Search

There are principally two mechanisms to improve the impact resistance of polymer-based composites, intrinsic toughening and extrinsic toughening. But the interplay between them is far from being well understood. Here, glass fiber was incorporated into polypropylene to promote extrinsic toughening mechanism, while addition of elastomer and annealing were adopted for intrinsic toughening. In this way, the interaction among glass fiber, elastomer and annealing could be discussed based on various characterizations, and their combined effect on mechanical properties of the composites could be determined. The results show that the intrinsic toughening mechanism of elastomer will be suppressed by glass fiber irrespective of the support of annealing, though annealing could work synergistically with glass fiber to toughen polypropylene. The possible structure-property relations are discussed. This work will provide deeper insight into the toughening behavior of polymer composites and practical guidance for the design of composites with excellent stiffness-toughness balance. [ABSTRACT FROM AUTHOR]

As a novel thermoplastic elastomer, olefin block copolymers (OBCs) show a tremendous application potential in many areas. However, the practical use of OBCs is mainly restricted to the low load-bearing environments because of its poor low-strain mechanical strength and stiffness. In this work, short Kevlar fiber was introduced into OBC matrix to improve its mechanical properties. The results show that introduction of pristine Kevlar fiber only gives rise to a slight increase in tensile strength of OBC owing to the poor interfacial strength, regardless of the presence of compatibilizer maleic anhydride-grafted polypropylene (MA-g-PP). However, a largely enhanced tensile strength can be easily obtained when hydrolyzed or polydopamine-coated Kevlar fiber was incorporated into the OBC matrix using the MA-g-PP as the reactive compatibilizer. More importantly, the tensile strength can be further enhanced with the orientation of Kevlar fiber in the composites. As compared with compression molded composites with randomly orientated fibers, injection molded composites with highly oriented fibers exhibit a significantly higher tensile strength at the same composition. Moreover, it is interesting to observe that Kevlar fiber can be easily exfoliated into several microfibers during melt-mixing with OBC, but the exfoliation has no evident effect on the reinforcement effect possibly because of the poor interfacial strength between the newly-formed microfibers and the OBC matrix. Our work demonstrates that mechanical performance of short fiber reinforced elastomer composites could be significantly improved by enhancing interfacial strength and fiber orientation using a facile surface modification strategy and conventional melt-processing technology. [ABSTRACT FROM AUTHOR]

Abstract: β-Modification and annealing were adopted to improve the impact strength of long glass fiber reinforced (LFPP) composites. It was found that either β-modification or annealing is an efficient way to toughen LFPP composites, and largely enhanced impact toughness can be achieved via simultaneously using β-modification and annealing, particularly for the toughness at low temperatures (−40°C to −20°C). Meanwhile, the tensile strength and Young’s modulus of the composites could be maintained. Various characterizations were used to understand the microstructure changes and toughening mechanism after β-modification and annealing. The results show that the higher extent of the matrix plastic deformation could be the main reason for the enhanced toughness as induced by β-modification and annealing. The possible structural origins for the higher extent of matrix plastic deformation are also discussed. [Copyright &y& Elsevier]

Abstract: Sodium hydrosulfite is used to reduce graphite oxide in current study. The preparation of poly (vinyl alcohol) (PVA)/graphene nanocomposites is realized using two simple steps: the synthesis of PVA/graphite oxide (GO) nanocomposites film and immersion of such a film in the reducing agent aqueous solution. This method prohibits the agglomeration of GO during direct reduction in PVA/GO aqueous solution, and opens a new way to scale up the production of graphene nanocomposites using a simple reducing agent. A 40% increase in tensile strength and 70% improvement in elongation at break have been obtained with only the addition of 0.7wt.% of reduced graphite oxide. Furthermore, a good level of conductivity and a variation in the surface property of the prepared films have been observed for the composites containing graphene. [Copyright &y& Elsevier]