Search

Copyright of China Mechanical Engineering is the property of Editorial Board of China Mechanical Engineering and its content may not be copied or emailed to multiple sites or posted to a listserv without the copyright holder's express written permission. However, users may print, download, or email articles for individual use. This abstract may be abridged. No warranty is given about the accuracy of the copy. Users should refer to the original published version of the material for the full abstract. (Copyright applies to all Abstracts.)

To serve in a corrosive environment, a corrosion-resistant rail steel U68CuCr has been developed in China. In the present study, the wear behavior of U68CuCr was investigated and compared with the commonly used rail steel U71MnG by rolling contact friction tests. The results indicate that the mass loss and wear rate of U68CuCr are smaller than those of U71MnG. The wear rates under the dry condition are smaller than those under the water–oil condition. In addition, the formation of oxide and spalling finally achieves the dynamic equilibrium on the surface of two types of rail steels. However, the duration of the lubricative and protective wear debris layer is longer for U68CuCr. Moreover, the worn surface of U68CuCr is relatively flat, while the wear regime of U71MnG is more severe. The amount and volume of the spalling pits of U68CuCr are smaller. Furthermore, the plastic deformation layers are shallower, and the rolling contact fatigue cracks are shorter for U68CuCr because of the finer pearlitic microstructure. The results prove that the U68CuCr rail steel shows good wear-resistant ability, suggesting its superior suitability for application in high-speed railways in a marine environment. [ABSTRACT FROM AUTHOR]

• Typical factors affecting the wheel-rail dynamic response are comprehensively considered to reveal the short-term load characteristics of frog under complex conditions. Meanwhile, based on the ellipsoidal Gaussian extrapolation theory, long-term wheel-rail load characteristics are obtained. • Combined with the strain energy fatigue parameter theory, a prediction method for the fatigue life of nose rail under complex conditions based on load spectrum preparation was proposed. • The location between the 30 mm and 35 mm sections of the nose rail has the shortest rolling contact fatigue crack initiation life and should be focused on during damage inspection. The rail profile irregular variation and wheel-rail relationships complexity at the gap in the frog enhance the wheel-rail impact forces, frequently resulting in rolling fatigue damage under complex cyclic loads. Therefore, it is particularly important to study the transient rolling contact load characteristics of fixed frog and to compile load spectrum considering various complex conditions for analyzing the fatigue damage of frog and extending the service life of structure. In this paper, a 3D transient FE model of wheelset and fixed frog is established, revealing rolling contact behavior of wheel-rail in frog area from both macro and mesoscopic perspectives. In order to investigate long-term load characteristics of wheel and rail under complex service conditions, the changes of line conditions, load conditions, rail wear state and other influencing factors in actual operation are taken into account. Based on elliptic Gaussian kernel density theory, a method for compiling the load spectrum of fixed frog nose rail is proposed, and the FP method is used for fatigue crack initiation life prediction of nose rail in fixed frog. The results show that the force state is more severe when passing through the frog in straight reverse direction, and resonance is prone to occur in the third and fifth vertical bending modes of the frog, as well as the fourth and sixth vertical bending modes of the stock rail. The increase in factors such as speed, axle load, wheelset lateral displacement towards frog side and wing rail wear will exacerbate wheel-rail impact and shorten frog service life. Different factors have an impact on the overall amplitude, oscillation center range, and maximum frequency load of the wheel-rail force in the long-term load spectrum of the frog. The fatigue crack initiation area of nose rail is mainly in 30 mm–35 mm sections, which is consistent with the on-site flaw detection results, verifying the accuracy of the calculation method developed in this paper. [ABSTRACT FROM AUTHOR]

Track–vehicle severe interaction on track with small curve radius results in rail wear and corrugation, and wheel polygonization, which drain considerable resources for rail grinding and wheels re-profiling in metro lines. To reduce the damage caused by track-vehicle severe interaction, the paper analyzes the reasons leading to rail wear and then proposes an architecture of a metro vehicle with independently rotating wheels driven directly by permanent magnet synchronous motors. The architecture is axle guidance, offered by passive linkages, which ensures that all axles are oriented radially, while control strategy was kept as simple as possible, identifying only two basic traction conditions. The concept is first discussed and then validated through a comprehensive set of running dynamics simulation performed with a multibody software to evaluate rail wear and rolling contact fatigue in traction/braking, coasting with different cant deficiency/excess conditions. The multibody dynamics simulation shows that the proposed architecture is virtually capable of avoiding both wear and rolling contact fatigue damages, and achieves the highest possible track friendliness. The concept of the proposed architecture is a track-fiendly metro architecture and could be a good reference for reducing rail-track interaction damages and maintainace cost. [ABSTRACT FROM AUTHOR]

To investigate the relationship between surface microstructure and wear mechanism in D2/U71Mn wheel-rail material under different contact stress conditions, rolling wear tests using a GPM-40 wear machine to simulate the wheel-rail operation was performed. After wear tests, an optical microscope (OM), scanning electron microscope (SEM) and micro-hardness testers were used to characterize the microstructure and fatigue wear cracks. The results show that the thickness of the plastic deformation layer and surface hardness is increased with the increase of contact stress. Under high contact stress condition (1200 MPa), the severe plastic deformation layer led to the formation of fatigue wear of wheel-rail samples. Under a contact stress of 700 MPa, the wear mechanism of samples is adhesive wear and wear rate is low. With the increase of contact stress, the fatigue cracks are gradually severe. Under a contact stress of 1200 MPa, the wear mechanism of samples becomes fatigue wear and the fatigue wear cracks cause the increase of wear rate. The fatigue wear can accelerate the wear failure of wheel-rail samples. The fatigue wear cracks of wheel samples are severer than that of rail samples due to both the rate of plastic strain and the content of proeutectoid ferrite. [ABSTRACT FROM AUTHOR]