Search

We report a smartphone–paper-based sensor impregnated with cetyltrimethylammonium bromide modified silver nanoparticles (AgNPs/CTAB) for determination of Fe3+ in water and blood plasma samples. The methodology for determination of Fe3+ is based on the change in signal intensity of AgNPs/CTAB fabricated on a paper substrate after the deposition of analyte, using a smartphone followed by processing with ImageJ software. The mechanism of sensing for detection and determination of Fe3+ is based on the discoloration of AgNPs which impregnated the paper substrate. The discoloration is attributed to the electron transfer reaction taking place on the surface of NPs in the presence of CTAB. Fe3+ was determined when the paper was impregnated with 1 mM AgNPs for 5 min of reaction time and the substrate was kept under acidic conditions. The linear range for determination of total iron in terms of Fe3+ was 50–900 μg L−1 with a limit of determination (LOD) of 20 μg L−1 and coefficient of variation (CV) of 3.2%. The good relative recovery of 91.3–95.0% and interference studies showed the selectivity of the method for determination of total iron in water and blood plasma samples. Smartphone–paper-based sensors have advantages of simplicity, rapidity, user-friendliness, low cost, and miniaturization of the method for on-site determination of total iron compared to methods that require sophisticated analytical instruments.

Copper (Cu) is a key transition metal that is involved in many important biological processes in a cell. Cu is also utilized by the immune system to hamper pathogen growth during infection. However, genome-level knowledge on the mechanisms involved in adaptation to Cu stress is limited. Here, we report the results of a genome-wide reverse genetic screen for Cu-responsive phenotypes in Escherichia coli. Our screen has identified novel genes involved in adaptation to Cu stress in E. coli. We detected multiple genes involved in the biosynthesis and uptake of enterobactin, a siderophore utilized for high-affinity TonB-dependent acquisition of iron (Fe), as critical players in survival under Cu intoxication. We demonstrated the specificity of Cu-dependent killing by chelation of Cu and by genetic complementation of tonB. Notably, TonB is involved in protection from Cu in both laboratory and uropathogenic strains of E. coli. Cu stress leads to increased expression of the genes involved in Fe uptake, indicating that Fur regulon is derepressed during exposure to excess Cu. Trace element analyses revealed that Fe homeostasis is dysregulated during Cu stress. Taken together, our data supports a model in which lack of enterobactin-dependent Fe uptake leads to exacerbation of Cu toxicity, and elucidates the intricate connection between the homeostasis of Cu and Fe in a bacterial cell., Graphical Abstract Graphical AbstractCopper Stress and Iron Homeostasis in E. coli.

Pancreatic beta-cells synthesize and secrete insulin maintaining an organism's energy homeostasis. In humans, beta-cell dysfunction and death contribute to the pathogenesis of type 2 diabetes (T2D). Although the causes of beta-cell dysfunction are complex, obesity-induced low-grade systemic inflammation plays a role. For example, obese individuals exhibiting increased levels of proinflammatory cytokines IL-6 and IL-1beta have a higher risk of beta-cell dysfunction and T2D. Interestingly, obesity-induced inflammation changes the expression of several cellular metal regulating genes, prompting this study to examine changes in the beta-cell metallome after exposure to proinflammatory-cytokines. Primary mouse beta-cells were exposed to a combination of IL-6 and IL-1beta for 48 hours, were chemically fixed and imaged by synchrotron X-ray fluorescent microscopy. Quantitative analysis showed a surprising 2.4-fold decrease in the mean total cellular content of zinc from 158 ± 57.7 femtograms (fg) to 65.7 ± 29.7 fg; calcium decreased from 216 ± 67.4 to 154.3 ± 68.7 fg (control vs. cytokines, respectively). The mean total cellular iron content slightly increased from 30.4 ± 12.2 to 47.2 ± 36.4 fg after cytokine treatment; a sub-population of cells (38%) exhibited larger increases of iron density. Changes in the subcellular distributions of zinc and calcium were observed after cytokine exposure. Beta-cells contained numerous iron puncta that accumulated still more iron after exposure to cytokines. These findings provide evidence that exposure to low levels of cytokines is sufficient to cause changes in the total cellular content and/or subcellular distribution of several metals known to be critical for normal beta-cell function.

Iron is an important micronutrient involved in several mechanisms in the human body and can be an important biomarker. In this work, a simple and disposable microfluidic paper-based analytical device (µPAD) was developed for the quantification of iron in urine samples. The detection was based on the colorimetric reaction between iron(II) and bathophenanthroline and the reduction of iron(III) to iron(II) with hydroxylamine. The developed µPAD enabled iron determination in the range 0.07-1.2 mg/L, with a limit of detection of 20 µg/L and a limit of quantification of 65 µg/L, thus suitable for the expected values in human urine. Additionally, targeting urine samples, the potential interference of the samples color was overcome by incorporating a sample blank assessment for absorbance subtraction. Stability studies revealed that the device was stable for 15 days prior to usage and that the formed colored product was stable for scanning up to 3 h. The accuracy of the developed device was established by analyzing urine samples (#26) with the developed µPAD and with the atomic absorption spectrometry method; the relative deviation between the two sets of results was below 9.5%.

This report provides perspectives concerning dual roles of serum ferritin as a measure of both iron status and of inflammation. We suggest benefits of a lower range of serum ferritin as has occurred for total serum cholesterol and fasting blood glucose levels. Observations during a prospective randomized study using phlebotomy in patients with peripheral arterial disease (PAD) offered unique insights into dual roles of serum ferritin both as an iron status marker and acute phase reactant. Robust positive associations between serum ferritin, interleukin 6 [IL-6], tissue necrosis factor-alpha (TNF-a), and high sensitivity C-reactive protein (hsCRP) were discovered. Elevated serum ferritin and IL-6 levels associated with increased mortality and with reduced mortality at ferritin levels < 100 ng/mL. Epidemiologic studies demonstrate similar outcomes. Extremely elevated ferritin and IL-6 levels also occur in individuals with high mortality due to SARS-CoV-2 infection. Disordered iron metabolism reflected by a high range of serum ferritin level signals disease severity and outcomes. Based upon experimental and epidemiologic data, we suggest testing the hypotheses that optimal ferritin levels for cardiovascular mortality reduction range from 20—100 ng/mL with % transferrin levels from 20–50%, to ensure adequate iron status and that ferritin levels above 194 ng/mL associate with all-cause mortality in population cohorts., Graphical Abstract Graphical Abstract

In this work, a new chemiluminescence (CL) system of Co-Fe prussian blue analogs nanocubes (Co-Fe PBA NCs) that can catalyze luminol to produce strong CL in the absence of H2O2 was established. Co-Fe PBA NCs have the property of oxidase-like activity, and it can catalyze the generation of active oxygen radicals in a dissolved oxygen system. Since caffeic acid (CA) can remove reactive oxygen species in the system, a sensitive detection method for CA on a paper-based chip was developed. Under the optimal conditions, this method showed a good linear response to CA in the range of 10 - 800 ng mL-1 with a limit of 3 ng mL-1. The proposed method had been used for the determination of CA in tea samples. The results may open a new avenue for the catalytic property on luminol CL system without extra oxidants.

A novel strategy for fabricating the paper-based valves on microfluidic paper-based analytical devices (μPADs) was described to control fluid in a user-friendly way. Initial prototypes of 3D μPADs manipulate the spatial distribution of fluid within the device. The movable paper channel in a different layer could be achieved using the channel's connection or disconnection to realize the valve function using plastic comb binding spines (PCBS). The entire valve manipulation process was similar to a desk calendar that can be flipped over and turned back. It is notable that this kind of PCBS valve can control a fluid in a simple and easy way without the timing setting or any trigger, and this advantage makes it user-friendly for untrained users to carry out the complex and high throughput operations. The reusable plastic comb binding spines greatly reduce the cost of fabricating paper-based valves. To evaluate the performance, the actual samples of Fe (II) and nitrite were successfully analyzed. We hope this method will introduce a new approach to fabrication of paper-based valves on μPADs in the future.

The effects of Mn(II) on Fenton system to treat papermaking wastewater and the mechanism of Mn(II) enhanced Fenton reaction were investigated in this study. The chemical oxygen demand (COD) removal efficiency was enhanced in the presence of Mn(II), which increased by 19% compared with that of the Fenton system alone. The pseudo-first order reaction kinetic rate constant of Mn(II)/Fenton system was 2.11 times higher than that of Fenton system. 67%–81% COD were removed with the increasing Mn(II) concentration from 0 to 0.8 g/L. COD removal efficiency was also enhanced in a wider pH range (3–7), which indicated the operation parameters of Fenton technology could be broadened to a milder condition. The study of the mechanism showed that Mn(II) participated in the oxidation and coagulation stages in Fenton system. In the oxidation stage, Mn(II) promotes the production of HO2•/ O2•−, then HO2•/ O2•− reacts with Fe(III) to accelerate the formation of Fe(II), and finally accelerates the production of HO•. Meantime MnMnO3 and Fe(OH)3 forms in the coagulation stage, facilitating the removal of suspended substances and a large amount of COD, which enhances the overall COD removal of papermaking wastewater. This study provided a detailed mechanism to improve practical applications of Fenton technology.

Interest in developing paper-based devices for point-of-care diagnostics in resource-limited settings has risen remarkably in recent decades. In this paper, we demonstrate what we refer to as “High Yield Passive Erythrocyte Removal” (HYPER) technology, which utilizes capillary forces in a unique cross-flow filtration for the separation of whole blood with performance comparable to centrifuges. As we will demonstrate, state-of-the-art passive blood separation methods implemented in paper-based systems exhibit rapid blood cell clogging on the filtration media or serum outlet and yield only about 10%−30% of the total serum present in the sample. Our innovation results from the inclusion of a differentiation pad, which exploits hydrodynamic effects to reduce the formation of a fouling layer on the blood filtration membrane resulting in more than 60% serum yield with undiluted whole blood as direct input. To demonstrate the effectiveness of the HYPER technology we implement it in a lateral flow system and demonstrate the accurate quantification of vitamin A and iron levels in whole blood samples in 15 minutes.

A lack of quality control tools limits the enforcement of fortification policies. In alignment with the World Health Organization&rsquo, s ASSURED criteria (affordable, sensitive, specific, user-friendly, rapid and robust, equipment-free, and deliverable), a paper-based assay that interfaces with a smartphone application for the quantification of iron fortificants is presented. The assay is based on the Ferrozine colorimetric method. The reaction started after deposition of the 5 &micro, L aqueous sample and drying. After developing color, pixel intensity values were obtained using a smartphone camera and image processing software or a mobile application, Nu3px. From these values, the actual iron concentration from ferrous sulfate and ferrous fumarate was calculated. The limits of detection, quantification, linearity, range, and errors (systematic and random) were ascertained. The paper-based values from real samples (wheat flour, nixtamalized corn flour, and infant formula) were compared against atomic emission spectroscopy. The comparison of several concentrations of atomic iron between the spectrophotometric and paper-based assays showed a strong positive linear correlation (y = 47.01x + 126.18, R2 = 0.9932). The dynamic range (5.0&ndash, 100 &micro, g/mL) and limit of detection (3.691 &micro, g/mL) of the paper-based assay are relevant for fortified food matrices. Random and systematic errors were 15.9% and + 8.65 &micro, g/g food, respectively. The concept can be applied to limited-resource settings to measure iron in fortified foods.

Microfluidic paper-based analytical devices (μPADs) were used to detect the iron ion content in the water of a natural hot spring in order to assess the applicability of this process to the environmental analysis of natural water. The μPADs were fabricated using a wax printer after the addition of hydroxylamine into the detection reservoirs to reduce Fe(3+) to Fe(2+), 1,10-phenanthroline for the forming of a complex, and poly(acrylic acid) for ion-pair formation with an acetate buffer (pH 4.7). The calibration curve of Fe(3+) showed a linearity that ranged from 100 to 1000 ppm in the semi-log plot whereas the color intensity was proportional to the concentration of Fe(3+) and ranged from 40 to 350 ppm. The calibration curve represented the daily fluctuation in successive experiments during four days, which indicated that a calibration curve must be constructed for each day. When freshly prepared μPADs were compared with stored ones, no significant difference was found. The μPADs were applied to the determination of Fe(3+) in a sample of water from a natural hot spring. Both the accuracy and the precision of the μPAD method were evaluated by comparisons with the results obtained via conventional spectrophotometry. The results of the μPADs were in good agreement with, but less precise than, those obtained via conventional spectrophotometry. Consequently, the μPADs offer advantages that include rapid and miniaturized operation, although the precision was poorer than that of conventional spectrophotometry.

Simultaneous precipitation (SP) using iron sulfates in the secondary treatment of elemental chlorine-free (ECF) kraft pulp mill wastewater was studied. In short-term pilot plant studies phosphorus reduction was improved from 58% up to 81% by adding 10 mgFe/L ferrous sulfate in the activated sludge (AS) process. The phosphorus reduction in full-scale experiment was about 80% when less than 10 mgFe/L was fed in with the influent of the AS plant. The reduction of phosphorus decreased with the dose of iron during the three month experiment. No notable change in either chemical oxygen demand (COD) or adsorbable organic halogen (AOX) reduction nor in the properties of sludge settling were observed during this SP experiment. Furthermore, no problems in sludge treatment due to increased iron concentrations in the waste sludge were reported. SP offers a simple way to decrease phosphorus discharges from AS plants instead of reliance on more expensive tertiary treatments.

Research in restoration and conservation is directed vs. more sustainable working materials, methods and technologies. Electrophoretic removal, from porous material, of undesired stains due to charged species is theoretically an interesting alternative to chemical cleaning methods, but the lack of specific and comprehensive research work leads to controversial opinions about the efficiency and the needed harmfulness for the treated objects. In this work paper, samples with artificial rust stains were subjected to electrophoretic cleaning treatments in mineral water as electrolyte. Treatments were carried out either in a bath by complete sample immersion between the distanced electrodes or by sample wetting and sandwiching between the electrodes. Evaluation of cleaning efficiency and treatment effects was based on colour change measurements (image analysis of scanned paper samples before and after the treatment and by colorimetric data via spectrophotometric measurements), investigation of morphological changes by SEM observations and folding endurance measurements.

A highly sensitive electrochemical (EC) biosensor combined with a 3D origami device for detection of Pb

Paper is one of the oldest and most abundant materials known to man. Recently, there has been a considerable interest in creating paper devices by combining paper with other functional materials. In this letter, we demonstrate a simple fabrication technique to create water-resistant ferro-patterns on wax paper using CO2 laser ablation. A resolution of about 100 mu m is achieved which is mostly limited by the cellulose fiber size (similar to 50 mu m) in the wax paper and can be improved by using a smaller cellulose matrix. Laser ablation results in modification of surface morphology and chemistry, leading to a change in surface energy. We also present a 2D model for ferrofluid deposition relating the size of the pattern to the amount of ferroparticles deposited on the surface. Finally, a paper gripper is presented to demonstrate advantages of our technique, which allows microscale patterning and machining in a single step.

The objective of this World Bank technical assistance has been to support the Government of Bangladesh’s (GoB) national capacity development framework for improving water and sanitation services (WSS) in Bangladesh, focusing on demand-responsive peer-to-peer or horizontal learning processes and improve horizontal accountability communication and monitoring systems to track progress in the sector. This technical assistance is in line with the World Bank country assistance strategy (CAS) which seeks to support the GoB target of ensuring safe drinking water and sanitation for all. It has contributed to strengthening the long-term capacity of the government, in particular the union Parishad (UP) which is responsible for ensuring water and sanitation services for all in Bangladesh.

Iron, an essential element for life, is regulated primarily at the level of uptake, storage, and transport in order to maintain sufficient availability for normal physiology. The key protein in iron homeostasis is a 25-amino-acid peptide, hepcidin, which modulates the amount of iron in the circulation by binding and promoting the degradation of the iron exporter ferroportin. Given the central importance of hepcidin, recent studies have focused on how iron is sensed and how the iron signal is transmitted to hepcidin. Mutations in a type II serine protease, matriptase-2/TMPRSS6, were recently identified to be associated with severe iron deficiency caused by inappropriately high levels of hepcidin expression. A key biologically relevant substrate for the proteolytic activity of matriptase-2/TMPRSS6 was found to be hemojuvelin, a cell surface protein that regulates hepcidin expression through a BMP/SMAD pathway. In this review, we discuss the putative role of matriptase-2/TMPRSS6 in iron homeostasis.

The main objective of this work is to study the technical viability of using the effluent generated in paper machines (white water) in the wash presses of the bleaching stage, reducing fresh water consumption. As a case study, the industrial process of Ripasa S.A. Celulose e Papel was evaluated. White water rate is about 700 m3/h and it is not possible to reuse all this volume in the bleaching stage without causing operational problems (fouling in tubes and clogging in the screens). A mass balance of the bleaching unit was developed in an electronic spreadsheet in order to evaluate the possibility of reducing fresh water consumption, using only a fraction of the available white water in the wash presses. To achieve this objective some physical-chemistry properties of the white water stream and of other streams of the process were determined. The maximum concentration of some non-process elements (Si, Ca, Mn and Fe), which could accumulate in the process, were determined in order to establish some parameters to allow process integration of the streams involved, considering operational constraints. The results obtained have shown that it is possible to reduce approximately by 13% the consumption of fresh water and this methodology has been satisfactory.

Exposure to metal-containing aerosols has been linked with adverse health outcomes for almost every organ in the human body. Commercially available techniques for quantifying particulate metals are time-intensive, laborious, and expensive; often sample analysis exceeds $100. We report a simple technique, based upon a distance-based detection motif, for quantifying metal concentrations of Ni, Cu, and Fe in airborne particulate matter using microfluidic paper-based analytical devices. Paper substrates are used to create sensors that are self-contained, self-timing, and require only a drop of sample for operation. Unlike other colorimetric approaches in paper microfluidics that rely on optical instrumentation for analysis, with distance-based detection, analyte is quantified visually based on the distance of a colorimetric reaction, similar to reading temperature on a thermometer. To demonstrate the effectiveness of this approach, Ni, Cu, and Fe were measured individually in single-channel devices; detection limits as low as 0.1, 0.1, and 0.05 μg were reported for Ni, Cu, and Fe. Multiplexed analysis of all three metals was achieved with detection limits of 1, 5, and 1 μg for Ni, Cu, and Fe. We also extended the dynamic range for multi-analyte detection by printing concentration gradients of colorimetric reagents using an off-the-shelf inkjet printer. Analyte selectivity was demonstrated for common interferences. To demonstrate utility of the method, Ni, Cu, and Fe were measured from samples of certified welding fume; levels measured with paper sensors matched known values determined gravimetrically.

This paper reports the continuous reductive amination of different molecules, including biomass-related compounds, over carbon-supported FeNi nanoparticles obtained on the basis of inexpensive and abundant metal precursors and cellulose. A biorefinery case study for the preparation of pyrrolidones via acid-catalyzed hydrolysis of glucose followed by reductive amination of the obtained levulinic acid is described.

The effect of Fenton's reagent (FR) on surface and dispersion properties of black liquor (BL) was investigated. These properties were compared to those of indulin C (IC), a commercial lignin, and egg lecithin (Le). FR was applied at two different bulk concentrations of H2O2 (160 and 320 mM). At pH 8, a minimum in surface tension for the Fenton treated BL was observed. The dispersant ability of BL, IC and Le in oil-in-water (O/W) emulsions was studied by measuring emulsion stability and drop size. It was found that the surface activity and emulsifying capability of BL were higher than those of IC. The emulsifying capability of Le was improved by the FR treatment at low H2O2 concentration.

Different advanced oxidation processes (AOPs) have been applied to remove the organic carbon content of a paper mill effluent originating from the Kraft pulp bleaching process. The considered AOPs were: TiO2-mediated heterogeneous photocatalysis, TiO2-mediated heterogeneous photocatalysis assisted with H2O2, TiO2-mediated heterogeneous photocatalysis coupled with Fenton, photo-Fenton, ozonation and ozonation with UV-A light irradiation. The application of the selected AOPs all resulted in a considerable decrease in dissolved organic carbon (DOC) content with variable treatment efficiencies depending upon the nature/type of the applied AOP. A Life Cycle Assessment (LCA) study was used as a tool to compare the different AOPs in terms of their environmental impact. Heterogeneous photocatalysis coupled with the Fenton’s reagent proved to have the lowest environmental impact accompanied with a moderate-to-high DOC removal rate. On the other hand, heterogeneous photocatalysis appeared to be the worst AOP both in terms of DOC abatement rate and environmental impact. For the studied AOPs, LCA has indicated that the environmental impact was attributable to the high electrical energy (power) consumption necessary to run a UV-A lamp or to produce ozone.

While recent evidence indicates that the generation of reactive oxygen species (ROS) and associated oxidative damage are frequently observed in fish populations with exposure to pulp and paper mill effluents, the potential for ROS generation from municipal sewage effluents has not been addressed. This study investigates the utility of measures of oxidative stress in delineating the effects of both pulp and paper mill and municipal sewage discharges. Longnose sucker (Catostomus catostomus) were collected below three pulp and paper mill and two municipal sewage effluent discharges over a 3-year period within the Wapiti and Athabasca River systems in northern Alberta. Biochemical responses in longnose sucker varied between the two rivers systems, with more pronounced changes occurring within the Wapiti River. Of the suite of biochemical parameters examined, fatty acyl-CoA oxidase (FAO) activity was the most sensitive indicator of pulp and paper mill exposure, but was only infrequently induced with exposure to municipal sewage effluent. Hepatic and gonadal 2-thiobarbituric acid reactive substances, lipid hydroperoxides, and hepatic free iron were less consistently elevated with exposure to pulp and paper mill effluent than FAO activity, and were also only infrequently altered with sewage effluent exposure. Hepatic ascorbic acid, liver somatic index, and condition factor were consistently altered with exposure to both sewage and pulp and paper mill effluents. While specific biochemical and organismal responses varied with effluents and time, the collective suite of oxidative stress endpoints proved to be useful tools in identifying relative influences of municipal sewage and pulp and paper mill effluent on fish populations in adjacent receiving waters.

Changes in material use, energy use and emissions profiles of industry are the result of complex interrelationships among a multitude of technological and economic drivers. To better understand and guide such changes requires that attention is paid to the time-varying consequences that technology and economic influences have on an industry's choice of inputs and its associated (desired and undesired) outputs. This paper lays out an approach to improving our understanding of the dynamics of large industrial systems. The approach combines engineering and econometric analysis with a detailed representation of an industry's capital stock structure. A transparent dynamic computer modeling approach is chosen to integrate information from these analyses in ways that foster participation of stakeholders from industry and government agencies in all stages of the modeling process-from problem definition and determination of system boundaries to generation of scenarios and interpretation of results. Three case studies of industrial energy use in the USA are presented-one each for the iron and steel, pulp and paper, and ethylene industry. Dynamic models of these industries are described and then used to investigate alternative carbon emissions and investment-led policies. A comparison of results clearly points towards two key issues: the need for industry specific policy approaches in order to effectively influence industrial energy use, fuel mix and carbon emissions, and the need for longer time horizons than have typically been chosen for the analysis of industrial responses to climate change policies.

Where malaria surveillance and health care is inadequate, iron supplements given without food can increase the severity of malarial infections. The likely explanation is that the rate of iron influx into the plasma from high-dose oral supplements exceeds the rate of iron binding to transferrin and a quantity of non-transferrin-bound iron (NTBI) is formed. It is proposed that NTBI increases the intensity of malarial infections by increasing the sequestration of malaria-infected red cells in the capillaries of the brain and intestine, causing more cerebral malaria and further increasing the permeability of the intestinal barrier to the passage of pathogens. Bacteremia is frequently reported in children with severe malaria. At the same time, high iron doses stimulate the growth of pathogenic bacteria in the stool, further increasing the potential for bacteremia. The normal immune response to malaria, as well as other infections and inflammatory disorders, is to prevent further microbial growth by stimulating hepcidin synthesis and preventing the passage of iron into the plasma. Iron absorption is decreased and the efficacy of the iron interventions would be expected to be lower in the presence of infections.

According to current environmental legislation concerned with water scarcity, paper industry is being forced to adopt a zero liquid effluent policy. In consequence, reverse osmosis (RO) systems are being assessed as the final step of effluent treatment trains aiming to recover final wastewater and reuse it as process water. One of the most important drawbacks of these treatments is the production of a retentated stream, which is usually highly loaded with biorecalcitrant organic matter and inorganics; and this effluent must meet current legislation stringent constraints before being ultimately disposed. The treatment of biorefractory RO retentate from a paper mill by several promising advanced oxidation processes (AOPs) – conventional Fenton, photo-Fenton and photocatalysis – was optimized considering the effect and interaction of reaction parameters; particularly using response surface methodology (RSM) when appropriate (Fenton processes). The economical cost of these treatments was also comparatively assessed. Photo-Fenton process was able to totally remove the COD of the retentate, and resulted even operatively cheaper at high COD removal levels than conventional Fenton, which achieved an 80% reduction of the COD at best. In addition, although these optimal results were produced at pH = 2.8, it was also tested that Fenton processes are able to achieve good COD reduction efficiencies (>60%) without adjusting the initial pH value, provided the natural pH of this wastewater was close to neutral. Finally, although TiO2-photocatalysis showed the least efficient and most expensive figures, it improved the biodegradability of the retentate, so its combination with a final biological step almost achieved the total removal of the COD.

Hepcidin is the central regulator of systemic iron homeostasis. Dysregulation of hepcidin production results in a variety of iron disorders. Hepcidin deficiency is the cause of iron overload in hereditary hemochromatosis, iron-loading anemias, and hepatitis C. Hepcidin excess is associated with anemia of inflammation, chronic kidney disease and iron-refractory iron deficiency anemia. Diagnostic and therapeutic applications of this new knowledge are beginning to emerge. Dr. Ernest Beutler played a significant role in advancing our understanding of the function of hepcidin. This review is dedicated to his memory.

The aim of this work was to evaluate the effect of chelator mediated-Fenton reaction (CMFR) on the chemical oxygen demand (COD) removal from bleaching kraft mill effluent. Effluent treatments were carried out to study the effect of the chelator 3, 4-dihydroxyphenylacetic acid (DOPAC), Fe3 + and H2O2 concentrations on COD removal. For optimization of COD removal, the methodology of statistical experimental design was employed. The estimated second-order polynomial multiple regression model predicts a maximum COD removal of 75.5% (COD/COD0 = 0.245) at the confidence level of 95%. Analysis of variance (ANOVA) showed a good coefficient of determination (R2) value of 0.90, thus ensuring a satisfactory adjustment of the second-order regression model with the experimental data. Indeed, CMFR proved to be a potential process to treat industrial effluents characterized by its high COD.

Most arsenic bearing solid residuals (ABSR) from water treatment will be disposed in nonhazardous landfills. The lack of an appropriate leaching test to predict arsenic mobilization from ABSR creates a need to evaluate the magnitude and mechanisms of arsenic release under landfill conditions. This work studies the leaching of arsenic and iron from a common ABSR, granular ferric hydroxide, in a laboratory-scale column that simulates the biological and physicochemical conditions of a mature, mixed solid waste landfill. The column operated for approximately 900 days and the mode of transport as well as chemical speciation of iron and arsenic changed with column age. Both iron and arsenic were readily mobilized under the anaerobic, reducing conditions. During the early stages of operation, most arsenic and iron leaching (80% and 65%, respectively) was associated with suspended particulate matter, and iron was lost proportionately faster than arsenic. In later stages, while the rate of iron leaching declined, the arsenic leaching rate increased greater than 7-fold. The final phase was characterized by dissolved species leaching. Future work on the development of standard batch leaching tests should take into account the dominant mobilization mechanisms identified in this work: solid associated transport, reductive sorbent dissolution, and microbially mediated arsenic reduction.

The effect of Kraft black liquor on the lipid peroxidation of rat homogenates was examined. The lipid peroxidation of homogenates from different organs (kidney, brain, lung, and liver) was induced by Fenton's reagent. The products of lipid peroxidation, lipid hydroperoxides and TBARS were measured by FOX method and TBA assay, respectively. It was found that black liquor significantly reduced the concentration of TBARS, but not the concentration of lipid hydroperoxides. This inhibition was directly proportional to the concentration of Kraft black liquor and the incubation temperature. Conclusively, the black liquor from pulp and paper industry exhibited an antioxidant activity.

Iron is an important component of the Earth's crust, but its own chemistry greatly limits utilisation and also sets the basis for its toxicity. The capacity of readily exchanging electrons in aerobic conditions makes iron essential for fundamental cell functions, such as DNA synthesis, transport of oxygen and electrons, and cell respiration. On the other hand, as humans have no means to control iron excretion, excess iron, regardless of the route of entry, accumulates in parenchymal organs and threatens cell viability. In fact, a number of disease states (that is, iron overload diseases) attributable to genetic or acquired factors are pathogenetically linked to excess body iron stores and iron removal therapy is an effective lifesaving strategy in such circumstances.

Diffuse reflectance spectroscopy can be successfully used for the quantitative determination of small amounts of pollutants like metals. The remission function was found to be linearly proportional to the concentration, when we applied the Kubelka-Munk equation. The color reactions of Cu(II), Co(II), and Ni(II) with dithiooxamide, were realised on filter paper. Reaction between Fe(III) and ammonium thiocyanate was realized on filter paper and gelatine matrix. All measurements were accomplished with a laboratory-constructed reflectometer. We have obtained a calibration curve by plotting the optical density of reflectance A(R) vs log of the mol l(-1) concentration. Limits of detection at the 10(-4) M level were estimated for all the compounds. Linear dynamic range extend over one order of magnitude and shows the potential of device for the quantitative analysis of environmental pollutants.

Efforts to reduce the high global prevalence of nutritional anemia require the use of both reliable laboratory assays to distinguish iron deficiency from other causes of anemia and cost-effective methods for collection of blood specimens under field conditions. The suitability of using small plasma samples spotted and dried on filter paper for measurements of plasma ferritin and transferrin receptor was evaluated in the present study.Blood specimens obtained from 73 male and 83 female subjects (19-40 years) representing a wide range of iron status were used to perform parallel measurements of plasma ferritin and transferrin receptor on whole plasma and spotted plasma samples.Ratio plots, evaluating the acceptability and precision of the spot method in ferritin and transferrin receptor assays, showed the expected proportion of data points within the 95% prediction interval. In the composite group of 156 subjects, both the whole plasma and plasma spot methods gave a geometric mean transferrin receptor/ferritin ratio of 18. The regression equation for the ratio was logy = 1.045 logx - 0.05126; r = 0.986; P0.0001. The ratio of transferrin receptor/ferritin determined from plasma spots correctly identified all 12 subjects with iron deficiency anemia compared with 11 of the 12 for whole plasma measurements.Measurements of ferritin and transferrin receptor on plasma spotted and dried on filter paper are comparable to whole plasma values for the identification of iron deficiency anemia. The use of dried plasma spots will facilitate the collection, storage, and transport of samples in epidemiological studies of anemia prevalence.

Amplification of DNA from whole blood collected on Guthrie card filter paper presents considerable technical obstacles due to the presence of natural PCR inhibitors (protein, heavy metals, heme, and heme degradation products) and low copy number of genomic material. For this purpose we evaluated guanidine thiocyanate‐impregnated filter paper (GT‐903), a DNA collection device designed specifically to bind PCR inhibitors and preserve DNA in an aqueous extractable form. Compared to standard 903, which retains DNA and elutes inhibitors during aqueous extraction, we found GT‐903 retained 90% of protein, hemoglobin, and iron. SDS‐PAGE analysis indicated that the majority of the protein released from standard 903 corresponded to albumin (70‐) and globin (15‐kDa); negligible levels of these proteins were eluted from GT‐903. To evaluate PCR efficiency, we amplified the 491 bp region encoding the cystic fibrosis ΔF508 mutation. Using comparable template, we found GT‐903 amplification more efficient than standard 903 following qualitative (TBE‐PAGE) and quantitative (anti‐dsDNA EIA) determination. We conclude that GT‐903 provides a good DNA collection device and addresses the complications associated with natural PCR inhibitors. J. Clin. Lab. Anal. 11:87–93. © 1997 Wiley‐Liss, Inc.

The aim of this study was to investigate a possible relationship between exposure to sulfides and disturbances of the synthesis of heme and the erythrocytes. Eighteen workers exposed to sulfides at a pulp and paper plant were examined and compared with individually matched referents from a thermomechanical pulp plant without such exposure. The exposure levels of methylmercaptan, dimethylsulfide, and dimethyldisulfide were low. However, five subjects were exposed to high levels of short duration, and their data were analyzed separately. The activity of the enzymes delta-aminolevulinic acid synthase and heme synthase in reticulocytes, characteristics of the erythrocytes, and the iron status were analyzed. A minor decrease, not statistically significant, was observed for the enzymes among the five highly exposed subjects. However, the concentrations of iron and transferrin were elevated and the concentration of ferritin was low in comparison to the corresponding levels of the referents. This combination will not occur spontaneously. A previous study indicated that sulfides may inhibit heme synthesis, and the present study suggests that they may also disturb iron metabolism.

Mutants of Escherichia coli K-12 blocked in each of the three enzymatic reactions between chorismate and 2,3-dihydroxybenzoate, in the pathway leading to the iron-sequestering compound enterochelin, have been isolated and biochemically characterized. The three genes concerned (designated entA, entB and entC ) have been shown to be clustered on the chromosome between purE and gal and to be located near minute 14 by cotransduction with the purE, lip , and fep genes. entA, entB , and entC were shown to be the structural genes for 2,3-dihydro-2,3-dihydroxybenzoate dehydrogenase, 2,3-dihydro-2,3-dihydroxybenzoate synthetase, and isochorismate synthetase, respectively.