Search

As an emerging science, tissue engineering and regenerative medicine focus on developing materials to replace, restore or improve organs or tissues and enhancing the cellular capacity to proliferate, migrate and differentiate into different cell types and specific tissues. Renewable resources have been used to develop new materials, resulting in attempts to produce various environmentally friendly biomaterials. Poly (lactic acid) (PLA) is a biopolymer known to be biodegradable and it is produced from the fermentation of carbohydrates. PLA can be combined with other polymers to produce new biomaterials with suitable physicochemical properties for tissue engineering applications. Here, the advances in modified PLA as tissue engineering materials are discussed in light of its drawbacks, such as biological inertness, low cell adhesion, and low degradation rate, and the efforts conducted to address these challenges toward the design of new enhanced alternative biomaterials. [ABSTRACT FROM AUTHOR]

This work investigates the rheological behavior and characteristics of solutions and convened biopolymer films from Chitosan (Chi) modified by kombucha-derived bacterial cellulose (KBC). The Arrhenius equation and the Ostwald de Waele model (power-law) revealed that the Chi/KBC solutions exhibited non-Newtonian behavior. Both temperature and KBC concentration strongly affected their solution viscosity. With the selection of a proper solvent for chitosan solubilization, it may be possible to improve the performances of chitosan films for specific applications. The elasticity of the prepared films containing KBC 10% w/w was preferable when compared to the controls. FTIR analysis has confirmed the presence of bacterial cellulose, chitosan acetate, and chitosan lactate as the corresponding components in the produced biopolymer films. The thermal behaviors of the Chi (lactic acid)/KBC samples showed slightly higher stability than Chi (acetic acid)/KBC. Generally, these results will be helpful in the preparation processes of the solutions and biopolymer films of Chi dissolved in acetic or lactic acid modified by KBC powder to fabricate food packaging, scaffolds, and bioprinting inks, or products related to injection or direct extrusion through a needle. [ABSTRACT FROM AUTHOR]

Natural fibre biopolymer composites with both fibres and matrix being derived from biomaterials are increasingly used in demanding applications, such as sensing, packaging, building, and transport, and require good electrical, thermal, and flame retardant properties. Herein, an investigation of the effectiveness of functionalising nonwoven cotton/poly(lactic acid) (PLA) fibre mats with graphene oxide nanosheets has been reported by using a facile dip-coating method followed by thermal reduction for enhancing the electric, thermal, and abrasion-resistance properties. The manufacturing processes for preparing biocomposites and introducing functionality are readily scalable. Experimental results reveal that with the addition of less than 0.5 wt% graphene nanoplatelets, the biocomposites showed significant improvements in abrasion resistance, electrical conductivity, thermal conductivity, and diffusivity. Furthermore, the composite shows excellent piezo-resistivity to act as strain sensors with a gauge factor of 2.59 at strains up to 1%. [ABSTRACT FROM AUTHOR]

Fungal biomass (FB), a by-product of the fermentation processes produced in large volumes, is a promising biomaterial that can be incorporated into poly(lactic acid) (PLA) to develop enhanced biocomposites that fully comply with the biobased circular economy concept. The PLA/FB composites, with the addition of triethyl citrate (TEC) as a biobased plasticizer, were fabricated by a microcompounder at 150 °C followed by injection molding. The effects of FB (10 and 20 wt %) and TEC (5, 10, and 15 wt %) contents on the mechanical, thermal and surface properties of the biocomposites were analyzed by several techniques. The PLA/FB/TEC composites showed a rough surface in their fracture section. A progressive decrease in tensile strength and Young's modulus was observed with increasing FB and TEC, while elongation at break and impact strength started to increase. The neat PLA and biocomposite containing 10% FB and 15% TEC exhibited the lowest (3.84%) and highest (224%) elongation at break, respectively. For all blends containing FB, the glass transition, crystallization and melting temperatures were shifted toward lower values compared to the neat PLA. The incorporation of FB to PLA thus offers the possibility to overcome one of the main drawbacks of PLA, which is brittleness. [ABSTRACT FROM AUTHOR]

This research aimed to investigate the effects of using wood leachate (WL) powder as a cost-effective filler added to novel poly (lactic acid) biocomposites and evaluate their mechanical, thermal, morphological, and antibacterial properties. Fourier transform infrared spectroscopy (FTIR), tensile test, Charpy impact test, Shore hardness, scanning electron microscope (SEM), differential scanning calorimetry (DSC), contact angle, and bacterial growth inhibition tests were employed to characterize the developed biocomposites. The SEM results indicated a proper filler dispersion in the polymer matrix. WL powder improved the hydrophobic nature in the adjusted sample's contact angle experiment. Markedly, the results showed that the addition of WL filler improved the mechanical properties of the fabricated biocomposites. The thermal analysis determined the development in crystallization behavior and a decline in glass transition temperature (Tg) from 60.1 to 49.3 °C in 7% PLA-WL biocomposites. The PLA-WL biocomposites exhibited an antibacterial activity according to the inhibition zone for Escherichia coli bacteria. The developed novel PLA-WL composites can be effectively utilized in various value-added industrial applications as a sustainable and functional biopolymer material. [ABSTRACT FROM AUTHOR]

Abstract: An Environmental Stress Cracking test was used to investigate damage to glass fiber reinforced poly(lactic acid) based biocomposites. The study was performed in water. The main advantages were a significant decrease in experiment duration compared to natural, artificial or accelerated tests and an increase in the reliability of the results. Depending on the specific nature of the glass fiber used, significant types of failure behavior were observed. [Copyright &y& Elsevier]