Search

Radiation accounts for a significant fraction of the human body and environment heat exchange and strongly impacts thermal comfort and safety. The direct radiative exchange between an individual and a source or sink can be quantified using the effective (f

Thermal comfort research has utilized various sensors and models to estimate the mean radiant temperature (MRT) experienced by a human, including the standard black globe thermometer (SGT), acrylic globe thermometers (AGT), and cylindrical radiation thermometers (CRT). Rather than directly measuring radiation, a temperature is measured in the center of these low-cost sensors that can be related to MRT after theoretically accounting for convection. However, these sensors have not been systematically tested under long-term hot and clear conditions. Further, under variable weather conditions, many issues can arise due to slow response times, shape, inaccuracies in material properties and assumptions, and color (albedo, emissivity) inconsistencies. Here, we assess the performance of MRT produced by various heat transfer models, with and without new average surface temperature ( $$ {\overline{T}}_{\mathrm{s}} $$ ) correction factors, using five instruments—the SGT (15 cm, black), tan and black CRTs, gray and black 38 mm AGTs—compared to 3D integral radiation measurements. Measurements were taken on an unobscured roof throughout summer-to-early-fall months in Tempe, Arizona, examining 58 full-sun days. Deviations without correcting for asymmetrical surface heating—found to be the main cause of errors—reached ± 15–20 °C MRT. By accounting for asymmetric heating through $$ {\overline{T}}_{\mathrm{s}} $$ calculations, new corrective algorithms were derived for the low-cost sensor models. Results show significant improvements in the estimated MRT error for each sensor (i.e., ∆MRTmodel − IRM) when applying the $$ {\overline{T}}_{\mathrm{s}} $$ corrections. The tan MRTCRT improved from 1.9 ± 6.2 to −0.1 ± 4.4 °C, while the gray AGT and SGT showed improvements from −1.6 ± 7.2 to −0.4 ± 6.3 °C and − 6.6 ± 6.4 to − 0.03 ± 5.7 °C, respectively. The new corrections also eliminated dependence on other meteorological factors (zenith, wind speed). From these results, we provide three simple equations for CRT, AGT, and SGT correction for future research use under warm-hot and clear conditions. This study is the most comprehensive empirical assessment of various low-cost instruments with broad applicability in urban climate and biometeorological research.

Thermal comfort research has utilized various sensors and models to estimate the mean radiant temperature (MRT) experienced by a human, including the standard black globe thermometer (SGT), acrylic globe thermometers (AGT), and cylindrical radiation thermometers (CRT). Rather than directly measuring radiation, a temperature is measured in the center of these low-cost sensors that can be related to MRT after theoretically accounting for convection. However, these sensors have not been systematically tested under long-term hot and clear conditions. Further, under variable weather conditions, many issues can arise due to slow response times, shape, inaccuracies in material properties and assumptions, and color (albedo, emissivity) inconsistencies. Here, we assess the performance of MRT produced by various heat transfer models, with and without new average surface temperature ([Formula: see text]) correction factors, using five instruments-the SGT (15 cm, black), tan and black CRTs, gray and black 38 mm AGTs-compared to 3D integral radiation measurements. Measurements were taken on an unobscured roof throughout summer-to-early-fall months in Tempe, Arizona, examining 58 full-sun days. Deviations without correcting for asymmetrical surface heating-found to be the main cause of errors-reached ± 15-20 °C MRT. By accounting for asymmetric heating through [Formula: see text] calculations, new corrective algorithms were derived for the low-cost sensor models. Results show significant improvements in the estimated MRT error for each sensor (i.e., ∆MRT

This work uses elementary theoretical arguments to estimate whether softening of the surface could be used, along with surface texture and chemistry, to control superheat required for onset of nucleate boiling. For an ideal, smooth surface a mild decrease of the required superheat is predicted. In turn, an approximate closed-form model of vapor trapping and bubble seeding from soft surface with conical cavities shows linear dependence between the required superheat and the substrate’s shear modulus. Based on these results, considerations involved in implementing soft coatings for boiling applications and relevant outstanding fundamental questions are also briefly discussed.

A multi-fold enhancement in the rate of heat transfer can be achieved by promoting the dropwise condensation mode (DWC) over the filmwise condensation mode. Recent material developments are increasing the chances that DWC will transition into industrial applications. Consequently, the ability to quantitatively model heat transfer rate during DWC of water and low surface tension liquids will become increasingly important in design of condensers. DWC heat transfer models developed so far consider only conduction inside the condensate droplets. However, scaling analysis shows that, in contrast to buoyancy driven flow, thermocapillary flow could be present in a wide range of droplet sizes in industrially relevant conditions. In the present work, we theoretically quantify the effect of Marangoni convection on heat transfer across individual condensing droplets as well as its impact on the overall DWC heat transfer. Specifically, we use Finite Element simulations to estimate the change in heat transfer that thermocapillary flow induces in condensing drops with spherical cap geometry. Besides water, we also study heat transfer across drops of organic liquids including toluene, ethanol, and pentane. Our results indicate that heat transfer rates across droplets are higher in the conjugate heat transfer case than the conduction only case (up to 6-fold increase for large water droplets on hydrophobic and superhydrophobic surfaces under extreme subcooling of 50 K). However, irrelevant of fluid and contact angle, for smaller droplets with radius below 100 µm at most a twofold thermocapillary heat transfer enhancement was obtained. When integrated with the dropsize distribution, these multi-fold increases in heat transfer across individual drops translate in most cases to a minor 10% or lower increase in the overall dropwise condensation heat transfer coefficient. Thus, with exception of a few special cases, the Marangoni flow contribution to DWC heat transfer coefficient is on the order of typical experimental uncertainties and can be neglected.

This work reports new evidence of the versatility of soft and environmentally responsive micron-sized colloidal gel particles as stabilizers at ionic liquid-water droplet interfaces. These particles display a duality with properties ascribed typically to both polymeric and colloidal systems. The utilization of fluorescently labeled composite microgel particles allows in-situ and facile visualization without the necessity of invasive sample preparation. When the prepared particles form monolayers equilibrated at the ionic liquid-water interface on fully covered droplets, the colloidal lattice re-orders itself depending on the surface charge of these particles. Finally, we demonstrate that the spontaneously formed and densely packed layer of microgel particles can be employed for extraction applications, as the interface remains permeable to small active species.

The degradation of corrosion preventative coatings contributes to the high cost and time requirements for maintaining structures in harsh environments. However, the development of new hydrophobic coatings holds the promise of extending the usable life of structures in marine environments. In this work, we quantify the barrier properties and corrosion resistance of two novel highly hydrophobic polysiloxane formulations and the legacy silicone alkyd topcoat used on the topside of Navy’s ships, all with haze gray pigmentation. Based on FTIR-ATR and EIS measurements of the pristine coatings, both the single- (1K) and the two-component (2K) polysiloxane provide significantly improved barrier characteristics (lower water diffusion coefficient and capacitance) than the silicone alkyd. These results were confirmed through a 3-month-long immersion corrosion test, which also showed that the 1K and 2K polysiloxane coatings had comparable degradation characteristic and remained highly hydrophobic.

“Deadly heat waves: it’s only getting worse”, a headline from this summer, succinctly summarizes recent weather and predictions on its future patterns. According to World Metrological Organization,...

Thermal contact resistance at the finger-object interface plays a significant role in our thermal perception and is an important parameter for the design of a myriad of electronics and thermal devices. Currently, its value is measured experimentally or, more commonly, is estimated using a semi-empirical model. This model was developed by Cooper, Mikic, and Yovanovich (CMY) in the 1960s for predicting contact resistance of metal-metal interfaces in a vacuum. In this work, it is shown that measured value of finger-object contact resistance is better predicted by a more recent correlation by Prasher and Matayabas (PM) that was developed by fitting contact resistance data for silicone gel-metal surface interfaces in microelectronic applications. Furthermore, it is show that the functional form of the empirical PM correlation can be derived using scale analysis of the finger-solid contact scenario, consequently can be considered a physics-based model. Comparing the two models against two previously published experimental data sets demonstrates that the PM model predicts well the thermal resistance between finger and variety of materials over a wide range of contact pressures. Specifically, for finger contact with significantly more conductive materials (thermal conductivity above 1 Wm−1K−1) including aluminum, BaF2 crystal, and marble a good prediction of contact resistance can be attained. For skin contact with less conductive materials, such as wood, both models become highly sensitive to the substrate’s thermal conductivity value and provide only an order of magnitude estimate. The main implications of these results and relevant outstanding questions are also briefly discussed.

Condensation on liquids has been studied extensively in context of breath figure templating, materials synthesis and enhancing heat transfer using liquid impregnated surfaces. However, the mechanics of nucleation and growth on liquids remains unclear, especially on liquids that spread on the condensate. By examining the energy barriers of nucleation, we provide a framework to choose liquids that can lead to enhanced nucleation. We show that due to limits of vapor sorption within a liquid, nucleation is most favoured at the liquid–air interface and demonstrate that on spreading liquids, droplet submergence within the liquid occurs thereafter. We provide a direct visualization of the thin liquid profile that cloaks the condensed droplet on a liquid impregnated surface and elucidate the vapour transport mechanism in the liquid films. Finally, we show that although the viscosity of the liquid does not affect droplet nucleation, it plays a crucial role in droplet growth., MIT Energy Initiative, Masdar Institute of Science and Technology (Grant 69238330)

International audience; Water droplets condensing on solidified phase change materials such as benzene and cyclohexane near their melting point show in-plane jumping and continuous "crawling" motion. The jumping drop motion has been tentatively explained as an outcome of melting and refreezing of the materials surface beneath the droplets and can be thus considered as an inverted Leidenfrost-like effect (in the classical case vapor is generated from a droplet on a hot substrate). We present here a detailed investigation of jumping movements using high-speed imaging and static cross-sectional cryogenic focused ion beam scanning electron microscope imaging. Our results show that drop motion is induced by a thermocapillary (Marangoni) effect. The in-plane jumping motion can be delineated to occur in two stages. The first stage occurs on a millisecond time scale and comprises melting the substrate due to drop condensation. This results in droplet depinning, partial spreading, and thermocapillary movement until freezing of the cyclohexane film. The second stage occurs on a second time scale and comprises relaxation motion of the drop contact line (change in drop contact radius and contact angle) after substrate freezing. When the cyclohexane film cannot freeze, the droplet continuously glides on the surface, resulting in the crawling motion.

The use of silver nanoparticles (AgNPs) in textiles for enhanced anti-microbial properties has led to concern about their release and impact on both human and environmental health. Here a novel method for in situ visualization of AgNP release from silver-impregnated wound dressings is introduced. By combining an environmental scanning electron microscope, a gaseous analytical detector and a peltier cooling stage, this technique provides near-instantaneous nanoscale characterization of interactions between individual water droplets and AgNPs. We show that dressings with different silver application methods have very distinct AgNP release dynamics. Specifically, water condensation on dressings with AgNP deposited directly on the fiber surface resulted in substantial and rapid AgNP release. By comparison, AgNP release from wound dressing with nanoparticles grown, not deposited, from the fiber surface was either much slower or negligible. Our methodology complements standard bulk techniques for studying of silver release from fabrics by providing dynamic nanoscale information about mechanisms governing AgNP release from individual fibers. Thus coupling these nano and macro-scale methods can provide insight into how the wound dressing fabrication could be engineered to optimize AgNP release for different applications.

Rough surfaces immersed under water remain practically dry if the liquid-solid contact is on roughness peaks, while the roughness valleys are filled with gas. Mechanisms that prevent water from invading the valleys are well studied. However, to remain practically dry under water, additional mechanisms need consideration. This is because trapped gas (e.g. air) in the roughness valleys can dissolve into the water pool, leading to invasion. Additionally, water vapor can also occupy the roughness valleys of immersed surfaces. If water vapor condenses, that too leads to invasion. These effects have not been investigated, and are critically important to maintain surfaces dry under water. In this work, we identify the critical roughness scale, below which it is possible to sustain the vapor phase of water and/or trapped gases in roughness valleys – thus keeping the immersed surface dry. Theoretical predictions are consistent with molecular dynamics simulations and experiments., Scientific Reports, 5, ISSN:2045-2322

Compared to the significant body of work devoted to surface engineering for promoting dropwise condensation heat transfer of steam, much less attention has been dedicated to fluids with lower interfacial tension. A vast array of low-surface tension fluids such as hydrocarbons, cryogens, and fluorinated refrigerants are used in a number of industrial applications, and the development of passive means for increasing their condensation heat transfer coefficients has potential for significant efficiency enhancements. Here we investigate condensation behavior of a variety of liquids with surface tensions in the range of 12 to 28 mN/m on three types of omniphobic surfaces: smooth oleophobic, re-entrant superomniphobic, and lubricant-impregnated surfaces. We demonstrate that although smooth oleophobic and lubricant-impregnated surfaces can promote dropwise condensation of the majority of these fluids, re-entrant omniphobic surfaces became flooded and reverted to filmwise condensation. We also demonstrate that on the lubricant-impregnated surfaces, the choice of lubricant and underlying surface texture play a crucial role in stabilizing the lubricant and reducing pinning of the condensate. With properly engineered surfaces to promote dropwise condensation of low-surface tension fluids, we demonstrate a four to eight-fold improvement in the heat transfer coefficient., National Science Foundation (U.S.). Graduate Research Fellowship Program, National Science Foundation (U.S.) (CAREER Award 0952564), MIT Energy Initiative

1. School for Engineering of Transport, Matter and Energy, Arizona State University, Tempe, AZ 85287 2. School of Sustainable Engineering and The Built Environment, Arizona State University Tempe, AZ 85287 3. University of the District of Columbia, Washington, DC 4. Material Measurement Laboratory, National Institute of Standards and Technology, Gaithersburg, MD 20899 5. Department of Mechanical Engineering, Massachusetts Institute of Technology, Cambridge, MA 02139

Extended abstract of a paper presented at Microscopy and Microanalysis 2013 in Indianapolis, Indiana, USA, August 4 – August 8, 2013.

Extended abstract of a paper presented at Microscopy and Microanalysis 2012 in Phoenix, Arizona, USA, July 29 – August 2, 2012.

Extended abstract of a paper presented at Microscopy and Microanalysis 2012 in Phoenix, Arizona, USA, July 29 – August 2, 2012.

Metal-assisted chemical etching (MaCE) of silicon has proven to be a fast and effective method to fabricate 1D, 2D, and 3D micro- to nano-scale features in silicon. It has been shown that platinum catalysts deposited using focused ion beam (FIB) are a viable catalyst for MaCE; however, the feature fidelity of channels etched with FIB patterned catalysts are found to be significantly lower than catalysts formed using e-beam lithography. In this work we show that gallium (Ga+) ions implanted into the silicon during sample exposure result in significant etching in the irradiated regions as well as long-distance etching peripheral regions. The accelerating voltage, dose, and etching time were varied to show that the etch depth depends primarily on accelerating voltage and is largely independent of dose while the width of the peripheral region was found to scale with dose. The slope of the peripheral etching region was found to vary with both accelerating voltage and dose with three different etching times evaluated to examine how the etch profile evolves over time. These results show that Ga+ ions do participate in MaCE and care must be taken when a Ga+ ion based FIB is used.Metal-assisted chemical etching (MaCE) of silicon has proven to be a fast and effective method to fabricate 1D, 2D, and 3D micro- to nano-scale features in silicon. It has been shown that platinum catalysts deposited using focused ion beam (FIB) are a viable catalyst for MaCE; however, the feature fidelity of channels etched with FIB patterned catalysts are found to be significantly lower than catalysts formed using e-beam lithography. In this work we show that gallium (Ga+) ions implanted into the silicon during sample exposure result in significant etching in the irradiated regions as well as long-distance etching peripheral regions. The accelerating voltage, dose, and etching time were varied to show that the etch depth depends primarily on accelerating voltage and is largely independent of dose while the width of the peripheral region was found to scale with dose. The slope of the peripheral etching region was found to vary with both accelerating voltage and dose with three different etching times eva...