Search

We introduce a novel long-range traffic monitoring system for vehicle detection, tracking, and classification based on fiber-optic distributed acoustic sensing (DAS). High resolution and long range are provided by the use of an optimized setup incorporating pulse compression, which, to our knowledge, is the first time that is applied to a traffic-monitoring DAS system. The raw data acquired with this sensor feeds an automatic vehicle detection and tracking algorithm based on a novel transformed domain that can be regarded as an evolution of the Hough Transform operating with non-binary valued signals. The detection of vehicles is performed by calculating the local maxima in the transformed domain for a given time-distance processing block of the detected signal. Then, an automatic tracking algorithm, which relies on a moving window paradigm, identifies the trajectory of the vehicle. Hence, the output of the tracking stage is a set of trajectories, each of which can be regarded as a vehicle passing event from which a vehicle signature can be extracted. This signature is unique for each vehicle, allowing us to implement a machine-learning algorithm for vehicle classification purposes. The system has been experimentally tested by performing measurements using dark fiber in a telecommunication fiber cable running in a buried conduit along 40 km of a road open to traffic. Excellent results were obtained, with a general classification rate of 97.7% for detecting vehicle passing events and 99.6% and 85.7% for specific car and truck passing events, respectively.

We demonstrate a two-wavelength differential-phase-measuring OTDR sensor that uses perfect periodic correlation phase codes to enhance the measurement performance. The two-wavelength technique extends the measurement range of OTDR sensors by synthesizing a virtual longer-wavelength measurement from two simultaneous measurements of phase using different lasers. This increases the range free from phase unwrapping errors. However, we find that the application of this technique greatly increases the relative measurement noise. To compensate for this issue, we introduce the use of optical pulse compression using perfect periodic correlation phase codes to increase the measurement signal-to-noise ratio and also to facilitate the simultaneous compensation of Rayleigh and polarization fading. In addition, we apply a method to further reduce the relative noise that is added to the two-wavelength measurement by using the synthetic wavelength measurement to unwrap the differential phase measured with a single wavelength. All this is highlighted in a 1-km sensing link in which up to 20-cm spatial resolution and 12.6 p ϵ / H z strain sensitivity are demonstrated as well as a 67-fold enhancement in measurement range compared with the use of the conventional single-wavelength method.

We demonstrate the extension of the measurement range of Brillouin optical time-domain analysis (BOTDA) sensors using a distributed Brillouin amplifier (DBA). The technique is based on injecting a DBA pump wave in the fiber to generate an additional Brillouin interaction that amplifies the BOTDA pump pulses and compensates optical fiber attenuation. This amplification does not introduce any significant noise to the BOTDA's probe wave due to the inherent directionality of the Brillouin gain. Additionally, we deploy a differential pulse-width pair measurement method to avoid measurement errors due to the interplay between the self-phase modulation effect and the changes in the temporal shape of the pulses induced by the transient behavior of Brillouin gain. Experimental proof-of-concept results in a 50-km fiber link demonstrate full compensation of the fiber's attenuation with no penalty on the signal-to-noise ratio of the detected signal.

We present a novel technique for Brillouin optical time domain analysis (BOTDA) sensors that simultaneously compensates non-local effects and reduces Brillouin noise. The technique relies on the wavelength modulation of the optical source to modify the Brillouin interaction between probe and pump waves during their propagation. The resulting Brillouin distribution mimics the wavelength modulation, creating a virtual Brillouin frequency shift profile along the sensing fiber. The fundamentals of the technique are first described theoretically and using numerical simulations. Then, proof-of-concept experiments demonstrate the capabilities of the system to reduce large variations of the pump power resulting from the interaction with high probe powers and to decrease the Brillouin induced noise enhancing the signal to noise ratio (SNR) of the system. Furthermore, we show, for the first time to our knowledge, measurements of the Brillouin distribution using an injected optical power higher than the Brillouin threshold of the fiber.

We introduce a novel phasorial differential pulse-width pair (PDPP) method for Brillouin optical time-domain analysis (BOTDA) sensors that combines spatial resolution enhancement with increased tolerance to non-local effects. It is based on the subtraction of the complex time-domain traces supplied by a sensor configuration that uses a phase-modulated probe wave and RF demodulation. The fundamentals of the technique are first described theoretically and using numerical simulation of the propagating waves. Then, proof-of-concept experiments demonstrate the measurement of the Brillouin frequency shift distribution over 50-km. The system is shown to withstand large variations of the pump power generated by its interaction with a powerful probe wave along the fiber; hence, highlighting the potential of the PDPP technique to increase the detected signal-to-noise ratio in long-range BOTDA. Moreover, the PDPP is also shown to increase the measurement contrast by allowing the use of relatively long duration pulses while retaining 1-m spatial resolution.

We demonstrate a Brillouin optical time domain analysis sensor based on a phase-modulated probe wave and RF demodulation that provides measurements tolerant to frequency-dependent variations of the pump pulse power induced by non-local effects. The tolerance to non-local effects is based on the special characteristics of the detection process, which provides an RF phase-shift signal that is largely independent of the Brillouin gain magnitude. Proof-of-concept experiments performed over a 20-km-long fiber demonstrate that the measured RF phase-shift spectrum remains unaltered for large frequency-dependent deformations of the pump pulse power. Therefore, it allows the use of a higher optical power of the probe wave, which leads to an enhancement of the detected signal to noise ratio. This can be used to extend the sensing distance, to improve the accuracy of the Brillouin frequency shift measurements, and to reduce the measurement time.

We demonstrate a novel dynamic BOTDA sensor based, for the first time to our knowledge, on the use of the Brillouin phase-shift in addition to the conventional Brillouin gain. This provides the advantage of measurements that are largely immune to variations in fiber attenuation or changes in pump pulse power. Furthermore, the optical detection deployed leads to an enhanced precision or measurement time and to the broadening of the measurement range. Proof-of-concept experiments demonstrate 1.66-kHz measurement rate with 1-m resolution over a 160 m sensing fiber length. Moreover, a measurement range of 2560 µε with a precision of 20 µε is successfully proved.

We present a novel technique to generate orthogonally polarized optical single sideband modulated signals. The modulation scheme is based on all optical stimulated Brillouin scattering processing of the optical carrier of an optical single sideband modulated signal, by means of the polarization state dragging induced by this non-linear effect. This modulation technique can be used in several microwave photonics applications, such as antenna beamforming or microwave photonics filters. In order to perform a proof-of-concept experiment, the orthogonal modulator is deployed for the implementation of an RF phase-shifter.

We propose a technique for the generation of broadband optical single sideband modulated signals. The technique is based on optically processing an optical double sideband signal using stimulated Brillouin scattering effect. An unwanted sideband suppression over 40 dB in a broadband range from 50 MHz to 20 GHz is experimentally demonstrated. In addition, we apply the generated optical single sideband signal for the spectral characterization of polarization dependent parameters of optical components. The experimental characterization of the polarization dependent loss and the differential group delay of a phase-shifted fiber Bragg grating is performed in order to demonstrate the feasibility of the technique.

We introduce a novel method for high wavelength-resolution measurement of polarization-averaged group delay, polarization dependent loss and polarization mode dispersion of optical components using swept optical single sideband modulated signals. Measurements of a phase-shifted fiber Bragg grating, a chirped fiber Bragg grating and of the Brillouin spectra of a length of fiber are used in order to demonstrate the technique.

We propose a novel scheme to implement tunable multi-tap complex coefficient filters based on optical single sideband modulation and narrow band optical filtering. A four tap filter is experimentally demonstrated to highlight the enhanced tuning performance provided by complex coefficients. Optical processing is performed by the use of a cascade of four phase-shifted fiber Bragg gratings specifically fabricated for this purpose.