which obtained extremely low accuracy both in snow extent and snow mass. Accordingly, land inter-sensor calibration was carried out between SMR and the Advanced Microwave Scanning Radiometer 2 (AMSR2) in order to broaden the research and application of SMR data on the Earth&rsquo, s land surface. Finally, we evaluated the consistency of the snow extent and snow mass derived from the initial and land-calibrated SMR data. The results indicated that a systematic SMR cold deviation whose magnitude depends on the channel is present for all the compared channels. After intercalibration, the conformity of the snow extent and snow mass were substantially improved compared to before, the relative bias of the snow extent and snow mass decreased from &minus, 49.97% to 2.97% and from &minus, 51.71% to 3.01%, respectively.

Accurate representation of the ocean-atmosphere coupling in weather, wave and climate models requires reliable estimates of air-sea surface fluxes of momentum, heat and mass. Whitecap fraction (W) usually quantifies the enhancement of the surface fluxes due to wave breaking. Satellite-based passive remote sensing of W from ocean surface brightness temperatures ( T B s) observes open ocean surface fluxes at low spatial resolution. Radiometric surface observations at higher resolution are necessary to monitor the complex environment in the coastal zone and in polar regions. We assess the feasibility of using the millimeter-wave frequencies (89 to 150 GHz) to observe whitecaps. We evaluate the derivative of the T B with respect to W as a measure for the observation of W. We describe the models and data used to evaluate the T B sensitivity to W for different instrumental and environmental conditions. Atmospheric absorption limits the ability to observe the surface at millimeter-wave frequencies. We find that the T B sensitivity to W at 89 GHz may be sufficient to support limited W retrieval from observations at altitudes below 1 km and that the T B sensitivity at 113 and 150 GHz is not sufficient. Clear skies, and low to moderate atmospheric humidity favor whitecap observations.

In this study, we address the variations of bare soil surface microwave brightness temperatures and evaluate the performance of a dielectric mixing model over the desert of Kuwait. We use data collected in a field survey and data obtained from NASA Soil Moisture Active Passive (SMAP), European Space Agency Soil Moisture and Ocean Salinity (SMOS), Advanced Microwave Scanning Radiometer 2 (AMSR2), and Special Sensor Microwave/Imager (SSM/I). In situ measurements are collected during two intensive field campaigns over bare, flat, and homogeneous soil terrains in the desert of Kuwait. Despite the prevailing dry desert environment, a large range of soil moisture values was monitored, due to precedent rain events and subsequent dry down. The mean relative difference (MRD) is within the range of &plusmn, 0.005 m3&middot, m&minus, 3 during the two sampling days. This reflects consistency of soil moisture in space and time. As predicted by the model, the higher frequency channels (18 to 19 GHz) demonstrate reduced sensitivity to surface soil moisture even in the absence of vegetation, topography and heterogeneity. In the 6.9 to 10.7 GHz range, only the horizontal polarization is sensitive to surface soil moisture. Instead, at the frequency of 1.4 GHz, both polarizations are sensitive to soil moisture and span a large dynamic range as predicted by the model. The error statistics of the difference between observed satellite brightness temperature (Tb) (excluding SMOS data due to radio frequency interference, RFI) and simulated brightness temperatures (Tbs) show values of Root Mean Square Deviation (RMSD) of 5.05 K at vertical polarization and 4.88 K at horizontal polarization. Such error could be due to the performance of the dielectric mixing model, soil moisture sampling depth and the impact of parametrization of effective temperature and roughness.

The Canadian Arctic Archipelago (CAA) presents unique challenges to the determination of melt onset (MO) using remote sensing data. High spatial resolution data is required to discern melt onset among the islands and narrow waterways of the region. Current passive microwave retrievals use daily averaged 19 GHz and 37 GHz data from the multi-channel microwave radiometer (SMMR) and/or the special sensor microwave/imager (SSM/I). The development of a new passive microwave melt onset method capable of using higher resolution data is desirable. The new passive microwave melt onset method described here, named the Dynamic Threshold Variability Method (DTVM), uses higher resolution data from the 37 GHz vertically-polarized channel from the advanced microwave scanning radiometers (AMSR-E and AMSR-2). The DTVM MO detection methodology differs from previously presented passive microwave Arctic MO methods in that it does not use a fixed threshold of a brightness temperature parameter. Instead, the DTVM determines MO dates based on the distribution of dates corresponding to the exceedance of a range of brightness temperature variability thresholds. The method also uses swath data instead of daily averaged brightness temperatures, which is found to lead to improved melt detection. Two current passive microwave MO methods are compared and evaluated for applicability in the CAA alongside the DTVM. The DTVM provides MO dates at a higher spatial resolution than earlier methods in addition to higher correlation with MO dates from surface air temperature (SAT) reanalyses. It is found that, for some years, MO dates in the CAA exhibit a latitudinal dependence, while in other years the MO dates in the CAA are relatively uniform across the domain.

The integral of lightning current squared over time, named as the “lightning action integral”, is an indicator of Joule heat generated by lightning discharge. The temperature of air molecules is thus increased, which can be observed by a ground-based microwave radiometer for atmospheric temperature remote sensing. Observational experiments were performed in early summer in 2017 with a ground-based, MWP967KV type microwave radiometer, which is commonly used for atmospheric temperature profile remote sensing but has been properly-configured this study in order to observe the artificially triggered lightning events at Guangzhou field experiment site for lightning research and test (GFESL). Data from the radiometer and the instrument for recording lightning current have been analyzed and the results from 7 effective events show that a relationship like ΔTB=exp(aX) may exist between the brightness temperature increment, ΔTB, in unit of K, observed in 30-50GHz band and the lightning action integral, X, in unit of A2s, calculated from high temporal resolution lightning current records. The correlation coefficient is as high as 0.8863 while the coefficient, a, is equal to 6.25381*10−5 (sample size = 7).

This paper describes the Passive microwave Neural network Precipitation Retrieval algorithm for climate applications (PNPR-CLIM), developed with funding from the Copernicus Climate Change Service (C3S), implemented by ECMWF on behalf of the European Union. The algorithm has been designed and developed to exploit the two cross-track scanning microwave radiometers, AMSU-B and MHS, towards the creation of a long-term (2000–2017) global precipitation climate data record (CDR) for the ECMWF Climate Data Store (CDS). The algorithm has been trained on an observational dataset built from one year of MHS and GPM-CO Dual-frequency Precipitation Radar (DPR) coincident observations. The dataset includes the Fundamental Climate Data Record (FCDR) of AMSU-B and MHS brightness temperatures, provided by the Fidelity and Uncertainty in Climate data records from Earth Observation (FIDUCEO) project, and the DPR-based surface precipitation rate estimates used as reference. The combined use of high quality, calibrated and harmonized long-term input data (provided by the FIDUCEO microwave brightness temperature Fundamental Climate Data Record) with the exploitation of the potential of neural networks (ability to learn and generalize) has made it possible to limit the use of ancillary model-derived environmental variables, thus reducing the model uncertainties’ influence on the PNPR-CLIM, which could compromise the accuracy of the estimates. The PNPR-CLIM estimated precipitation distribution is in good agreement with independent DPR-based estimates. A multiscale assessment of the algorithm’s performance is presented against high quality regional ground-based radar products and global precipitation datasets. The regional and global three-year (2015–2017) verification analysis shows that, despite the simplicity of the algorithm in terms of input variables and processing performance, the quality of PNPR-CLIM outperforms NASA GPROF in terms of rainfall detection, while in terms of rainfall quantification they are comparable. The global analysis evidences weaknesses at higher latitudes and in the winter at mid latitudes, mainly linked to the poorer quality of the precipitation retrieval in cold/dry conditions.

Ground-based multichannel microwave radiometers can observe the atmospheric microwave radiation brightness temperature and continuously provide temperature and humidity profiles of the troposphere. At present, microwave radiometers are operated in many countries for monitoring climate and meteorological phenomena, and there have been many microwave radiometers of this kind presently implemented in China, but they lack a unified monitor for their operational condition, which is necessary if they are taken as a network. For this reason, a real-time monitoring receiving system of radiometer is fundamental and important. In order to check the system stability and the antenna performances, this paper studied the feasibility of applying the solar signals to monitor the antenna alignment, antenna pattern and stability of a radiometer system in working for operational field applications. An experiment was performed and the results from the analysis of the annual variation features with long-term solar observation data at four frequencies, 22.235, 26.235, 30.000 and 51.250 GHz, show that an antenna pattern retrieved from solar observations agrees well with that retrieved from the traditional method. In addition, a daily analysis of the solar signals in online data of a radiometer can be used for monitoring the alignment of the antenna and the stability of the ground-based microwave radiometer system.

A precipitating marine cumulus cloud simulation is coupled to radiation propagation models to simulate active and passive microwave observations at 94 GHz. The simulations are used to examine the error characteristics of the total water path retrieved from the integral constraints of the passive microwave brightness temperature or the path-integrated attenuation (PIA) using a spatial interpolation technique. Three sources of bias are considered: 1) the misdetection of cloudy pixels as clear, 2) the systematic differences in the column water vapor between cloudy and clear skies, and 3) the nonuniform beamfilling effects on the observables. The first two sources result in biases on the order of 5–10 g m−2 of opposite signs that tend to cancel. The third source results in a bias that increases monotonically with the water path that approaches 50%. Nonuniform beamfilling is sensitive to footprint size. Random error results from both instrument measurement precision and the natural variability in the relationship between the water path and the observables. Random errors for the retrievals using the CloudSat PIA are estimated to be the larger of either 20 g m−2 or 30%. A radar/radiometer system with a measurement precision of 0.3 K or 0.05 dB could reduce this error to the larger of either 10 g m−2 or 30%. All error mechanisms reported here result from variability in either the spatial structure of the atmosphere or the hydrometeor drop size distribution. The results presented here are specific to the cloud simulation and in general the magnitude will vary globally.

The choices of the parameterizations for each component in a microwave emission model have significant effects on the quality of brightness temperature (Tb) simulation. How to reduce the uncertainty in the Tb simulation is investigated by adopting a statistical post-processing procedure with the Bayesian model averaging (BMA) ensemble approach. The simulations by the community microwave emission model (CMEM) coupled with the community land model version 4.5 (CLM4.5) over mainland China are conducted by the 24 configurations from four vegetation opacity parameterizations (VOPs), three soil dielectric constant parameterizations (SDCPs), and two soil roughness parameterizations (SRPs). Compared with the simple arithmetical averaging (SAA) method, the BMA reconstructions have a higher spatial correlation coefficient (larger than 0.99) than the C-band satellite observations of the advanced microwave scanning radiometer on the Earth observing system (AMSR-E) at the vertical polarization. Moreover, the BMA product performs the best among the ensemble members for all vegetation classes, with a mean root-mean-square difference (RMSD) of 4K and a temporal correlation coefficient of 0.64.

Passive microwave radiometers on-board satellites can penetrate clouds and can monitor the global sea ice distribution on daily basis. The authors have developed an algorithm to extract thin ice area in the Sea of Okhotsk from the passive microwave sensor AMSR2 on-board GCOM-W1 satellite. The algorithm uses the brightness temperature scatter plots of AMSR2 19 GHz polarization difference(V–H) vs. 19 GHz V polarization. The results were verified using simultaneously collected MODIS images in the Sea of Okhotsk. The most of the thin ice areas visually identified in the MODIS images were automatically extracted from AMSR2 data using the algorithm.

This paper considers some of the issues of radiometer brightness image formation and reconstruction for use in the NASA-sponsored Calibrated Passive Microwave Daily Equal-Area Scalable Earth Grid 2.0 Brightness Temperature Earth System Data Record project, which generates a multisensor multidecadal time series of high-resolution radiometer products designed to support climate studies. Two primary reconstruction algorithms are considered: the Backus-Gilbert approach and the radiometer form of the scatterometer image reconstruction (SIR) algorithm. These are compared with the conventional drop-in-the-bucket (DIB) gridded image formation approach. Tradeoff study results for the various algorithm options are presented to select optimum values for the grid resolution, the number of SIR iterations, and the BG gamma parameter. We find that although both approaches are effective in improving the spatial resolution of the surface brightness temperature estimates compared to DIB, SIR requires significantly less computation. The sensitivity of the reconstruction to the accuracy of the measurement spatial response function (MRF) is explored. The partial reconstruction of the methods can tolerate errors in the description of the sensor measurement response function, which simplifies the processing of historic sensor data for which the MRF is not known as well as modern sensors. Simulation tradeoff results are confirmed using actual data.

Multi-instrument, ground-based measurements provide unique and comprehensive data sets of the atmosphere for a specific location over long periods of time and resulting data compliment past and existing global satellite observations. This paper explores the effect of ice hydrometeors on ground-based, high-frequency passive microwave measurements and attempts to isolate an ice signature for summer seasons at Summit, Greenland, from 2010 to 2013. Data from a combination of passive microwave, cloud radar, radiosonde, and ceilometer were examined to isolate the ice signature at microwave wavelengths. By limiting the study to a cloud liquid water path of 40 g m−2 or less, the cloud radar can identify cases where the precipitation was dominated by ice. These cases were examined using liquid water and gas microwave absorption models, and brightness temperatures were calculated for the high-frequency microwave channels: 90, 150, and 225 GHz. By comparing the measured brightness temperatures from the microwave radiometers and the calculated brightness temperature using only gas and liquid contributions, any residual brightness temperature difference is due to emission and scattering of microwave radiation from the ice hydrometeors in the column. The ice signature in the 90, 150, and 225 GHz channels for the Summit Station summer months was isolated. This measured ice signature was then compared to an equivalent brightness temperature difference calculated with a radiative transfer model including microwave single-scattering properties for several ice habits. Initial model results compare well against the 4 years of summer season isolated ice signature in the high-frequency microwave channels.