Search

Abstract Following the experimental study and finite element (FE) model validation described in the companion paper, numerical parametric studies and the evaluation of design provisions for stainless steel channel sections under combined axial compressive load and minor axis bending moment are presented herein. The parametric studies were carried out to generate additional structural performance data over a wider range of cross-section aspect ratios and slendernesses, loading combinations and bending orientations. The test data and numerical results have been carefully analysed to develop a comprehensive understanding of the structural performance of stainless steel channel sections under combined compression and minor axis bending moment, and to assess the accuracy of the existing design provisions in Europe and North America. Comparisons of ultimate loads from the tests and FE simulations with the codified resistance predictions revealed that the current design standards typically under-estimate the capacity of stainless steel channel sections under combined compression and minor axis bending moment; this is attributed primarily to the neglect of material strain hardening and the employment of conservative interaction formulae. Improved design rules featuring more efficient interaction curves, anchored to more precise end points (i.e. cross-section resistances under pure compression and bending moment), are then proposed and presented. The new design proposals are shown to yield both more accurate and more consistent resistance predictions over the existing design provisions. Finally, statistical analyses are presented to confirm the reliability of the new design proposals according to EN 1990. Highlights • Parametric studies were carried out to generate further structural performance data. • Design provisions in EC3 and AISC were assessed against test and FE data. • New proposals were made, leading to substantial improvement in resistance prediction. • The reliability of the new proposals was confirmed according to EN 1990. [ABSTRACT FROM AUTHOR]

Repair welding for recovery from local damage of a rail head surface is known to cause high residual stress and can accelerate fatigue in the rail. This study examines repair-welded rails by applying experimental and numerical approaches. In the former approach, two newly manufactured rail specimens and four repair-welded rail specimens with two different weld depths were prepared, and their residual stresses were measured with a sectioning method. In the latter approach, a finite element repair welding simulation model was developed that adopted a prescribed temperature method with a moving block as an input heat source, and the thermal strain caused by the volume change due to solid-state phase transformation was considered. Overall, the residual stresses correlated well between the experimental and numerical approaches. The measured high compressive residual stress of −290 MPa seems to be beneficial to prevent a crack initiation in the rail surface. [ABSTRACT FROM AUTHOR]

Abstract: This work deals with the evaluation of the ultimate bending moment of a severely corroded box girder subjected to uniform vertical bending moment through a series of nonlinear finite element analysis. Two models of corrosion degradation have been adopted, one is an average general corrosion thickness reduction, and the other is the real thickness of the corroded plates. New stress–strain relations have been developed to account for the effect of corrosion on the flexural rigidity. To validate the new developed stress–strain relationships, a comparison between the finite element analysis results using the existing stress–strain models, the newly developed ones and the experimental test results of a severely corroded box girder have been conducted. The comparison showed a good agreement and supported the choice of the newly developed stress–strain relationships of corroded structures. [Copyright &y& Elsevier]

Abstract: The objective of this paper is to analyse the ultimate strength of ageing ship structures based on experimental and numerical assessments. Three experimental ultimate strength tests have been carried out on box girders under vertical bending moment and several effects have been detected due to corrosion. Extensive nonlinear finite element analyses have been performed to compare the numerical and experimental results. The ultimate bending moment of corroded box girders has been compared with existing formulas. A relationship to calculate the equivalent tangent modulus as a function of the total reduction of the cross-sectional area due to corrosion degradation has been proposed. A new stress–strain relationship has been developed, taking into account the residual stresses and the corrosion effect, which may be directly used as a master stress–strain curve for a non-linear finite element analysis. [Copyright &y& Elsevier]

Abstract: Steel caging is an effective, economical, easily applied and widely used method of strengthening RC columns. Based on the results of two experimental studies, this paper proposes the finite element modelling of RC columns strengthened by a steel cage under axial loads and bending moments. The FE models were used to obtain the N-M diagrams of experimental cases in which a study was made of the improved resistance of RC columns strengthened with this type of strengthening technique. The paper also includes a comparison of different methods of connecting the cage around the beam–column joint and a parametric study to observe the influence of diverse parameters on the behaviour of the strengthened column, including: angle dimensions, number of strips, the yield stress of the steel used in the strengthening, the dimensions of the capitals at both ends of the column, concrete strength and the characteristics of the reinforcement used in the columns. Finally, the results of the various tests (experimental and numerical) described in the paper are used to be compared with three design proposals and the goodness of fit of each one is analysed. [Copyright &y& Elsevier]

Abstract: In this research, 18 laced built-up columns with various geometric specifications were analyzed under different levels of axial load and cyclic lateral load using the finite element method. This research was performed as a continuation of the experimental investigation on the cyclic behavior of the laced columns. This study evaluated the effects of column''s geometrical parameters and various levels of axial loads on the cyclic behavior of laced columns. A compression of the results shows that there is generally good agreement between the experimental and analytical results. The analytical results showed that as the axial load increased, the ductility of the laced columns decreased significantly. Further, at high levels of axial load (i.e., loads higher than 50% of the columns'' compressive capacity), ductility was very poor. It was found that during lateral loading there is a bending moment in addition to the axial force in the lacing bars and the main chords, which affects the columns'' behavior. The slenderness ratio of the main chords between the connecters and the shape of the cross-section of the lacing bars (i.e., bending strength of the lacing bars) are the main geometrical parameters affecting the laced columns'' ductility. [Copyright &y& Elsevier]

This paper presents a study on the strength and behavior of cold-formed steel Z-sections with simple and complex stiffeners subjected to major axis bending. The study involved both experimental and numerical investigations, in which a series of specimens were examined. All specimens were failed by the combined mode of shear and moment. The results from the investigations were analyzed and compared with the combined moment and shear strengths predicted by international design rules. The suitability of the design rules in predicting the combined capacity of Z-section with complex stiffeners was assessed through a reliability analysis. [ABSTRACT FROM AUTHOR]

• H-beam welded hollow sphere developed buckling failure subjected to eccentric compression. • The design formula of H-beam welded hollow sphere subjected to eccentric compression was proposed. • The test results verified the rationality of the proposed formula. • The bearing capacity of joints is greatly affected by ribbing, H-beam height, flange width, and hollow sphere size. • The axial force–bending moment relationship curve of the joint is independent of its geometric size. An H-beam welded hollow spherical joint is a new kind of spatial grid structure. In this study, the eccentric-loaded behavior of H-beam welded hollow spherical joints was studied, and the influential law of material strength, joint size, and stiffening rib on its mechanical properties was analyzed through experimental research and numerical simulation. Parametric analyses were conducted to study the eccentric-loaded behavior of H-beam welded hollow spherical joints subjected to pure bending or the combined action of axial force and bending moment using a finite element model verified through experiments. The calculation formula of the bending bearing capacity of the joints and the axial force-bending moment curve were also obtained. Finally, the design rule for eccentric compression was proposed and verified through test results. [ABSTRACT FROM AUTHOR]

• Performance of bolted-flange connections under tension, moment and shearing. • Static tension, moment and shearing tests and FEA on bolted-flange connections. • Effect of flange thickness, bolt edge distance, flange edge width and bolt hole size. • Stiffness and strength of connections, bolt tension and contact force were obtained. • Yield bearing capacity obtained from proposed formulas agreed well with test and FEA. In this study, the square steel tube column is connected by bolted flange instead of traditional welding. For multi-rise structure, tension, bending moment, and shear force may act on the connection under vertical and horizontal loads. To investigate the mechanical behavior of flange connections, full-scale model tests and finite element analyses of 10 bolted-flange joints were carried out. The mechanical properties of the specimens and the influence of the flange thickness, flange size, and bolt hole diameter under a tension–bend–shear combination were obtained. The size of the bolt hole and flange has little effect on the load-carrying capacity of the connection. With the increase of the thickness of flange, the flexural rigidity and load-carrying capacity of the connection increase obviously, and the yield mechanism of the specimen changes from flange yield to bolt yield. The influence of the axial tension ratio on the bolt tension was investigated by the experiment-verified finite element models. The axial tension ratio is the value that the axial force of column divided by the cross-sectional area and the material design strength of the column. Increasing the axial tension ratio may increase the bolt tension, which has a harmful effect on the bolts at the tension side of the flange. Using yield line theory, formulas for calculating the static load-bearing capacity resisting the bending moment, shear and tension were deduced and verified by comparing with the result of experiment and finite element analysis. [ABSTRACT FROM AUTHOR]