Search

The angular log-periodic meander-line traveling wave tube (TWT) is a kind of low voltage, small-sized, high power, low cost, on chip amplifiers, and considered as a key part of the advanced communication systems, the future biomedical applications and the next electronic counter measure (ECM) instruments et al. Here, an angular log-periodic meander-line TWT is presented in this article. The angular log-periodic meander-line slow wave structure (SWS) is supported by two diamond rods. The dispersion and the impedance characteristics are analyzed in detail. In order to reduce the reflection loss, a gradual ridged waveguide is connecting the input–output standard rectangular waveguide to the meander-line SWS. The particle in cell (PIC) simulations show that the output power of the TWT can reach 55 W at 34 GHz with the operation voltage of 1800 V and the beam current of 0.2 A. The SWS is manufactured by a laser machine with Molybdenum sheet. The assembled TWT is tested and the results show that the ${S}_{{11}}$ is less than −10 dB at 30–39 GHz. The ${S}_{{21}}$ mismatch between the simulated and the measurement is discussed at the end. [ABSTRACT FROM AUTHOR]

A novel sine groove waveguide slow wave structure (SGW-SWS), originated from the sine waveguide (SW), is proposed for a wideband terahertz (THz) traveling wave tube (TWT). SGW-SWS not only has high interaction impedance in a relatively wide frequency band, but also has a wide beam tunnel. In addition, it can be fabricated using the Nano-Computer Numerical Control (CNC) milling techniques. The high-frequency simulation results show that, under the same dispersion, the passband of SGW-SWS is 23 GHz wider than that of SW-SWS, and the average interaction impedance of SGW-SWS is higher than that of SW-SWS in the whole passband. And the transverse dimension of beam tunnel is independent of the dispersion characteristics of SGW-SWS, so the beam current can be further increased by enlarging the size of beam tunnel. Moreover, the particle-in-cell (PIC) simulation results reveal that the saturated power and electronic efficiency of SGW-TWT in the frequency range of 201–260 GHz are more than 84.9 W and 2.72%, respectively, when the operating voltage is 20.8 kV and the beam current is 150 mA. [ABSTRACT FROM AUTHOR]

In this article, a novel dielectric-supported staggered dual-meander-line (DS-SDML) planar slow-wave structure (SWS) is proposed for a traveling wave tube (TWT) working at ${E}$ -band. The proposed staggered arrangement of meander-lines (MLs) leads to a stronger beam–wave interaction and achieves higher output power as compared to the symmetric arrangement. The input–output couplers have been designed by using staggered stepped double ridge waveguide, to connect the standard ${E}$ -band rectangular waveguide and the DS-SDML SWS. An attenuator and pitch tapering have been applied to the proposed SWS to suppress the unwanted frequencies and to improve the output power. Particle-in-cell (PIC) simulation results show that for an 11.8-kV, 200-mA sheet-beam, the output power can reach 283 W at 75 GHz, with a maximum gain and electronic efficiency of 34.5 dB and 11.9%, respectively. [ABSTRACT FROM AUTHOR]

The miniaturized traveling wave tube (TWT) is a kind of high-efficiency, high-power, long-lifetime power amplifier which is an attractive choice for many applications, such as outer space exploration, phased array radar detection, unmanned aerial vehicle (UAV) communication, and on-chip application. In this article, a sheet beam miniaturized TWT with V-shaped meander-line slow wave structure (SWS) supported by two trapezoidal ceramic rods is designed. First, the dispersion characteristics, the impedance characteristics, and the S-parameters of the V-shaped meander-line SWS are analyzed in detail. Then, the particle-in-cell (PIC) simulation results predict that the TWT can produce 512-W output power driven by a 7.1 kV, 0.3-A sheet beam with a rectangular cross-sectional area of 3.5 mm $\times0.1$ mm. The TWT can cover the whole ${X}$ -band when the operation voltage shift from 7.1 to 9.1 kV. At last, the V-shaped meander-line SWS is manufactured, assembled, and tested. The good agreement between the simulated and the measured ${S} _{\mathbf {11}}$ has been achieved and the mismatch between the simulated and the measured ${S} _{\mathbf {21}}$ has been discussed at the end. [ABSTRACT FROM AUTHOR]

A novel slow wave structure (SWS), named staggered double corrugated waveguide (SDCW), is proposed for the development of wideband high-power terahertz (THz) traveling wave tubes (TWTs). The SDCW-SWS not only has the wideband characteristic of staggered double grating (SDG) but also has the high interaction impedance characteristic of symmetrical double grating. In addition, its tunnel width is independent of the lower cutoff frequency and can be further increased. Numerical Eigen mode calculations show that, under the same dispersion, the passband of SDCW-SWS is increased by more than 10 GHz compared with SDG-SWS, and the average interaction impedance at 195 GHz is increased by about 62%. A particle-in-cell simulation analysis confirms that the average output power, saturated gain, and electron efficiency of SDCW-TWT at 195 GHz are ~110 W, ~20.34 dB, and ~5.46%, respectively, when the operating voltage is 20 kV and the beam current is 100 mA. Therefore, SDCW is a promising slow wave circuit of wideband high-power THz traveling wave amplifier. [ABSTRACT FROM AUTHOR]

Traveling wave tube (TWT) is an attractive solution for wideband and high-power sources or amplifiers in the terahertz (THz) band. In this article, a novel slow-wave structure (SWS) for TWT, named double tunnel sine waveguide (DTSW), which is based on sine waveguide (SW), is proposed. The following key technologies are adopted: 1) the rectangular holes, at which the operating mode is cutoff, are alternately opened on the sine-shaped ridges to form two electron beam tunnels and 2) the lower surface of rectangular holes is flush with the top of sine-shaped ridges. Compared with the SW-SWS, DTSW-SWS has the wider operating band and higher interaction impedance under the condition that the phase velocity of the two SWSs is at the same level. In addition, DTSW-SWS is simple in structure and easy to fabricate. The particle-in-cell simulation results reveal that DTSW-TWT has an output power of more than 202 W in the frequency range of 202–255 GHz with the maximum power of ~405 W and electron efficiency of ~9.8% at 215 GHz, under the operating voltage of 23 kV and beam current of 180 mA. Therefore, the DTSW should be considered as a promising SWS for the high-power and wideband THz traveling wave amplifier. [ABSTRACT FROM AUTHOR]

A large signal beam-wave interaction model for the analysis of folded waveguide traveling wave-tube (FWG TWT) is proposed. The slow-wave structure is modeled as a sequence of coupled resonant cavities. The electron beam is treated as a current source that can induce electromagnetic waves in the cavity. The beam-wave interacting process is modeled as an active matrix. Compared with the other models only calculating the in-band characteristic of FWG TWT, our model can provide characteristic analysis in both in-band and near cutoff regions, and thus broaden operating bandwidth and suppress oscillation. As verification, two FWG TWT examples were designed by using our model. Its performances predicted by our code agree well with that obtained by the experiment and particle-in-cell software, respectively. [ABSTRACT FROM AUTHOR]

In this paper, a novel small tunable periodic cusped magnet (NSTPCM) system is proposed for the purpose of realizing low voltage, big current sheet electron beam propagation in a long distance in engineering, which is composed of a series of position-fixed magnet blocks in alignment and freely sliding staggered pole pieces. This kind of NSTPCM not only generates higher magnetic field in the axial direction but also realizes more convenient adjustment of magnetic field in the transverse direction. This NSTPCM system has been successfully applied in a Ka-band sheet electron beam staggered double vane traveling wave tube. The tested sheet beam transmission efficiency is $>93$ % in a 112.7-mm-length slow-wave structure under the condition of beam voltage 24.3 kV and beam current 0.8 A. Moreover, the measured output power is $>75$ W in the range from 33 to 37.5 GHz, and the maximum output power is 128 W at 34 GHz. This paper provides the foundation for the development of sheet electron beam vacuum devices. [ABSTRACT FROM PUBLISHER]