Search

Tungsten-doped TiO2 thin films were prepared by sol–gel method on fluorine-doped tin oxide-coated substrates as working electrodes of dye-sensitized solar cells. The influences of different W doping (0, 2, 4, 6, and 8 at%) on the microstructure, optical, and photovoltaic properties of the W-TiO2 thin-film DSSCs were studied by the measurement of X-ray diffraction (XRD), scanning electron microscopy (SEM), X-ray photoelectron spectroscopy (XPS), Brunauer–Emmett–Teller (BET) analysis, and electrochemical impedance spectroscopy (EIS). An optimal DSSCs performance was observed with a 6 at% W-doped TiO2 thin film, resulting in a Voc of 0.68 V, a Jsc of 20.2 mA/cm2, an FF of 68.6%, and an efficiency (η) of 9.42%. The efficiency of DSSCs with 6 at% W-doped TiO2 photoanode improved by 75%. This is because the 6 at% W-doped TiO2 thin film increases the specific surface area and electron transfer rate.

Polyvinylidene fluoride (PVDF)-coated ZnO nanorod piezoelectric sensors were prepared on silicone-based polymer polydimethylsiloxane (PDMS) substrates using a hydrothermal method. The effects of catalysts (sodium hydroxide, ammonium hydroxide, and hexamethylenetetramine) on the lattice microstructure and piezoelectric properties of ZnO nanorods were analyzed. The piezoelectric properties of polyvinylidene fluoride-coated ZnO nanorods’ tactile sensors with different catalysts were measured under different forces. ZnO nanorods with hexamethylenetetramine have a high c-axis (002)-preferred orientation hexagonal wurtzite crystal structure with a maximum length of 5800 nm and an aspect ratio of 72.5. The Polyvinylidene fluoride/ZnO nanorod sensor with hexamethylenetetramine showed an excellent linear response to external pressure in the range of 0.1~1.2 N, and the best sensitivity is 61.1 mV/N.

In this study, Ba0.6Sr0.4Ti1-xMnxO3 ceramics were fabricated by a novel ball milling technique followed by spin-coating to produce thin-film resistive memories. Measurements were made using field emission scanning electron microscopes, atomic force microscopes, X-ray diffractometers, and precision power meters to observe, analyze, and calculate surface microstructures, roughness, crystalline phases, half-height widths, and memory characteristics. Firstly, the effect of different sintering methods with different substitution ratios of Mn4+ for Ti4+ was studied. The surface microstructural changes of the films prepared by the one-time sintering method were compared with those of the solid-state reaction method, and the effects of substituting a small amount of Ti4+ with Mn4+ on the physical properties were analyzed. Finally, the optimal parameters obtained in the first part of the experiment were used for the fabrication of the thin-film resistive memory devices. The voltage and current characteristics, continuous operation times, conduction mechanisms, activation energies, and hopping distances of two types of thin-film resistive memory devices, BST and BSTM, were measured and studied under different compliance currents.

In this study, the photoelectric properties of a complete series of GaS1−xSex (0 ≤ x ≤ 1) layered crystals are investigated. The photoconductivity spectra indicate a decreasing bandgap of GaS1−xSex as the Se composition x increases. Time-resolved photocurrent measurements reveal a significant improvement in the response of GaS1−xSex to light with increasing x. Frequency-dependent photocurrent measurements demonstrate that both pure GaS crystals and GaS1−xSex ternary alloy crystals exhibit a rapid decrease in photocurrents with increasing illumination frequency. Crystals with lower x exhibit a faster decrease in photocurrent. However, pure GaSe crystal maintains its photocurrent significantly even at high frequencies. Measurements for laser-power-dependent photoresponsivity and bias-voltage-dependent photoresponsivity also indicate an increase in the photoresponsivity of GaS1−xSex as x increases. Overall, the photoresponsive performance of GaS1−xSex is enhanced with increasing x, and pure GaSe exhibits the best performance. This result contradicts the findings of previous reports. Additionally, the inverse trends between bandgap and photoresponsivity with increasing x suggest that GaS1−xSex-based photodetectors could potentially offer a high response and wavelength-selectivity for UV and visible light detection. Thus, this work provides novel insights into the photoelectric characteristics of GaS1−xSex layered crystals and highlights their potential for optoelectronic applications.

Copper-doped zinc oxide films (Zn1−xCuxO) (x = 0, 2%, 4%, 6%) were fabricated on conductive substrates using the sol-gel process. The crystal structure, optical and resistive switching properties of Zn1−xCuxO films are studied and discussed. RRAM is made using Zn1−xCuxO as the resistive layer. The results show that the (002) peak intensity and grain size of Zn1−xCuxOfilms increase from 0 to 6%. In addition, PL spectroscopy shows that the oxygen vacancy defect density of Zn1−xCuxO films also increases with the increase in Cu. The improved resistive switching performance of the RRAM device can be attributed to the formation of conductive filaments and the destruction of more oxygen vacancies in the Zn1−xCuxO film. Consequently, the RRAM device exhibits a higher low resistance state to high resistance state ratio and an HRS state of higher resistance value.

Activation energy, bipolar resistance switching behavior, and the electrical conduction transport properties of ITOX:SiO2 thin film resistive random access memory (RRAM) devices were observed and discussed. The ITOX:SiO2 thin films were prepared using a co-sputtering deposition method on the TiN/Si substrate. For the RRAM device structure fabrication, an Al/ITOX:SiO2/TiN/Si structure was prepared by using aluminum for the top electrode and a TiN material for the bottom electrode. In addition, grain growth, defect reduction, and RRAM device performance of the ITOX:SiO2 thin film for the various oxygen gas flow conditions were observed and described. Based on the I-V curve measurements of the RRAM devices, the turn on-off ratio and the bipolar resistance switching properties of the Al/ITOX:SiO2/TiN/Si RRAM devices in the set and reset states were also obtained. At low operating voltages and high resistance values, the conductance mechanism exhibits hopping conduction mechanisms for set states. Moreover, at high operating voltages, the conductance mechanism behaves as an ohmic conduction current mechanism. Finally, the Al/ITOX:SiO2/TiN/Si RRAM devices demonstrated memory window properties, bipolar resistance switching behavior, and nonvolatile characteristics for next-generation nonvolatile memory applications.

By a sol–gel method, a BiFeO3 (BFO) capacitor is fabricated and connected with the control thin film transistor (TFT). Compared with a control thin-film transistor, the proposed BFO TFT achieves 56% drive current enhancement and 7–28% subthreshold swing (SS) reduction. Moreover, the effect of the proposed BiFeO3 capacitor on IDS-VGS hysteresis in the BFO TFT is 0.1–0.2 V. Because dVint/dVGS > 1 is obtained at a wide range of VGS, it reveals that the incomplete dipole flipping is a major mechanism to obtain improved SS and a small hysteresis effect in the BFO TFT. Experimental results indicate that sol-gel BFO TFT is a potential candidate for digital application.

Bi1-xMgxFeO3 (BMFO, x = 0, 0.02, 0.04, 0.06 and 0.08) multiferroic films were directly synthesized on flexible stainless steel (FSS), save the bottom electrode process, by means of sol–gel spin-coating technology. The effects of different bending conditions on ferroelectric, dielectric and leakage-current properties of BMFO films were investigated. The leakage-current densities of BiFeO3 (BFO, x = 0) and BMFO (x = 0.06) films were 5.86 × 10−4 and 3.73 × 10−7 A/cm2, which shows that the BMFO (x = 0.06) has more than three orders of magnitude lower than that of BFO film. The residual polarization (2 Pr) can be enhanced from 120 to 140 μC/cm2. The proper doping of Mg in BiFeO3 film could provide an effective method for reducing the leakage-current values as well as boosting the ferroelectric properties. In this study, the leakage-current mechanism of low electric field and high electric field of BMFO film is analyzed and established. In addition, the flexible BMFO film maintains practical ferroelectric and leakage-current properties at retention time of 106 s under different symmetry bending conditions. These results indicate that the BFMO film will be very practical in opto-electronic and storage device applications.

Zn1−xMgxO (x = 0, 0.03, 0.05, and 0.07) nanocrystalline films were grown on silicon substrates using the sol–gel method. Furthermore, Zn1−xMgxO vertically aligned hexagonal symmetrical nanorods with six reflection symmetries were fabricated on pure ZnO-seeded layer n-type silicon substrates via a low-temperature hydrothermal method to enhance the ultraviolet (UV) light response. The crystal microstructures and surface morphologies of nanocrystalline films and nanorod arrays were determined by X-ray diffraction (XRD) and field emission scanning electron microscopy (FE-SEM). Transmission spectra showed that the increasing Mg content will increase the band gap energy from 3.28 to 3.46 eV. However, the current–voltage curves in the dark and under UV illumination showed that the UV response did not improve by the incorporation of magnesium. We changed the flat surface of films into symmetrical nanorod arrays and demonstrated they can significantly enhance the normalized photo-to-dark-current ratio up to ten times.

Stannous oxide (SnO) nanowires were synthesized by a template and catalyst-free thermal oxidation process. After annealing a Sn nanowires-embedded anodic aluminum oxide (AAO) template in air, we obtained a large amount of SnO nanowires. SnO nanowires were first prepared by electrochemical deposition and an oxidization method based on an AAO template. The preparation of SnO nanowires used aluminum sheet (purity 99.999%) and then a two-step anodization procedure to obtain a raw alumina mold. Finally, transparent alumina molds (AAO template) were obtained by reaming, soaking with phosphoric acid for 20 min, and a stripping process. We got a pore size of < 20 nm on the transparent alumina mold. In order to meet electroplating needs, we produced a platinum film on the bottom surface of the AAO template by using a sputtering method as the electrode of electroplating deposition. The structure was characterized by X-ray diffraction (XRD). High resolution transmission electron microscopy (HRTEM) and field emission scanning electron microscopy (FESEM) with X-ray energy dispersive spectrometer (EDS) were used to observe the morphology. The EDS spectrum showed that components of the materials were Sn and O. FE-SEM results showed the synthesized SnO nanowires have an approximate length of ~10−20 μm with a highly aspect ratio of > 500. SnO nanowires with a Sn/O atomic ratio of ~1:1 were observed from EDS. The crystal structure of SnO nanowires showed that all the peaks within the spectrum lead to SnO with a tetragonal structure. This study may lead to the use of the 1D structure nanowires into electronic nanodevices and/or sensors, thus leading to nano-based functional structures.

GaAs p-i-n solar cells are studied using electroreflectance (ER) spectroscopy, light beam induced current (LBIC) mapping and photovoltaic characterization. Using ER measurements, the electric field across the pn junction of a wafer can be evaluated, showing 167 kV/cm and 275 kV/cm in the built-in condition and at −3 V reverse bias, respectively. In order to understand the effect of the interval between metal grids on the device’s solar performance, we performed LBIC mapping and solar illumination on samples of different grid spacings. We found that the integrated photocurrent intensity of LBIC mapping shows a consistent trend with the solar performance of the devices with various metal grid spacings. For the wafer used in this study, the optimal grid spacing was found to be around 300 μm. Our results clearly show the importance of the metal grid pattern in achieving high-efficiency solar cells.

Bipolar resistive switching properties and endurance switching behavior of the neodymium oxide (Nd2O3) thin films resistive random access memory (RRAM) devices for a high resistive status/low resistive status (HRS/LRS) using a low temperature supercritical carbon dioxide fluid (SCF) improvement post-treatment process were investigated. Electrical and physical properties improvement of Nd2O3 thin films were measured by X-ray diffraction (XRD), scanning electron microscopy (SEM), X-ray photoelectron spectroscopy (XPS) and current versus voltage (I-V) measurement. The metal-like behavior of ohmic conduction mechanism and metallic cluster reaction of hopping conduction mechanism in initial metallic filament path forming process of the SCF-treated thin films RRAM devices was assumed and discussed. Finally, the electrical conduction mechanism of the thin films RRAM derives for set/reset was also discussed and verified in filament path physical model. [ABSTRACT FROM AUTHOR]

The novel pyroelectric IR detectors have been fabricated using the Polyvinylidene Fluoride (PVDF)/Lead Titanate (PT) pyroelectric bilayer thin films, which were deposited onto Pt(111)/SiO[sub 2]/Si(100) substrates by a sol-gel process. The ceramic/polymer structure was constructed of the randomly oriented polycrystalline PT film (∼1 µm) heated at 700°C for 1 h and the β-phase PVDF film crystallized at 65°C for 2 h. The effects of PVDF thin film thickness (100 ∼ 580 nm) on the pyroelectric response of IR detectors were studied. The results show that the depositions of PVDF thin films onto the PT films will cause the leakage current (J) of the detectors decrease from 6.37 × 10[sup -7] A/cm² to 3.86 × 10[sup -7] A/cm². The specific detectivity (D[sup *]) measured at 100 Hz decreased from 2.72 × 10[sup 7] cm. Hz[sup ½]/W for detector without PVDF to 1.71 × 10[sup 7] cm. Hz[sup ½]/W for detector with PVDF thickness of 580 nm. By optimizing the ratio of the specific detectivity (D[sup *]) to leakage current, D[sup *]/J, the detector with PVDF thickness of 295 nm exhibits the best performance. [ABSTRACT FROM AUTHOR]