Search

The effects of Ag content and hot-rolling on the microstructure and mechanical properties of Zn-1.5Cu-xAg-0.1Zr(x = 0, 0.1, 0.5, 1.0) alloys were investigated. The microstructure, phase composition and fracture morphology of the alloys were observed and analyzed by optical microscope, x-ray diffraction, scanning electron microscope, energy dispersive spectrometer and universal mechanical testing machine. The results show that Ag has the effect of grain refinement. After alloying, the grain size of as-cast Zn-1.5Cu-xAg-0.1Zr alloy decreased first and then increased, and the minimum grain size of as-cast Zn-1.5Cu-0.5Ag-0.1Zr alloy was refined to 64.18 μm. At the same time, new phase AgZn3 began to precipitate, the yield strength (YS), ultimate tensile strength (UTS), and elongation (EL) of alloys were also up to 97.35 MPa, 139.25 MPa and 7.60%, respectively. After hot-rolling, the grain of Zn-1.5Cu-xAg-0.1Zr alloy was broken and new phase CuZn5 was precipitated. The mechanical properties were significantly improved, and the maximum YS, UTS and EL of as-rolled Zn-1.5Cu-1.0Ag-0.1Zr alloy were 218.14MPa, 244.83MPa, 64.50%, respectively. [ABSTRACT FROM AUTHOR]

The development of magnesium alloys with superior plasticity and favorable strength is still challenging in aerospace industry. Herein, hot extruded Mg-xNd-2.0Sm-0.4Zn-0.4Zr alloys (x = 0, 0.5, 1.0, 1.5, 2.0 and 2.5 wt.%) were rationally designed and easily prepared in order to implement the favorable combination of strength and plasticity. The effects of Nd element addition on the microstructure and mechanical properties of the hot extruded alloys were systematically investigated by optical microscopy (OM), scanning electron microscope (SEM) and transmission electron microscopy (TEM). The OM results indicated that the grain size of the hot extruded alloys decreased from 27.1 to 14.1 μm with increasing Nd addition from 0 to 2.5 wt.%. Some coarse β phases existed at the grain boundary when the addition of Nd element increased to 2.0 wt.%. The TEM results showed that the nanoscaled basal lamellar precipitates, granular precipitates and prismatic lamellar precipitates formed in α-Mg matrix. And the amount of precipitated phase increased obviously with the increase of Nd element addition. The ultimate tensile strength increased significantly from 203 ± 3.0 to 237 ± 2.5 MPa, and the elongation decreased from 30.5 to 21.2 % when the Nd elements increased from 0 to 2.5 wt.%. The fractographs of the hot extruded alloys could be classified as ductile fracture. [ABSTRACT FROM AUTHOR]

Al–Si base composites reinforced with different mixtures of Ni and nano-Al 2 O 3 particles have been fabricated by squeeze casting and their metallurgical and mechanical characterization has been investigated. A mixture of Ni and nano-Al 2 O 3 particles of different ratios was added to the melted Al–Si piston alloy at 700 °C and stirred under pressure. After the Al-base-nano-composites were fabricated by squeeze casting, the microstructure and the particle distribution inside the matrix have been investigated using optical and scanning electron microscopes. Moreover, the hardness and the tensile properties of the resulted Al-base-nano-composites were evaluated at room temperature by using Vickers hardness and universal tensile testers, respectively. As a result, in most cases, it was found that the matrix showed a fine eutectic structure of short silicon constituent which appeared in the form of islands in the α-phase around some added particle agglomerations of the nano-composite structures. The tendency of this structure formation increases with the increase of Ni particle addition. As the ratio of the added particles increases, the tendency of these particles to be agglomerated also increases. Regarding the tensile properties of the fabricated Al-base-nano-composites, ultimate tensile strength is increased by adding the Ni and nano-Al 2 O 3 particles up to 10 and 2 wt.%, respectively. Moreover, the ductility of the fabricated composites is significantly improved by increasing the added Ni particles. The composite material reinforced with 5 wt.% Ni and 2 wt.% nano-Al 2 O 3 particles showed superior ultimate tensile strength and good ductility compared with any other added particles in this investigation. [ABSTRACT FROM AUTHOR]

In the present paper, the Mg-11Gd-2Y-1Zn alloys with different Al addition were fabricated by the gravity permanent mold method. The effect of Al content on microstructure evolution and mechanical properties of as-cast Mg-11Gd-2Y-1Zn alloy was studied by metallographic microscope, scanning electron microscope, XRD and tensile testing. The experimental results showed that the microstructure of as-cast Mg-11Gd-2Y-1Zn alloy consisted of α-Mg phase and island-shaped Mg3 (RE, Zn) phase. When Al element was added, Al2RE phase and lamellar Mg12REZn (LPSO) phase were formed in the Mg-11Gd-2Y-1Zn alloy. With increasing Al content, LPSO phase and Mg3 (RE, Zn) phase gradually decreased, while Al2RE phase gradually increased. There were only α-Mg and Al2RE phases in the Mg-11Gd-2Y-1Zn-5Al alloy. With the increase of Al content, the grain size decreased firstly and then increased. When the Al content was 1 wt.%, the grain size of the alloy was the minimum value (28.9 μm). The ultimate tensile strength and elongation increased firstly and then decreased with increasing Al addition. And the fracture mode changed from intergranular fracture to transgranular fracture with increasing addition. When Al addition was 1 wt.%, the maximum ultimate tensile strength reached 225.6 MPa, and the elongation was 7.8%. When the content of Al element was 3 wt.%, the maximum elongation reached 10.2% and the ultimate tensile strength was 207.7 MPa. [ABSTRACT FROM AUTHOR]

To enhance the mechanical properties (e.g., strength and elongation) of the face-centered cubic (fcc) α-phase in the Au-Cu-Al system, this study focused on the introduction of the martensite phase (doubled B19 (DB19) crystal structure of Au2CuAl) via the manipulation of alloy compositions. Fundamental evaluations, such as microstructure observations, phase identifications, thermal analysis, tensile behavior examinations, and reflectance analysis, have been conducted. The presence of fcc annealing twins was observed in both the optical microscope (OM) and the scanning electron microscope (SEM) images. Both strength and elongation of the alloys were greatly promoted while the DB19 martensite phase was introduced into the alloys. Amongst all the prepared specimens, the 47Au41Cu12Al and the 44Au44Cu12Al alloys performed the optimized mechanical properties. The enhancement of strength and ductility in these two alloys was achieved while the stress plateau was observed during the tensile deformation. A plot of the ultimate tensile strength (UTS) against fracture strain was constructed to illustrate the effects of the introduction of the DB19 martensite phase on the mechanical properties of the alloys. Regardless of the manipulation of the alloy compositions and the introduction of the DB19 martensite phase, the reflectance stayed almost identical to pure Au. [ABSTRACT FROM AUTHOR]