Search

Introduction. Recently, photovoltaic (PV) systems are increasingly favored for converting solar energy into electricity. PV power systems have successfully evolved from small, standalone installations to large-scale, grid-connected systems. When the nonlinear loads are connected to a grid-tied PV system, the power quality can deteriorate due to the active power supplied by the PV array, there’s a noticeable decline in the quality of power delivered to consumers. Its combination with the shunt active power filter (SAPF) enhances system efficiency. Consequently, this integrated system is adept at not only powering local loads but also at compensating for reactive power and filtering out harmonic currents from the main grid. The novelty of the work describes how an operation of a small scale PV system connected to the low voltage distribution system, and nonlinear load can be achieved, the investigation aims to analyze the system’s behavior and elucidate the advantages of employing various control algorithms. These proposed algorithms are designed to ensure a unity power factor for the utility grid while prioritizing high convergence speed and robustness against load power fluctuations across different levels of solar irradiation affecting the PV modules. The purpose of this work is to enhance the dynamic performance of the SAPF by cooperatively using a self-tuning filter (STF) based instantaneous active and reactive power method (PQ) with a novel predictive current control, enhance the system resilience, ensure optimal management of the total active power between the PV system, the electrical network and the non-linear load by integrating the functionalities of the SAPF under different levels of solar irradiation and maintain the DC-link capacitor voltage constant. Methods. A novel predictive current controller is designed to generate the switching signals piloted the three phase source voltage inverter, also a novel algorithm of instantaneous active and reactive power is developed, based on STF, to extract accurately the harmonic reference under non ideal grid voltage, also the perturb and observe algorithm is used to extract, under step change of solar irradiation, the maximum power point tracking of the PV module and the PI controller is used to maintain constant the DC-link capacitor voltage of the SAPF. Results. The efficacy of the proposed system is primarily centered on the grid side, and the performance evaluation of the control system is conducted using the STF based PQ algorithm and predictive current control. In addition, comprehensive testing encompasses all modes of operation, including scenarios involving distorted voltage sources, step changes in solar radiation, and variations in nonlinear loads. Results highlight superior performance in both transient and stable states, affirming the robustness and effectiveness of the proposed controllers. Practical value. The total harmonic distortion value of the grid current for all tests respects the IEEE Standard 519-1992. [ABSTRACT FROM AUTHOR]

Optimization algorithms are essential tools used to address real-world problems through minimization or maximization processes. In the context of photovoltaic (PV) systems, various optimization algorithms have been employed to extract solar cell parameters using minimization techniques, and to identify the maximum power point (MPP) using maximization approaches. However, under partial shading conditions or during rapidly changing irradiance, many of these algorithms tend to get trapped in local minima, failing to locate the global maximum power point (GMPPT). This shortcoming leads to significant energy losses from PV cells. Similarly, the extraction of solar cell parameters is often compromised by the random search behavior and inadequate exploration and exploitation capabilities of many existing algorithms. The Jellyfish Search Optimization (JSO) algorithm is a recent, parameter-free method developed to tackle a wide range of optimization problems. Despite its innovative design, JSO is prone to premature convergence and exhibits a longer convergence time. To address these limitations, this paper proposes a modified version of the JSO algorithm, which integrates the state-of-the-art features of JSO with the Lévy flight characteristic from the cuckoo search algorithm. This combination aims to achieve a better balance between exploration and exploitation. To validate the effectiveness of the proposed Improved Jellyfish Search Optimization (IJSO) algorithm in PV systems, extensive experiments were conducted. These experiments included benchmarking with complex test functions, extracting cell parameters using various solar cell models, and maximizing energy output from PV systems under different environmental conditions. The results demonstrate that the proposed IJSO algorithm effectively enhances parameter extraction and global maximum power point tracking, making it a promising solution for optimizing energy extraction from PV cells in dynamic conditions. [ABSTRACT FROM AUTHOR]

The high inductance current ripple and the PV voltage fluctuations limitation at the DC (direct current) -DC link have been the unsolved problems in the photovoltaic systems tied in grid. A control strategy with a current hysteresis loop is proposed to address the issues of high inductance current ripple in photovoltaic systems which can achieve real-time duty cycle regulation. Differing from the conventional mode that uses one switch in the buck-boost DC-DC link, two switches have been designed here to separate the buck and boost modes for the coordinated control, which can achieve a wide PV voltage fluctuations range. Based on the conventional fixed-duty cycle determination method, a real-time duty cycle determination method is proposed by introducing changes in inductance current. In order to improve power conversion efficiency, the incremental conductance method is improved by introducing the steepest gradient descent to quickly achieve the maximum power point tracking. This study experimentally verifies the proposed current hysteresis coordinated control method, effectively suppressing the ripple of the inductor current and expand the PV voltage fluctuation in the DC-DC link on the basis of maintaining power conversion efficiency as much as possible. [ABSTRACT FROM AUTHOR]

The traditional short circuit ratio index does not consider the impact of energy storage devices (ESDs) and cannot be used for the collaborative optimization of ESDs and renewable energy sources (RESs). Therefore, this paper proposes a novel synergistic capacity short circuit ratio (SCSCR) index, which can reflect the interaction between multiple RESs and ESDs on each bus under different capacities. Based on the proposed SCSCR, a coordinated optimization method of RESs and ESDs is proposed. It ensures system strength while determining the optimal location and capacity proportion of RESs and ESDs. Firstly, the location and capacity proportion of RESs are obtained through optimization method because the system strength is mainly determined by RESs connection points. Secondly, the optimal location and capacity proportion of the ESDs are found under the optimal configuration of the RESs. The proposed optimization method ensures the system strength while obtaining the optimal location and optimal capacity proportion of RESs and ESDs. Finally, the simulation results verify the effectiveness of this method on the IEEE 9 bus and 39 bus systems, providing reference for the site selection and efficient operation of RESs and ESDs. [ABSTRACT FROM AUTHOR]

The variable pressure source system is widely used in renewable energy recovery scenarios. However, the instability of the new energy input and the nonlinearity of the power generation system can lead to problems such as more difficult tracking and control of the maximum power point and poor power generation quality. To address the problem of lower efficiency under varying inputs, which is prevalent in renewable energy generation, this paper establishes an energy recovery system model based on power conversion rectifier topology, designs a speed current double closed‐loop control strategy, proposes an online variable‐step maximum efficiency point tracking method based on experience curves, and tests the overall energy recovery effect through system simulation and comparative experiments. The simulation results show that the maximum efficiency point tracking method proposed in this paper reduces the number of optimization searches by 50% and improves optimization speed. The experiment results show that, under the drastic changes of the input, the method proposed in this paper could reduce the total harmonic distortion to 5.65%, improve the energy recovery efficiency by 10.976%, and reduce the fluctuation ratio of the voltage to 2.43%. This study can provide an important reference for the collection and utilization of new energy sources. [ABSTRACT FROM AUTHOR]

This paper presents an innovative scheme to enhance the efficiency of power extraction from wind energy conversion systems (WECSs) under random loads. The study investigates how stochastic load consumption, modeled and predicted using a Markov chain process, impacts WECS efficiency. The suggested approach regulates the rectifier voltage rather than the rotor speed, making it a sensorless and reliable method for small-scale WECSs. Nonlinear WECS dynamics are represented using Takagi–Sugeno (TS) fuzzy modeling. Furthermore, the closed-loop system's stochastic stability and recursive feasibility are guaranteed regardless of random load changes. The performance of the suggested controller is compared with the traditional perturb-and-observe (P&O) algorithm under varying wind speeds and random load variations. Simulation results show that the proposed approach outperforms the traditional P&O algorithm, demonstrating higher tracking efficiency, rapid convergence to the maximum power point (MPP), reduced steady-state oscillations, and lower error indices. Enhancing WECS efficiency under unpredictable load conditions is the primary contribution, with simulation results indicating that the tracking efficiency increases to  99.93 % . [ABSTRACT FROM AUTHOR]

Photovoltaic power generation systems mainly use the maximum power tracking (MPPT) controller to adjust the voltage and current of the solar cells in the photovoltaic array, so that the photovoltaic array runs at the maximum power point (MPP) to achieve the purpose of maximum power output. At present, photovoltaic power stations mainly adopt the traditional method to track the maximum power point, but this fixed step method easily causes output power oscillation of the photovoltaic array when tracking the maximum power point, and it easily falls into the local extreme point under partial shadow conditions. In order to solve these problems, this paper proposes an improved perturbation observation method and backstepping method (IP&O-backstepping) to replace the traditional method applied to the MPPT controller to optimize the operating state of the solar cell, thereby improving the output power point of the photovoltaic array and increasing the output power of the photovoltaic array. The algorithm first uses the improved perturbation and observation (IP&O) method to search the maximum power point of the photovoltaic array and output the reference voltage. Secondly, the reference voltage is input into the backstepping algorithm for voltage tracking. Finally, the algorithm tracks the reference voltage and makes the photovoltaic array operate at the maximum power point. The simulation is carried out by using MATLAB/Simulink. The IP&O-backstepping algorithm is compared with the intelligent algorithm and the traditional method, and the results show that compared to the above algorithm, the IP&O-backstepping algorithm can not only track the maximum power point of the photovoltaic array, but also has a faster tracking speed, and the output power has almost no oscillation when the photovoltaic array runs at the maximum power point. [ABSTRACT FROM AUTHOR]

Based on the characteristics of the whale optimization algorithm (WOA) and perturbation observation (P&O) method, this paper proposes a novel hybrid approach called the improved chaotic whale optimization combined with perturb and observe (ICWOA-P&O) method for maximum power point tracking (MPPT) control to solve the challenge of low efficiency in photovoltaic (PV) power generation under local shadows. First, the ICWOA is used for a global search to quickly locate the position of the maximum power point (MPP). Then, the P&O method is used for a fine-grained local search to quickly track the position of the global maximum power point (GMPP) with low oscillation. To ensure accuracy, the tracking performance of the ICWOA-P&O method is comprehensively compared with the WOA-P&O, WOA, and PSO models under four conditions: uniform irradiance, static local shading, dynamic shading, and sudden changes in irradiance and temperature. The simulation results verify that under the above four conditions, the ICWOA-P&O method can track the MPP continuously and stably and greatly improves the convergence time and accuracy. Compared with the other three methods, the ICWOA-P&O method can effectively obtain the fastest tracking speed (less than 0.1 s), the highest tracking accuracy (more than 99.97%), the smallest relative error (less than 0.03%), and the smallest oscillation fluctuation. Finally, this study integrated the ICWOA-P&O algorithm into the designed MPPT controller hardware and established a practical PV experimental platform based on the ICWOA-P&O control algorithm for practical tests. [ABSTRACT FROM AUTHOR]

Due to the increasing energy demand, traditional fossil fuels are gradually decaying day by day as analyzed by many researchers. Fossil fuels are not sufficient to fulfil the requirement of energy demand and it also produces greenhouse gas emissions. In this regard, worldwide research is going on related to renewable energy sources (RESs) like solar photovoltaic (SPV), wind turbines, fuel cells etc. The source of SPV is plentiful and environment friendly which converts solar radiation to non-linear electrical power. This power is not suitable for a stable system. Therefore, the maximum power point tracking (MPPT) controller is required to find the optimum maximum power point (MPP) to the load. The MPPT technology regulates the duty-cycle in favour of the DC-DC converter to continuously obtain maximum power from the SPV arrays. In the past few decades, the learning of MPPT techniques has made substantial progress in the RESs. This research article analyzes the performance of various MPPT techniques in the proposed SPV framework. The main investigation is to assess different MPPT techniques to optimize power from the SPV framework. The artificial neural network (ANN)-MPPT method has been observed to be more effective in output power production and transient response about the MPP than conventional perturb and observe (P&O)-MPPT and fuzzy logic controller (FLC)-MPPT technology. [ABSTRACT FROM AUTHOR]

Programmable matter refers to material that can be programmed to alter its physical properties, including its shape. Such matter can be built as a lattice of attached robotic modules, each seen as an autonomous agent with communication and motion capabilities. Self-reconfiguration consists in changing the initial arrangement of modules to form a desired goal shape, and is known to be a complex problem due to its algorithmic complexity and motion constraints. In this paper, we propose to use a max-flow algorithm as a centralized global planner to determine the concurrent paths to be traversed by modules through a porous structure composed of 3D Catoms meta-modules with the aim of increasing the parallelism of motions, and hence decreasing the self-reconfiguration time. We implement a traffic light system as a distributed asynchronous local planning algorithm to control the motions to avoid collisions. We evaluated our algorithm using VisibleSim simulator on different self-reconfiguration scenarios and compared the performance with an existing fully distributed synchronous self-reconfiguration algorithm for similar structures. The results show that the new method provides a significant gain in self-reconfiguration time and energy efficiency. [ABSTRACT FROM AUTHOR]

The efficiency of standalone photovoltaic (PV) systems heavily relies on the effectiveness of their maximum power point tracking (MPPT) controller. This study aims to improve the operational efficiency and reliability of standalone PV systems by introducing a novel control scheme, the Immersion and Invariance Neural Network (II-NN). This innovative system integrates a nonlinear estimator of solar irradiance with a neural network (NN) model, eliminating the need for direct irradiance measurements and associated costly sensors. The proposed methodology uses the Immersion and Invariance algorithm to design a nonlinear estimator that leverages the real-time measurements of PV current and voltage to estimate the incident irradiance. The NN then processes this estimated irradiance to determine the MPP voltage accurately. A robust nonlinear controller ensures the PV system operates at the MPP. This approach stands out by managing the nonlinearities, parametric uncertainties, and dynamic variations in PV systems without relying on direct irradiance measurements. The II-NN system was rigorously tested and validated under real climatic conditions, providing a realistic performance assessment. The principal results show that the II-NN system achieves a mean error of 0.0183V and a mean absolute percentage error of 0.3913%, with an overall MPPT efficiency of up to 99.84%. Comparisons with the existing methods, including perturb and observe, incremental conductance, and three other recent algorithms, reveal that the II-NN system outperforms these alternatives. The major conclusion is that the II-NN algorithm significantly enhances the operational efficiency of PV systems while simplifying their implementation, making them more cost-effective and accessible. This study substantially contributes to PV system control by advancing a robust, intelligent, and sensorless MPPT control scheme that maintains high performance even under varying and unpredictable climatic conditions. [ABSTRACT FROM AUTHOR]

This work presents a system design for extracting maximum power using the modified maximum power point tracking (MPPT) technique and a novel high-gain DC-DC converter, which was then used to supply a microgrid system with a conventional buck converter. We present a novel structure comprising the MPPT, voltage boosting, and voltage regulating components for a DC microgrid in a single system. The most important features of a photovoltaic (PV) system include a high-gain converter and maximum PV power extraction; considering these, we present a high-gain DC-DC converter that boosts the output voltage to ten times the input voltage. Furthermore, the MPPT technique extracts maximum power from the PV panel based on model predictive control through its better transient response than the conventional incremental conductance method. The MPPT approach was tested with both fixed-and variable-step operations, and the results were compared for load variations. Considering the economics of the system, the proposed approach attempts cost reduction by optimizing the number of sensors to two instead of three. Simulations were conducted under different environmental conditions using MATLAB-Simulink, and the performance differences between the conventional incremental conductance and proposed MPPT-based methods are shown. Next, DC voltage regulation was implemented for the proposed PV and existing systems by considering different load and irradiation conditions while maintaining constant temperature. The simulation results showed the latter system had better performance than the former under different environmental conditions, with persistent results for voltage regulation at different load and irradiation conditions. [ABSTRACT FROM AUTHOR]

A power processing system (PPS) with a seven‐level dual‐buck inverter (SLDBI) for a photovoltaic (PV) power generation system is proposed. The PPS is comprised of a boost power converter and an SLDBI. The boost power converter matches the voltage of the PV array with that of the SLDBI and functions as the maximum power point tracker for the PV array. The SLDBI consists of a dual‐buck bridge converter (DBBC) and a three‐level DC converter (TLDC). The DBBC effectively reduces leakage current in the PPS and prevents current from flowing through the parallel body diode of the power switches, allowing the use of MOSFETs as power electronic switches to enhance power efficiency. The TLDC is structured as a semi‐controlled full‐bridge system to generate a three‐level DC voltage. Besides, the DBBC and TLDC produce a seven‐level AC voltage and drive a sinusoidal current to the utility. The SLDBI reduces both the filter inductor size and the switching loss of power switches. With only six power switches, it simplifies the power circuit. A hardware prototype has been built to experimentally verify the proposed PPS. [ABSTRACT FROM AUTHOR]

This article presents the contribution of multicellular converters in improving of the quality of power produced in photovoltaic chain, with the aim of exploiting the maximum power produced by the photovoltaic generator with low oscillations around of the maximum power point (MPP) at steady state and to reduce switching losses. After modeling the multicellular parallel boost converter, fractional short circuit current (FSCC) MPPT was modified to get an estimated photocurrent as a reference to control the inductance current for good functioning of the converter in pursuit of the maximum power point. To verify the performance of the proposed solution, the system was submitted to irradiance and temperature variations. The simulations carried out in the Matlab/Simulink environment presented satisfactory results of the proposed solution, in comparison with the high-gain quadratic boost converter we have a response time of 0.04 s, power oscillations at maximum point around 0.05 W and efficiency of 99.08%; in comparison with the interleaved high-gain boost converter the results show a response time of 0.1 s for the transferred power, a very low output voltage ripples of 0.001% and 98.37% as efficiency of the chain. The proposed solution can be connected to a grid with a reduction of level of the inverter and active filter. [ABSTRACT FROM AUTHOR]

Partial shading of Photovoltaic (PV) system is commonly observed in outdoor field conditions specially in the Road- Integrated Photovoltaic systems. The non-uniform illumination causes mismatch in the electrical output between the cells, which results in an instantaneous effect on power generated and a long-term effect on reliability, it also causes hotspot issues. The objective of this work is to study the partial shading effect on the Road-Integrated PV (RIPV) cells and the soiling model effect under the active and inactive states of Multilevel Bypass (MLB) diodes. In this work, an electrical Simulation Program with Integrated Circuit Emphasis (Ng-SPICE) simulation model has been developed using irradiance model data. This data was collected using a Digital Elevation Model (DEM) called Light Resolution Light detection and Ranging (LidAR). The model was simulated using the Simple Sky Dome Projector (SSDP) software to analyze the impact of different shading conditions and study the effect of MLB diodes on the partial shading RIPV modules and the effect of MLB diodes in the soiling model. [ABSTRACT FROM AUTHOR]

Maximum power point tracking (MPPT) algorithms are commonly used in photovoltaic (PV) systems to optimize the power output from the solar panels. Among the various MPPT algorithms, the perturb and observe (P&O) algorithm is a popular choice due to its simplicity and effectiveness. However, the basic P&O algorithm has some limitations, such as oscillations and steadystate error under rapidly changing irradiance conditions. The enhanced algorithm includes a modified perturbation step and a dynamic step size adjustment scheme. This reduces the oscillations and improves the tracking accuracy. In the dynamic step size adjustment scheme, the step size is adjusted based on the rate of change of the PV output power. This improves the tracking performance under rapidly changing irradiance conditions. In order to prove the performance of the designed control algorithm, we will test it under simple climatic conditions of fixed temperature (30°C) and variable irradiation in the form of steps (500W/m2 and 2000w/m2) and see the system response. The performance of the enhanced P&O algorithm has been evaluated using MATLAB simulations. [ABSTRACT FROM AUTHOR]

This study presents the design and implementation of an efficient off-grid photovoltaic (PV)-powered motor-pump system utilizing a two-stage power converter. The system integrates a neural network-based maximum power point tracking (MPPT-NN) algorithm with a proportional integral (PI) controller and an additional bidirectional PI charger. Controller gains are optimized using ant colony optimization (ACO) to achieve optimal performance. The proposed MPPT-NN-PI/ACO controller enhances control responses and improves energy utilization efficiency by 17% compared to traditional PI controller. Performance comparisons of MPPT techniques demonstrates that the proposed controller outperforms several existing methods, including commercial on-off controllers, the modified Perturb & Observe algorithm, and neural network-based controllers, by approximately 4%-20%. It shows a slightly different performance of about 1%-6% compared to advanced adaptive controllers, including fuzzy logic and neuro-fuzzy controllers. For bidirectional charger performance, the DC bus voltage connecting the boost converter and bidirectional converter remains stable with small ripples and is well-aligned with the reference voltage, ensuring uninterrupted operation under varying weather conditions. The bidirectional charge management effectively maintains battery state-of-charge (SOC), showing a decline during periods of insufficient PV energy and achieving full charging during periods of excess PV energy. System performance is validated through both simulation and laboratory-scale prototyping, ensuring robust operation. [ABSTRACT FROM AUTHOR]

Owing to the effect of temperature on the maximum power point of photovoltaic modules, the anticipated benefits of maximum power point tracking charge controller are also greatly affected under high-temperature environments. This paper presents experimental study results based on the investigations of the effect of high cell temperatues on the performance of maximum power point tracking charge controllers. The study was carried out over three months at Kenyatta University in Nairobi, Kenya under moderate and high temperature conditions. The experiments are carried out using two market-ready maximum power point tracking charge controllers and a normal pulse-width modulation charge controller as the reference. The study establishes that below 50 °C, the maximum power point tracking charge controller exhibits significant advantages over its counterpart with about 24% - 29%, additional energy gain. However, at high cell temperatures, the maximum power point tracking charge controller loses its added advantage over the pulse-width modulation charge controller and its performance benefits drop from an average of 28% to 0.2%. This demonstrates that an ordinary pulse-width modulation charge controller would achieve the same yields under high-temperature conditions and at an even lower premium. [ABSTRACT FROM AUTHOR]

Solar water pumps are crucial for farmers, significantly reducing energy costs and providing independence from conventional fuels. Their adoption is further incentivized by government subsidies, making them a practical choice that aligns with sustainable agricultural practices. However, the cost of the required solar panels for the chosen power makes it essential to optimize solar water pumping systems (SWPS) for economic viability. This study enhances the efficiency and reliability of permanent magnet synchronous motor (PMSM)-driven SWPS in rural areas using hybrid maximum power point tracking (MPPT) algorithms and voltage-to-frequency (V/f) control strategy. It investigates the sensorless scalar control method for PMSM-based water pumps and evaluates various MPPT algorithms, including grey wolf optimization (GWO), particle swarm optimization (PSO), perturb and observe (PO), and incremental conductance (INC), along with hybrid combinations. The study, conducted using MATLAB Simulink, assesses these algorithms on convergence time, MPPT accuracy, torque ripple, and system efficiency under different partial shading conditions. Findings reveal that INC-GWO excels, providing higher accuracy, faster convergence, and reduced steady-state oscillations, thus boosting system efficiency. The V/f control strategy simplifies control mechanisms and enhances performance. Considering system non-idealities and maximum duty cycle limitations, PMSM-based SWPS achieve superior efficiency and stability, making them viable for off-grid water pumping applications. [ABSTRACT FROM AUTHOR]

Abstract Solar photovoltaic energy is a vital renewable resource because it is clean, endless, and pollution‐free. Due to the fast growth of the semiconductor and power electronics sectors, photovoltaic (PV) technologies are climbing significant attention in modern electrical power applications. Operating PV energy conversion systems at the maximum power point is essential for getting the maximum power output and raising efficiency. This paper proposes a regression‐based Perturb and Observe method to quickly find a global maximum power point, avoiding being stuck in local maxima, likewise analytical and metaheuristic methods. The improved control focuses on the narrowed search areas by linear and non‐linear regression analyses using the generated PV model on a flexible Python environment. Furthermore, the method's accuracy is validated in real time under variable temperatures, irradiations, and loads. This method was proven with a hardware implementation. The proposed method is more than 98% accurate and can withstand long‐term modelling. The suggested regression‐based perturbation and observation method provided a short learning time and easy implementation. Additionally, the dynamic recorded results can be visualized for researchers to utilize efficiently.

This paper compares different maximum power point tracking (MPPT) control strategies in microgrid dynamics, focussing on perturb and observe (P&O), adaptive neuro-fuzzy inference system (ANFIS), particle swarm optimisation (PSO), and PSO sliding mode controller techniques. The study investigates their performance under varying microgrid conditions, considering factors like weather and load variations. The simulation results provide a detailed comparative analysis of the power at the point of common coupling (PCC) for MPPT techniques at different time intervals. Both the P&O and PSO sliding mode recorded a power output of 287 kW, while PSO-ANFIS achieved a slightly higher power output of 294 kW. At 2.5 seconds, the P&O method recorded a power output of 712 kW, while the PSO sliding mode and the PSO-ANFIS techniques achieved 717 kW and 738 kW, respectively. Overall, the PSO-ANFIS technique consistently outperformed the other methods in terms of power output, demonstrating its effectiveness in maximising energy extraction and adaptability to dynamic conditions. These findings provide valuable insights for designing and implementing MPPT controllers in microgrid systems, emphasising the efficiency of the hybrid PSO-ANFIS technique in enhancing the overall performance and stability of renewable energy systems.

In this research work, three maximum power point tracking (MPPT) control algorithms based on power feedback are applied to two types of converters, namely Zeta and buck-boost, in the photovoltaic (PV) system. The PV system is intended to guarantee the power supply to a remote smart greenhouse. The control algorithms investigated are perturb and observe (P&O), incremental conductance (IncCond), and fuzzy logic (FLC) methods. Their performance are investigated and compared for each converter. It is found that the maximum power is always achieved, even during abrupt changes in irradiation or/and in temperature. The three methods have shown to have good performance; fast response time and very low steady-state error, with minor preference of the P&O method where the output voltage followed the input with high efficiency. The comparative study revealed that the power response time of the PV generator under stable conditions (constant irradiance and constant temperature) for P&O and IncCond was longer in the buck-boost converter than in the Zeta. On the other hand, the ripple level was better for the buck-boost. For the FLC, the maximum power was reached in a shorter time (short response time) with the smallest ripple. As for operation under variable environmental conditions, the Zeta outperformed the buck-boost for each control technique.

In practical engineering applications, factors like dust adhesion and environmental changes can cause photovoltaic arrays to exhibit multiple peaks in output power. An optimization algorithm with global optimization capability is needed to track its maximum power. In this regard, this paper proposes an improved marine predator algorithm (IMPA) to extract the maximum power point of photovoltaic system under complex solar irradiation conditions. To overcome the issues in the traditional marine predator algorithm (MPA), the opposition-based learning(OBL) strategy is introduced in IMPA, and the sine cosine algorithm (SCA) is integrated into the iteration stage to enhance the search ability of the algorithm. Furthermore, the low-order converter in the traditional MPPT control system is replaced by the Zeta converter, which increases the operating voltage range. Ultimately, simulation results demonstrate that the MPPT based on IMPA has higher tracking efficiency and shorter response time.The experimental results also indicate the practical feasibility of this method, as well as its high level of stability and robustness. [ABSTRACT FROM AUTHOR]

Now, the present power generation and distribution companies are working on renewable energy systems because their features are low-level atmospheric pollution, producing less greenhouse pollutants, more reliability, good static performance, and high robustness. In this work, the sunlight Photovoltaic (PV) system is selected because of its advantages are easily available in the atmosphere, high flexibility, zero carbon footprint, easy to maintain, and less transportation cost. However, solar networks produce nonlinear I-V characteristics. Due to the non-linear nature of the solar system, the extraction of peak voltage from the PV module is a very tough task. So, in this article, a variable modified step grey wolf method is integrated with the adaptive-neuro-fuzzy-inference-system to improve the energy production of solar systems. The features of this proposed maximum power point tracking controller are fast identification of the solar system operating point, generating the less fluctuated oriented converter load power, providing more MPP tracking accuracy, less dependence on the solar system installation, and useful for all environmental bad weather conditions. Another problem of solar systems is less voltage production which is improved by introducing a wide voltage gain-boost converter circuit. The features of this converter circuit are less development cost because it does not require more power electronics switches. Here, the proposed IGWM with an AFLC-fed sunlight system is investigated by using MATLAB/Simulink. [ABSTRACT FROM AUTHOR]

In this article, a model predictive control (MPC) with common-mode voltage (CMV) suppression is proposed for single-phase cascaded H-bridge (CHB) inverters, which can also simultaneously achieve control objectives of gridconnected current tracking, voltages balancing of different H-bridge submodules on the DC-side and switching frequency reduction. To suppress high-frequency components of the common-mode voltage without additional switching devices, the algorithm proposed designs the predicted and reference values of the CMV and incorporates them in the cost function. At the same time, the capacitor voltages balancing control is integrated in the calculation of the optimal modulation function of the H-bridge, which reduces the complexity of control effectively. Besides, switching times of the MOSFETs are compared in two cycles. The cost function is constructed to represent comprehensive effect of the control. Finally, an experiment is performed on the hardware-in-the-loop experimental platform. The experimental results show that the proposed algorithm can offer a better voltage THD and reduce the times of switch action by nearly half while maintaining high-precision current tracking and maximum power point of photovoltaic modules, which alleviate the potential electromagnetic interference and cabling problem. [ABSTRACT FROM AUTHOR]

When the battery or supercapacitor is connected to the output of a PV system, the conventional voltage equation expressing its mathematical model usually must be replaced by the current relationship to study the maximum power point tracking (MPPT) control theory. However, hitherto, there is a lack of an attempt to disclose the current constraint relationships at the maximum power point (MPP), which leads to the potential risk of MPPT failure. To solve this problem, in this paper, the MPPT constraint conditions on the basis of currents are built and then a new MPPT control strategy is proposed. In this strategy, a linearized model parameter of a PV cell is used as the bridge to find the current relationships. On the basis of them, some expressions involving the duty cycle are built to directly calculate the control signal of the MPPT controller. Meanwhile, an implementation method is designed to match this proposed MPPT strategy. Finally, some simulation experiments are conducted. The simulation results verify that the proposed MPPT constraint expressions are accurate and workable and that the proposed MPPT strategy and its implementation process are feasible and available. In addition, the simulation results also show that the proposed MPPT strategy has a better MPPT speed and the same MPPT accuracy when the P&O method and fuzzy algorithm are compared. By this work, the MPPT constraint conditions based on current relationships are first found, representing a breakthrough in disclosing the inherent relationships between different currents when the PV system is operating around the MPP. [ABSTRACT FROM AUTHOR]

This article presents a proportional-integral sliding mode control (PI-SMC) approach for a two-mass variable speed wind turbine (VSWT) system. Most studies on wind turbines typically focus mainly on the electromagnetic part of the generators, or even on the high-speed part, considering the shaft stiffness as negligible. However, the generator torque is actually driven by the aerodynamic torque, and a two-mass system like the one studied here plays the role of a transmission element for this power. To address this challenge, the problem of low power generation resulting from wind speed variability is tackled by designing a PI-SMC control law, capable of controlling the mechanical turbine model that optimizes power and torque by tracking the maximum power point (MPPT) for rotational speed and aerodynamic power. To validate the developed theoretical results, an application of the wind turbine system is simulated in Matlab/Simulink, for a particular case. The control used is capable of satisfying the dynamic performance of the systems. [ABSTRACT FROM AUTHOR]

Hybrid Renewable Energy Systems (HRES) have recently been proposed as a way to improve dependability and reduce losses in grid-connected load systems. This research study suggests a novel hybrid optimization technique that regulates UPQC in order to address the Power Quality (PQ) problems in the HRES system. The load system serves as the primary link between the battery energy storage systems (BESS), wind turbine (WT), and solar photovoltaic (PV) components of the HRES system. The major objective of the study is to reduce PQ issues and make up for the load requirement inside the HRES system. The addition of an Optimized Fractional Order Proportional Integral Derivative (O-FOPID) controller improves the efficiency of the UPQC. The Crow-Tunicate Swarm Optimization Algorithm (CT-SOA), an enhanced variant of the traditional Tunicate Swarm Optimization (TSA) and Crow Search Optimization (CSO), is used to optimize the control parameters of the FOPID controller. Utilizing the MATLAB/Simulink platform, the proposed method is put into practice, and the system's performance is assessed for sag, swell, and Total Harmonic Distortion (THD). The THD values for the PI, FOPID, and CSA techniques, respectively, are 5.9038%, 4.9592%, and 3.7027%, under the sag condition. This validates the superiority of the proposed approach over existing approaches. [ABSTRACT FROM AUTHOR]

The present power production companies are working on renewable energy systems because their features are more reliable for the local energy consumers, high continuity in the energy production, and less cost is required for maitainence. In this article, the proton exchange membrane fuel stack (PEMFS) renewable energy is utilized to supply energy to the automotive systems. Here, the PEMFS is selected because of its merits are high energy density, quick system response concerning the source operational temperature, and more suitable for electric vehicle application. However, the PEMFS supplied voltage is completely nonlinear which is solved by utilizing the modified particle swarm optimization with adaptive neuro-fuzzy inference system (MPSO with ANFIS) controller. This hybridization-based maximum power point tracking controller provides more accuracy, high power point identifying speed, best dynamic response at different fuel stack functioning temperature conditions, and easy maitainence. Here, the fuel stack generated current is very high which is optimized by introducing the new DC–DC converter. The advantages of this DC–DC converter are more voltage transformation ratio, low-level voltage stress appearing across the switches, and wide voltage gain. The overall system is investigated by utilizing the MATLAB/Simulink tool. [ABSTRACT FROM AUTHOR]

As the significance and complexity of solar panel performance, particularly at their maximum power point (MPP), continue to grow, there is a demand for improved monitoring systems. The presence of variable weather conditions in Maroua, including potential partial shadowing caused by cloud cover or urban buildings, poses challenges to the efficiency of solar systems. This study introduces a new approach to tracking the Global Maximum Power Point (GMPP) in photovoltaic systems within the context of solar research conducted in Cameroon. The system utilizes Genetic Algorithm (GA) and Backstepping Controller (BSC) methodologies. The Backstepping Controller (BSC) dynamically adjusts the duty cycle of the Single Ended Primary Inductor Converter (SEPIC) to align with the reference voltage of the Genetic Algorithm (GA) in Maroua's dynamic environment. This environment, characterized by intermittent sunlight and the impact of local factors and urban shadowing, affects the production of energy. The Genetic Algorithm is employed to enhance the efficiency of BSC gains in Maroua's solar environment. This optimization technique expedites the tracking process and minimizes oscillations in the GMPP. The adaptability of the learning algorithm to specific conditions improves energy generation, even in the challenging environment of Maroua. This study introduces a novel approach to enhance the efficiency of photovoltaic systems in Maroua, Cameroon, by tailoring them to the specific solar dynamics of the region. In terms of performance, our approach surpasses the INC-BSC, P&O-BSC, GA-BSC, and PSO-BSC methodologies. In practice, the stabilization period following shadowing typically requires fewer than three iterations. Additionally, our Maximum Power Point Tracking (MPPT) technology is based on the Global Maximum Power Point (GMPP) methodology, contrasting with alternative technologies that prioritize the Local Maximum Power Point (LMPP). This differentiation is particularly relevant in areas with partial shading, such as Maroua, where the use of LMPP-based technologies can result in power losses. The proposed method demonstrates significant performance by achieving a minimum 33% reduction in power losses. [ABSTRACT FROM AUTHOR]

This research aims to implement an already developed algorithm to obtain the maximum power transfer of a solar generation field based on a dynamic approach. The study addresses the sizing of the load to be supplied, which is a residential building. On the other hand, it also considers the field sizing as a function of the load and the operating characteristics of the selected inverter. The irradiance data correspond to the hourly record of a station that is part of the network of meteorological stations in Quito. Quito was chosen as the location for this research due to the optimization algorithm's practical application and the availability of experimental equipment. The demand sizing is based on the regulations of the distribution company with jurisdiction in the area, which makes it a suitable test bed for the algorithm. The optimization algorithm is developed using Python (version 3.9), and the analysis of the behavior of the solar panels is performed by dynamic modeling using the Vensim software (version 10.1.2). Finally, comparative results are presented between using and not using the investigated circuit and algorithm in the photovoltaic system, obtaining an improvement in the generation over a system without the use of these improvements, validating these results by implementing them in a test system, obtaining ranges higher than 10% of the initially generated power. [ABSTRACT FROM AUTHOR]

In order to enhance the support capability of photovoltaic inverters for new energy microgrid systems, grid-forming control technology has attracted widespread attention, with Virtual Synchronous Generator (VSG) emerging as a research frontier. This paper integrates hybrid energy storage systems with photovoltaic generation to provide stable voltage support and power compensation for the system. In addition, leveraging the variability of the virtual parameters J and D in traditional VSGs, an adaptive grid-forming photovoltaic inverter control strategy based on fuzzy algorithm is proposed. Furthermore, to reduce the frequency deviation caused by load transients during islanding operation, an adaptive droop coefficient based on frequency power limits is introduced. Finally, simulations are conducted under grid-connected and islanded conditions to compare three control methods: fixed parameter control, traditional adaptive control, and the proposed adaptive with fuzzy control. The results demonstrate that integrating adaptive droop coefficients with fuzzy control can effectively improve the frequency stability and dynamic response capability of microgrids. [ABSTRACT FROM AUTHOR]

The fuel cell stack power mismatch problem limits the large-scale application of fuel cells. In order to guarantee the normal operation of the series fuel cell bank under fault condition, this paper proposes a multi-port DC converter for fuel cell distributed maximum power tracking based on the coupled inductor principle. The converter is based on the voltage equalization method and consists of a series fuel cell bank with a diode clamping circuit and a Boost converter in sequential cascade. In contrast to the degraded usage method of fuel cell stacks under fault conditions, the voltage equalization strategy does not affect the lifetime of non-faulty fuel cell units, so the overall system is more efficient. The proposed converter combines high output voltage gain and cell voltage equalization due to the use of only one switching tube. Simulation models are used to verify the feasibility and advancement of the proposed converter. [ABSTRACT FROM AUTHOR]

One of the most known and usable renewable energy is photovoltaic solar energy. Its properties such as recursivity, cleanness, limitlessness, and reliability make it the most useful source of energy. Some undesirable natural (irradiance and temperature) variation affects the photovoltaic solar modules' characteristics. However, photovoltaic PV solar power needs to be monitored accurately, effectively, and efficiently in order to keep the global maximum power point (GMPP) steady. Therefore, this paper presents a modified multi-stepped constant current based on the gray wolf optimization (MMSCC-GWO) algorithm for photovoltaic systems. The proposed technique utilizes a multi-step constant current to the pack of wolves by monitoring the inside and the outside step of the hierarchical wolves. This proposed (MMSCC-GWO) algorithm accurately tracks the maximum power point from the photovoltaic systems under different partial shading conditions (PSCs). A comparative result with other conventional methods is investigated and the simulation results carried out in the MATLAB/Simulink environment reveal that the proposed approach outperforms the existing techniques in terms of efficiency, tracking time, and accuracy. [ABSTRACT FROM AUTHOR]

This paper presents a novel maximum power point tracking control for a stand-alone photovoltaic (PV) system based on a robust polynomial static output feedback control law subject to input saturation. In detail, a DC/DC boost converter is used to regulate the load and extract the maximum power from the photovoltaic panel. First, a polynomial fuzzy model is used to represent the photovoltaic system. Then, as this control method is based on a reference model, a regression plane is used to generate the desired trajectory representing the optimal dynamics where the PV system supplies maximum power. Then, in order to reduce the number of required sensors, a polynomial output feedback controller was developed, in which the problem of converter performance degradation resulting from duty cycle saturation was avoided by using a saturated control approach. The controller gains have been obtained by solving a sum-of-squares optimization problem, where the H ∞ performance criterion is applied to guarantee the stability of the closed-loop system while achieving an optimal rejection level of external disturbances. To evaluate the performance of the suggested controller, a number of simulations and comparisons were carried out in MATLAB/Simulink environment and under various scenarios of weather conditions. [ABSTRACT FROM AUTHOR]

Under partial shading conditions (PSCs), photovoltaic (PV) systems exhibit non-uniform P-V characteristic curves with multiple local maximum power points (LMPP). Consequently, conventional maximum power point tracking (MPPT) algorithms often fail to accurately track the global maximum power point (GMPP), becoming trapped at local maxima and resulting in power loss. This paper introduces a novel MPPT controller based on the weighted mean of vectors (INFO) optimization algorithm to address these challenges. The INFO algorithm integrates three key operators: updated law, vector combination, and local search, offering advantages such as rapid convergence, high efficiency, and optimized power extraction under both PSCs and temperature changes (TCs). To validate the effectiveness of the INFO algorithm under PSCs and TCs, a partial shading platform featuring three PV modules with identical characteristics but varying radiation levels is utilized. Simulation studies compare the INFO algorithm against traditional perturb and observe (P&O), particle swarm optimization (PSO), and overall distribution particle swarm optimization (OD-PSO) algorithms in terms of MPPT performance. Results demonstrate that the INFO algorithm achieves a 60% reduction in tracking time and a 0.02% increase in MPPT controller efficiency compared to these methods. Overall, the proposed INFO algorithm achieves a balanced approach between exploration and exploitation stages, enhancing robustness, efficiency, and reducing tracking time in MPPT applications. [ABSTRACT FROM AUTHOR]

The "double carbon" policy promotes an increasing ratio of new energy installation and generation capacity annually, reducing system inertia and rendering the grid-forming (GFM) power grid increasingly susceptible to frequency fluctuations and other issues. This paper designs a power–frequency controller for grid-forming distributed photovoltaic systems by integrating LADRC and VSG control, aiming to enhance system robustness and stability under disturbances or faults. Furthermore, this study introduces the particle swarm optimization (PSO) algorithm based on LADRC principles to optimize LADRC, thereby improving the robustness and stability of grid-forming distributed photovoltaic systems to a certain extent. The feasibility and effectiveness of these two proposed control strategies are analyzed and validated separately using the MATLAB/Simulink R2022a simulation platform. [ABSTRACT FROM AUTHOR]

This paper presents an innovative AI-based method for autonomous inspection, designed to enhance energy production efficiency by optimizing cleaning strategies for soiled photovoltaic panels, using advanced artificial intelligence algorithms to analyze panel conditions and environmental factors in real-time, allowing for targeted cleaning interventions. Based on the advanced YOLOv8 deep learning algorithm and computer vision approach, the proposed method offers distinct advantages in real-time detection and classification of various types of soiling and dust accumulation compared on solar panels to traditional methods, and underwent satisfactory testing across diverse scenarios. The NVIDIA Jetson Nano, the Raspberry Pi4 embedded devices, and the Raspberry Pi4 combined with NCS2 accelerator are used for implementing our approach. A comparison aims to provide a detailed exploration of the most suitable embedded platform for deploying our advanced system was discussed. This comparison considers processing speed and accuracy, energy consumption, and overall performance in executing the computationally intensive tasks. The results demonstrate that our model achieves high accuracy in detecting soiling and enhancing the model's detection speed. With an average precision of 99.5%, this approach ensures accurate fault identification, underscoring the effectiveness of computer vision using deep learning algorithms for detection tasks across a wide range of scenarios. [ABSTRACT FROM AUTHOR]

To maintain a dependable and sustainable power supply in a microgrid system, it is crucial to combine renewable energy sources with hybrid energy backup. To achieve maximum output power from solar source, a high gain DC-DC boost converter is managed using the dual Kalman filter based perturb and observe approach. A sliding mode current controller at a three phase inverter with an LC filter is intended to follow an undisturbed reference voltage. To effectively manage the power flow and optimize the utilization of available resources, a robust power management algorithm is required. The novel power management algorithm for a solo operated renewable distribution generation unit with hybrid energy backup in a microgrid is introduced. The algorithm aims to dynamically allocate power among various sources, storage systems, and loads, considering their characteristics and the overall system constraints. The algorithm utilizes sliding mode control techniques to regulate the current flow from the renewable generator and effectively manage the power allocation among different energy sources, storage systems, and loads. [ABSTRACT FROM AUTHOR]

This paper explores the challenges associated with the control of a two-stage three-phase electrical grid connected to a photovoltaic (PV) system. The objectives encompass: i) maximizing the available PV power, ii) controlling the DC-link voltage to a predetermined setpoint, and iii) considering that power quality has become an important measure in a distribution electrical network where different loads are connected, the third objective will mainly focus on ensuring power factor correction (PFC). To achieve these objectives, two loops of nonlinear controller are developed. In the outer loop, the duty cycle of a boost converter is controlled using a hybrid technique of backstepping technique and the perturb & observe (P&O) algorithm. In addition, the inner loop employs a hybrid automaton approach to tackle the challenges of a three-phase shunt active power filter (SAPF). The results have been verified through numerical simulation using MATLAB/Simulink power systems environment. [ABSTRACT FROM AUTHOR]

This paper presents the design of a digital twin for a 6U CubeSat electrical power system, including the solar arrays, solar array regulators, battery, power distribution unit, and load subsystems. The digital twin is validated by comparing its real-time outputs with those of the physical system. Experimental tests confirm its feasibility, showing that the digital twin's real-time outputs closely match those of the physical system. Additionally, the digital twin can be used for control-hardware-in-the-loop and power-hardware-in-the-loop tests, allowing the real-time integration of simulated subsystems with hardware. This capability facilitates testing of new subsystems and optimization during the project's development phases. Additionally, to demonstrate the advanced capabilities of this model, the digital twin is used to simulate the CubeSat electrical power system behavior in real time throughout a complete orbital cycle in low Earth orbit conditions. This simulation provides valuable insights into the CubeSat operation by capturing the transient and steady-state responses of the EPS components under real orbital conditions. The results obtained indicate that the digital twin significantly enhances the testing and optimization process of new subsystems during the development phases of the project. Moreover, the capabilities of the digital twin can be further augmented by incorporating real-time telemetry data from the CubeSat, resulting in a highly accurate replication of the satellite's in-orbit behavior. This approach is crucial for identifying and diagnosing failures or malfunctions in the electrical power system, ensuring the robust and reliable operation of the CubeSat. [ABSTRACT FROM AUTHOR]

The paper presents a normalized, varying step size-based least mean square-based control for a standalone microgrid and Ant Lion optimization-based maximum power point tracking. This modified version of the incremental conductance algorithm addresses issues like slow dynamic response, fixed step size issues, and steady state oscillations. Comparative analysis with well-known techniques shows that Ant Lion optimizes the tracking of maximum power points more accurately, with fewer oscillations and increased efficiency. Power management and power quality are maintained through proposed adaptive voltage source converter control. The proposed voltage control shows better performance under various dynamic and steady conditions. [ABSTRACT FROM AUTHOR]

Parameter identification of solar photovoltaic (PV) cells is crucial for the PV system modeling. However, finding optimal parameters of PV models is an intractable problem due to the highly nonlinear characteristics between currents and voltages in different environments. To address this problem, whale optimization algorithm (WOA)-based meta-heuristic algorithm has turned out to be a feasible and effective approach. As a highly promising optimization algorithm, different enhanced WOA variants have been proposed. Nevertheless, there has been no comparative study of WOA and its variants for parameter identification of PV models so far. To further investigate and analyze the performance of WOA in the studied problem, this work applied and compared WOA and ten enhanced WOA variants for identifying five PV model parameters. Different evaluation indices including solution accuracy, search robustness, and convergence curve were employed to reveal their performance variation. Based on the simulation results, a multi-model statistical analysis with the Friedman test at a confidence level 0.05 was conducted to rank all algorithms. EWOA that hybridizes the sorting-based differential mutation operator and the Lévy flight strategy ranked first and its performance was further verified. Besides, according to the simulation results, possible effective improvement directions for WOA in tackling this intractable problem are concluded to guide future work. [ABSTRACT FROM AUTHOR]

This paper presents a comparative study between traditional and intelligent Maximum Power Point Tracking (MPPT) algorithms for Photovoltaic (PV) powered DC Shunt Motors. Given the nonlinearity of PV systems, they require nonstandard approaches to harness their full potential. Each PV module has a unique maximum power point on its IV curve due to its nonlinear characteristic nature. Power electronic converters are utilized to enable operation at that point. There are many different algorithms described in the introduction, each with its have their own advantages and drawbacks. Recognizing the potential enhancement of PV system efficiency through effective Maximum Power Point (MPP) tracking, this paper evaluates five MPPT methods under varying DC loads. The five algorithms will be as follows: Incremental Conductance and Perturb and Observe as traditional algorithms. Fuzzy Logic Control, Artificial Neural Networks, and Adaptive Neuro-Fuzzy Inference Systems as Intelligent Algorithms. While traditional algorithms generally produced acceptable results except for Perturb & Observe, intelligent algorithms performed well under rapidly changing solar radiation conditions. Due to inadequate data, intelligent algorithms relying on data training struggled to track the maximum power point when the temperature changed due to inadequate data used for the training. The analysis focuses on the time required by each method to reach peak power under different load conditions, solar irradiance, and temperature variations. The advantages and disadvantages of each MPPT with a shunt DC motor are detailed in the comparative study. [ABSTRACT FROM AUTHOR]

Solar photovoltaic energy is a vital renewable resource because it is clean, endless, and pollution‐free. Due to the fast growth of the semiconductor and power electronics sectors, photovoltaic (PV) technologies are climbing significant attention in modern electrical power applications. Operating PV energy conversion systems at the maximum power point is essential for getting the maximum power output and raising efficiency. This paper proposes a regression‐based Perturb and Observe method to quickly find a global maximum power point, avoiding being stuck in local maxima, likewise analytical and metaheuristic methods. The improved control focuses on the narrowed search areas by linear and non‐linear regression analyses using the generated PV model on a flexible Python environment. Furthermore, the method's accuracy is validated in real time under variable temperatures, irradiations, and loads. This method was proven with a hardware implementation. The proposed method is more than 98% accurate and can withstand long‐term modelling. The suggested regression‐based perturbation and observation method provided a short learning time and easy implementation. Additionally, the dynamic recorded results can be visualized for researchers to utilize efficiently. [ABSTRACT FROM AUTHOR]

DC microgrids are getting more attention because majority of the renewable energy sources generate DC output voltage and also modern gadgets require DC voltage for its operation. In this work, high gain SEPIC (HGSC) topology is derived from switched inductor voltage boosting cell (SIVBC). The HGSC converter provides continuous source current due to SIVBC and high conversion ratio and achieves maximum efficiency of 97.88% when compared with the existing SEPIC topology. The operating modes, conversion ratio expression, power loss distribution, voltage drop, current stress of the semiconductor devices, and efficiency are also analysed. In DC microgrids, the HGSC intends to track the peak power from solar PV array. An incremental conductance algorithm is employed to track the peak power of the solar PV modules. The power flow in the microgrid system is analysed by employing synchronous reference frame theory‐based current controller. In order to validate the theoretical concepts of the HGSC converter, the hardware model is developed for the load rating of 1,000 W/380 V output voltage. [ABSTRACT FROM AUTHOR]

This paper studies the possibility of connecting Wind Farms (WF) to the electric grid with the use of finite space model predictive command (FS-MPC) to manage wind farms to improve the quality of the current output from the doubly-fed induction generator (DFIG) with considering fault ride-through technique. This proposed system can generate active power and enhance the power factor. Furthermore, the reduction of harmonics resulting from the connection of non-linear loads to the electrical grid is achieved through the self-active filtering mechanism in DFIGs-WF, facilitated by the now algorithm proposed. FS-MPC technique has the ability to improve system characteristics and greatly reduce active power ripples. Therefore, MATLAB software is used to implement and verify the safety, performance, and effectiveness of this designed technique compared to the conventional strategy. The results obtained demonstrated the effectiveness of the proposed algorithm in handling the four operational modes (Maximum power point tracking, Delta, Fault, and Filtering). Additionally, the suggested technique exhibited flexibility, robustness, high accuracy, and fast dynamic response when compared to conventional strategies and some recently published scientific works. On the other hand, the THD value of the current was significantly reduced, obtaining at one test time the values 56.87% and 0.32% before and after filtering, respectively 27.50% and 0.26% at another time of testing, resulting in an estimated THD reduction percentage of 99.43% and 99.05%, respectively. These high percentages prove that the quality of the stream is excellent after applying the proposed strategy. [ABSTRACT FROM AUTHOR]

With its technical advantages of high speed, low latency, and broad connectivity, fifth-generation mobile communication technology has brought about unprecedented development in numerous vertical application scenarios. However, the high energy consumption and expansion difficulties of 5G infrastructure have become the main obstacles restricting its widespread application. Therefore, aiming to optimize the energy utilization efficiency of 5G base stations, a novel distributed photovoltaic 5G base station DC microgrid structure and an energy management strategy based on the Curve Fitting–Perturb and Observe–Incremental Conductance (CF-P&O-INC) Maximum Power Point Tracking (MPPT) algorithm from the perspectives of energy and information flows are proposed. Simulation results show that the proposed MPPT algorithm can increase the efficiency to 99.95% and 99.82% under uniform irradiation and partial shading, respectively. Under the proposed strategy, when the base station load changes drastically, the voltage fluctuation of the DC bus is less than 1.875%, and returns to a steady state within 0.07s, alleviating the high energy consumption of 5G base stations effectively and achieving coordinated optimization management of various types of energy in multi-source power supply systems. [ABSTRACT FROM AUTHOR]

Partial shading conditions can cause low output power, hotspots, and a reduced lifespan in photovoltaic arrays. Interconnection (IC) and differential power processing (DPP) can be used to mitigate these effects. When individually applied to an array, these techniques can significantly increase the generated power. A few authors studied the combined use of these schemes under specific conditions such as large-scale arrays or a complex combination of several techniques, making it difficult to identify the individual contribution of each technique. Here, we aimed to determine whether the combined use of a switching-inductor DPP circuit and a total-cross-tied interconnection scheme presents better performance than each standalone technique, using a small-scale photovoltaic array. An array was tested using IC, DPP, and a combination of both techniques, and the array was subjected to 13 shading patterns and two irradiance levels. The performance in each case was assessed using maximum output power, performance ratio, mismatch power loss, and power enhancement indicators. The results showed that a standalone differential power processing circuit presents better performance than when it is combined with an interconnection. The DPP showed performance ratio values of up to 97%, mismatch power losses lower than 36.9%, and a power enhancement of up to 95.9%. The standalone interconnection shows the worst performance among the three techniques. [ABSTRACT FROM AUTHOR]

In response to challenges such as voltage limit violations, excessive currents, and power imbalances caused by the integration of distributed photovoltaic (distributed PV) systems into the distribution network, this study proposes at two-level optimization configuration method. This method effectively balances the grid capacity and reduces the active power losses, thereby decreasing the operating costs. The upper-level optimization enhances the distribution network's capacity by determining the siting and sizing of distributed PV devices. The lower-level aims to reduce the active power losses, improve the voltage stability margins, and minimize the voltage deviations. The upper-level planning results, which include the siting and sizing of the distributed PV, are used as initial conditions for the lower level. Subsequently, the lower level feeds back its optimization results to further refine the configuration. The model is solved using an improved second-order oscillating chaotic map particle swarm optimization algorithm (SCMPSO) combined with a second-order relaxation method. The simulation experiments on an improved IEEE 33-bus test system show that the SCMPSO algorithm can effectively reduce the voltage deviations, decrease the voltage fluctuations, lower the active power losses in the distribution network, and significantly enhance the power quality. [ABSTRACT FROM AUTHOR]