Search

This paper presents final results from the EU project AVATAR in which aerodynamic models are improved and validated for wind turbines on a scale of 10 MW and more. Special attention is paid to the improvement of low fidelity engineering (BEM based) models with higher fidelity (CFD) models but also with intermediate fidelity free vortex wake (FVW) models. The latter methods were found to be a good basis for improvement of induction modelling in engineering methods amongst others for the prediction of yawed cases, which in AVATAR was found to be one of the most challenging subjects to model. FVW methods also helped to improve the prediction of tip losses. Aero-elastic calculations with BEM based and FVW based models showed that fatigue loads for normal production cases were over predicted with approximately 15% or even more. It should then be realised that the outcome of BEM based models does not only depend on the choice of engineering add-ons (as is often assumed) but it is also heavily dependent on the way the induced velocities are solved. To this end an annulus and element approach are discussed which are assessed with the aid of FVW methods. For the prediction of fatigue loads the so-called element approach is recommended but the derived yaw models rely on an annulus approach which pleads for a generalised solution method for the induced velocities., Wind Energy

Aerodynamic experiments have been executed in the wind tunnel and on a wind turbine blade to measure the impact of roughness on the airfoil characteristics and the associated effect on rotor performance and to establish the transition location on a rotating blade. The wind tunnel tests have been performed in the low-speed, low-turbulence wind tunnel of TUDelft. The wind turbine tests were carried out at ECN's Wind Turbine Test Site. Roughness simulation material has been installed on the airfoil leading edge to measure the impact on airfoil performance. Microphones were mounted on the airfoil surface to detect the boundary layer laminar to turbulent transition position both on the wind tunnel model and on the wind turbine blade., Wind Energy

Aerodynamic experiments have been executed in the wind tunnel and on a wind turbine blade to measure the impact of roughness on the airfoil characteristics and the associated effect on rotor performance and to establish the transition location on a rotating blade. The wind tunnel tests have been performed in the low-speed, low-turbulence wind tunnel of TUDelft. The wind turbine tests were carried out at ECN's Wind Turbine Test Site. Roughness simulation material has been installed on the airfoil leading edge to measure the impact on airfoil performance. Microphones were mounted on the airfoil surface to detect the boundary layer laminar to turbulent transition position both on the wind tunnel model and on the wind turbine blade., Wind Energy

This paper presents final results from the EU project AVATAR in which aerodynamic models are improved and validated for wind turbines on a scale of 10 MW and more. Special attention is paid to the improvement of low fidelity engineering (BEM based) models with higher fidelity (CFD) models but also with intermediate fidelity free vortex wake (FVW) models. The latter methods were found to be a good basis for improvement of induction modelling in engineering methods amongst others for the prediction of yawed cases, which in AVATAR was found to be one of the most challenging subjects to model. FVW methods also helped to improve the prediction of tip losses. Aero-elastic calculations with BEM based and FVW based models showed that fatigue loads for normal production cases were over predicted with approximately 15% or even more. It should then be realised that the outcome of BEM based models does not only depend on the choice of engineering add-ons (as is often assumed) but it is also heavily dependent on the way the induced velocities are solved. To this end an annulus and element approach are discussed which are assessed with the aid of FVW methods. For the prediction of fatigue loads the so-called element approach is recommended but the derived yaw models rely on an annulus approach which pleads for a generalised solution method for the induced velocities., Wind Energy

This paper presents the most recent results from the EU project AVATAR in which aerodynamic models are improved and validated for wind turbines on a scale of 10 MW and more. Measurements on a DU 00-W-212 airfoil are presented which have been taken in the pressurized DNW-HDG wind tunnel up to a Reynolds number of 15 Million. These measurements are compared with measurements in the LM wind tunnel for Reynolds numbers of 3 and 6 Million and with calculational results. In the analysis of results special attention is paid to high Reynolds numbers effects. CFD calculations on airfoil performance showed an unexpected large scatter which eventually was reduced by paying even more attention to grid independency and domain size in relation to grid topology. Moreover calculations are presented on flow devices (leading and trailing edge flaps and vortex generators). Finally results are shown between results from 3D rotor models where a comparison is made between results from vortex wake methods and BEM methods at yawed conditions., Wind Energy

This paper presents the most recent results from the EU project AVATAR in which aerodynamic models are improved and validated for wind turbines on a scale of 10 MW and more. Measurements on a DU 00-W-212 airfoil are presented which have been taken in the pressurized DNW-HDG wind tunnel up to a Reynolds number of 15 Million. These measurements are compared with measurements in the LM wind tunnel for Reynolds numbers of 3 and 6 Million and with calculational results. In the analysis of results special attention is paid to high Reynolds numbers effects. CFD calculations on airfoil performance showed an unexpected large scatter which eventually was reduced by paying even more attention to grid independency and domain size in relation to grid topology. Moreover calculations are presented on flow devices (leading and trailing edge flaps and vortex generators). Finally results are shown between results from 3D rotor models where a comparison is made between results from vortex wake methods and BEM methods at yawed conditions., Wind Energy

ECN with its partners TU DelŌ, Avent LiDAR Technologies and XEMC Darwind executed the four-year TKI Wind op Zee project LAWINE (LiDAR ApplicaƟon for WInd Energy Efficiency). In this project the applica Ɵon of LiDAR technology has been developed and validated so that it can be used to improve the operaƟon of offshore wind farms with the goal to further reduce the cost of offshore wind power plants. The planned deliverables in the project have been met within Ɵme and budget requirements. Gathering a project team that includes a variety of competences has resulted in a fruiƞul cooperaƟon leading to the following interesƟng project results: 1. It has been verified that ground based LiDAR can be applied for wind resource assessments as well as power and loads assessment campaigns. This way wind turbine performance can be verified without the requirement of expensive masts. 2. Power performance assessments can be performed more accurately by using the wind profile measurements of the LiDAR. 3. Wake characterizaƟon by LiDAR measurements has been demonstrated, which will assist the opƟ- mizaƟon of lay-outs of offshore wind farms. 4. In the project it has been demonstrated that nacelle LiDARs are suitable to be used as basis in power performance assessments. 5. It has been demonstrated that LiDAR measurements in combinaƟon with advanced controllers have significant benefits for rotor speed regulaƟon and reducƟon of faƟgue loads.6. It has been demonstrated that LiDARs can determine yaw misalignment accurately, which is an important aspect to implement the ECN wind farm controllers. 7. ECN developed the LiDAR calibraƟon facility where industry can calibrate its LiDARs in a very effecƟve manner. Such uƟlity is crucial for the successful applicaƟon of LiDARs in wind resource assessments and power performance verificaƟon. These results have been disseminated with researchers and industry over various conferences and workshops., Wind Energy

ECN with its partners TU DelŌ, Avent LiDAR Technologies and XEMC Darwind executed the four-year TKI Wind op Zee project LAWINE (LiDAR ApplicaƟon for WInd Energy Efficiency). In this project the applica Ɵon of LiDAR technology has been developed and validated so that it can be used to improve the operaƟon of offshore wind farms with the goal to further reduce the cost of offshore wind power plants. The planned deliverables in the project have been met within Ɵme and budget requirements. Gathering a project team that includes a variety of competences has resulted in a fruiƞul cooperaƟon leading to the following interesƟng project results: 1. It has been verified that ground based LiDAR can be applied for wind resource assessments as well as power and loads assessment campaigns. This way wind turbine performance can be verified without the requirement of expensive masts. 2. Power performance assessments can be performed more accurately by using the wind profile measurements of the LiDAR. 3. Wake characterizaƟon by LiDAR measurements has been demonstrated, which will assist the opƟ- mizaƟon of lay-outs of offshore wind farms. 4. In the project it has been demonstrated that nacelle LiDARs are suitable to be used as basis in power performance assessments. 5. It has been demonstrated that LiDAR measurements in combinaƟon with advanced controllers have significant benefits for rotor speed regulaƟon and reducƟon of faƟgue loads.6. It has been demonstrated that LiDARs can determine yaw misalignment accurately, which is an important aspect to implement the ECN wind farm controllers. 7. ECN developed the LiDAR calibraƟon facility where industry can calibrate its LiDARs in a very effecƟve manner. Such uƟlity is crucial for the successful applicaƟon of LiDARs in wind resource assessments and power performance verificaƟon. These results have been disseminated with researchers and industry over various conferences and workshops., Wind Energy

This paper presents the most recent results from the EU project AVATAR in which aerodynamic models are improved and validated for wind turbines on a scale of 10 MW and more. Measurements on a DU 00-W-212 airfoil are presented which have been taken in the pressurized DNW-HDG wind tunnel up to a Reynolds number of 15 Million. These measurements are compared with measurements in the LM wind tunnel for Reynolds numbers of 3 and 6 Million and with calculational results. In the analysis of results special attention is paid to high Reynolds numbers effects. CFD calculations on airfoil performance showed an unexpected large scatter which eventually was reduced by paying even more attention to grid independency and domain size in relation to grid topology. Moreover calculations are presented on flow devices (leading and trailing edge flaps and vortex generators). Finally results are shown between results from 3D rotor models where a comparison is made between results from vortex wake methods and BEM methods at yawed conditions., Wind Energy